Search Documents

By Ivo André

Sorption of copper ions from aqueous solutions by dried biomass of the aquatic plant Potamogeton luscens was studied at laboratory scale. The aquatic plant was collected in water resources in Brazil, washed, dried at 60°C and ground in a bladed mixer. Sorption experiments were conducted in agitated flasks and in a packed bed column. Maximum copper removal was obtained between pH 5.0 and 6.6 when copper was present in the ionic form Cu'. Sorption followed the Langmuir isotherm with saturation attained at 35 mg/g. Free energy of sorption was found, to be of the order of -25 kJ/mol. Sorption kinetics data were better described by a second order reaction and rate constants were calculated in 0.030 1/(min.mg) for - 4.0 mm particles and 0.081 1/(min.mg) for - 0.59 mm particles. Removal of metal ions in a packed bed column showed that Potamogeton luscens biomass can be used in several sorption/dessorption cycles. After sorbent saturation, copper ions can be recovered from the loaded biomass by elution-with H2SO4, solution. Main mechanism responsible for heavy metal uptake was found to be ion exchange. Results are discussed in terms of the surface properties of the biomaterial, solution chemistry of copper ions and thermodynamics parameters.

Jan 1, 1995

By P. N. Anyalebechi

The effects of Si (0.19-0.52 wI. %), Fe (0.20 wI. %-0.44 wI. %), and Cr (0-0.10 wI.%) on the response of ingots of aluminum alloy 3004 solidified at different rates (O.IO°C/s to 30°C/s), to homogenization heat treatment have been investigated. Response to homogenization was determined by quantifying the following microstructural parameters: (i) amount of Mn retained in solid solution; (ii) types, relative amounts, sizes, size distributions, shapes, and chemical compositions of second phases; (iii) extent of the alpha-transformation (i.e., AI6(Fe,Mn) --7 (XAI12( Fe,MnhSi) reaction; (iv) dispersoid formation; and (v) alleviation of dendritic microsegregation. Of the three alloying elements investigated, Si had the greatest effect on the response of aluminum alloy 3004 to heat treatment. Increase in Si content, fineness of cast microstructure, and homogenization temperature facilitated alpha-transformation reaction, dissolution of Mg2Si, loss of Mn supersaturation, and formation of AldFe,Mn)3Si and Mg2Si dispersoids.

Jan 1, 2008

By P Ridgeway, D Xie, M A. Somerville, S Jahanshahi, H Rogers, J G. Mathieson, Y Pan, N Haque, P Zulli, T E. Norgate, L Lu, A Deev

In 2006 the Australian steel industry and CSIRO initiated an R&D program to reduce the industry’s net greenhouse emission by at least 50%. Given that most of the CO2 emissions in steel production occur during the reduction of iron ore to hot metal through use of coal and coke, a key focus of this program has been to substitute these with renewable carbon (charcoal) sourced from sustainable sources such as plantations of biomass species. Another key component of the program has been to recover the waste heat from molten slags and produce a by-product that could be substituted for Portland cement. This paper provides an overview of the low-emission Integrated Steelmaking Process, progress made over the past seven years and the program’s future direction which includes proposed demonstrations of the technologies developed including large scale piloting and full scale plant trials.

Jan 1, 2014

By R. J. Kuczynski

The U.S. Bureau of Mines Reno Research Center operated a batch pilot plant to demonstrate high-temperature cyanide leaching for recovering platinum group metals (PGM) from automobile catalysts. Approximately 1,600 kg of used pellet, monolith, and metal support catalyst containing 1,680 g (54 tr oz) of PGM were processed. Forty-five-kilogram batches of used catalyst were leached with sodium cyanide solution at 160° C for 1 h under basic conditions in a countercurrent processing sequence to dissolve the PGM. Extractions from the used pellet catalyst ranged from 94 to 95 pct for Pd, 95 to 97 pct for Pt, and 64 to 81 pct for Rh. Extractions from the used monolith catalyst ranged from 7B to BB pct for Pd, 75 to 90 pct for Pt, and 43 to 71 pct for Rh. Heating the pregnant leach solutions to 275' C for 4 h destroyed the PGM-cyanide complexes, resulting in over 99.7 pct of the PGM precipitating from solution. The PGM precipitate was predominantly a powder metallic concentrate, typically analyzing greater than 50 pct PGM. Heating destroyed cyanide to less than 0.2 mg/L. Both the pellet and monolith residues were evaluated for disposal using the EPA Toxicity Characteristic Leaching Procedure.

