Search Documents

Same-batch and non-blind as well as blind pulp duplicates are often submitted as quality assurance/quality control (QA/QC) control samples to a routine laboratory along with routine assays (and other control samples such as reference material samples). The current ways of interpreting the results of duplicate assays to derive QA/QC conclusions and decisions, however, has not yet been formalised in a scientific manner. The current, prevailing approach and its limitations are reviewed and a new method is proposed as a substitute tool. This new tool should allow for operational error detection on a batch per batch basis (ie batch rejection) as well as laboratory performance assessment with time on reproducibility.

Jan 1, 2008

By S R. La Brooy, T Giraudo, I C. Ritchie

The treatment plant at the Macraes Gold Project in New Zealand processes a carbonaceous, refractory sulphide gold ore. Since its commissioning in 1990, there has been a programme of continuous improvement of the plant, leading to higher recovery, increased throughput and low operating costs. During this time, a number of processes for treating both, or either, the preg-robbing carbonaceous fraction of the ore and the refractory sulfide fraction have been evaluated, trialed and utilised. The latest phase involves the installation by Minproc of plant utilising Newmont Gold's Pressure Oxidation Technology, a process which is anticipated to mitigate both problem factors when commissioned in 1999.

Jan 1, 1998

By Bauduin C. Besix

The Eurocode 7 "Geotechnical Design" is based on "Limit State Design", tackling the uncertainties as much as possible at their source through: - selection of characteristic values of variables (loads, soil properties, pile resistance,...); - partial factors applied on the characteristic values; - model factors to account explicitly for uncertainties of the calculation rule if necessary. Eurocode 7 will propose three "design approaches". The selection of one of them will be by National Determination. For pile design, the approaches are: - approach 1 is a "material factoring approach" at load side and a "resistance factoring approach" at resistance side. The structural and geotechnical design are checked for both of two separate sets of partial factors. - approach 2 is a "load and resistance factoring approach" and is in several aspects close to a deterministic approach. The design is checked for one set of partial factors. - approach 3 is a material factoring approach, at load as well as at resistance side. The design is checked for one set of factors. The aim of this paper is to introduce to the design of pile foundations based on pile load tests and on ground test results (semi-empirical and analytical methods) in the frame-work of the three design approaches. Detailed attention is devoted to: - the selection of the characteristic value of the pile resistance, accounting for spatial variability and stiffness of the structure; - the reliability of the prediction of the pile resistance using analytical or semi-empirical methods which may be accounted for through a "model factor". The results of a large test campaign on screw piles in OC Clay and a calculation example illustrate the proposed procedure when calculation rules using CPT results are used.

Jan 1, 2002

By Joan T. May

The Bureau of Mines conducted laboratory tests to evaluate the production of high-purity H3P04 by HCl digestion and solvent extraction. Both batch and bench-scale continuous tests were made. Western phosphate rock concentrates were acidulated with HCI, and the digestion liquors were processed by solvent extraction. Phosphoric acid was extracted with isoamyl alcohol and recovered from the organic extract by contact with an NH4F solution. This solution was fractionally distilled to yield high-purity H3P04. The raffinate from solvent extraction was treated with lime to precipitate CaF2, which was subjected to steam pyrolysis to generate HF. This method was successful in recovering 95 pet of the phosphate and 80 pct of the fluoride contained in the concentrates.

Jan 1, 1976

By Yunyan Wang

Diagrams of pc-pH for the complex ions concentration and pH value and -g- for activity coefficient and ionic strength ln±MnSOI4had been drew based on the thermodynamic principle of coordination chemistry and combined with Pitzer theory at 298.15K. The diagram of -g- indicated that -gincreased sharply from 0.0000 up to 1.2147 when I changed from 0.00 ln±MnSOIln4±MnSO4to 0.09; The increase of -gbecame slowly when I was more than 1.00 and less than 1.69; kept still when I ln±MnSOln4-g±MnSO4was more than 2.25 and less than 4.00. Diagrams of pc-pH illustrated that the minimum solubility of Mn(OH)2(s) increased with the increase of I, the pc increased from 6.5 to 5.5 when I increased from 0.00 to 4.00; The pH of the minimum solubility of Mn(OH)2(s) increased with the increase of I, the pH increased from 11.80 to 12.76 when I increased from 0.00 to 2.89, the pH kept still when I (I was less than 4.0) increased. There is single function relationship between the minimum solubility of Mn(OH)2(s) and relevant pH in different I.

