Search Documents

By Jun Miao, Kang Liu, Jilai Xue, Jun Zhu

CO2 emissions must be reduced by at least 50 % by 2050, and hence the technical solutions to capture and convert CO2 into value–added products should be considered. A Cobalt(III) Schiff base complex (Salen–Co(III)) has been investigated as a catalyst for synthesis of cyclic carbonate from CO2 and epichlorohydrin(ECH) with tetrabutylammonium bromide (TBAB) as co–catalyst. To recover Salen–Co(III) for the next cycling operation, it was immobilized onto zeolite 13X through excessive impregnation method. The immobilized catalyst was characterized using XRD, SEM, BET and ICP–AES techniques. Catalytic tests showed that yield of cyclic carbonate reached 90 % using 0.5 mol % Salen–Co(III) at ambient conditions. The immobilized Salen–Co(III) exhibited better catalytic activity than the homogenous one when used at the first cycle, but the yield decreased by some 20 % after five cycles.

Jan 1, 2015

By Keith E. Forrester

This paper presents results of bench scale laboratory evaluation of a processes developed by FESI and Brookhaven National Laboratories for the extraction and recovery of Pb and other heavy metals from incinerator ash which was subsequently modified by FESI for the extraction and recovery of Pb from soils excavated from a FESI client scrap yard and battery breaking operation facility. The specific waste matrix presented within the paper is a battery acid contaminated surficial soil at 0" to 12" depth. The extraction method was found to be highly successful on the bench scale in generating a final post-extracted soil matrix which passed TCLP Pb regulatory limits and retained minimal Pb after aggressive extraction application. The paper findings at this time are brief, as a majority of the research results are currently being compiled and additional efforts are underway based upon initial screening findings.

Jan 1, 1995

By T. A. George, David J. Sellmyer

"The concept of achieving a useful high-energy-product magnet through appropriate nanostructuring of known hard and soft phases has been tantalizing researchers since the idea was first proposed. The fabrication of exchange-coupled nanocomposite magnets faces several challenges including aligning the easy anisotropy axes of the hard-phase grains. Here we investigate experimentally two-phase nanostructures of hard Lio-ordered FePt and soft iron-rich/cc Fe(Pt). The Fe-Pt thin films were produced by epitaxial cosputtering onto MgO (001) single-crystal substrates which lead to strong (001) texturing. The measured hysteresis loops indicate nearly ideal exchange coupling. Excellent magnetic properties are obtained, with largest values of coercivity (51 kOe), saturation magnetization (1287 emu/ cm3, J, = 16.2 kG), and nominal maximum energy product (58 MGOe).1. IntroductionA key figure of merit for permanent magnets is the maximum energy product (BH)rrw.x. The achievable maximum energy product is determined by a magnet's saturation magnetization M, and its magnetic anisotropy. For example, it is well known that (BH)rrw.x :S 4n2M,2• In the past, record energy products have been the result of discovering new compounds with high values of magnetization and anisotropy. However, finding new compounds with better magnetic properties than the current record-holding magnet Nd2Fe14B has proven to be difficult. A different approach is to exploit the exchange coupling mechanism between known hard and soft magnetic phases to enhance the maximum energy product [1-5]. In such a composite system, high coercivity is achieved due to the anisotropy of the hard phase as well as a nanostructure which prohibits large-scale domain wall reversal mechanisms. Magnetization is enhanced by the soft phase and loop squareness results from texturing of the hard phase easy-axis as well as complete exchange coupling between the coexisting hard and soft grains."

