Search Documents

By K. O. Fagerlund

Theoretically and experimentally determined copper matte settling rate in iron silicate slag has been discussed. Separation and settling rate measurements of sand, homogenised slag and 25%Cu concentrate, 63%Cu industrial, and 71%Cu synthetic copper mattes were carried out by mixing crushed slag and matte samples with silica sand in an alumina crucible and melting at 1300-1350°C. Two different types of slag compositions were employed, with Fe/SiO2-ratio 1.4 and 1.7. The separation rate was followed by taking samples from the .melt. As expected, the settling rate of copper matte in fayalite slag depended on the slag composition, where the increasing silica decreased the matte settling rate. Microanalysis of solidified slags showed that the rate of separation of low grade matte was low compared with high grade matte and the presence of a very small size fraction of matte droplets in slag remained unsettled in stagnant fluid. The production of sulfur dioxide gas inside the molten bath was found to be possible up to a certain iron sulfide content in the matte. Also, copper matte settling rates in industrial furnaces have been discussed.

Jan 1, 1999

By C. Anderson

Most applications of copper metallurgy are geared towards primary production. However, as recycling of materials is a growing industry, one future facility will rely on copper metallurgy as a means of processing precious metals. This paper will discuss the derivation of the proposed copper pyrometallurgical and electrometallurgical unit operations to be utilized in industrial recycling of secondary precious metals.

Jan 1, 1999

By A. J. Rigby

Current practices employing porous plugs to inject nitrogen into molten copper during primary smelting are described. Nitrogen stirring increases heat transfer to the bath, eliminates temperature stratifications, and improves efficiency during the steps of desulfurization and deoxidation. The opportunity to use porous plugs as the means to introduce reducing gases to deoxidize copper is also discussed. Previously reported laboratory results using porous plugs, which point to very high utilization efficiencies of hydrogen when used as the reducing gas, are again reviewed. Advances in the design of the porous plug, and the introduction of a system enabling external replacement of plugs is also discussed.

Jan 1, 1999

By S. D. Prosser

The earliest record of slag in the world was the discovery of the remains of a copper blast furnace in Southern Israel, which has been carbon dated at 3500BC, nearly 6,000 years ago. Slag in Australia is a much more recent phenonenum with the first iron blast furnace commencing operations in 1848. The early days of metal smelting in Australia were marked with many company failures due to a variety of reasons. This paper traces the progress of metal and slag production from those early days up to the present times

Jan 1, 1994

By Iain B. Mackenzie

In 1997, a thin layer of Microtherm Microporous Insulation was used to replace fireclay brick behind the magnesia/chrome working lining in #5 refining furnace at BHP?s San Manuel AZ smelter. A 23°C reduction in shell temperature was obtained, together with a large increase in the working capacity of the vessel. There was no sign of metal penetration as a result of the increased insulation. Following these highly favorable results, BHP have introduced this product into all of their refining furnaces.

Jan 1, 1999

By Zviad Kovziridze

It is stated that the specific character of SPHTS specimens of TiCx consists in crystal lattice strength reflecting the condition of synthesis in ?burning wave?. The use of roentgenographic and other methods of analysis allow to estimate the effect of the conditions of synthesis causing the carbon sablattice defect on the grinding intensity of TiCx -phases. The study of the kinetics of vibratory grinding of TiCx -phases in ethanol and benzene medium allows to establish high grinding intensity of the phases close to stoichiometry and the possibility of producing high dispersion powders (Ssp 4.5-6 m2/g).

Jan 1, 2006

By W. F. Miao

Nanocrystalline mixtures of Nd2Fe14B and a-Fe have been synthesized by mechanical milling and heat treatment. The samples exhibit isotropic behavior, with significant remanence enhancement associated with exchange coupling across the interfaces of hard and soft magnetic phases. Measurements of the effect of heat treatment on structure and magnetic behavior demonstrate the important influence of grain size on magnetic properties. The effect of alloy additions to increase the saturation magnetization of the soft phase and the magnetocrystalline anisotropy of the hard phase has also been investigated.

Jan 1, 1997

By Chunlin Chen

Published data on thermodynamics of a number of minor elements (As, Sb, Bi, Pb, Zn, Se, Te, Cr, Sn) in liquid copper, matte and slag have been reviewed, assessed and used in development of thermodynamic solution models of melts. The behavior of antimony in alloys, mattes and slags is used as an example to illustrate the approach taken in assessment of published data and validation of the developed models with respect to the activity of Sb in condensed phases as well as the effects of matte grade, slag chemistry, temperature etc on the equilibrium distribution of Sb between melts and the gas phase. Results obtained from a comparison of different smelting processes with the modeled multi-phase equilibrium are presented and discussed. The predicted effects of slag chemistry and matte grade on the deportment of other minor elements during smelting of copper mattes will be presented and discussed.

