Search Documents

By M. Fan, M. Mankosa, G. Luttrell

"Column and other non-conventional flotation approaches continue to provide benefits where conventional flotation processes have exhibited limited success. This is particularly evident with respect to flotation of ultrafine and coarse particles. Advancements in air sparging technology have provided the ability to produce finer bubbles than previously possible. The generation of finer bubbles coupled with the froth washing capabilities of a flotation column has demonstrated improvements in ultrafine particle recovery while simultaneously producing a high-grade float product. On the other side of the spectrum, the use of these sparging technologies while applying flotation fundamentals to a fluidized-bed reactor has increased the maximum floatable particle size up to and in excess of 3 mm. Benefits of higher recoveries and reduced reagent consumption have resulted from the use of these technologies. An additional benefit includes a reduction in plant grinding requirements. As such, this paper describes the application of Cavitation-Tube sparger technology and fluidized-bed flotation (HydroFloat). A review of data from industrial and pilot-scale applications is also provided.INTRODUCTIONConventional (mechanical) froth flotation is considered the workhorse of the minerals processing industry. This low-cost process makes it possible to selectively recover minerals by exploiting the difference in surface characteristics (e.g., wettability) of the valuable component and the waste material. Unfortunately, the upper particle size limit for flotation rarely exceeds 0.600 mm, and is typically maintained at less than 0.300 mm for most industrial applications. For many commercial base metal plants, the particle size range for optimum recovery is typically between 0.01 and 0.1 mm (Lynch et al., 1981). This finding is not novel. In fact, the effect of particle size on flotation recovery was studied as early as 1931 by Gaudin et al. who showed that coarse (+0.250 mm) and extremely fine particles (-0.010 mm) are more difficult to recover than particles of an intermediate size. The loss of recovery is due to inherent limitations associated with the flotation process, including bubble-particle adhesion and collision, detachment, buoyancy, and transport."

Jan 1, 2010

In 1960, the Secretary of the Interior, acting under the provisions of Public Law 454, 80th Congress, appointed a Lignite Advisory Committee to aid in programming research on coal (lignite) of the north-central area. The chairman of this committee is the Secretary of the Interior or his delegated representative, and in all meetings held during 1960 and 1961, the Director of the Bureau of Mines, Marling J. Ankeny, has presided. The members of this committee were R. W. Rovelstad, President, Baukol-Noonan, Inc., Noonan, N. Dak. W. E. Keller, Vice President, Northwest Division, Truax-Traer Coal Co., Minneapolis, Minn. A. M. Cooley, Professor of Chemical Engineering, University of North Dakota, Grand Forks; N. Dak.

Jan 1, 1963

By Sean Dessureault

Information technology (IT) initiatives in the past have tended to be sold on their ability to maximize resource output and return on capital by using assets more effectively and efficiently. Many IT projects fail, not delivering return on their investment. This is known in the IT industry as the ?productivity paradox,? where increasing investments in IT do not result in comparable increases in productivity. Experiences and studies of most business sectors reveal that this paradox is rooted in the false assumption that more IT spending automatically results in financial benefit, whereas the true source of benefits is in how effectively IT is used. Most business sectors have accepted that the reengineering of processes is required to gain the full benefits promised of IT. A mining operation has organizational processes similar to most business sectors but unique operational processes. The lessons of changing business practice in more common business processes such as inventory control and customer-supplier relationships can be adequately transposed into a mine. The unique operational processes in mines, in turn require unique redesign efforts. Several enabling information technology opportunities have recently become available, such as more integrated mine production management systems and tactical manger training simulators. This paper reviews the latest IT products and ou lines the processes and kinds of change that will be required in order to benefit from these new investment options.