Jan 1, 2010

By P Mulvey

"Currently mine process studies and geochemical waste characterisation are considered as two interdependent studies, necessary for the development of the mine and inclusion in the environmental impact statement (EIS). Geochemical waste characterisation will utilise the simulated tailings produced by the mine process studies team to understand the behaviour of the tailings, but the two teams rarely integrate these to develop a coherent and agreed final design.Thorough mine waste geochemical assessments can develop processes to minimise environmental harm, resulting in substantial savings in the decommissioning, closure and rehabilitation phases, and may also be able to address changes in mineral processing methods that can result in substantial savings in process inputs, or even recovery of metal concentrates.Based on geochemical waste characterisation, the full cost of waste management can be calculated and incorporated into the costing of milling.  This allows for a more effective evaluation of the metallurgy.  A number of examples are presented in which substantial improvements have been made from the collaboration of both the metallurgical and geochemical teams during planning and the metallurgical team and environmental team during operations.*This paper is only available for individual download. It is not included in the conference proceedings*CITATION:Mulvey, P, 2013. Optimising metallurgy at the planning stage to minimise environmental impact - a feedback loop from geochemical waste characterisation, presented to MetPlant 2013 Conference (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By Mika Muinonen

"Dewatering of nickel concentrate at the INCO Thompson integrated mine-metallurgical site takes place within the smelter plant. The eight original 60 foot diameter cable torque thickeners of which four were operational and eight Dorrco internal drum filters have been replaced with a single Outokumpu high rate thickener and a single Lasta pressure filter. The modernization has resulted in a filter cake which has a more stable and lower moisture content. Control of the entire dewatering process has been improved and costs have been reduced.Typical filter cake produced from the Dorrco filters during processing of high tonnages of Birchtree mine ore was ~20% moisture vs. ~13% moisture for concentrate produced from the Thompson mine ore. The high moistures were correlated with the amount of fine magnesium silicate gangue in the concentrate. As Birchtree ore processing rates have increased, this filter cake moisture became unacceptable because of material handling problems and the impact on furnace metallurgy. The Dorrco filters were replaced with the Lasta filter in 2003 that has consistently produced filter cake at ~11% moisture.This paper summarizes the piloting, design, installation and commissioning of the modernized dewatering circuit.INTRODUCTIONThe Thompson integrated nickel processing facility was built in 1958 and originally consisted of a mine-mill-smelter and, soon after, a refinery.Nickel concentrate is pumped from the mill as a dilute slurry directly to the smelter facility ~200 meters along an unheated pipe trestle. Originally, nickel concentrate was de-watered using up to 8 conventional 60-foot diameter thickeners and 8 internal vacuum drum filters."

Jan 1, 2006

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Mehmet Aksoy, Kagan Ozdemire

With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision. Therefore, determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. Although too many research studies had been carried out in the past in order to eliminate environmental issues produced from blasting unfortunately a general approach or formula has not been established yet because of the complexity of the matter. In addition to the wave and ground motion characteristics, the complexity of blasting parameters and site factors restrict the developing a general criterion. So experimental site-specific studies should be still done in order to predict and control blasting effects. This paper presents the results of ground vibration measurements carried out in Espey Open-Pit Boron (Colemanite) Mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study, ground vibration components were measured for 13 shots during bench blast optimisation studies in order to predict peak particle velocity level for this site. In blasting operations; ANFO and Powergel Magnum 600 (blasting agent), Powergel Magnum (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 4 different types vibration monitors (3 White Mini-Seis and 1 Instantel Minimate Plus Models). Then, the data pairs of scaled distance and particle velocity obtained from the 38 record events were analysed statistically. At the end of statistical evaluation of the data pairs, an empirical relation which gives average line at 95% confidence level and upper bound 95% prediction line with a reasonable correlation coefficient was established between peak particle velocity and scaled distance.

Jan 1, 2005

By K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in-situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in-situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in one area of the mine that contains Argillite and is relatively homogeneous. This also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for Argillite will be updated as more tests are conducted, and the model will be extended to the other four primary rock types at the Asarco Mission mine.