Jan 1, 1995

By Evgenii Pavlov, Ivan Tronin, Viktor Timofeev, Vladimir Kislov, Sergei Bogovalov

"Modeling of the magnetohydrodynamical (MHD) and thermodynamical processes during the industrial scale Direct Chill (DC) casting of aluminum slabs is performed using a combination of ANSYS/CFX and ANSYS/EMAG software. The electromagnetic field is modeled through ANSYS/EMAG, while hydrodynamic and thermodynamic processes are modeled through ANSYS/CFX. Both packages were modified in order to calculate MHD flows in the liquid pool that forms during aluminum DC casting, and they were unified into a software combination that provides simultaneous simulation of all the above processes. The simulation shows that the electromagnetic stirring of the molten aluminum changes the shape of the solidification front (solid-liquid interface) very dramatically, namely it becomes significantly flatter. This effect should improve the internal structure of aluminum DC slabs and allows us to increase the casting velocity.IntroductionProduction of Aluminum alloys with high mechanical properties and structural uniformity is one of the main goals of industry. The preferred production method of aluminum alloys in most modern plants is Direct Chill (hereafter DC) casting because it offers high productivity and commercial success. One important limitation of this technology is the development of centerline shrinkage in slabs larger than about 1 meter. The improvement of the internal structure of long DC cast slabs can be achieved by electromagnetic stirring (hereafter ES) of the liquid metal above the solidification front. This intensifies heat transport in the zone close to the solidification front and suppresses shrinkage formation."

Jan 1, 2013

By Denise Crocce Romano Espinosa, Andrea Moura Bemardes, Jorge Alberto Soares Tenorio, Daniella Cardoso Buzzi, Tatiana Scarazzato

"In copper plating processes, a fraction of raw materials are incorporated to the final products, while other portions are discarded as effluents. In this study, the application of electrodialysis (a membrane treatment process) was studied for treatment of wastewaters from cyanide-free strike baths, in order to reuse the components of this bath: copper and HEDP. The synthetic solutions studied consider 1 % of ion concentration of the bath used in this process, simulating the rinsing waters to be discarded. The electrodialysis allowed a percentage extraction up to 73% of copper ions and 72% of HEDP from the effluent. Complexes formation between the acid and copper indicates the possibility of recovery of components in the same compartment, obtaining a concentrated solution of these substances that can be reinserted in the process, for compensating drag-out losses. A diluted solution is also obtained, that can be reused as water in rinsing tanks.IntroductionIn metal finishing industries, contaminants in wastewater and the type of treatment required are determined according to the type of operation [l]. Generally, electroplating industries employ conventional wastewater treatments, e.g. oxidation of cyanide and chemical precipitation. This stage promotes reactions with soluble compounds to produce an insoluble precipitate, removed by physical separation. The sludge is dried by press-type filters [2].In this manufacturing sector, part of the raw materials are discarded as hazardous waste. The cost of discarded compounds and the treatment and disposal of waste may compromise profit margins. In addition, water consumption per unit of production stimulates the development of methods able to recover and reuse the largest possible amount of water [3].In some plating processes, cyanide-based substances are used as complexing agents and as raw materials in form of metal salts [4]. However, the toxicity associated with cyanide has been promoting research for the development of new raw materials in plating processes.A study conducted in Brazil [4] evaluated the modification of a commercial cyanide-free bath for processes of copper coating on Zamak. In the performed study, a new alkaline copper bath was formulated using l,hydroxyethane-1,1-diphosphonic acid (HEDP), an organic compound known for forming stable complexes with metal ions.As results of the study, the operational conditions and the formulation of a bath to obtain adherent, uniform and bright layers were established (Table I) [4]."