May 1, 2002

By T. Tholana, P. N. Neingo

"Mining companies globally are currently facing severe economic and financial challenges. In addition to global challenges, the South African mining industry has to face other operational challenges that are unique to the country and which threaten the survival and competitiveness of the industry. Profit margins are being squeezed by rising costs and decreasing commodity prices, while labour productivity is greatly affected by intermittent labour unrest. This paper analyses how the South African gold mining industry has performed pre-, during, and post the global financial crisis of 2008. The competitiveness of the industry in terms of labour productivity and industry cost curve position is analysed for the period 2006–2013 to assess the impacts of both the global financial crisis and labour unrest. An analysis of the South African gold mining industry is presented at company as well as mine level. Productivity measure in this paper is limited to labour productivity, in line with limited reporting on productivity. All the data analysed was obtained from the public domain. IntroductionSouth Africa dominated the world as the number one gold producer until 2009 when China took that position, and today South Africa ranks fifth after China, Australia, Russia, and the USA. According to Statistics South Africa (2009), South Africa still had about 30 years of production in the gold sector, a forecast that fluctuates based on the day’s modifying factors. Although South Africa has a comparative advantage in terms of minerals endowment, there are challenges faced by the mining industry that hinder translation of the comparative advantage into a competitive advantage. The industry continually seeks to address these challenges to remain competitive in global markets while addressing national and community needs.Neingo and Cawood (2014) argued that stakeholders in mining are continually concerned with mine management’s ability to translate use inputs effectively into quality outputs. They further suggested close monitoring of effective utilization of people, materials, and money to obtain maximum production of commodities under given conditions. Productivity is measured in various ways, including unit cost, output per employee, and output per unit capital equipment"

Jan 1, 2016

By R. H. Bedford, F. T. Johnson

"In California the history of tin mining began in Riverside County in 1853, with the discovery of the Temescal deposit. This deposit remained the only one with a production record until recent small shipments were made from Kern and San Bernardino Counties.According to the California State Division of Mines, Temescal's total output has been about 125 tons of tin, all of which was produced in 1891 and 1892. It was idle from 1892 to 1928.An extensive but unsuccessful development campaign carried on in 1928 and 1929 by the American Tin Corp. produced only half a ton of the metal, and the property again was idle until 1943, when an attempt to resume operations proved unsuccessful. After 1929 no production is recorded from California until 1944 end 1945, when small shipments of sorted ore from Kern County returned about 2 tons of tin and 1-1/3 tons was recovered from sorted ore and concentrates from San Bernardino County. The total output of tin from California has been less than 150 tons, and less than 4 percent of this was produced in the last 50 years, in spite of numerous attempts during that period to promote tin mines,So marked a scarcity of a metal essential in war makes any occurrence interesting. When some prospects were reported to the Bureau of Mines in July 1942, in a new field 10 miles east of Gorman, they were at once examined and the preliminary exploration by the owners closely followed. Eventually one was explored by bulldozing end diamond drilling as a joint project by the Bureau of Mines and the Geological Survey.To supplement this joint project, the authors undertook independently a general survey of tin in California - a survey designed to check reported occurrences and to bring their status up to date. In this work, the 37 places described in the text and spotted on the accompanying map, (fig. 1) were visited end sampled. Although traces of tin were found in many pieces, nothing that suggested a tin mine was found anywhere, and it is difficult to base much hope for appreciable future tin production upon anything found thus far in California."

Apr 1, 1946

The 107th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Wednesday, 11 August, 2004. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, past-presidents, our members and other guests, among them the following: Ralph Bagirathi, Executive Member, African Mining Association Rudi Rudolph, President, Association of Mine Managers of South Africa Andrew Whibley, President, Association of Mine Resident Engineers of South Africa Dr Con Fauconnier, President, Chamber of Mines of South Africa Nxolisi Diliza, Chief Executive Officer, Chamber of Mines of South Africa

Jan 1, 2004

By H. P. LeVan

The aced for reliable reserves of the essential element, manganese, has been a continuing concern of the Federal Government for more than three decades. Because of the increasing vulnerability of outside sources of supply efforts have been intensified to find a means for beneficiating United States domestic deposits. The deposits of most interest would of necessity be near, or have access to, suitable transportation to processing plants. The Georgia manganiferous iron deposits represent some 10 million tons4 of ore readily available to southern iron and steel industries, if a manganese recovery process capable of functioning in the presence of large quantities of iron can be developed. In addition, a successful method for beneficiating the Georgia ore could produce a significant quantity of high-grade iron concentrate. The Differential sulfatization process developed 47 the Bureau of Mines5 seemed to be well suited for this application, particularly because it results in low concentrations of iron in the leach liquors with relatively complete extractions of manganese. In this process, manganese in the presence of iron is preferentially reacted with sulfur dioxide at elevated temperatures and subsequently extracted with water.