Jan 1, 2011

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine ventilation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which accounts for a major portion of the market for coal, received further study. Unique power generation systems, including coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jan 1, 1965

By T J. V Duffy, L H. D Siahaan, P G. Albert

G-ResourcesÆ Martabe Mine in North Sumatra, Indonesia, is a US$700 M world-class and world-scale operation in a country which, with a few notable smaller scale exceptions, has had no significant hard rock mining development in more than ten years.The mine was commissioned in the middle part of 2012 and poured first gold on 24 July. At full production Martabe will produce 250 000 oz/a of gold and 2 - 3 Moz/a of silver at cash costs in the lowest quartile. The mine location is on the west coast of North Sumatra, which experiences annual rainfall of 4 m with no notable dry season, adjacent to seismically active fault zones, and relatively close to a rural community of 31 000 people with no significant industrial experience.The management team has successfully forged strong links with the various government departments and levels in Jakarta, North Sumatra Province and the local Regencies; developed long-term relationships with the various community groups within the local district of Batangtoru to build a sustainable social licence; has dealt with the physical and environmental challenges presented by the project location, and has successfully raised more than US$900 M over a period of three years for the original acquisition then the development of the project.Whilst in its infancy of operation, the mine is set up to deliver a long-term sustainable future for the company, the shareholders, and the people of Batangtoru and all stakeholders generally. The quality of the project execution and commitment by the company will ensure that maximum value can be delivered from Martabe, not just for the current mine life but from the significant exploration potential that exists on the large tenement area that the company has access to for 30 plus years.This paper will deal with the physical challenges associated with the design, the Indonesian government regulatory requirements for mine development, the social aspects of building a world-class project in a developing area, the in-country commitment necessary for any project development anywhere in the world and the successful funding arrangements for the mine development.CITATION:Albert, P G, Siahaan, L H D and Duffy, T J V, 2012. Building AsiaÆs latest hard rock mine, in Proceedings International Mine Management 2012, pp 189-204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By Mike Tracy

This section of the Handbook deals with general principles to be evaluated in the development of a mining operation. It addresses the major issues that must be examined to fully evaluate a mining venture. Of course, one of the main topics to be evaluated is mine planning, which is covered in more detail in other sections (13, 17) of the Handbook and should be referenced in mine development projects. The topics to be discussed in this introduction include equipment and supplies, infrastructure, utilities, and project management. In any of the aspects mentioned, the current existing conditions at or near the mine site must be evaluated. This will include assessment of current use of utilities, infrastructure, housing, equipment suppliers, etc., as well as anticipated growth, both in the supply aspect of these systems as well as projected usage on these systems. After full assessment of both these aspects, an evaluation must be made as to the requirements the project will place on these items. Assessment must be made as to any up-grades required to bring the project on line, what impact the project will have on existing or expanded systems, and anticipated future growth impacts on support systems not only of the project but of other surrounding industry and urban devel-opment

Jan 1, 2008

By V. M. Shick

For practical purposes of the use of information resources in the field of geomechanics and mine surveying with accepted mining technology in mines, the authors have developed the packaged software programs of the survey-geomechanical information system with database objects of mine field. This system enables to execute the graphical representation of workings layout in preset scale, axonometric projection, the zones of higher ground pressure: program packages for calculations of rock pressure manifestations and for selection of suitable support facilities for the permanent, development and active workings and vertical shafts based on the information resources of the State Research Institute of Mining Geomechanics & Mine Surveying (VNIMI). The program packages are applied at coal mines in Russia and in Kazakhstan. The profitable operation of coal mines can be reached only by the combined optimal engineering decisions in mine working's laying-out and their reliability and safety at the stages of their designing and exploitation, and with minimal harm of the environment as well. This problem is being complicated by the fact that today the mining-practicing engineers and designers are ordinarily facing the problem " of an information barrier", when the complexity of controlling systems exceeds the potentialities of traditional management of production practice. Coal mine is a typical representative of complicated systems, because the information about geological structure, physicomechanical properties and stress-strain state of rock mass are of fragmentary character and insufficiently reliable. A mine has a developed network of interrelated workings, by the way, some of them are productive ones being subjected to control to a certain extent, and some of them are abandoned ones being noncontrollable and hazardous in rushes of water, gas, pulp and fire. The ground pressure forces cause the disintegration of rock mass growing with depth. The progress of mining operations constantly changes the geomechanical situation forming the zones of bearing pressure, stress relieving, coal falling, as well as it leads to the pulp movement on the earth surface, breaks the ground water flow, causes deformations and changes in stability of buildings, constructions and natural objects on the earth surface. One should take into account the existence of hazardous zones within the mine field, i.e. the zones of elevated ground pressure, geological dislocations and those ones under natural water reservoirs, ponds, etc. Major coal seams are prone to rock bursts, sudden outbursts, bleeding, endogenic fire. It is obvious, that in practice it is extremely difficult to account for the mentioned above factors in their interrelation.

