Search Documents

By Z Li, A Fleming, S Webster, L Snyman

Northparkes Mines is developing the E26 Lift 1 North block cave mine, which is adjoined to the existing E26 cave. This paper presents the challenges and methods used to design the ground support system during the feasibility study. Calibrated numerical simulations were conducted to forecast the levels of rock mass damage and to assist the ground support design. Generally, low to moderate rock mass damage is forecast on the extraction and undercut levels. However, poor ground conditions are expected in sheared and preconditioned zones adjacent the existing E26 cave. This will result in difficult ground conditions during development, undercutting and drawbell establishment. Empirical assessments were conducted to make sure the ground support system is able to handle both the static and dynamic load demand, and to accommodate the deformation values. A safety factor of 1.5 was used for the designs to cover the unknown rock mass conditions and potential for larger seismic events. Learnings from the E26 Lift 1 and SLC, also mining against the E26 cave, are incorporated into the design. Fibrecrete, mesh and resin bolts / mechanical anchors are the primary ground support system used, and cable bolts for intersections with a span of more than 6 m. Following undercutting and during the operating life of the mine, secondary ground support and rehabilitation will be required.

Mar 15, 2021

By Almer E. C. van der Stoel

"Abstract This paper deals with assessing the bearing capacity of existing wood pile foundations. With a wide range of restoration projects being performed in the Netherlands, on many locations deep excavations need to be constructed next to existing, many times listed buildings. The building are founded on piles that are often centuries old, so a close evaluation of the remaining bearing capacity, combined with and assessment of the influence of the excavation is in place.After giving an introduction on Dutch pile foundations, a methodology is described to assess the bearing capacity. Aspects as physical foundation investigation, determination of the current bearing capacity and a calculation of the bearing capacity in the new situation are discussed. The results of both analytical and Plaxis calculations are outlined, focussing on how to practically use this approach in renovation projects. Finally, cases studies of the successful application of this approach in major renovation projects in Amsterdam, such as the Conservatorium Hotel and the New Rijksmuseum are used to illustrate the successful application of this approach.A Short Dutch Pile Foundation History (based on Van der Stoel, 2001)The first houses built in Amsterdam, in the 12th century, were very light constructions of timber without foundations. Because of the soft peat layers found in Amsterdam, the houses there suffered from damage due to settlement. In the 13th century, castles and churches were increasingly built of bricks, which made it necessary to provide support for bigger loads. Under the wall of the construction a trench was dug, and this was filled on either side by alder fascines. Between the fascines small wood piles were driven (by hand) on which another series of fascines was put. On top of this construction, were placed oak slabs on which the bricks were then laid. From that moment on, a problem was caused by the decay of wood foundation elements in the humid soil. In 1503 a law was introduced forbidding building foundations on public streets without permission of the Building Inspection (to keep the fronts of the buildings in a straight line). In 1528 a law requiring permission from the local authorities for all building activities replaced this law. In this period developments started which led to the use of the type of foundation that can be considered the mother of the current “typical” Dutch pile foundation. The piles used in this period were shaft- bearing piles about 5 to 7 meters long. The mostly pine piles were driven between oak beams, which were placed on either sides of a trench, after which other oak beams were laid across at regular spaces: the so called “pile bent” pile foundation (Figure 1)."

Jan 1, 2014

By Gerald L. Finlinger

This Bureau of Mines publication reviews underground methane drainage programs being conducted in various coalbeds. Equipment used in drainage programs such as drills, underground pipelines, and methane monitoring systems is described.

Jan 1, 1980

By F. Parada Torres

Xstrata Tintaya S.A. opera el yacimiento a tajo abierto y procesa el mineral en dos plantas: Planta Concentradora de Sulfuros y Planta de Lixiviación de Óxidos, donde anteriormente consideraba al mineral mixto complejo como intratable en la planta concentradora, por lo que se le destinó a ser tratado como óxido marginal en la planta de lixiviación. En este sentido, el presente texto describe el nuevo tratamiento al mineral complejo en la planta concentradora. De forma que se busca definir las variables geometalúrgicas del mineral de Chabuca Norte, optimizar los procesos metalúrgicos del mineral mixto mediante la investigación geometalúrgica, así como correlacionar el entendimiento de la geología y alteraciones del yacimiento con los procesos metalúrgicos y crear valor mediante la optimización de la tasa de tonelaje de tratamiento y el incremento del porcentaje de recuperación de cobre en el proceso.

