Search Documents

By Carlo Grandori

Early experiences The first double shield hard rock tunnel boring machine, manufactured in 1973, belonged to the generation of machines that were equipped with 12" dia. cutters. The experiences made with the 4.3 m diameter prototype ROBBINS mod 144-151 have been reported at the 1976 R.E.T.C. of Las Vegas (1): it might be worth recalling here that, with a specific cutter load not exceeding 10 to 12 metric ton and a 4.8 r.p.m. cutterhead speed, the average advance rate was of 350 meters per month of 21 working days with a peak production of 1,050 m of advance in 40 working days, in widely weathered and fractured granitic rocks of generally precarious stability, where a precast segmental lining was routinely installed as tunnel support. Over the 8.2 km of the Sila Tunnels, several badly crushed or sheared rock zones were bored through without major problems, even with water inflows of up to 30 1/sec. The same machine, with an improved design of the telescopic-and-floating shield area and equipped with flameproof drive motors, was taken to Colombia where, from September, 1979 to March, 1982 it drove 7.5 km of the Rio Negro-Chivor Tunnel in competent siliceous shales of up to 130 MPa at an average rate of 20 m/day.

Jan 1, 1987

By J. C. Emerick

Preliminary investigations have shown that wetland-based treatment systems can be an effective and relatively inexpensive control strategy for mine drainage pollution in eastern coal mining regions. This strategy also has potential for western mining regions, although too few systems have been installed in the west to permit general evaluation of the concept for western climates. The construction of prototype systems is encouraged for some situations. Wet-land environments have the capability of removing metals by natural geochemical and biological processes, including precipitation, filtration, ion absorption, and biological uptake and accumulation. Data presented for natural wetlands receiving mine drainage show removal of iron and other metals, and high accumulation of metals in soils and plants.

Jan 1, 1988

By Edward M. Belsky

Increasingly stringent government environmental regulations will affect the availability and costs of bonding and insurance products for the mining community. New regulations requiring Environmental Impairment Insurance, Reclamation Bonds, and Cyanide Use Bonds will result in both an increase in cost and a decrease in availability of affordable insurance and bonding pro- ducts. Professional Liability Insurance for engineers that covers pollution exposures will be a must for all professional engineers working in the mining community. By understanding the problem, solutions can be structured to allow your company to obtain the mandated insurance at the most favorable cost and conditions!

Jan 1, 1991

By Michael Michaylov, Elana Vlasseva

This paper presents a method for three-phase foam preparation recipe optimization. The pressurized foam is injected into porous media of gob area for prevention and fighting of SPONCOM fires. The method includes laboratory experiments for main foam properties as well as mathematical optimization procedure. Optimization criteria are formulated reflecting foam application purposes. The influence of solid phase on foam heat stability is shown. Results from optimization procedure for four foam agents by varying fly ash consistency of foam are presented. Theoretical basis for original construction of foam generator, specially constructed for of three-phase foam generation, is set u

Jan 1, 1997

By Margaret Armstrong, Chris Roth

One advantage of kriging is that it provides both an estimate of the block or point grade, and an indication of the local precision via the kriging variance. If one assumes that the estimation errors are normally distributed, then confidence intervals for the grades can be calculated. But in mining, grades are rarely normally distributed; in general, they are skew. This is particularly true for precious metals. In this paper we study confidence intervals for variables with non-normal distributions. Using a non linear geostatistical technique, the grades are transformed into their normally distributed equivalents. Confidence intervals are obtained for these normal variables, and back transformed to give the corresponding confidence intervals for the grades, for either points or blocks. This approach is applied to gold data from the Witwatersrand basin in South Africa.

Jan 1, 1996

By A. D. Unsted

The Premier mine has been in existence for over 75 years and is closely woven into the glamour of the history of South Africa. A note on the geological formation of the diamond pipe and the gabbro gives a clearer overall picture of the mine. Mining methods for operations above and below the gabbro sill are briefly discussed. Ventilation arrangements for mining above the sill are briefly described and possible ventilation arrangements for mining below the sill are discussed in more detail. Note: conversions to S.I. units are not exact as rounding has been done.

Jan 1, 1980

By R. E. Mason

Shotcrete has been used for approximately 20 years to facilitate tunnel excavation through poor ground. Early examples of such usage in North America include the recuperation of the Granduc Mines access tunnel in Northern British Columbia, and similar work performed in the Carley V. Porter and Big Walker Tunnels in the United States. Mining companies such as Craigmont Mines in B.C. and Hecla Mines have used shotcrete in their workings for the past ten years. Shotcrete is now a widely utilized fool in the mining and tunnel construction industries in North America, but the accumulated experience is too limited for many to fully appreciate the capability of shotcrete to control ground movements and to understand the limitations of this tool. It is common, for instance, to use shotcrete to "bridge the gap" between rock bolt-supported and steel-rib supported ground and to avoid the use of shotcrete in water-bearing ground. Shotcrete can, and has been, used economically and practically under most severe ground conditions.