Jan 1, 2012

By Y. W. Miao

Along the south-west coast of Taiwan is about 550,000 metric tons of heavy sand deposit containing about 10 % black monazite. The Institute has developed a separation process to recover the individual rare earths and the developed process has been commercialized by a local private company. The decomposition of the local black monazite by sodium hydroxide through hydrothermal and fusion methods has been investigated. In the hydrothermal process 4.5 wt. % of aqueous alkali solution was used in an autoclave. In the fusion process, caustic soda (9.8% NaOH) was employed in am open cylindrical reactor. The same product of hydrous rare earth oxides were obtained and then dissolved by hydrochloric acid and the p-H adjusted in order to separate the thorium from the rare earths. After filtration, the filtrate contained rare earth chloride and the cake contained mainly the silica and thorium hydroxide. Both methods give a yield of 90 % with respect to the rare earths recovery. A detailed description of operation and comparison of the two methods are given.

Jan 1, 1989

By Ryuhei Masuda, Kenji Oosumi, Yasuhiko Watanabe, Yutaka Nagakura, Tomoya Ohzono

"In order to promote recycling of aluminum scrap, it is required to remove inclusions that have a remarkable influence upon the product quality. An internal filtration technology using a new filter, which is made by coating an adhesive on the surface of the conventional filter, has been developed as a new removing technology for inclusions.The technology has made it possible to remove inclusions as small as 10-20µm in the molten metal, which have been impossible to be removed by the surface filtration technology using conventional filter, An inclusion removal rate of up to 90% has been attained.The technology will contribute not only to recycling of aluminum products but also to the improvement in the quality of current products."

Jan 1, 2000

By R. Vasant Kumar

Measurement and control of trace elements in molten metal are often critical in order to achieve optimum production, refining, alloying or recycling. Solid electrolyte sensors for monitoring oxygen and very recently for hydrogen have made major impact in the metal industry. It has not proved straightforward to develop solid electrolyte sensors for many other elements that can be industrially applied in metal production. Novel self-tuning chemical sensors have been developed by the authors that may open up new technological opportunities. Three such examples will be presented in this paper: (i) a self-selecting oxygen-sulfur dual sensor using a composite beta-alumina/zirconia solid electrolyte; (ii) a copper sensor for liquid matte based upon cusicon solid electrolyte operating in a current reversal mode; and (iii) an aluminium sensor on solid NaCl containing channels of molten NaAlCl4 electrolyte formed by electrochemical charging in molten zinc.

Jan 1, 2006

By Ma Shao Xian, Li Dong, Li Zhen Guo

"The new type shaft calciner ( SK-10 Serials) is developed and designed by CADRE itself on the basis of the conventional shaft calciner. The actual application in a number of calcinations plants have proven that they are of very good effect. Calcined coke calcining heated by the shaft calciner has a high quality, lower lost by fire. The shaft calciner needs no additional fuel when it is working. Anode Carbon Plant and calcined coke Plant commonly used the shaft calciner in domestic. The waste heat from the shaft calciner can be recuperated to generate electricity and to make the steam for produce. Exhaust waste heat is recovered by 90% or more. The new type shaft calciner's structure is optimized by computer simulation for fire-wall structure, combustion air to fuel ratio, volatile combustion is fully in use, furnace cooling zone structure, the exhaust smoking structure and calciner heat balance. Furnace structure and production operating parameters has been got the best optimized results. This paper introduces the working principle and characteristics of the shaft calciner - the equipment for calcining of the petroleum coke. It also demonstrates measured process parameters of the new type shaft calciner. Through comparison with the rotary kiln and conventional shaft calciner, it proves its own technical characteristics and advantages: higher capacity, high quality products, provides more energy for power generation, equipment operation and maintenance costs lower.IntroductionChina's petroleum coke market is mainly dominated by the delay raw petroleum coke. Rotary kiln and shaft calciner are the main process equipment for calcined petroleum coke. As the shaft calciner burning less, no external fuel, waste heat utilization is high, long service life, the utilization rate in China is more extensive than the rotary kiln."