Sep 12, 2011

By M. Ksiazek

Keywords: Thermal conductivity, thermal diffusivity, flash method, specific heat capacity, manganese ore Manganese ferro-alloys manufacturing involves a combination of quality raw materials and an energy source to produce high-quality products with low energy consumption. The thermal properties of manganese raw materials such as ores, sinters, and briquettes, are among the many factors that determine the amount of energy needed for processing. Thermal expansion, thermal diffusivity, conductivity, and apparent specific heat capacity of solid samples and compacted powder samples of manganese ores were examined from room temperature to 1000 °C. The effect of porosity (of the materials used) on the thermal properties was also investigated. The laser flash method and a pushrod dilatometer were used.

Jan 1, 2011

By D. Leppert

Mr. Garrett brings up several interesting points with respect to the proposed API specification for "nontreated bentonite." However, although not explicitly stated, these specifications are being written based strictly on bentonites from the Wyoming/South Dakota area. Other sodium bentonites may be suitable for use as drill mud but will be unacceptable since the specifications are designed for Wyoming bentonites. Regardless of the API's intent that its specifications are intended only as guidelines, they are generally adhered to on an international basis and, for practical purposes, might as well be chiseled in stone. Estes (1986) notes that the quality of bentonite available from Wyoming producers has steadily declined since the early 1960's. The plastic viscosity: yield point (PV:YP) ratio was included in the current API 13A specification primarily to prevent excessive polymer treatment of lower quality bentonites to make drill mud. However, with development of polymers designed to control YP, this specification cannot ensure that only high-quality bentonites are used for drill mud. Nor will the new specifications for untreated bentonites. Other sodium bentonites are available. Bentonite produced in southeast Oregon demonstrates superior performance characteristics without addition of polymer or other chemicals. However, the exceptionally high purity of these deposits leads to a relatively high YP:PV ratio since the naturally high YP probably results from the higher purity and smaller particle size of this bentonite (Rath, 1986 and personal communication). These bentonites typically have a smectite component exceeding 90% (Rath, 1985), compared with 70% to 75% smectite for typical Wyoming bentonites, as determined by X¬ray diffraction and tests for colloid content. As evident from the accompanying table, the untreated Oregon bentonite has excellent rheological properties, though different from Wyoming bentonites due to the high purity. Additionally, this bentonite reacts well with polymers typically used in the oil industry, making it eminently suitable for use in a low-solids mud system. The extremely low grit content, less that 0.5% on a 75 mm (200-mesh) wet sieve, greatly exceeds the standards set for Wyoming bentonite. Optimum rheological properties are obtained at a higher moisture content than Wyoming bentonites. At 10% moisture, API 13A maximum, the clay is overdried, again reflecting the high smectite content. In summary, the specifications proposed by the API Task Group will ensure that only Wyoming producers can supply "nontreated" bentonite to the oilfield since specifications are

Jan 1, 1989

By Daniel Su

Approximately 90% of the primary roof bolts used in CONSOL?s Pittsburgh seam coal mines is 2-piece, 8-foot long, 7/8? (or ¾?), high-strength, resin assisted, mechanical shell tensioned bolt. The remaining 10% is the 2-piece, 8-foot long, 7/8? combination bolt, which employs 4 feet of fast resin to anchor the deformed rebar at the top of the hole. In either system, a 1-3/8? hole is required to accommodate the mechanical shell and the coupler. The cheaper torque-tension rebar system, which is typically fully-grouted with 2-speed resin and which typically provides low bolt tension, is not used in CONSOL?s Pittsburgh seam mines. Rather, it is used in CONSOL?s Central Appalachia mines, where the roof rocks have CMRR rating of 50 or higher. Fully-grouted headed rebars, on the other hand, are used in CONSOL?s room-and-pillar mines. The selection of tensioned versus non-tensioned, fully-grouted bolts for coal mine primary roof support has been debated for the past thirty years. Many researches have been conducted to understand the theoretical bases behind the two systems. This paper describes CONSOL?s experience of using a new fully-grouted, mechanical shell tensioned bolt in the Pittsburgh seam with the development of low insertion force resin.