Jan 1, 2014

By J. B. Winter

The present Inspiration Consolidated Copper Company Smelter/Acid Plant complex located near Miami, Arizona, was designed and built specifically to conform to the ambient air quality standards imposed by the Federal Clean Air Act of 1971. The present plant replaced a facility which had been in operation since 1915. The electric furnace, siphon converters and acid plant complex were commissioned in May, 1974 (1). At that time, the Plant was considered to be one of the most extensively monitored and instrumented facilities of its kind in the world. Several control areas were located in close proximity to the controlled process, in addition to so-called central control rooms in the Smelter and Acid Plant. The control rooms were staffed with officials below the foreman level. Instrumentation consisted of conventional analog devices, except for a computer used in monitoring ambient air environmental conditions and limited use of programmable logic controllers. The harsh service conditions prevalent in the plant rendered a significant portion of the instrumentation unreliable and, in many cases, inoperable. Failure of the facility to obtain the total sulfur collection for which it was designed was, in part, due to serious inadequacies in control system logic and sulfur recovery averaged 79% in the early years. After careful study of the smelting process, engineering hardware and high labor cost inherent in the organizational structure, management made a judgement decision to convert to centralized control of the process with high level supervision 24 hours per day. A distributed digital control system with supervisory arid data acquisition/information reporting computers was selected to satisfy the requirement of central control. Operations are now controlled and coordinated from a primary control room in the Smelter and a satellite control area in the Acid Plant.

Jan 1, 1983

By Hong Yong Sohn, Miguel Olivas-Martinez, Zhixue Yuan

A novel flash ironmaking process that directly reduces iron oxide concentrate particles by gas is under development. The goal of this work was to study the possibility of reoxidation of iron particles in various gas mixtures. As the product iron cools down in the lower part of the flash reactor, conditions may become favorable for reoxidation because of equilibrium and high reactivity of iron particles. The effects of temperature (823 – 973 K) and H2O partial pressure (40 – 100 pct., Ptotal = 86.1 kPa) on the reoxidation rate were examined. The pressure dependence was first order with respect to water vapor, and the activation energy was 146 kJ/mol. A complete rate equation that adequately represents the experimental data was developed. For oxidation in O2-N2 mixtures, the effects of temperature (673 – 873 K) and O2 partial pressure (5 – 21 pct., Ptotal = 86.1 kPa) were determined. Reoxidation in pure CO2 was also investigated at 873 – 1073 K for comparison.

Jan 1, 2014

By P. S. Arthur

The ISASMELT? process is a submerged lance smelting technology operating in smelters in Australia, the USA, Belgium, India, Germany, Malaysia and China. Further plants are under construction in Peru and Zambia. Following the invention of the Sirosmelt lance technology Mount Isa Mines recognised the commercial potential in the novel top blown bath smelting process and embarked on a development program that has lasted more than 25 years. After successful operation of pilot plants and demonstration plants producing copper and lead, Mount Isa Mines decided to license the technology to external companies. Since the purchase of Mount Isa Mines by Xstrata in 2003, Xstrata Technology has assumed responsibility for transferring the technology to ISASMELT? licensees. In the 15 years since the first commercial furnaces started operation plants have been constructed (or are under construction) with a combined annual smelting capacity of more than six million tonnes of concentrates or secondary raw materials. Process development continues on the commercial scale plants at Mount Isa and elsewhere. Many of the improvements implemented by plant operators have been passed on to, and adopted by, other licensees. Exchange of ideas and technical improvements occurs through ad hoc visits to fellow licensee sites and through regular licensee workshops arranged by Xstrata Technology. This paper updates the reader on the status of various ISASMELT? plants either operating or under construction. It highlights the important role that the technology provider?s operational experience plays in ensuring that new smelting plants ramp up quickly to nameplate capacity.