Jan 1, 2012

By Alexander A. Knminskii

Polymorphism of BaR2F8 compounds is analyzed, and some peculiarities of obtaining monoclinic low-temperature (3-BaR2F8 crystals (R=Y, Ho-Yb) and orthorhombic high¬temperature a-ßaR2F8 crystals (R=Yb, Lu) by the Bridgman-Stockbarger growth technique are discussed. We pay a special attention to BaYb2F8:Er3+ crystals, which are able to generate both 2:µm SE using the new four-level operating scheme (4F9/2?4I11/2 laser channel) and 2- and 3-µm SE by means of the cascade scheme (4F92?+4I11/2?+4I31/2). This 2-µm generation of Er3+ ions has an advantage over similar SE of Ho3+ and Tm3+ ions (especially under diode laser pumping), that is important in designing the medicine and ecology laser. We report on orthorhombic BaR2F8 crystals with the ordered structure, a new crystalline materials for generating Ln3+ ions. The growth conditions are determined and orthorhombic BaLu2F8 crystals of several cm3 in volume doped with Ce3+, Nd3+, Ho3+, Er3+, and Tm3+ ions are obtained for the first time. Spectroscopic and laser characteristics of these crystals are discussed for Nd3+-and Era+-doped samples serving as representative examples. In particular, low-threshold stimulated emission was excited in 4F3/2?+4I11/2 channel of Nd3+ ions in the BaLu2F8. Room-temperature generation was obtained also at -1.317 µm wavelength for Nd3+ and at ~2.8 µm (several lines) for Era+ ions in this new laser crystalline host with a threshold of about 20 J.

Jan 1, 1997

By R. P. Rao

In rare earth (RE) based phosphors, high luminous efficiency is possible due to their restricted emission limited to specific narrow bands. In general, these phosphor materials consist of RE ions as activators/sensitizers and/or hosts. Development of various phosphor host matrices such as alkaline earth chlorophosphates, aluminates and silicates activated by Eu(2+) as blue component, borates and phosphates of lanthanides and alkaline earth aluminates doped, with Ce/Bi and Tb as green component and Eu(3+) activated yttrium oxide and vanadate as red component has been described. Luminescent characteristics, color coordinates and suitability of these phosphor materials in high efficiency new generation lamps are presented and discussed.

Jan 1, 1989

By J. P. Downey, T. Salisbury, M. Berlin, E. Rosenberg, G. Pinson, R. Christianson, K. Gleason, W. Gleason, S. Davis

"The Center for Advanced Mineral and Metallurgical Processing is developing membrane production technology based on autocatalytic reduction of palladium from solution onto a unique, porous substrate. Surface membranes and catalytic structures are critically important to applications that range from hydrogen purification membranes to petroleum refining. Autocatalytic reduction processes represent a cost effective method of producing stable surface layered structures that have good working lives. These attributes are particularly important in the production of palladium alloy purification membranes used in hydrogen production. Although considerable research has investigated the interaction of hydrogen and palladium alloys, the mechanisms in play while the membranes form are not well understood. Preliminary research has identified three distinct deposition mechanisms and it appears that substantial control over the resulting membrane is possible.IntroductionPalladium-based membranes separate hydrogen from other gases because hydrogen is uniquely soluble in and readily passes through bulk palladium. As currently produced, palladium-based membranes are expensive and have short service lives. These circumstances are due in part to the lack of a complete understanding of palladium or palladium alloy deposition. The Center for Advanced Mineral and Metallurgical Processes (CAMP), in collaboration with the Metallurgical and Materials Engineering Department at Montana Tech and the Chemistry Department at the University of Montana, is engaged in the development of new methods and materials for hydrogen purification membrane production.In membrane production, the palladium requirement depends on substrate surface properties such as surface chemistry, porosity, and roughness. Thin, defect-free membranes have been successfully produced on substrates of porous glass, alumina, and stainless steel. However, the differences in the thermal expansion coefficients of palladium membranes and porous glass or alumina substrates cause problems at operating temperatures. The use of stainless steel substrates is advantageous because stainless steels have thermal expansion coefficients similar to that of palladium and they are stable at the required operating temperatures (Wicke, E., Brodowsky, H. and Ziichner, H. ). Stainless steel is also readily available and relatively inexpensive."