Jan 1, 2007

By Xiaodong Ma, Marek Pawlik

Introduction Guar gum is a natural nonionic polysaccharide. Guaran, the functional polysaccharide in guar gum is a chain of (1?4)-linked ß-D-mannopyranose units with a-D-galactopyranose units connected to the mannose backbone through (1?6) glycosidic linkages. The poly-mannose chain is randomly substituted with galactose units at a mannose-to-galactose ratio of 1.8-1.0 [1]. Cheng et al. reported that the molecular weight of natural guar gum is 1.935 • 106 [2]. Robinson et al. found that the molecular weights of five grades of commercial guar gums ranged from 4.4 • 105 to 16.5 • 105 [3]. Guar gum is frequently used as a depressant of naturally hydrophobic gangue minerals (e.g. talc) in the flotation of PGM-bearing ores, and according to Harris et al. a wide variety of modified guar gums are available for this application [4]. The Canadian potash industry utilizes natural guar gum as a blinder of water-insoluble slimes in the flotation of potash (sylvinite) ores, a process that is carried out in a saturated KCl/NaCl brine. The role of the polysaccharide is to prevent a primary amine collector from adsorbing onto these unwanted fine minerals. Hydrophobic interactions between basal cleavage planes and the polymer appear to be involved in guar gum adsorption on talc [5,6]. Liu and Laskowski stressed the importance of metal impurities on mineral surfaces that can serve as the active sites for polysaccharide adsorption [7]. This postulate was consistent with the later observation that, in addition to hydrogen bonding, the adsorption of guar gum onto talc was strongly dependent on the surface concentration of magnesium sites [8,9]. In this case the adsorption process was visualized as metal-polysaccharide complexation facilitated by the cis-configuration of the hydroxyl groups of mannose monomers. Hydrogen bonding and chemical interactions with metal sites were also suggested by Rath and Subramanian in their studies on guar gum adsorption on biotite mica [10]. In a recent study, Wang et al. demonstrated that hydrogen bonding is the main driving force behind guar gum adsorption onto talc [11]. Their data also show that the adsorption density of guar gum on alumina is about five times lower than the adsorption density on talc. Pawlik and Laskowski reported that the amount of guar gum adsorbed on illite was independent of ionic strength over a wide range of salt concentrations [12]. The adsorption density of the polysaccharide on illite did not measurably change with ionic strength from that of distilled water to about 50%-saturated KCl/NaCl potash brine (~3N KCl/NaCl). However, guar gum adsorption on dolomite dramatically decreased over the same range of ionic strengths, and no reliable explanation of that phenomenon was proposed [12]. The water structure-breaking or structure-making capabilities of background ions are usually ignored when discussing adsorption mechanisms of polymers. The concept of “structure breakers” and “structure makers” was first introduced by Gurney, and Frank and Wen who postulated that each ion is surrounded by three distinct regions of water structure [13,14]. In the first layer, water molecules are tightly bound to the ion. The second region extends farther away from the ion and is referred to as the region of structure breaking. Only at larger distances, where the ionic field is weak, water molecules form the “normal” ice-like structure. It is also now recognized that the first layer can be further divided into the primary and secondary hydration shells. Small, strongly hydrated ions reinforce the “normal” structure of water and the region of structure breaking disappears. In contrast, large less-hydrated ions disturb the ice-like structure and generate an extensive region of structure breaking. Experimentally, these two effects can readily be distinguished through viscosity measurements. Increasing concentrations of structure-breaking ions result in a decrease of the viscosity of aqueous solutions. On the other hand, increasing amounts of structure-makers significantly reduce the viscosity of water. Alkali metal cations form a sequence known as the Hofmeister series. The Hofmeister series - Cs+, K+, Na+, Li+ - orders the cations from the least hydrated to the most hydrated. Based on literature viscosity data for aqueous