Jan 1, 2006

By Zhihe Dou, Yan Li, Qiuyue Zhao, Guozhi Lv, Yan Liu, Hongliang Zhao

"Abstract: How to reduce carbon dioxide emissions has become a vexing problem, meanwhile, there exist high energy consumption and low efficiency problems in the existing CO2 capture and storage technologies. For CO2 comprehensive Utilization, this paper researches a new technology of absorbing the CO2 emission with high alkaline calcium or high alkaline wastewater sludge mineralization of calcium and invent a core device for multi-level jet carbonation. The industrial test has been carried out in China Xinyu slag Engineering Co., Ltd. The wastewater flow is 150m3/h in the pilot scale. The prepared calcium carbonate has a whiteness greater than 90%, particle size less than 150nm. The mineralization of aluminum exhaust with waste carbide indicates that the CO2 absorption rate is greater than 99.0%, CO2 concentration in the exhaust gas is lower than 0.08%, the purity of mineralized calcium carbonate is greater than 99.0% and particle size is less than 100 nm.InstructionAccording to the statistic data from IEA (2009), the carbon dioxide discharge from fossil fuel consumption in China has exceeded it in the US by the year of 2007, China, has become the largest emitter of carbon dioxide all over the world. Meanwhile, the economic scale is still on an increasing trend in the next 50-100 years, leading to a continuous increment in carbon dioxide discharge. According to the international energy agency forecasts, the energy-relative CO2 discharge in China will rise to 11,615 million tons, 91.3% higher than it in 2007. In the year of 2012, the CO2 gross discharge has reached 10,000 million tons, obviously higher than the predicted value. It is a tremendous task to reduce the emission. Non-ferrous metals industry is one of the largest emitters of carbon dioxide among the industrial circle, the whole industry might discharge a huge amount of carbon dioxide (over 600 million tons), in which the electrolytic aluminum industry is the largest energy consuming industry and CO2 emitter. At present, the CO2 discharge has focused by the whole world due to the environmental problems it causes; meanwhile, supplement of new carbon source is needed due to the exhausting oil and coal resources, so that various countries in the world are attaching importance of the recycle and purification of CO2. Many countries are studying on the cyclic utilization of carbon dioxide. Gas CO2 is mainly applied in chemical, pharmaceutical raw materials, beverage filling agent, refrigerant, inert medium, solvents, pressure source, the welding protective gas, antioxidant and fire extinguishing agent, etc. Solid CO2 is mainly applied in penicillin production, fish, cream, ice cream and other food storage and transportation at low temperature, etc. nowadays, such methods as absorption method, membrane separation, adsorption, etc. are widely used to recycle CO2, with such problems as high investment cost and technical constraints etc."

Jan 1, 2014

By S. A. Davis

In July of 1996, the Kroll process began production again at TIMET's Henderson, NV, manufacturing facility. This, after being shut down for several years due to low market demand for titanium. Faced with limited pond capacity and increasing costs for water and wastewater disposal and storage; process changes were made to recycle water used to wash Kroll titanium sponge back into the sponge leaching process. This idea was revisited from 1992-93, when three consecutive attempts to recycle water for this application were unsuccessful due to early pump failure. Since it was uncertain why previous attempts failed, a complete understanding of the existing system was first sought. This included reviewing piping and flow diagrams; taking field measurements for all the piping, valves, and fittings; analyzing the wastewater composition; and modeling the fluid dynamics and control of the system. The fluid dynamics of the system were modeled by breaking the piping network up into nodes and applying the Bernoulli equation to each segment. The fluid flowrate control valves were modeled for this purpose also and the models were used to help specify the required processing equipment and control ranges and tolerances. Once the project was completed, an operating procedure was prepared for operation, startup, and shutdown of the washer water recycle system.

Jan 1, 1999

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu, Xueduan Liu

Bio-hydrometallurgy technology was applied for the extraction of copper from the raw ores of Chambishi Mine in Zambia. A copper extraction of 93.29% was obtained for small scale column bioleaching within 63 days, while a copper extraction of 89.05% was achieved for large scale column bioleaching in 90 days, thus confirming the amenability of the raw ores for effective extraction via bioleaching. The bacteria were cultured in a 6-stage enlarge cultivation. The bacterial cultures with cell concentration of more than 1×108 cells/mL were added into a spray pond of sulfuric acid to be applied in the dump leaching, and a copper extraction of about 50% was achieved within 2 months. The production report revealed that the copper extraction increased by approximate 20%, and the acid consumption was reduced to around 35% as a consequence of adding the bacteria. The industrial demonstration of the bio-hydrometallurgy technique is now well established in Zambia, and further applications of bio-hydrometallurgy in both Zambia and Congo are currently in progress.