Jan 1, 2012

By Yin Zhang, Xiaoyu Huang, Mi Wang, Bencheng Du, Youduo He

"Burners are important facilities for blast furnace stoves to raise hot-blast temperature up to 1200°C. Common types of two-ring ceramic burners have very long flames so that part of combustion occurs in the upper part of the chequers and will cause damage to the refractory materials. Using computer simulation to analyze the turbulent diffusion flame in the combustion chamber, some good results were obtained. A new type of ceramic burner will be installed by Anshan Steel Complex in stoves of blast furnace number 4. A pilot experiment was done on the new burner. The experimental data have shown that the mixing condition was improved and the length of flame was shorter with the new type of ceramic burner.IntroductionPulverized-coal injection can give significant operating saving, reducing coke rate in blast furnace(BF) operation. However, during high rates of coal injection, extra heat must be compensated in hearth to maintain certain raceway adiabatic flame temperature. One of the effective methods for heat compensation is to raise hot-blast (HB) temperature up to 1200°C. Nowadays, since the fuel being combusted in stoves is BF gas only, in which the calorific value is down to round 3000 kJ/m3 , to increase the combustion ability and to provide a suitable length of flame in combustion chambers of stoves becomes more important. In other words, designing a good ceramic burner which will affect to HB temperature and stove lifetime is drawing more attention."

Jan 1, 1999

By Joo Hyun Park, Kyu Yeol Ko

The viscosity of the CaO-SiO2-xMnO-yCaF2 slags (C/S=1.0; x=10, 40%; y=0 to 15%) was measured to clarify the effect of CaF2 on the viscous flow of molten slags at high temperatures. Furthermore, the Raman spectra of the quenched glass samples were quantitatively analyzed to investigate the structural role of CaF2 in a depolymerization of silicate networks. The critical temperature of the slags abruptly increased at 15%CaF2, which was confirmed to originate from a crystallization of cuspidine using XRD analysis. The viscosity of the slags continuously decreased by CaF2 addition in the 10%MnO system, whereas the viscosity of the 40%MnO system was not significantly affected by CaF2 addition. The effect of CaF2 on the viscosity of the slags was quantitatively analyzed using micro-Raman spectra of quenched glass samples accompanying with a concept of silicate polymerization index, Q3/Q2 ratio. A polymerization index continuously decreased with increasing content of CaF2 in the 10%MnO system, whereas it was not affected by CaF2 in the 40%MnO system. Consequently, the bulk thermophysical property of the CaO-SiO2-MnO-CaF2 slags was quantitatively correlated to the structural information.

Jan 1, 2014

By Alex Probst

With low metal prices and increasing value placed on plant water and tailings disposal areas, it is becoming essential to maximize the efficiency of solid-liquid separation processes. Since its inception over 25 years ago, the use of flocculants has grown exponentially. While flocculants play a crucial role in the sedimentation process, they are also a major operating cost. Recent innovations are revolutionizing the industry once again. New thickener designs are doubling thickener-loading rates while reducing flocculant consumption. The feedwell, as the heart of the thickener, is undergoing many significant metamorphoses. With CFD and other advanced computational analysis, feedwell technology is being examined more thoroughly than ever before, The result is that the thickener previously thought of, as a "Black Box" is now being mapped and controlled with state-of-the-art technology. This paper will examine recent design improvements in all aspects of thickeners in order to project the look of the thickener of tomorrow.