Jan 1, 1976

By K. V. K. Prasad

Solution of most engineering problems requires, in addition to vast numerical calculations, substantial use of practical judgement and expertise. With advances in applied mathematics and computer technology, the numerical aspects of problem solution have reached a considerable level of maturity. However, it is only recently that approaches like the expert systems methodology have been developed to incorporate the judgemental aspects as well. For rapid development and prototying of expert systems, expert system building tools or "shells" have become widely available. For the expert system developer, identification of the key characteristics of the problem domain and selection of the right expert system tool are of crucial importance. In this paper, the important attributes required in an expert system shell for use in the development of a mine ventilation planning expert system are discussed. These attributes are general in that most engineering problems in mining would have these requirements. Also, the results of an exercise undertaken to evaluate commercially available shells for application to mining engineering problems are presented.

Jan 1, 1989

By R. Balderrama Neder

A study consist in 20 column leach tests was performed for the "EI Arco" Copper ore deposit, located on Baja California, Mexico. The main purpose was to define the basic criteria like recovery and sulfuric acid consumption, for a commercial heap leach system design, to process the oxide Copper (Chrysocola) of the deposit. Leach parameters such as, amount of sulfuric acid in the cure solution, cure technique, particle size of the material, leach solution's flowrate application, leach solution's acid strength and height of the lifts, were evaluated to choose those parameters in which the results were the best ones for that particular design.

Jan 1, 1997

By P. C. O. Chukabarah

Atkinson's resistance square law is the cornerstone equation for traditional expression of energy losses in mine ventilation engineering. But the nomenclature for the various forms of energy losses are often confused for one another, misapplied or misinterpreted. These forms of energy were re-examined from thermodynamic and fluid-dynamic perspectives. Resultant expressions showed that both incompressible and compressible flow regimes in underground mines can easily be accommodated. Given the well-known three major energy forms, which are equivalent to one another but numerically unequal, corresponding equations to Atkinson's (pressure loss) for headloss and workloss were derived. The thermodynamic weight relational resistance ([w] s2/m5) associated with energy per unit weight (headloss) was dimensionalized for the first time. Also, normalized Atkinson-like equations for headlosses and worklosses were derived to ease direct computations in mine ventilation practice.

Jan 1, 1995

By Steven J. Schafrik, Michael Karmis, Zacharias Agioutantis

3-D or pseudo 3-D visualization of orebodies and mining related processes such as loading and tramming, are now commonly used by the mining industry. An approach is presented that can aid the engineer in creating the visualizations necessary for accurate presentations for use in public relations, safety training, production projections, reclamation plans, etc. It is shown that the creation of such digital representations of mining environments are independent of the mining package used to create the original mine design. Once a proper model has been created, any view of the areas is possible. These views can be taken from any number of stationary points or entered into an animation showing the progress of a mining construction. The paper focuses on the presentation of the steps used to accomplish the visualization and an example is for a quarry fill placement project.

Jan 1, 2002

By L. G. Austin

Using an instrumented laboratory high-pressure grinding rolls mill, the grinding force, gap dimension, mass flow rate and net mill power were measured for six coals and a crystalline quartz. A technique was developed to estimate the compressive stress-strain curves for compression of the materials in the mill plus the effects of elastic decompression. To reconcile the mill power and grinding pressure results, it was necessary to allow for the energy recovery on decompression. No clear correlation was obtained between the form of the stress-strain curves or the variation of specific mill power factor with the Hardgrove grindability index (HGI), although coals with the lowest and highest HGIs (i.e., 44 and 106) gave results significantly different from the other coals. Feeds below 140 mesh (105 µm) flowed more rapidly than coarser feeds and would not build up high grinding pressures. This indicated shearing and fluidlike properties rather than compression as a locked bed.

Jan 1, 1998

By Bo Forsman

The computer program SYGRISIS estimates number of units of equipment and operating costs on the basis of yearly production for different loading (wheel loader, LHD, digging arm loader) and transport (truck, train, conveyor belt, hoist, pump) equipment either individually or in any specified combination. Input data are yearly capacity, working time and technical data for the equipment. For the cost analysis input data are technical quantities and unit costs. SYGRISIS is written in TURBO Pascal and can be used on IBM compatible PCs with MS-DOS operating system.