Jan 1, 2015

By H. K. Fouad, L. A. Guirguis

The starting mill strip solution· for this study· is an ammonium uranyl tricarbonate solution of pH 8.2 containing 20g uranium/liter, after a DEPA/TOPO extraction process from sulfuric acid leaching liquor. To the first portion of the concentrated acidified strip solution, hydrofuoric acid is added at 95°C in reduced condition to obtain uranium tetrafluoride. The second portion of the uranyl carbonate strip is subjected to a precipitation step by admixing 0.3 volume of non-solvent precipitating agent such as acetone per volume of uranium. ·Uranium oxide (U30 8) is obtained from this precipitate by calcination for half an hour at 800°C in air. The third portion of the strip solution is neutralized to a pH 6.5 with sulfuric acid to precipitate iron and other contaminants. The solution is further acidified to a pH 1.85 with continuous air bubbling to remove CO2, followed by H2Ch precipitation at pH 3.5 to obtain uranyl peroxide. The latter is reduced by stannous chloride to obtain uranium trioxide dihydrate UO3. 2H20. Identifications, characterization· and purity of these products are carried out by complete chemical analyses, Scanning electron microscope study, tap density determination, X-ray diffraction and infrared spectroscopic investigations. The achieved results agreed well with that of the published data for these nuclear grade purity products.

Jan 1, 2000

By Mehdi Asadi, Heinz Palkowski

"In recent years, the increased demand for advanced high-strength steels (AHSS) mainly had been driven by the need of the automotive industry to reduce weight and to improve safety. Beside good ductility and high strength, those steels have a high bake hardening (BH) effect, giving additional contribution to the strength of structural parts, subjected to the paint baking process. In this paper we concentrate results gained for hot rolled dual phase (DP) steels.For the simulation of changing process conditions within the final hot rolling the specimens were hot deformed using different schedules of temperatures and reductions, selected according to the non-recrystallization temperature (TnRX). It was possible to refine the DP steel structure by control-ling the deformation temperature and the amount of strain below TnRX during the thermo-mechanical controlled processing (TMCP). This structure refinement resulted in an improvement of the strength and BH behaviour. A wide spectrum of mechanical properties could be obtained depending on the different hot deformation schedules. The best strength and BH levels were recorded for the deformation below TnRX at the highest amount of strain.IntroductionDP steels are characterized by a good formability, high strength and a good compromise between strength and ductility [1]. Moreover, the DP steels exhibit a continuous yielding behaviour, low yield point and a high strain-hardening coefficient [2]. Furthermore, the DP steels often show a large potential for bake hardening (BH). BH refers to the increase in yield strength as a result of the paint baking treatment of the shaped auto-body parts. The primary mechanism that causes the additional strengthening is the immobilization of dislocations by the segregation of interstitial atoms, known as classical static strain aging [3]. The increase of strength thus achieved allows a further reduction of sheet thickness and improves the crash safety and the dent resistance. The BH of special steel qualities is technically used in DP, where e.g. the increase in strength is realized in the final heat treatment [4]. Previous own investigations [5-6] stated that the BH effect of DP is much stronger than that one for conventional BH steels."

Jan 1, 2012

By H. Kamarudin

The behaviour of cassiterite-sulphosuccinamate flotation system was examined in the light of zeta potentials measured by micro-electrophoresis method. It was observed that sulphosuccinamate substantially affects the zeta potentials of cassiterite, lowering its i.e.p. to pH 2.5 and indicating a specific adsorption and/or chemical interaction. The optimum concentration for flotation, as seen in micro-flotation tests, was found to be associated with the most effective lowering of the zeta potentials, the optimum pH being 3.0. The effect of cations in the pulp was examined for the presence of ferrous, ferric, aluminium and lead ions. The ions ferric and aluminium were observed to create an intense effect of increasing the potentials to positive side, possibly due to adsorption of cation hydroxy complexes, as indicated by their respective species distribution diagrams.

Jan 1, 1994

By H. Ikeda

The new Onahama N0.3 tankhouse was put into operation early in 1973. This new tankhouse, which has a capacity of 90,000 metric ton cathode per year, is distinct in many important respects from conventional tankhouses. The major objectives in design were to simplify the construction and ope- ration for reduction of the costs for labor, interest and depreciation and also to reduce the copper inventory in the tankhouse by the use of conti- nuously-cast anodes. As a result, the investment cost was decreased by approximately 30% and the inventory cost by approximately 600, while the production per unit area of the tankhouse was increased by 80 - 100% as compared with the existing conventional-type tankhouses at Onahama. By abolition of cell inspection and maximum mechanization of materials handling the labor cost was decreased by as much as 80%. On the other hand, the new system has some disadvantages, such as increase in anode scrap ratio and increased cost of anode casting. The No.3 tankhouse system is, however, still at its starting point, while conventional methods have been continuously improved over the past years of operation. It is expected that the innovational ideas behind this system will serve as bases for a more efficient electrolytic refining system in future.