Jan 1, 1999

By A. V. Tarasov

An environmentally clean and virtually waste-less technology for treatment of domestic solid waste and other toxic chloride-containing materials has been developed and proven on a full scale by the Gintsvetmet Institute in cooperation with some other Russian organizations. The proposed process resolves the acute and globally significant problem of dioxin formation. The purpose of the proposed technology is to ensure such destruction of the structural lattice of toxic compounds that would guarantee irreversible transformation of the resultant substances to prevent formation of dioxins. The preconditions that are required to achieve this purpose are: temperature of >125O0C; an oxidant excess coefficient of >I .05; a certain retention time of the products under these conditions (ADZ s); and thermal instantaneousness of the process involving a transition with no intermediate phase. These conditions were achieved with the experimental development of the Vanyukov furnace design commonly used for sparged smelting processes at non-ferrous metallurgical plants in Russia and Kazakhstan.

Jan 1, 2002

By F. L. Meng, C. S. Henkel, R. M. Alchalabi

For secondary aluminum producers to maintain a profitable melting operation, five technical factors have to be taken into account from the initial furnace building decision to the final operation and production. These factors are furnace design, furnace equipment selection, furnace control, furnace charge selection and inventory, and furnace operation. Any of these five factors, if not chosen or performed wisely, will likely result in sub-optimal melting operation. As a result the MeltSim melting optimization package has been developed by the collaborative effort of Chinook Sciences and AMCS Corporation to take into account these five factors. The package is a mixture of hardware, software, science and experience. The package incorporates years of reverb furnace operational observations, start-up installations, furnace operator experience and furnace physiochemical mathematical model development. The optimization package enables aluminum producers to design new furnaces, select and place proper equipment, optimize existing furnace operations, and convert air-fuel installations to oxy-fuel. The package provides furnace operation monitoring and advisory signals, and furnace automatic optimal control to furnace operators, shift supervisors and plant managers, all customized, based on plant and melter need and ease of information management.

Jan 1, 2000

By E. García-Ramos, P. Flores-Sánchez, E. G. Palacios, B. Zeifert, A. Romero-Serrano, M. Hallen-López

Chromium containing slags from stainless steelmaking may eventually be leached by acidic environments, therefore they should be treated before being stockpiled or land filled. In this work, synthetic slags were prepared and the effect of CaO/SiO2, Cr2O3, MgO and Al2O3 contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that CaCr2O4 and CaCrO4 are present in slags prepared with neither MgO nor Al2O3. The Al2O3-based slags mainly produced Ca2Al2SiO7 and the Cr(VI)-containing oxide complex Ca4Al6CrO16, whilst MgO-based slags produced MgCr2O4 as main mineralogical species. Additionally, Eh-pH diagrams for the Ca-Cr-H2O and Mg-Cr-H2O systems at 25 °C were constructed. The lowest Cr concentration levels in the leaching liquors corresponded to MgO-based slags owing to the stable binding of Cr in spinel with MgO. It was also observed in the Al2O3-based slags that increasing the slag basicity from 1 to 2 the leachability of the slags are notably increased.

Jan 1, 2008

By F. Raupp-Pereira, G. G. Cunto, J. A. Junkes, D. Hotza, V. P. Della

"The present work investigated the valorization of wastes as alternative raw materials for ceramic industries. Different industrial wastes based on the SiO2-Al2O3-CaO system and classified as non-hazardous were selected: sludge from varvite cutting process, sludge from gneiss breaks processes, sludge from filtration/clarification of potable water and a clay classified also as waste. All as-received residues were characterized by X-ray fluorescence, differential thermal analysis, thermogravimetry and particle size distribution. The applicability of these materials in ceramic formulations was then evaluated. The formulated mixtures were subjected to forming by pressing and extrusion followed by thermal treatment. After optimization of the processing conditions, the properties of the samples sintered at different temperatures were also evaluated. The waste materials studied proved to be alternative raw materials to natural mineral resources for the ceramic industry.IntroductionOne of the most important problems that have accompanied the humanity in recent decades is the environment’s degradation. In the same context, the natural resources exploration and technological development are phenomena which, if aren’t controlled, can cause ecological disequilibrium with unpredictable consequences [1]. It is in this perspective that recycling of various wastes assumes relevant importance.The recycling, understood here as the waste process reuse, is a common practice in the First World countries, where the raw materials have strategic aspects and the disposal techniques of solid wastes have considerable economic costs. In Brazil, the ecological conscience begins to be aroused due to, in the last ten years, the implementation of stricter laws for environmental control, in general, and licensing of waste generating from industrial activities, in special. The terms “residue” or “waste” are normally used to describe what remains of a production process; when an application for this material is not found. When wastes or residues are susceptible to be incorporated as raw materials or energy sources in a new material production, they can be understood as by-products [2].The valorization of industrial wastes is important, due to the need to pollute less and give an ecologically correct destination for wastes. The waste recycling, independent of its kind, presents several advantages in relation to using primary natural resources, such as reduction in the volume of raw materials extraction, lower energy consumption, lower levels of pollutant emissions and improvement of the health and safety of the population. The most visible advantage of recycling is the preservation of natural resources, extending its life and reducing the destruction of landscape and ecosystems [3]."