Jan 1, 1989

By Anthony D. Hammond

INTRODUCTION A two-dimensional approach for modeling narrow-vein deposits using the TECHBASE® software was implemented at Sunshine Mining for its use in the evaluation of mineral properties. This 2-D approach prevents the overestimation of high-grade tons typically associated with the use of fixed 3-D blocks and reduces the size of the model in computer memory. The method consists of constructing a two-dimensional model oriented along the average plane of the mineralized structure. This approach works well for single, multiple and intersecting veins with the condition that each vein is roughly planar with variation in dip or strike less than 30" in order to maintain a reasonable resolution in the process of projecting data onto a plane (Figure 1). Also, a precise identification of the hanging-wall and foot-wall location is critical in ensuring an accurate representation of the vein. By using various modeling techniques, the two-dimensional model estimates metal content, thickness, tonnage, economic and dilution parameters which will be ultimately used in the identification of minable reserves. The following is a generic description of the steps involved in modeling a steeply dipping vein. DATA ENTRY A typical project database consists of drillhole coordinates, survey information, assay data and any other quantitative or qualitative data. This database can be created inside the software or imported from any spreadsheet. TECHBASE® utilizes the concept of "fields" and "records" (columns and rows) for storing data. The use of "calculated fields" enables the user to expand on the manipulation of the database with minimum memory requirements. Another important feature of TECHBASE® is the ability to replicate the structure and format of the "tables" for its use in another project and the capability of running a series of repetitive tasks by means of batch and "runlog" files.

Jan 1, 1998

By G. T. Lineberry, B. R. Yama

Artificial intelligence research has produced several tools for commercial application. Some of the techniques that are widely used today include neural networks, fuzzy logic and expert systems. Artificial neural networks (ANNs) are excellent predictive, pattern recognition and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process-control applications. Modeling of spatial data, ore-reserve estimation, tunnel design, long wall-stability prediction and geologic roof classification are additional applications in which neural networks have been applied successfully. In this study, a standard back propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, the performance of the network is measured on an independent validation set. Results indicate a mean error of less than 1 % between the actual and predicted values. A neural network model was developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values for given coordinates. The neural network not only performed satisfactorily, but in some cases performed even better than the kriging model.

Jan 1, 2000

By W. H. Schiffbauer

The U.S. National Institute for Occupational Safety and Health (NIOSH) developed an active proximity warning system called hazardous area signaling and ranging device (HASARD) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, which is worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels that are calibrated to identify levels of danger. The receiver outputs can include visual, audible and vibratory indicators, and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak and on a high wall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed, and it proved to be rugged enough to withstand the harshest of production environments.

Jan 1, 2003

By C. Douglas Lee

This case study describes the work done at the University of Arizona on the development of a computer mine model for an irregularly shaped and spotty ore deposit. The purpose of the work was to develop techniques for modeling any highly irregular deposit, for which the regular 3D fixed block model is not well suited. The deposit contained complex geology consisting of sedimentary beds that had been faulted, thrusted, and intruded by igneous rocks (see Fig. 1). The physical dimensions of the modeled ore body were 1067 m (3500 ft) along the N-S direction and 914 m (3000 ft) along the E-W direction. Topographic relief in the modeled area was approximately 274 m (900 ft). The highest grade of ore was found near the surface with mineralization extending down to approximately 152 m (500 ft) below. Using a fixed bench height of 12 m (40 ft), the model required 25 levels with the highest elevation being at 1286 m (4220 ft). Fig. 2 shows a cross section of the developed computer model of the ore deposit. The particular modeling approach selected for this deposit was the 3D irregular block model.* This meant that only the dimension of bench height was fixed at 12 m (40 ft). Irregular size blocks in the form of polygons were adopted in the model to describe the ore zones and geologic contacts. The following sections of this chapter describe some of the techniques used in modeling.

Jan 1, 1979

By A. R. Garcia, A. S. Myerson, W. R. Ernst, J. D. Carruthers, M. D. Franke, L. H. Hilzik

A method for removing nickel and vanadium contaminants from spent HDS catalysts involves pretreating the catalyst with H2S followed by extracting the metals with an acidic solution of ferric ion. The ferric ion solution alone removes significant amounts of active ingredients, cobalt and molybdenum; however, by pretreating with H2S, the extraction becomes more selective for removal of Ni and V.

Jan 1, 1988

Floc properties such as density, size, size distribution, porosity and shear strength govern the effectiveness of flocculation as a process for solid-liquid separation. Floc characteristics desired for removal of suspended solids by sedimentation or filtration, for example, are known to be different. In this study, an attempt has been made to evaluate floc density using a simplified procedure and determine the effects of various physical and chemical factors on the density of floes obtained. A brief discussion of techniques employed to measure the shear strength of flocs and the effect of various parameters on the floc strength is also presented.

Jan 1, 1988

By Leslie S. Rubin, John C. Roberge, Mackenzie Burnett

A self regulating helical inducer has been developed and tested for dry injection of coarse or fine solids into a hydraulic pipeline. This centrifugal pumping device has also been modified and tested for use as a boost pump in medium and long distance pipeline haulage systems. The helical inducer has been operated as an integral component of a slurry injection vehicle. This compact, low profile vehicle also includes crushing and screening components, solids feeding components, a track drive system for mobility and is run by a single operator. The helical injector and boost pump operate without speed and flow controls allowing for the practical hydraulic transport of excavated materials.

Jan 1, 1983