Search Documents

By Fred L. Stanley, Ricky Q. Honaker, Michael J. Mankosa

Spiral concentration has gained a great deal of popularity as a cheap, effective method for recovering fine coal (8x100 mesh). Typically, 6-turn, wide-profile spirals are used in either a single pass, open- circuit configuration or in combination with a middlings retreat circuit. Recent work conducted at Carpco, however, has indicated that a split feed scenario and/or hydraulic classification in advance of spiral concentration offers significant advantages in both capacity and metallurgical performance. In addition, it has also been shown that the apparent density separation which naturally occurs in a hydraulic classifier provides significant up-grading in terms of pyrite and ash rejection. The results from this study will be presented in comparison with those obtained from open-circuit spiral testing.

Jan 1, 1995

By J. M. Tranquilla

EMR Microwave has developed several unique processes for the pretreatment of refractory gold and copper ores. This report describes a recent large scale pilot project involving a carbonaceous gold-bearing whole ore. Pilot plant testwork conducted jointly by EMR and Bateman Engineering Inc. has shown that 90+% cyanide soluble gold recovery is obtainable from refractory (sulphide and carbonaceous) Carlin, Nevada gold ores. Typical cyanide soluble gold recoveries for untreated material is 20%. AC energy consumption was found to be between 58.l kWh/ton and 15.5 kWh/t for an assumed heat recovery of 50% and 80% respectively. The plant was operated at reduced temperatures ( 400°C) from previous testwork on similar ore at 600°-700°C.

Jan 1, 2000

By C. A. Fleming, C. J. Ferron, I. Dymov

An oxidized gold/silver ore from Mexico has been evaluated at Lakefield Research in order to develop an economically viable treatment flowsheet for the recovery of gold and silver. Initial cyanidation test results indicated that at least 20 kg/t cyanide was required for maximum gold and silver extractions, due to high cyanide consumption by an oxidized zinc mineral present in the ore. A process was developed for the recovery and recirculation of the cyanide from the leach liquors. The proposed flowsheet included direct cyanidation, CCD and Merrill-Crowe, followed by precipitation of the zinc associated with cyanide with sodium sulphide and recycling of the regenerated cyanide liquor to the leach circuit. The process was demonstrated during a continuous pilot plant. A mill has been erected recently in Mexico and has been operating using this flowsheet.

Jan 1, 1997

By M. H. Basiri

Crude oil, as a central commercial commodity, is tied to major economic activities in all nations. Also its price fluctuation plays a significant role in global political and economic situation, as a change in the price invariably affects the cost of other goods and services. Therefore reliable forecasts of the price of oil are interest for a wide range of applications. Several approaches have been proposed over the past few years. These may divide into three categories; artificial intelligent, statistical techniques and hybrid methods. The neuro-fuzzy is one of the sub divisions of hybrid method, containing neural network and fuzzy techniques. In this paper a novel forecasting model based on adaptive neuro-fuzzy inference (ANFIS) is proposed to predict monthly crude oil price. To be able to train and test the model, the statistical data from 1990 to 2010, was obtained from West Texas Intermediate oil prices. The results are compared with a multi criteria regression analysis, it is demonstrated that the neuro-fuzzy lead an accurate and more promising forecast.

Jan 1, 2012

By M. Woodie

INTRODUCTION Information such as application review to choose the proper style of vibrating screen, parameters that determine the proper size of vibrating screen, engineering design information that governors proper screen design, review of topics that govern proper isolation from structural steel and other topics that dictate proper screen selection for applications will be presented in this paper. Topics like process and application information review to choose the style of screen and how material size and type influences proper type of screen selection (multi-slope, incline, horizontal, linear incline or dewatering) will also be discussed. Parameters will be reviewed that help size the screen for the application. The total amount of surface area to size a screen is critical to the overall success of a screen installation. Once proper style of screen is determined there is an engineering process that is required to design the screen to operate correctly in the environment it will be used. Finite Element Analysis, Dynamic Modeling, Field Vibration Analysis and other engineering tools will be reviewed to best implement a successful vibrating screen installation. TYPES OF SCREENS Multi-Slope Multi-Slope vibrating screens are used where sizing large amounts of tonnage on surface areas that would be smaller than conventional screening where roughly 6” (150mm) minus material is required to be sized. Occasionally larger particle sizes can be screened on the Multi-Slope machine but the effectiveness of the machine can be diminished with larger particle sizes and larger than 4” (100mm) screen opening. The most common and effective size range of screening with these machines is 2” (50mm) minus material. The Multi-Slope screen is used where particle size is not extremely important. Mineral processing, hard rock mining and industries where exact material size is not critical are best suited for this equipment. Because the aggregates industry requires very specific material sizes, the Multi-Slope screen is not suited for most aggregate screen applications. The key to the success of a Multi-Slope screen is proper material presentation at the feed end of the screen. This allows for the material to stratify quickly and disperse the fines through the screen quickly with a relatively thin bed depth at the feed end which allows the undersize material through the screen quickly.