Jan 1, 1962

By Thomas Weyand, Thomas Claridge, Dale Nickels

"This paper addresses the initial results of a project to evaluate the suitability of copper mining tailings as raw material for the production of structural products using PMET’s patented technology. Preliminary testing indicated that high performance structural products were possible using these materials. A demonstration scale project produced approximately 1,500 bricks in various colors. These products fall under under ASTM C- 73 and were found to present properties suitable for severe weather applications. Although the products in this project were of typical brick dimensions, other products are possible, for example concrete block substitutes or pavers. These products from the PMET process are commercially known as Brixx. This paper will provide operational details of the production process, mineralogy and mechanical properties of the products.INTRODUCTIONPMET has developed process technology that can convert various siliceous waste materials into competent structural products. This technology is the subject of US patent # 6,068,803. In general, the process consists of mixing lime, water and the major feed stock, pressing to form a “green” shape, and curing the product in an autoclave for 6 hours with saturated steam at ~200oC. The curing process forms Tobermorite, which acts as a crystalline binder. Freeport-McMoRan approached PMET to see whether mine tailings from the Sierrita mine, containing significant amounts of clay, might be a suitable feed material for the production of structural products. “Brixx” is the commercial term used to describe the resultant structural product formed in the test work. This paper is a preliminary evaluation of a technology that is being considered by Freeport-McMoRan. This report is not an endorsement by Freeport-McMoRan of the process or products, nor is it a commitment to use this technology."

Jan 1, 2008

By AMY F. JENNINGS

TO give a concise history of the Woman's Auxiliary of the A. I. M. E. is a difficult task and much interesting information must needs be omitted. The organization has grown and evolved so much from its early simple beginning that it seems best to adopt the technique of some of our modern novelists and begin with the latest development. As the headquarters of the A. I. M. E. is in New York, it follows that the Woman's Auxiliary to the A. I. M. E. necessarily has also its central office and government there. The affairs of the organization are administered by a duly-elected president and five vice- presidents, a treasurer, recording secretary, and corresponding secretary and a board of directors, the personnel of which includes each chairman of a section or an elected or nominated representative who is able to attend the monthly meetings of the board and correspond with the section for which she acts, and the chairmen of the five standing national committees, i. e. Educational Fund, Library, Emergency, Membership and Hospitality. The chairmen of these committees are all responsible to the president and board of directors and their activities must be indorsed with their approval.

Jan 1, 1929

By Franklin M. Grynkewicz

The subject of bearing pile performance installed by vibratory hammers has been a matter of increasing study and continued controversy. A recent case study from a major bridge replacement project is discussed which provides encouraging data on the use of vibratory pile hammers as a primary means of pile installation and also presents the problems associated with its general acceptance. The bridge project case study foundations consisted of HP 14 x 89 pile sections, designed to develop capacity primarily in friction. Preliminary tip elevations were determined by traditional static analyses. Production pile installation was performed using an IHC S-70 Hydro-Hammer. Driving criteria and final production pile tip elevations were determined after preliminary indicator pile drive tests and static load test results at bridge pier cofferdam locations. Based on impact driven production pile performance, the Contractor wished to investigate vibratory driven piles as a means to accelerate construction schedule. Dynamic pile testing procedures were used as the primary measurement tool and test results were compared to the production pile drive records and prior static load tests. Field testing consisted of driving and monitoring with the PDA impact driven piles to the design tip elevation. Three vibratory driven piles were installed to the same tip elevation and immediately subjected to impact driving and dynamic testing to compare dynamic pile resistance. The results indicated that the site soil conditions were favorable for vibratory pile hammer installation. Recommendations and procedures for proceeding with vibratory hammer pile installation were presented to the Owner. These procedures included quality control in conformance with latest AASHTO recommendations. The Owner, in spite of the site specific data base and QA/QC procedures, would not accept vibratory pile hammer installation, due to the absence of precedence. It is concluded that for vibratory methods to become accepted a rational method of analysis, design and field QA/QC procedures requires development. In addition, the engineering community and Owners/Agencies must be more open to alternate methods of foundation construction. The continued development of dynamic methods of monitoring vibratory pile installation is considered to be key to the general acceptance of this installation procedure.