Jan 1, 2006

By D. J. Sellmyer

This paper is Intended to review recent developments in the application of rare earth-transition metal alloys as high density, rewritable data-storage media. First generation magneto-optic media are based on amorphous Tb-FeCo or GdTb-Fe alloys which are adequate but could use improvements In certain respects. A very difficult materials-design problem is encountered because of the following requirements: a sufficiently large Intrinsic uniaxial anisotropy, a Curie temperature in the range 100-300°C, a sufficiently high coercivity, a sufficiently high optical absorption, a high Kerr rotation, reflectivity and high carrier-to-noise ratio, a high storage density, a very fine and homogeneous nanostructure, long-term stability, and inexpensive production. , Fundamental issues such as the relationships between the nanostructure and perpendicular magnetic anisotropy, and electronic structure and Kerr rotation are discussed. Attempts to tailor the properties by rare-earth alloying and by preparing compositionally-modulated, nanostructured multilayers are outlined. Challenges and opportunities in competitive materials such as garnets, ferrites and Co/Pt multilayers are briefly discussed.

Jan 1, 1992

By K. D. Peaslee

The 150 metal producers in Missouri generate approximately 8,000 tons of spent refractories each year, most of which is landfilled. Spent refractory samples were characterized and recycling / reuse techniques developed for some of the largest waste streams. Products using recycled materials are compared with products made from virgin materials.

Jan 1, 2000

By L. Trincado

Mantoverde is a heap leach-SX-EW plant that was commissioned in December 1995 at a production rate of 42,130 ton of copper per year and 5.4 million ton of ore per year. Copper production has steadily been increased to 57,290 ton in 2002. Forecast copper production for 2003 is 60,000 ton for an ore treatment rate of 8.5 million ton. Several improvements in the heap leach process have been implemented. The main process improvements are related to the optimization of heap height, particle size, irrigation rate and leach cycle, in addition to a better heap drainage design and a solution management system. A first dump leach operation was started in 1999 at a production rate of 1,922 ton of copper. A second dump leach operation was started in early 2002 at a production rate of 2,805 ton of copper. Dump leach production will be increased over time to as much as 24,000 ton of copper. The main heap leach process improvements, as compared to the original plant design, as well as the main dump leach operating parameters are discussed in this paper.

Jan 1, 2003

By Ahmet Geveci

[Generally accepted formula related to sulfur slag-metal distribution ratio is given by the following equation: [ ] According to the above equation it can be deduced that sulfur distribution between slag and metal is governed mainly by metal composition (?s term), slag composition (slag basicity and in turn sulfide capacity), oxygen potential of the system (ao¬¬ term) and temperature(related to equilibrium constant, K). In this study, the results of ladle furnace operations conducted in Erdemir-Iron and Steel Works Co. (Turkey) in relation to sulfur removal, have been given. Typical ladle furnace slag analyses of 4937K quality steel have been presented. Activity coefficient of FetO,?FetO, have been calculated with the relation obtained fromthe literature. Activity calculations have been performed with the program written in Mathcad. The changes in activity of aFetO in the slag phase,, have also been studied in relation to the sulfur removal: The relation between % Decrease aFetO and %DeS (measured)have been investigated for 4937K runs and someother types of steel produced in the Erdemir Plant. Related to ladle operations %desulfurization defined as [(%Sinitial-%Sfinal)/S%initial]*100 values have been presented for different steel qualities.]

Jan 1, 2006

By Maria de Campos

The pre-reduction behaviour of chromite particles in methane-argon and methane-hydrogen gas mixtures was investigated between 1050°C and 1250°C. Loose bed of chromite particles were reacted in a vertical tube furnace under a pre-set gas mixture predetermined time intervals. Metallization results were obtained for the Cr and Fe components by chemically analyzing the reaction products. SEM-EDAX techniques and X-ray diffraction were employed to elucidate the reduction mechanism. It was found that higher reduction kinetics and higher Cr:Fe ratios in the metal phase would be achieved when hydrocarbon gas was used in comparison to classical carbothermic reduction at a given temperature. The reduction rate was generally bulk gas mass transfer controlled to the reaction site for initial stages which then was followed by ionic diffusion rate control. It is proposed that methane did not partake directly in the reduction but cracked, presenting the reaction site with hydrogen gas and atomic carbon, which was able to immediately react at the immediate area of reduction regeneration CO and H2 and thus maintaining a low partial pressure of oxygen at the reaction site.