Jan 1, 1976

By Chan. C. L., Zehr. R., M. M. Chen, J. Mazumder

"Two three-dimensional models of a surface tension gradient driven flow during laser surface heating are developed. The first model is based on a perturbation solution. The basic solution corresponds to the stationary axisynwnetric case and perturbation is based on a small scanning velocity. The advantage of seeking a perturbation solution, as it turns out, is that the three-dimensional flow is modeled by two sets of two-dimensional equations which are presumably much more tractable than the original three-dimensional equations. Numerical solutions are obtained and discussed. The second model is a full three-dimensional numerical solution of the Navier-Stokes equations, using a point-by-point partially vectorized iteration scheme. Surface shape is also determined in a self-consistent manner. The effect of the presence of convection on pool geometry, cooling rate and solute redistribution is presented and discussed.IntroductionThe existence of fluid flow and convection and their effects were first reported in the fifties (1,2). The role of convection in controlling pool geometry such as pool shape, undercut and ripples, and defects such as variable penetration, porosity and lack of fusion and weld properties such as weld homogeneity and bead formation is studied by a number of researchers and is reviewed by the authors in a recent paper (3).Recently, surface tension gradient driven flow has been identified as one of the forces responsible for convection within the molten pool (4,5). It is postulated that surface tension gradient driven flow is responsible for the surface ripple formation in the weld pool (6-8). Oreper, et al. (9) developed a two-dimensional convection model. Buoyancy, electromagnetic and surface tension gradient forces were considered. The formulation was based on a specified pool profile. It was found that the surface tension gradient is the dominant force in most cases. However, the solid-liquid interface is not known a priori. In fact, the solid-liquid interface, i.e. the pool shape, is a piece of information that the model should be able to predict. A two-dimensional transient self-consistent (i.e. the solid-liquid interface is solved as part of the solution] model for laser surface melted pool was first developed by Chan, Mazumder, and Chen (3)). This model predicted a non-uniform cooling rate, hence non-uniform microstructure. Depending on the Prandtl number (i.e. material) and surface tension number, the shape of the molten region as well as the cooling rate changes. It was also predicted that the recirculating velocity is of one or two order of magnitude higher than that of the scanning velocity. This model provides the detail of the flow field and heat transfer on a plane perpendicular to the scanning direction. However, the front-to-back motion and its effect on heat transfer also play important roles in the physical process, especially for the fact that the recirculating velocity is so much higher than the scanning velocity. Such a motion cannot be obtained from two-dimensional models."

Jan 1, 1986

By Xu-ling Chen, Qian Li, Yong-bin Yang, Zhao Jing, Tao Jiang, Guang-hui Li

"It is generally known that alkali metals are harmful to blast furnace production resulting in aggravating RDI of sinters, abnormal expansion of pellets, deteriorating blast furnace lining, etc. Sinters regarded as dominating burden of blast furnace are determined as the main source of alkali metals. In this study, the removal behavior of potassium and sodium oxides by pre-reduction sintering during the sintering process was studied. The removal ratio ofK20 and Na20 was greatly influenced by coke powder content, carbon species, coke powder adding ways, additive and so on. Under the conditions of carbon rate 12% and 5% dosage of CO supplied in the sintering process, the corresponding removal ratio ofK20, Na20 was 69.00% and 32.79%, and metallization ratio could reach 4.65%. This technology provided a novel process for reducing the content of alkali metals in sinters and dramatically improving the quality of blast furnace burden.IntroductionSinter is the main iron-bearing charge of blast furnace for iron-making in China, making up about 80% of the total burden; therefore, its quality has a significant influence on the quality of pig iron and blast furnace operation. Research and practice of numerous years prove that potassium and sodium coming from ores are brought into blast furnace and upgraded, which is one of the essential reasons that lead to blast furnace nodulation and influences its strength. Currently, effective flow sheet to remove potassium and sodium is weak magnetic separation-intensive magnetic separation-flotation [l], while iron ore concentrate is still ofhigh levels of potassium and sodium. As sintering process is also not effective to remove potassium and sodium, blast furnace in China is of high alkali burden, e.g. it reaches 5.6-6.2kg/tFe in Baotou iron making plant, which is greater than international tolerated level of2.55kgltFe [l]."