Jan 1, 2005

By Larry Rayburn

In the spring of 1999, construction commenced on the new Steelers Football Stadium in downtown Pittsburgh, Pennsylvania. Richard Goettle, Inc. (RGI) was the successful bidder to install the specified augercast piles for the foundation package. Description - Pittsburgh Steelers Stadium The new stadium will house the Pittsburgh Steelers Professional Football Team. It is widely believed that if a team is provided with a modern playing facility, that a winning season will ensue (Not always the case). The new stadium location is on the north side of Pittsburgh on the Ohio River, and just downstream of the confluence of the Monongahela and Allegheny Rivers. The site is west of existing Three Rivers Stadium. The Three Rivers Stadium was built during the late sixties and housed both the Pirates Baseball and Steelers Football Teams. The Public Auditorium Authority elected to replace this outdated stadium with two new stadiums, one for each professional team. The landmark stadium was imploded in February of 2001.

Jan 1, 2001

By Matthew S. Sanchez, Richard J. Lee, Matthew D. Zock, Drew R. Van Orden, Yumi Kamiya, Edward B. Ilgren

In many developing countries, asbestos is still used for friction products, insulation, and asbestoscement products. However, there is very limited modern data evaluating the airborne concentrations of asbestos fibers in operating asbestos plants. We have conducted an Industrial Hygiene survey, using state of the art PCM and TEM analysis, of a Bolivian asbestos cement plant that uses crocidolite during the production of roofing shingles and water tanks. The study is the first to use modern analytical measurements in an uncontrolled asbestos environment. Thus, this study offers insight into the historical airborne exposures at asbestos plants operating before modern dust control measures were introduced or airborne fiber levels regulated. The results suggest that fiber concentrations are far in excess of those for which current models would predict the onset of asbestos disease and mesothelioma. Significantly, the plant and community do not have an elevated incidence of asbestos disease or mesothelioma. Airborne fiber levels during comminution and fiber sizing ranged from 100 to as much as 1,000 f/cc. Fiber levels in the mixing, forming and finishing areas ranged from 0.5 to 9 f/cc. Based on the number of overloaded samples and estimates of their concentration, historical estimates of exposure may be underestimated by an order of magnitude. Also, an excellent correlation (1:1) between the PCM and TEM fiber concentrations (for fibers _0.25 um diameter) were obtained, raising questions about the conventional wisdom that the PCM systematically undercounts fibers. The results of this study further indicate that current models may overestimate the risk of asbestos disease and mesothelioma.

Jan 1, 2012

By Chris Jobes, Alan Mayton, N. Kumar Kittusamy, Dean Ambrose

NIOSH researchers conducted a study to compare seat designs on underground coal mine haulage vehicles. The objective of the study was to support prior findings that NIOSH-designed seats, which incorporated ergonomic design features (e.g., viscoelastic foam padding and low-back support), are improved designs. Based on measured levels of vehicle jarring/jolting and perceived discomfort, researchers evaluated four different designs - two in-use and two NIOSH-developed, ergonomic designs. Researchers collected data using a short questionnaire, a linear, visual analog scale, and accelerometers with a data recorder. Results showed that vehicle operators favored the NIOSH seats with added adjustability, low-back support, and improved seat padding over the existing seats. In addition, the measurements indicated all NIOSH seats performed better than the existing seat, under the no-load (worse of two) conditions, in reducing peak acceleration, crest factor, and RMS acceleration. The authors summarize the data collected and operator preferences for seat designs and different foam padding arrangements.