Jan 1, 1991

By Erik M. Westerberg

The Soilex Pile combines a slender shaft, for quick and easy installation, with an enlarged pile toe, for high capacity. The key component is the Expander Body, which is inflated by injecting cement grout when in position. The latest development in the Soilex Pile System results in a reduction of the total cost of Soilex Piles, in many cases values that are competitive with pre­cast concrete piles and displacement piles. Soilex Piles can now be installed on top of a bearing soil layer, instead of 3 to 4 m into that soil as previously required, further minimising the ground disturbance. Soilex Piles achieve high capacity in relatively loose soils, with ultimate loads typically between 1000 and 2000 kN in a sand with CPT qc = 5 to 10 MPa or SPT N= 10 to 20. It is possible to pre-load and proof-load all piles with dynamic testing up to 2000 kN or using built-in jacks, thereby verifying the capacity. The vibratory installation method, which is extremely quick and causes very little soil disturbance and noise, is exemplified by two case histories.

Jan 1, 2000

By A. Nuric, S. Nuric, L. Kricak, M. Negovanovic, S. Mitrovic

"SynopsisRotary drilling with rolling tricone bits is the most widely used method for drilling large-diameter blast-holes in large surface mining operations. This drilling method is applicable to a wide range of soft to hard rock materials. This paper presents a fuzzy model for predicting the penetration rate of tricone rotary blast-hole drilling. The model is based on data obtained during the drilling of blastholes in rocks with various uniaxial compressive strengths in the Veliki Krivelj open pit mine, Bor, Serbia. The model was developed using the fuzzy logic toolbox of MATLAB with the Mamdani inference system. The fuzzy model was tested with 23% of the total dataset. The results obtained show the high reliability of predicting the penetration rates. Although there are possible limitations in applying the model to other open pit mines because of differences in rock properties, the prediction methodology applied in this paper can be used in many other predictions of the penetration rates.IntroductionAccording to Tamrock, rotary blast-hole drill operations depend on four important elements:•,Torque in the drill string drive sufficient to turn the bit in any strata encountered•,A high bit loading capability (pulldown force) sufficient for optimum penetration•,An air volume sufficient to remove chips generated during the drilling and to provide cool air to the drill bit bearings•,The selection of the proper type of bit for the material being drilled (Tamrock, 1984).The effects of rock mass parameters on the choice of the type of tricone bits were investigated by Kricak (1997)."

Jan 1, 2015

By R. P. Mohring

The South African Coal Industry had its beginnings in the Eastern Cape in 1859 when coal was mined to satisfy the fledgling settlements in the Eastern Cape. The growth in the industry was relatively slow up to the early 1970s when, firstly, the export business was expanded coupled with a major increase in the quantity of coal converted to liquid fuels and utilized for power generation. To meet this increased demand the industry developed many new operations employing the latest mining technology and systems. Coal production in South Africa reached 204 million tons in 1996 and revenue from exports reached R8 billion making it the second-largest foreign exchange earner after gold. In his address Rick P. Mohring describes the role coal plays in the international energy scene and outlines South Africa?s position as a producer and consumer of coal, and the challenges facing the industry. A wide range of steam-coals are produced to satisfy both the local market (power generation, coal conversion and the metallurgical industry) and the export steam-coal market. South Africa is in a unique position regarding the export market as it is still a relatively low-cost producer and is geographically well-placed to play in both the European and Far East markets. There are, however, a number of challenges facing the industry. To retain our competitiveness in the international market, ways of minimizing the cost pressures caused by high-cost inflation, increased environmental protection obligations and a decreasing quality resource base need to be sought. Locally the coal mining industry has a major role to play in Eskom?s goal of reducing the real cost of electricity by 15% in the next three years. Safety and health, productivity and the adaptation of the latest technology are issues being addressed by the industry to maintain its dominant position within the South African economy.