Jan 1, 2019

By Hubert Erik Sherer

Determination of the best time to replace an aging unit of equipment is a recurring problem which is common to essentially all surface and underground mining operations. Virtually all mining equipment is subject to wear and the resulting deterioration that increases with equipment life. This mechanical deterioration results in lower availability and, thus, decreasing, production. Due to decreasing production and increasing repair costs, there is an optimum age at which the replacement of a given equipment unit with a new unit will result in the lowest cost per unit of production for the equipment operation in question (Figure 1). Determination of this optimum replacement age is further complicated by factors such as: possible overhaul alternatives, fleet replacement and expansion alternatives, remaining life of the mine, and technological improvements in the potential replacement or differences in the production capacities of these replacements. Determination of the optimum time to replace an equipment unit becomes more critical each successive year due to the rising capital costs of new equipment versus maintaining old equipment. An incorrect choice of the replacement age for an equipment unit can result in excessive costs to the mining operation. If a unit is replaced too early, the capital cost of the unit is not fully utilized; conversely, replacing a unit too late results in excessive maintenance costs and low production. The economic life of a piece of equipment is the equipment age that results in the lowest total discounted cost per unit of production for that piece of equipment, not considering the cost of future replacements. The economic life of a piece of equipment is usually shorter than the physical life, the maximum age at which a machine is capable of doing useful work. The optimum replacement age for a piece of mining equipment may vary from the economic life of that equipment due to the remaining life of the mine, fleet considerations, costs associated with potential replacement machines, and capital rationing constraints. For example, the equipment life of the current machine that may result in the lowest cost per unit of production might be 10 years; however, when the timing of the future replacement costs are entered into the calculation, a different life for the current machine might result in the lowest total cost per unit produced for the remaining life of the mine.

Jan 1, 1982

By H. D. R. Browner, D. A. Marsh

The need for a product dewatering step between the milling/classification and leach/carbon stages of gold plants has traditionally been performed by thickeners. Whether these be the 'conventional' or 'high-rate' types both require considerable initial capital outlay even without provision for standby facilities. In addition, their sensitivity (both mechanically and metallurgically) to changing feed conditions often results in these being considered 'high-risk' items of equipment, requiring a high degree of attention from operating personnel.

Jan 1, 1992

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By Bruce S. Brown, Jeremy P. Haile

The construction of tailings facilities and heap leach pads for gold mining operations generally requires the installation of one or more impermeable liners beneath the structures to satisfy environmental regulations and prevent the leakage of gold bearing solutions. Liners are usually constructed using clay soils or synthetic membranes, such as high density polyethelene. Low permeability soil liners can be constructed from natural clays, well graded soils with only a small clay content, or sandy soils blended with a small quantity of imported clay such as bentonite or kaolinite. The permeability of such materials, prgperly pped with good quality control, generally lies in the range of 10- to 10- cm/s, and can be designed to meet minimum prescriptive standards set by regulatory agencies. Important benefits resulting from the use of clay liners include the slow rate of penetration of a saturated wetting front, the decrease in permeability of the liner as it consolidates under the applied load of tailings or ore, and attenuation of potential contaminants in the process solutions. Synthetic liners can be attributed a finite permeability as a result of minute perforations and seaming deficiencies, and possess none of the above properties. Synthetic liners are also, by their nature, relatively thin and even a small head build-up above the liner will result in a large hydraulic gradient across it.