Jan 1, 2006

By G. Achurra

The products of the smelting of copper concentrates in an El Teniente Converter (CT) are a high grade matte, analyzing 74-76% Cu; and a highly oxidized slag, typically containing 15-20% Fe3O4 and 4-10% Cu. The El Teniente Division of CODELCO¬CHILE has developed a slag reduction-cleaning process, that is practised in a tilting, horizontal furnace, to recover copper from these slags. The El Teniente slag cleaning process has been successfully implemented at the El Teniente Caletones smelter and various other smelters in Chile: Today, eight such slag cleaning furnaces, each with a capacity of 800-1000 tonnes/day, are in operation in Chile. This paper discusses basic laboratory research and industrial tests that led to substantial reductions in the slag cleaning cycle time and the specific consumption of fuel and reductants. Simultaneously, the slag cleaning off-gas quality was improved. Based on the experimental results, recommendations were made to improve the practice of the El Teniente slag cleaning process. The recommended modifications have been fully implemented at the Caletones smelter.

Jan 1, 1999

By Isabela Leao Amaral da Silva, Alice Barreto Bevitori, Frederico Muylaert Margem, Victor Bastos da Silva, Sergio Neves Monteiro, Artur Camposo Pereira

"The jute fiber is one of the most rigid natural lignocellulosic fibers, which has since the last decade been investigated as possible reinforcement for polymeric composites. In the present work, the tensile properties of DGEBA/TETA epoxy composites reinforced with jute fibers with different diameters were investigated. Composites with volume fractions up to 30% of continuous and aligned jute fibers were tensile tested at room temperature to evaluate the ultimate strength, elastic modulus and total strain. For each volume fraction, separated fibers with smaller larger diameters were tested. The results indicated that the tensile properties tend to improve with increasing volume fraction of the thinnest jute fibers. The role played by the fiber/matrix interaction was analyzed by scanning electron microscopy.IntroductionThe interest of this research is to develop composites with epoxy resin matrix reinforced with continuous and aligned jute fibers, for applications in various industries, including construction and automotive industry. Conflicts related to the use of non-renewable forms of energy are increasing the interest to enter the market to replace natural materials, synthetic materials synthetics have a higher power consumption in its manufacture [ 1-4].Therefore, applications of natural lignocellulosic fibers obtained from cellulose-based plants are receiving increased attention as an alternative to replace more environmentally correct nonrecyclable materials, energy intensive and glass fiber composites in [5-6]. The use of composites reinforced with natural fibers is a reflection of the concerns with environmental issues such as pollution caused by waste that is not biodegradable or cannot be incinerated and climate change due to C02 emissions associated with the processes of intensive energy and also motivates this work to develop self-sustaining, since natural fibers generate a source of income, especially in developing countries, where most originate, encouraging the cultivation of non-food agriculture [7-9]. Additionally, it is worth also remembering that these fibers come from renewable sources, in addition to being abundant, inexpensive and have a relevant set of mechanical properties [10]."

Jan 1, 2013

By Lucas Barbosa de Souza Martins, Frederico Muylaert Margem, Nathalia Carneiro Garcia Rosa, Sergio Neves Monteiro

"A natural banana fiber extracted from the plant pseudostem has shown values of density and mechanical strength with potential for uses in engineering applications such as automobile interior parts and floating components. Moreover, natural fibers can also be used as insulating materials in packaging and building panels. In this case some thermal properties are required. Therefore, the objective of this work was to evaluate the thermal behavior of the banana fiber by means of TGA, DTG and DSC analysis. The TGA curves revealed weight loss related to release of humidity and molecular structure decomposition. Peaks in the DTG curves indicated two intervals in temperature associated with different decomposition processes. The only endothermic DSC peak found was attributed to the lignocellulosic water of hydration being lost around 121°C.IntroductionIn recent times, environmental aspects related not only to pollution caused by non-degradable synthetic leftovers, specially polymeric wastes, but also to climate changes as a consequence of industrial activities, are motivating the use of natural materials. A particular case is fibrous composites, like the fiber grass composites. These synthetic materials, made from non-renewable polymers, are practically non-degradable and contribute to global warming by the CO2 emission associated with the energy required for the fabrication process. In spite of these environmental shortcomings, fiber materials are essential for the production of many items such as insulating chests, automobile cushion, construction panels, etc. An environmentally correct alternative to replace synthetic fibers composites is the naturally existing ones extracted from plants such as ramie and sisal. These have some environmental advantages of being renewable and degradable, these banana plant provide a negative contribution to C02 emission by absorbing greenhouse gas during the plant life cycle. Banana fibers have been used since long time in simple items such as ropes and rugs. Today they are used in engineering applications related insulation in building panels [2] and finish parts in automobile interior components [3]."