Jan 1, 1996

If one can embrace the medical analogue, much of the mining industry currently suffers from a massive bacterial infection. When pyrite-bearing or sulfide-bearing rock formations, tailings, or mine wastes are infected by Acidithiobacillus ferro-oxidans, the likelihood of forming acid rock drainage (ARD) is almost guaranteed. The ?pharmacy? of antibiotics available is extensive, ranging from solid alkaline amendments like limestone to liquid ?medicines? such as sodium lauryl sulfate, sodium thiocyanate, waste milk, and bipolar lipids. Unfortunately, the ?geo-medical? teams of geochemists, microbiologists, engineers, and mine managers lack the tools to surgically apply these active ingredients where they are needed most with a minimum of waste. Distribution of fine grained limestone on the surface of an acidic mine waste dump is analogous to applying a bandage soaked in antacid to treat an upset stomach. The implementation of up-to-date best management practices has not healed the patient; an equivalent combination of hypodermic needle, cyber knife, and arthroscopic probe is clearly needed. Using an engineered, flow-able or pumpable foam or pHoam? as the medicinally analogous ?dextrose delivery solution? for solid and/or liquid ?geo-antibiotics?, the authors have combined off-the-shelf technologies that have been previously applied in solving geotechnical problems in the mining industry. A patent for the innovative process is pending. This paper discusses method concepts and the advantages it could provide over conventional BMPs.

Jan 1, 2012

By Tim Peterson

Factors Controlling Stability Stability of slopes in soft rock, waste dumps or soils is governed by three factors: ?Slope configuration ?Groundwater ?Shear strength

Jan 1, 2004

By J. Alexis, G. Ye, E. Burström

Over the past twenty years the 3 MW DC arc furnace at MEFOS has been frequently used for development of new processes. These processes include recovery of valuable metals from slag, sludge and dust from steel and other metallurgical industry, treatment of ashes from power plant and incinerators, smelting reduction of minerals and zinc recovery from EAF dust. The process characteristics of the DC arc furnace operation in terms of: ? selective reduction, ? total reduction, ? process stability and flexibility, ? dust carry-over, ? thermodynamic conditions provided in the hot spot area, ? precision in composing slag products These are analysed and described in this paper based on technical results from selected test campaigns over the years and thermodynamic considerations. The electromagnetic properties of DC arcs beneath the electrode have been studied by CFD simulation. The calculated result enables us to understand some interesting technical phenomena observed. The heat balance has also been considered based on data obtained from test campaigns and heat balance calculation.

Jan 1, 2004

By Thomas C. Shapiro

This is the second in a series of articles on microcomputers and applications in the minerals industry. The first article (ME, Feb., page 129) discussed microcomputer terms and concepts. This article will discuss software for geology and mining. The third article will cover plant, administrative, and geotechnical software applications. Introduction Geology and exploration are areas where computers have a natural fit. Large volumes of data need to be tabulated, evaluated, and made into maps and reports that allow geologists and management to make a decision on a project or mine. Until recently, the programs that performed these tasks were cumbersome and not user friendly by any stretch of the imagination. Learning time to become an expert in these programs typically would be six months or more. The computers needed to run these programs are expensive mainframes. Several years ago, the use of minicomputers became popular because of their lower cost. Programs were adapted to fit these smaller machines and became friendlier. With the advent of micros, many programs. were rewritten and used the screen capability more effectively, thus providing a real advance in user interface. Programs and Price The definition of micro, mini, and mainframe is becoming blurred. For the purposes of this article, micro refers to either an eight- or 16-bit computer, costing less than $10,000 and, more typically, under $5,000. Mini refers to a 16- or 32-bit computer that typically costs more than $25,000. Mainframe refers to a 32-bit or larger computer that costs more than $250,000. There is a large gray area between micros and minis, and minis and mainframes. Technology and prices are changing so fast that the traditional definitions have become almost meaningless and price has become a better guide. With the arrival of the minicomputer, costs for hardware began to fall, but the programs have tended to remain unfriendly. In some cases, the minicomputer acted as a front end to the mainframe. Cost of both the programs and minicomputers could easily run a minimum of $70,000. A total cost of $200,000 would not have been out of line. The average geologist and company would have a great deal of difficulty justifying such a purchase. The advent of the microcomputer has changed all that. For $3,500 to $5,000, one can buy a 16-bit micro and a printer. Plotters with six pens are available for $2,000 that will produce a 280- x 430-mm (11- x17-in.) map. For several hundred dollars, software is available to act as a word processor, an economic spread sheet, or to perform ground water calculations. In fact, some programs are available for free. Some of these programs are relatively easy to learn. In addition, programs are being developed daily that are easy to use. More importantly, large programs that once ran only on mainframes are being converted