Jan 1, 1988

By P. Riveros, J. Binvignat, V. M. McNamara, D. Koren

The feasibility of recovering cyanide and copper from a gold mill barren solution was evaluated in a small A VR pilot plant. The campaign lasted 64 hours, during which time about 4,000 L of gold mill barren solution were processed. The results showed that A VR is an effective technology for recovering cyanide and copper from barren solutions. Under the best conditions, the copper precipitation and the cyanide volatilization attained 94% and 98%, respectively. Using 5 MNaOH as the absorbent, practically all the HCN gas was recovered in the form of a concentrated NaCN solution containing 70 g/L free CN. Basic engineering design parameters applicable to a large-scale operation were obtained, including the Henry's Law constant and the mass transfer coefficient for HCN gas.

Jan 1, 1997

By David J. Kruse

Accurate field measurements are essential when validating a conveyor design. They are fundamental in determining a conveyor's behavior, its long-term maintenance requirements, and the life expectancy/ condition of the installed equipment. Field measurements are also invaluable in forensic engineering, particularly when vital equipment has failed This paper will discuss a wide variety of data acquisition equipment, field measurement techniques and accuracies achieved State-of-the-art, custom designed monitoring equipment, as well as, ''08-the-shely instruments and sensors, will be discussed.

Jan 1, 2004

By M. D. Banghart

The Republic of South Africa is an outstanding example of the benefits to a new land by the application of individual enterprise, capital and know-how. While South Africa was colonized by European and Bantu people some 300 years ago, it was only 70 to 80 years agog when diamonds were discovered at Kimberley and gold on the Witswatersrand, that the mining, industrial and commercial potential of the country began to emerge. South Africa s national income rose from R1, 200 million in 1945 to over R4 billion in 1960 (1R = 10 shillings = $1.40 U. S.) The annual national income per head of population -- including all races -- is currently R254 (£127) This compares with £24 for India., £30 for Nigeria, and £50 for Ghana. Allowing for the increase in population, the increase in real income per head of population was about 40% during the past 15 years.

Jan 1, 1962

By A. C. T. Bigg, A. F. Colombo, A. R. MacPherson

The step-by-step study of the Stronsay ores follows the testwork through the initial determination of Bond Rod and Ball mill work indices, the MacPherson Autogenous work indices and the production of a preliminary flowsheet. These results are then used to design a pilot plant program to test the effectiveness of fully autogenous primary and secondary grinding and to determine the feasibility of controlling feed rate by the use of variable speed mill drive and/or varying the mill load. A final flowsheet is recommended with mill sizes and power requirements.

Jan 1, 1992

By L. J. Prosser, A. T. Iannacchione

From 1991 through 1995, 44 miners out of a total workforce of less than 2,000 were fatally injured in the stone industry. Of these, 12 occurred at underground mining operations with nine deaths resulting from roof or rib falls. A safer environment can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground-control strategies. Roof and rib conditions were observed and assessed in 33 underground stone mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania and West Virginia (Fig. 1). Hazard assessment indicated that the ground failures that occurred under moderate to substantial overburden, i.e., >30 m (100 ft), were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine-layout decisions

Jan 1, 1999

By W. F. Hahnert, P. A. S. Ralston

In off-line training of a rule-based controller, the significant measure of successful training is the quality of control provided by the generated rule set. In an adaptive or on-line control environment, performance is also measured by the ability to accurately maintain a satisfactory rule set, but within constraints on speed and/or resource availability. Very small population genetic algorithms, or microGAs, have been proposed as a means of capitalizing on the hill climbing characteristics of faster local optimization techniques while requiring less memory and retaining much of the robustness of traditional, larger population genetic search. A traditional genetic algorithm and a similar microGA are developed and applied to two control problems. The performance of these algorithms is analyzed with respect to (1) the quality of the rules learned, (2) the rate at which learning occurs, and (3) the memory resources required during learning.

Jan 1, 1993

By Robert A. Jankowski, Natesa I. Jayaraman, Jay F. Colinet

The U.S. Bureau of Mines evaluated the dust control effectiveness of two-phase flow systems in a full-scale model mine using a mockup of a Joy 14CM continuous mining machine. In a two-phase flow system, air and water flow simultaneously through the nozzle. Air pressure varies from 10 to 60 psi, and water at 30 to 50 psi. Coal dust was introduced at the face, and dust concentrations were monitored at the operator locations and in the return. When compared with a conventional spray system, a symmetrical two-phase flow system reduced dust levels during the box cut by 43 pct at the operator location, and 30 pct in the face return. Dust levels, however, increased at the off-operator position during the slab cut. A directional two-phase flow system reduced dust levels at both operator locations by more than 90 pct in the box cut mode. While the use of two-phase flow systems will reduce respirable dust levels and water usage, it requires an air supply to the miner. Moreover, the ability of the two-phase flow system to redirect the dust cloud makes nozzle orientation a critical factor.