A simple and cost effective technique to increase fragmentation and burden velocities without making major modification to the overall blast design is with ALTERNATE VELOCITY LOADING OR BOOSTERING OF ANFO. The technique requires the placement of a cartridge or slug of explosive, having higher density and detonation velocity than ANFO, every few feet in an ANFO column. The greater the difference in density and detonation velocity of the Alternate Velocity Load to ANFO, the more pronounced are the results. Emulsions were selected as the Alternate Velocity test explosives because they detonate closer to ideal conditions than most other commercial explosives.

Jan 1, 1989

By S. A. H Tyrrell, R. Rotzinger

"Taseko Mines Limited recommenced operation of the Gibraltar copper-molybdenum mine in 2004 and embarked on series of development projects to modernize the mine and increase throughput capacity. The Gibraltar Development Plan 3 (GDP3) project included a second stand-alone copper-molybdenum concentrator, a stand-alone molybdenum separation plant and associated services. Ausenco was contracted to commence the detailed design in 2Q2011, commissioning commenced in 4Q2012 and first ore was processed in 1Q2013. This paper discusses the design, implementation and commissioning of the GDP3 Concentrator.INTRODUCTION The Gibraltar Mine (Gibraltar) property is located in the Cariboo Region of south central British Columbia, approximately 360 kilometers northeast of Vancouver. The site is accessed via an 18 kilometer paved road from the town of McLeese Lake, which is located on the province’s main north-south highway between the cities of Williams Lake and Quesnel. Gibraltar was originally developed by Placer Development and commenced production in 1972. Gibraltar was acquired, while on care and maintenance, by Taseko Mines Limited (Taseko) in 1999 during a period of unusually low metal prices. Taseko recommenced operations at Gibraltar in 2004, and embarked on series of development projects to modernize the mine and increase throughput capacity. The 1972 Gibraltar process flowsheet incorporated two-stage crushing followed by rod and ball milling and flotation. In 2008 Gibraltar completed their first development stage that included the installation of a SAG mill, converting the existing rod mills to ball mills and adding additional flotation capacity. Gibraltar continued development with the installation of an in-pit primary crusher, expansion of the bulk regrind circuit, expansion of the cleaner flotation circuit, replacement of the tailings pumping system and replacement of the concentrate filters and dryer."

Jan 1, 2014

By M. J. King, A. Weissenberger, W. G. Davenport

Keywords: Pyrometallurgy, sulphuric acid, sulphur dioxide The raw material for sulphuric acid manufacture is clean SO2 gas. It comes from (i) burning molten by-product sulphur; (ii) roasting or smelting metal sulphide concentrates, and (iii) decomposing contaminated organic chemical process sulphuric acid catalyst. Efficient gas cleaning is required for metallurgical and contaminated acid decomposition gases, especially the former. Sulphuric acid is made from SO2 gas by (i) oxidizing the SO2(g) to SO3(g) in contact with supported liquid-phase catalyst then (ii) reacting the resulting SO3(g) with the water component of 98.5 mass% H2SO4, 1.5 mass% H2O acid. This paper discusses the reasons for these process steps and indicates how acidmaking can be controlled and optimized. Special emphasis is placed on SO2(g) oxidation efficiency and how it is influenced by feed gas composition, feed gas temperature, catalyst composition, catalyst bed pressure, number of catalyst beds, and double versus single contact acidmaking. In addition, a review of various other treatment methods for SO2-bearing gases is provided. A brief description of each process is included along with commentary on their technical and economic applicability for use at metallurgical facilities.

Jan 1, 2006

By A. McLean, M. Barati

In this paper, examples are presented of pyrometallurgical research and associated teaching activities during the past century within the Department of Metallurgical Engineering, now the Department of Materials Science and Engineering, at the University of Toronto. Throughout these years, pyrometallurgical research has been characterized by recognition of the importance of the interdependence of measurements and models as well as the development and application of sensors, for the generation, validation and practical implementation of new knowledge. The important role played in the delivery of lectures and participation in joint research by Adjunct Professors with strong backgrounds in the pyrometallurgical industry is described. Projects conducted in close collaboration with the industrial sector and opportunities for students to obtain practical experience working as teams on a "round-the clock" shift basis within an industrial pilot plant environment are outlined. These activities, together with the involvement of students in poster competitions and the presentation of papers at society conferences and technical meetings, are still vital elements in the development of pyrometallurgists equipped with the appropriate professional skills for subsequent employment within academia, government laboratories or the industrial sector.