Jan 3, 1984

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

By R. Karl Zipf

This report presents nearly all structural data available from explosion tests of 20-psi mine ventilation seals and concrete-block ventilation stoppings that were conducted by the National Institute for Occupational Safety and Health during 1997?2008. Although the seals tested were designed to meet the former federal 20-psi pressure design standard, the structural information contained herein on these seal tests will facilitate the analysis and design of coal mine seals that meet the new explosion pressure design criteria of 50 and 120 psi as set forth in the Mine Safety and Health Administration (MSHA)?s final rule on ?Sealing of Abandoned Areas.? The seal testing data are organized into six broad categories of seal structures based on the materials used and the construction method for those 20-psi seals: 1. Concretelike materials with steel reinforcement and reinforcement bar anchorage to rock 2. Pumpable cementitious materials of varying compressive strengths with no steel reinforcement and no hitching 3. Articulated structures such as solid-concrete-block seals and ventilation stoppings made of solid and hollow-core concrete blocks 4. Polymer and aggregate materials without hitching 5. Wood-crib-block seals with or without hitching 6. Articulated structures such as lightweight blocks with or without hitching This summary contains data on 52 different structures in the above categories?44 seals and 8 ventilation stoppings. The structural data sets include the applied loading on the tested seal represented by a pressure-time curve and, when available, the measured seal response represented by a displacement-time curve. The structural data sets enable the calibration and verification of numerical models of seal behavior at the 20-psi level, which may then facilitate future structural analyses of seal designs for the new 50- and 120-psi explosion pressure design criteria.

Aug 1, 2008

By J. E. Nesset

"I had been requested earlier this year by MetSoc, our sister society of CIM, to contribute a chapter on technical developments in Canadian mineral processing over the past 50 years to their 50th Anniversary volume. Accepting the challenge of assembling such a chapter seemed at first a reasonably straightforward task, until one realises that the list of contributions by Canadians to mineral processing over this period has been more than just significant. It turns out to have been an extraordinarily fertile time for innovation and impact for Canadian-based technology. The list is necessarily a subjective one, however I had no trouble identifying twenty technology developments that are clearly outstanding, and there are undoubtedly others. As much as possible, I approached the individuals themselves who played key roles in each technology and asked that they tell the “story”. Without exception, all who were invited accepted eagerly and delivered more than I had hoped for. The technologies have been grouped into those that are truly Canadian innovations, such as the Knelson gravity concentrator and the McGill gas dispersion sensors in flotation, and technologies where Canadians and Canada played a very significant role in their success and implementation, such as AG/SAG grinding and ion-beam surface analysis. Also included are what may be termed technology transfer initiatives and institutions that have risen to a world class level, such as SGS Lakefield and the Canadian Mineral Processors Society of CIM. The challenge is now for the coming generation to continue this record of innovation and contribution to the industry, and that includes the (mostly) Canadian mining and metallurgical companies who have taken the longer term view and supported many of these initiatives, through their critical early years, with both financing and project sites for these ideas. Let us hope that the current trend of mining company globalization will not dampen their enthusiasm to participate. This plenary presentation will highlight many of these technologies, the individuals behind them, and their significance to the mineral processing industry."

Jan 1, 2012