Jan 1, 1991

By Ronald J. Searle, Howard S. Latham

In April 1964 the Bureau of Reclamation awarded the first contract for rapid machine excavation of a water conveyance tunnel . Since then the Bureau has excavated seven tunnels with a total length of over 190,000 feet utilizing rapid excavation tunneling machines. Tunnel bored diameters have varied from 9' 0" to 20' 10" (See Table #1) and tunnel lengths from 5,000 feet to 67,000 feet. Driver and cutter units varied from 43 rolling teeth and eight rolling discs mounted on a rotating head driven by five 200 HP 23,000 volt electric motors to 20 discs and one tricone unit mounted on a rotating head driven by two 100 HP 440 volt motors. All tunnels were driven with a laser beam guidance system governing both line and grade. Trailing conveyors and rail haulage systems were used to dispose of the excavated material. Approved Bureau of Mines diesel locomotive engines for waste trains were prevalent power sources supplemented by battery units on some projects. Sandstone, conglomerates, agglomerates, siltstone, shale, and granite were the geological formations encountered, with sandstone and shale the preponderant material . Tunnel support systems utilized were structural steel ribs; rock bolts and metal plates; and shotcrete, or combinations of these. Progress varied from 51-1/2 feet to 154 feet per working day for three shifts, depending on rock material and supports required. One contractor established a record rate of advance of over 400 feet in one day, 1,905 feet in one week, and 6,848 feet in one month. Such diversified experience in underground machine excavation methods presented an excellent opportunity to observe, analyze, and evaluate associated environmental health problems. Also, to develop measures for controlling

Jan 1, 1997

By James J. Scott

In the fall of 1976 the author started test work with Friction Rock Stabilizers in uranium mines of the West, principally in the Ambrosia Lake and Churchrock districts of New Mexico. Tests were also conducted in other uranium mines in the Rocky Mountains area. These mines are plagues with problems in ground control due to the weak formations in which mineralization occurs, mudstones, siltstones, weak sand, etc. For this reason, it is extremely difficult to obtain good anchorage for long periods of time with conventional mechanical roof bolts. Resin bolts give good anchorage but are expensive and, because of hole erosion and difficulties in installation due to inadequate equipment for mixing the resin and placing the rebar, they are not widely used. Field testing was also carried out in trona, limestones and hard and soft shale formations. The mechanism of the Friction Rock Stabi1izer support is discussed and pull test data presented for various rock types.

Jan 1, 1977

By J. Kemeny, K. Girdner, M. A. Lowery

A strategy for proactive blast planning to improve the postblast fragmentation size has been implemented at the Phelps Dodge Morenci Mine. This strategy was developed in specific phases that include stabilization of blasting practices, systematic changes in blast design and quantification of the size distribution of blasts. Implementing this new strategy would not be possible without an accurate method for quantifying the postblast fragment size distribution. The Split image processing system is now being used to assess fragmentation size using muck pile digital imaging taken on a daily basis and an online fragmentation analysis system installed at the primary crushers. Drilling and blasting variables and fragmentation size are entered into a database, spatially evaluated in a geographic information system and subsequently utilized for mine planning purposes. Using this strategy, significant improvements have been made in postblast fragmentation and continued improvements are expected in the next several years.

Jan 1, 2002

By R. J. Sweigard, R. V. Ramani

Productive and beneficial use of reclaimed surface-mined land is a concern of industry, government, and the general public. A process has been developed that will aid mine planners and public planners in the evaluation of postmining land use potential. This process involves the application of site planning principles to surface-mined land in a way that ensures productive end use of reclaimed land. The process consists of 10 basic components and is iterative in nature. Termination of the process depends on the amount of data collected and the evaluation requirements of each mining site. The analysis centers around the economic, environmental, and social impacts of the alternative land use plans.

Jan 1, 1987