Jan 1, 1997

By R. W. Courtney

The objective of this study is to make a critical evaluation of the magnitude and extent of electrostatic hazards in typical U.S. mining operations and to assess the adequacy of techniques, materials, and equipment for detecting and minimizing these hazards. This was accomplished with an incident/accident survey, mine visits, literature search, and engineering analysis. It was concluded that it would be desirable to (1) utilize ground fault interrupters to minimize stray current from electrical utilities, (2) decrease the current and electrostatic sensitivity of electric detonators used in areas with a high incidence of lightning strikes or troublesome stray currents, (3) institute quality control and test standards for blasting material and protective devices, (4) establish an electrostatic monitoring program for loading ANFO in plastic lined holes, and (5) establish a risk criteria for operator exposure in mines.

Jan 1, 1982

By María Eugenia Castro, Silvia Galasso, Jorge Duca, Claudia Osuna, Ernesto Esparza

"We present a procedure for treatment of non-active solutions equivalent to the solutions obtained from dissolution of ionic exchange resins used in purification of a nuclear reactor primary cooling system containing Co, Ni, Cs and its isotropic varieties as main radioactivity source. Finally it is immobilized into a ferritic matrix by calcination which avoids its future leaching into environment.In order to achieve the objective of this treatment, a bivalent and a trivalent iron salt is added to the solution. Then, either a base or an acid is added, depending on the initial pH of the treated solution, with a Cs precipitating additive in order to reduce Co and Cs by precipitation, flocculation and adsorption. Controlling the amount of precipitating reactives it is possible to modify the activity/volume rate becoming a medium into a low radioactivity waste.The leaching test result applied over the ferritic sample is lower than the minimum limit established by law. Therefore, it can be kept safely in a interim storage."

Jan 1, 2008

A study was made of zircon powders bonded with phosphoric acid or aluminium orthophosphate. The influence of strength of solution of the phosphatic binders on the modulus of rupture over a temperature range was investigated. Physical properties of three grades of zircon powder bonded with phosphatic binders were studied at various temperatures. Examination of x-ray diffraction data indicated that phosphates ofzirconia are preferentially formed to phosphates of silica. However, zircon in the presence of excess phosphoric acid also forms phosphates of silica upon heating.Resistance to attack by slags from blast and open hearth furnaces was determined on phosphate-bonded zircon mortars in a cup test with industrially made ladle bricks. Zircon powders bonded with phosphates proved to have high P.C.E. values. The first satisfactory results of a plant trial with phosphate-bonded zircon mortar, used in a steel ladle, are now being assessed in larger scale industrial tests prior to accepting the mortar as a steel plant refractory.

Jan 1, 1972

By F. Habashi

Siberia, a vast country rich in mineral resources and a large number of different ethnic groups. To the east of Lake Baikal is Buryatia with capital Ulan Ude. The Buryat are closely related to the Mongolians. Ulan Ude is connected to Ulaan Baatar (Ulan Bator) the capital of Mongolia by train – a 26 hours trip. Getting a visa to Russia is not a simple case. Visits to metallurgical research laboratories, Lake Baikal, and historical museums are enriching experience.