Jan 1, 2012

By Christian Ludwig, Virginie Silberstein, Rizlan Bernier-Latmani, Simona Regenspurg

"Residues from waste incineration (bottom ashes) form large amounts of heavy metal-rich waste. Theoretically, heating and the addition of chloride to the ashes could remove these metals by formation of volatile metal chlorides. The remaining heavy metal-poor ashes could be used, for example, as cement additives. In the proposed process of our study we used bypass dust from the cement industry as chloride additives to the bottom ashes. We aim to determine experimentally the optimal conditions to remove heavy metals from ashes and to simulate this process by thermo- chemical modeling. In our experiment we investigate heavy metal flows by heating of differently composed mixtures of bottoms ash and bypass dust in dependence of different furnace temperatures (500-1200 °C). Furthermore, we investigate the reactivity (leaching characteristic) of the resulting product in order to predict if secondary residues can be landfilled in agreement to Swiss regulations for inert materials.IntroductionThe incineration of garbage is generally considered as the most environmentally friendly method for the reduction of municipal solid waste. This is because, compared to traditional storage of waste on landfills, incineration produces less greenhouse gases and destroys toxic organic compounds. The released exothermic energy can be recuperated and the residues from the combustion chamber (bottom ash) are strongly reduced in volume. However, they still form about 600 kt of waste per year in Switzerland, which needs to be landfilled. However, these residues could be potentially used as construction materials after mechanically recovering ferrous and non-ferrous metals. However, the resulting ashes (discharged dry or wet) still contain increased amount of heavy metals (exceeding state regulation) requiring them to be finally deposed on a hazardous waste site. A thermal treatment of these ashes could enable both, to separate and recuperate the remaining heavy metals and an inorganic heavy-metal poor material. The evaporation of metals depends on temperature and can be lowered by addition of chlorides, which would lower the boiling point of most metals by formation of metal chlorides (table 1)."

Jan 1, 2008

By Joel F. Flurnerfelt

Molten Al and Al alloys containing si, Mn, Ti, and y have been lanced with nitrogen-bearing gases. These lancing experiments provided the means for observing what phases form during exposure to nitrogen-bearing gases for finite periods of time, <2 minutes, at high temperatures, >1290oC. The experiments were conducted in sn induction heated drop tube furnace apparatus. The overall premise of these experiments was to select those Al alloys and gas compositions that show promise of forming secondary dispersoid phases, particularly AIN, in the Al matrix. The alloys selected will be atomized using gas atomization reaction synthesis (GARS) using the most favorable conditions. In this case, the chosen Al alloy will be atomized with a nitrogen-bearing gas, such that the Al and gaseous nitrogen species react to form a dispersoid phase within each powder particle. The powder particles that result from this "aggressive" GARS-process would be essentially Al metal-matrix composites within a uniform distribution of dispersoids. To date, only high-purity Al has been atomized using a mild GARS reaction. This work is funded by the Materials Science Division of DOE-BES under contract number W-7405-Eng-82.

Jan 1, 1996

By T. Xin

A vertical grain boundary intercepting a horizontal free surface forms a groove to reduce the combined surface energy of the system. We study grooving by surface diffusion with anisotropic surface energy. A recently developed delta-function model of facets is used to describe the surface energy with three or four fold symmetry. It is found that the groove grows following a similarity law. The self-similar groove profile is solved numerically by a shooting method. Even with strong anisotropy, the groove profile can be smooth if the exposed surface orientations do not include a facet orientation. The smooth self-similar groove shape is the same as an isotropic groove, but the size is reduced by a factor that depends on the degree of anisotropy. This induces a large error on the value of surface diffusivity if the isotropic model is used for an anisotropic system. In this talk. we will describe how to correct for this error.1 I Xin, T. and H. Wong, "Grain-Boundary Grooving by Surface Diffusion with Strong Surface Energy Anisotropy," Acta Materialia 51, 2305-2317 (2003). Keynotes: Grain growth, Surface Diffusion, Surface energy, Anisotropy

Jan 1, 2003

By Sergio Neves Monteiro, Nuã Simonassi, Helvio Pessanha Guimarães Santafé Jr.

"Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of coir fibers. Both TGA and DTG curves were analyzed to determine the effect of the coir fiber on the thermal resistance of the composites. It was found that the coir fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.IntroductionIn recent years, there has been an increase application of natural fibers as reinforcement of polymer matrix composites in several industrial sectors, with special participation in automobile components [1-3]. Figure 1 illustrates the different components of a modem BMW sedan that are fabricated with lignocellulosic reinforced polymer composites."

Jan 1, 2012