Jan 1, 2008

By Juan Ruiz-Ornelas, Yousef Mohassab, Ricardo Morales-Estrella, Hong Yong Sohn, Noemi Ortiz-Lara

The effect of mechanical activation on the reduction kinetics of magnetite concentrate by hydrogen was studied. The magnetite concentrate was milled for 8 h using a planetary mill. After the milling process, the average particle size was reduced from 14 to 4.4 m resulting in a lattice microstrain of 0.30. Thermogravimetric experiments were conducted to focus on the chemical reaction as the rate controlling factor by eliminating external mass transfer effects and using a thin layer of particles to remove interstitial diffusion resistance. The onset temperature of reduction was decreased due to the mechanical activation, and the degree of conversion was decreased by sintering of particles which was confirmed by SEM analyses. In view of the results, a reaction rate expression is discussed from which the activation energy is calculated.

Jan 1, 2016

By Taner Kavas

The refractory bricks of a rotary cement furnace containing of alumina and magnesium chromite were studied in order to determine whether they could be used in the concrete production as aggregates. Three mortars were prepared by mixing 1 part cement, 3 part aggregate materials, 0.5 part water by weight and mechanical, chemical, thermomechanical and microstructural characteristics were evaluated. The compressive and bending strength of samples were determined after 2 and 28 days curing. Resistance to chemicals were established by calculating the weight gain of mortars stored in 2 % HCl solution for 1 h and 24 h. Thermomechanical characteristics were determined by measuring the compressive strength of heat treated specimens at temperatures of 400 °C, 600 °C and 800 °C. Consequently, magnesium chromite containing waste brick aggregates have given the best results.

Jan 1, 2006

By Martín Reyes

Iron concentration by ion flotation techniques, from sulfate solutions in presence of zinc was studied in a laboratory flotation column by continuous mode using a synthesized sand shell plate sparger, an anionic collector, promoters, and surfactant propylenglicol 400. Effects of experimental parameters, such as the concentration of reagent: potassium amyl xanthate and dithiophosphate, superficial gas velocity, and superficial liquid velocity were studied in terms of the recovery and enrichment of Fe (III). The results show that the iron elimination from the solution in the presence and absence of zinc (II) are of 59 % and 72 % respectively. The flotation efficiencies decrease with an increase of the concentration of xanthate and air flow rate. The best recovery was achieved, at Jg 0.1 cm/s, Jl 0.72 cm/s and a mixture of xanthate and dithiophosphate as promoter. It was also demonstrated that it is possible to selectively separate and concentrate iron (III) from solutions containing zinc. The behavior of iron ion flotation in a flotation column is reported in this research as a gas hold up, superficial gas velocity, bubble size and superficial bubbles area flux function. The results show that the extraction of aqueous ions of metal iron by ion flotation is strongly affected by: [C], Jg (cm/s), eg (%), Db (mm), Jl (cm/s), y Sb (s-1).

Jan 1, 2009