Jan 1, 2006

By D. F. Cooper, J. G. Paterson, K. H. Pang

"Effective control of metallurgy by manual adjustment of cell levels is common flotation practice. With an on-stream XRF analyzer interfaced to a process control computer it is possible to program the computer to carry out this function automatically. This paper describes the development and implementation of closed loop control of the concentrate and tailing grades at the Clarabelle Mill of the International Nickel Company of Canada, Limited, The XRF analyzer was used as the sensor, cell level as the control and the computer as the controller.IntroductionThe International Nickel Company of Canada, Limited recently brought on-stream Clarabelle Mill having a rated capacity of 35,000 tons per day. The plant was required to increase milling capacity in the Sudbury area by 9,000 tons per day and to improve milling efficiencies by replacing the obsolete crushing and grinding equipment at the Copper Cliff Mill. This represents the fourth mill built since 1959 and incorporates the latest thinking in a continuing evolution of instrumentation and control concepts. Table 1 illustrates control progress at Inco since 1959.In 1967 Frood-Stobie Mill came on-stream incorporating a central control room, an on-stream analyzer, a data gathering computer, and a significant change in instrumentation from direct-contacted pneumatic to miniature electronic. The computer successfully controls the analyzer but has very limited process control capability. Based on this experience a process control computer system was installed at Clarabelle Mill with the objective of carrying out extensive supervisory control and a limited amount of direct digital control."

Jan 1, 1973

By James E. Hill

Tremendous improvements in mining technology have been witnessed during the past 100 years. For example, before 1860 all blastholes were drilled manually and blasting was done with low-energy black-powder. During the 1860's both the pneumatic rock drill and high-energy dynamite were introduced, ushering in an era of mining mechanization that has steadily progressed since that time. Today, with the rapid implementation of the latest advances in communication science, mining technology is moving into a new era that goes beyond mechanization as such. Transistors, transducers, scanners, telemetry, and the like, all terms largely derived from the new communication sciences, add up to what is popularly know as automation-the communication of machine with machine. Automation is now playing an important role in selected parts of the mining process, such as hoisting, hydraulic roof supports, and underground surface locomotive haulage and belt conveyor systems. But this year marked the first attempt to auto-mate the total mining process with the commencement of production at the British National Coal Boards Bevercotes mine. If this full-scale experiment proves successful, it could lead towards other fully automated mines in both Britain and other parts of the world. This decade, there-fore, could be considered the one that provided the foundation for the mines of the future.

Jan 1, 1966

By Michael Young, Josh Rubenstein, Michael Cooper, Tom Shouldice, Dan Curry

"Xstrata Nickel Australasia’s Cosmos plant in Western Australia is currently implementing a debottlenecking project to increase nickel output while maintaining metallurgical performance and a low unit cost for production. Mineralogical analyses indicated that the processing bottlenecks could be removed by simply reconfiguring portions of the circuit as well as adding capacity with technical advancements – notably an IsaMill™, Jameson Cell, Wemco® SmartCell™ and Larox Filter.The Wemco® SmartCell™, which is particularly suited for coarse mineral flotation, and Jameson Cell, which is particularly well suited for fast floating and fine minerals, combine as rougher scalpers to complete the main stream portion of the flotation circuit. Addition of the two new cells meet the required flotation capacity to handle the forecast increase in nickel feed grade and tonnage.The addition of an IsaMill™ for regrinding allows the SAG mill to produce a coarser primary product, thus enabling increased throughput. The advantages offered by the IsaMill™ include operation in open circuit (internal classification), an inert grinding environment (ceramic media) for better downstream flotation (“clean” new surfaces), compact footprint (easy to retrofit into existing plant) and energy efficiency. With the new rougher capacity addition, the remaining original plant cells were reconfigured to suit the new regrind mill and cleaning requirements. The existing 24 m2 Larox pressure filter was replaced with a larger 32 m2 unit to dewater the increased concentrate output.The paper describes the upgrade at the Cosmos concentrator with particular emphasis on the mineralogical data and metallurgical benefits associated with the changes.INTRODUCTIONThe Cosmos concentrator is located 680 km northeast of Perth in Western Australia. The deposit’s development and operations were started in 1999 by Jubilee Mines NL, Cosmos’ previous owner, with the first production of nickel concentrate in April 2000. The Cosmos concentrator treats a komatiite hosted high grade nickel sulphide ore, with sulphides being predominantly pentlandite and pyrrhotite with lesser amounts of pyrite and chalcopyrite."

Jan 1, 2010