Jan 1, 2015

By Arel B. McMahan

The U.S. Bureau of Mines investigated 21 mines, prospects, and mineralized sites in and adjacent to a 38,713-acre portion of the 255,058-acre Kingston Range Wilderness Study Area in 1983. The study area is 35 miles north of Baker, CA in the Mojave Desert. Mineral deposits in and adjacent to the study area are in altered carbonate rocks intruded by diabase sills near monzonite porphyry contacts. Monzonite porphyry forms the core of the Kingston Range and underlies about 70 percent of the study area. Sedimentary carbonate rocks are exposed in bands on the north and east boundaries and as isolated roof pendants in the southeastern portion of the study area.

Jan 1, 1986

By Hermes Vilchéz

El presente texto describe los beneficios de la apertura de los circuitos de flotación como alternativa de mejora en la performance metalúrgica de las concentradoras. El trabajo se efectuó en la empresa minera Los Quenuales, Unidad Iscaycruz (Lima), modificándose los circuitos cerrados a los abiertos y encontrándose los siguientes beneficios: el incremento del tonelaje de tratamiento sin aumentar equipos en los circuitos de flotación, la mejora en la recuperación y el grado de concentrados.

Sep 9, 2007

By V. Gall, J. Rudolf

The Virginia Department of Rail and Public Transportation and the Metropolitan Washington Airports Authority are undertaking the extension of Washington Metropolitan Area Transit Authority’s Metrorail service to Washington Dulles International Airport and beyond to Route 772 in Loudoun County, Virginia. The roughly 37 kilometers long, double track alignment involves two 700 meters long single track, soft ground NATM tunnels at Tysons Corner, two 3.3 kilometers long single track rock TBM tunnels at Dulles Airport and one 25-meter deep station at the airport to be constructed by NATM in sedimentary rock. The design-build project is being implemented in a Public-Private-Partnership. A joint venture of Bechtel and Washington Group International has concluded the preliminary engineering and construction is scheduled to start in late 2007.

Jan 1, 2007

GENTLEMEN, lt is with much pleasure I meet you tonight at this the second meeting of the Australasian Institute of Mining Engineers, held in Western Australia, and I sincerely thank you for the honour you have conferred upon me in electing me as your President. I greatly appreciate the distinction, and will endeavour to fulfil the duties of the office to the best of my ability, and hope to prove a worthy successor to those gentlemen who have held the position before me. On behalf of the local members of the Institute, I extend a hearty welcome to the members from the other States of the Commonwealth, who have come so far to attend this meeting, and also to the non-members whom we have invited this evening. We are especially pleased to have Mr. Gregory, our Minister of Mines and Railways, and the Government and School of Mines officials with us; and I take this opportunity to thank the Premier, Mr. Gregory, and the Government officials for the assistance given us, and for doing so much to make the visit of our members from the other States so pleasant and instructive. I have also to thank the Mayor and Councillors of Kalgoorlie for the courtesy and hospitality given to our members, which is much appreciated.I assume you want me to follow the time-honoured custom of giving a Presidential address...

Jan 1, 1909

By Göran Bäckblom

The Swedish mining companies LKAB and Boliden, the equipment supplier Atlas Copco, the general contractor NCC and the specialist company Reflex joined forces in 2005 to advance the field of rock technology for the purpose of mining and underground construction. The creation of the company Rock Tech Centre is part of the strategy developed by the Swedish mining industry to strengthen co-operation with industry, academia and society. This paper outlines the current R&D strategies developed for the industry in general, discusses what focus areas are selected and provides some details on the current RTC project portfolio, especially faster and better drifting.

May 1, 2006