Jan 1, 2013

By Joerg Hammerschmidt, Marcus Runkel, Andreas Wirtz, Kent Pope

"Fluidized bed reactor systems in the minerals industry have been progressively developed and widely implemented over a period of more than sixty years for a multitude of process applications. Their versatility is manifested in calcining, roasting and combustion treatment of minerals including solid fuels. Experiences from metallurgical processes have expanded to new applications in the oil shale processing, biomass combustion and renewable energy sector. This paper focuses on the most important aspects of fluidized bed technology for a variety of Outotec processes. Energy recovery is a major topic for all applications and will be addressed, as well as environmental aspects, particularly regarding the off-gas treatment. Outotec is one of the pioneers of roasting and the fluidized bed process including gas cleaning and sulphuric acid production where applicable. Process development is strongly supported by significant investment in R&D, thus enabling process adaptation and scale-up to meet specific customer/market requirements.Introduction to Fluidized Bed TechnologyThe early days of fluidized bed technology were characterized by the use of bubbling fluidized bed reactors (BFB). This technology was popular for roasting zinc and copper ores. The introduction of circulating fluidized bed technology led to increased plant capacities and improved process control for the traditional processes. Furthermore, the technology has been applied in many other industries, including the renewable energy industry, which will be part of this design and process comparison. The paper starts out with the fundamentals on particle fluidization as the main common design parameter, leading to the importance of heat recovery and offgas treatment.In fluidized reactor systems, the particle concentrations can reach several hundred kilograms per cubic meter of fluidization gas. This high solid concentration leads to large surface areas and enables direct contact of gas molecules with particle surface molecules. Excellent conditions for enhanced heat and mass transfer thus provide nearly ""ideal"" heat exchange conditions and better reaction kinetics. The bubbling bed exhibits a better heat transfer coefficient within the bed in comparison to the circulating fluidized bed (CFB). The different conditions of gas velocities and solid concentrations allowing the classification of fluidization reaction regimes are shown in the Reh diagram in Figure 1."

Jan 1, 2014

By Glenn C. Miller

Cyanide is the most common lixiviant for extraction of precious metals, and its efficient use in open pit mines has contributed to the increase in world production of gold during the previous two decades. With this expansion of precious metals mining using cyanide, public concerns have developed in response to the inherent public perception of cyanide as a tox-in as well as a series of environmental problems that are directly or indirectly related to cyanide use in open pit mining. Some of these have technical or regulatory solutions, while others will require additional investigation before they can be resolved. The following discussion will summarize some of the public concerns regarding the use of cyanide in precious metals mining. The issue of cyanide use in large scale precious mining is controversial, and recent banning of cyanide use in open pit mines in Montana, or complete banning of cyanide in Hungary has reflected those international concerns. The underlying basis for some of the bans (e.g. Montana) reflect a general concern of the environmental impacts of mining, rather than specific issues related to risk of cyanide use. The human safety record for cyanide use, particularly in the developed countries is good, and cyanide is clearly the most efficient lixiviant for precious metals. Indeed, the relatively short lifetime for cyanide in the environment renders it one of the less problematic chemicals used for extraction of gold from ore. Mercury amalgamation or use of bromide as a lixiviant are certainly much more problematic. What, then, is the basis f~r the international concern about precious metals mines that use cyanide. Ifuse of cyanide for gold recovery is to continue, what additional infom1ation needs to be developed that will allow a better management of the risks of cyanide? Which of the concerns are directly related to cyanide, and which are indirect concerns that more related to effects of open pit mining. Under what conditions should use of cyanide be discouraged? DUl::ing June of 2000 the United Nations Environmental Program conducted a two-day workshop on cyanide use in mining that was attended by persons from the mining industry, regulators and environmental community. Support and attendance at this workshop reflected concerns by all three groups on further restrictions for cyanide use and the emerging potential for guidelines for better management of the catastrophic release of cyanide-containing mining waste. The following discussion is meant to focus-on those risks and explore the basis for an often negative reaction to precious metals mining using cyanide. It is presented in the format of a statement, followed by a discussion. While admittedly provocative, the statements are meant to express the concerns? of the public regarding cyanide and the mining industry.

Jan 1, 1998