Search Documents

By J. Hanna, H. R. Gonzalez

Discussion by N.L. Hargett Dear Dr. Hanna: As discussed in our phone conversation, we are enclosing a suggested revision to the paper, "Application of Bentonitic Clays in Suspension Fertilizer Formulations," published in MINERAL & METALLURGICAL PROCESSING, May 1990. The revision will replace the second paragraph in the article. The reason for the revision is that suspensions have decreased in market share since 1984 and at present comprise an estimated 25% to 30% of fluid mixtures. This represents 6% to 7% of all fluids and only 2% to 3% percent of all fertilizers. Based on national surveys conducted by the Association of American Plant Food Control Officials (AAPFCO), suspensions comprised an estimated 25% of all fluid mixtures in 1974, 33% in 1976, 35% in 1980, 40% in 1984, and 36% in 1988. Revision to "Application of Bentonitic Clays in Suspension Fertilizer Formulations." Suspension fertilizers are an important segment of the fertilizer industry in the United States. Suspensions allow higher concentrations of nutrients (N, P2O5, K2O) than clear liquid solution fertilizers. K20 content of solutions is limited to about 10%, while suspensions can contain more than 30% K2O. Suspensions can tolerate greater variations in temperature than solutions. In suspensions, if crystallization occurs, the crystals can remain suspended in a clay jell instead of settling as they would in solutions. Solubility is not a limiting factor in suspensions, since complete solubility of phosphate is not required. This allows a wider range of phosphate materials to be used. Also, materials commonly used in formulating suspensions are less expensive and more widely available than those for clear liquids (Getsiner et al., 1984).

Jan 1, 1992

By Peter Zhang, Todd Minoski, Gabriel Esterhuizen, Jack Trackemas, Berk Tulu, Morgan Sears

Roof stability in the belt entry is critical for safe and continuous production of coal during longwall mining. Previous studies of roof falls that occurred in belt entries have shown that the roof falls were largely associated with high in situ and longwall-induced horizontal stresses [1,2,3,4]. To properly support the roof in a belt entry, it is important to understand how longwall-induced horizontal stress changes can affect roof stability in the belt entry. Monitoring of horizontal stress changes was conducted in the belt entries of two Pittsburgh seam longwall panels oriented unfavorably to the major horizontal stress. Numerical models were also set up to investigate how horizontal stress concentrates and relieves in the belt-entry roof near the face as panel orientation changes. Both measurements and modeling results show that high horizontal stress concentrates in the belt entry roof within about 15 m outby the face. The study demonstrates that longwall-induced differential horizontal stress can be used to evaluate the horizontal stress concentration factors. The horizontal stress concentration factors change with panel orientation, resulting in high stress concentrations at orientations between 20 and 110° and low stress concentrations between 130 and 180°. Roof support strategies are given for the belt entries under the influence of high horizontal stress. For unfavorably oriented panels in weak roof conditions, supplementary support should be installed during development, and cable bolts should be anchored into a stable roof horizon. The bolting pattern should be designed to cover both entry corners and the entry center to prevent potential roof cutters and sagging.

Jan 1, 2023

By J. M. Scharer, Bruce E. Halbert, Pettit. Carol M., Lysane Bolduc

The ratio of neutralization potential (NP) to acid production (AP) ratio is often employed for predicting acidic discharges from waste rock dumps. The available NP was evaluated in laboratory studies of limestone dissolution in simulated acidic mine water. The available neutralization potential strongly depended on the particle size. Using limestone particles of 114" (6.4 mm) or greater, less than 20% of the total neutralization potential was exhausted at the onset of acid conditions. Apparently, the dissolution of limestone became mass transfer limited. Under mass transfer limitations, the rate of pyrite oxidation may exceed the rate of neutralization by buffering minerals. The implications concerning the controls on limestone dissolution were examined using a geochemical predictive model for sulphide mineral oxidation in waste rock. The results have shown that in case of heterogeneous waste rock piles the NP/AP ratio is a reliable indicator for short-tam predictions only. Kinetic data on the depletion rate of the neutralizing minerals and geochemical modelling suggest that waste rock environments with NP/AP ratios as high as 5.0 may turn acidic in the long term.

Jan 1, 2000

By S. M. Moore, J. F. Burr, R. Fernando, D. Snyder

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done. As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal. TECHNOLOGY GAPS TARGETED BY THE MINER ACT The MINER Act addressed several technology challenges: • Problems with donning and switching between self-contained self-rescuers (SCSRs). • Poor visibility in smoke. • No wayfinding assistance for escape from the mine. • Limited breathable air supply. • Inability to locate trapped miners. • Inability to communicate with trapped miners. • Failure of mine seals. The MINER Act had several provisions that prescribed specific safety technologies intended to address these issues. Many of these were directed at post-accident technology requirements — an area in which Congress mandated additional technology investment. Specifically, the Act required mine operators to submit emergency response plans (ERPs) that contained provisions for implementing new or improved post-accident communications, tracking, lifelines, refuge alternatives and breathable air supplies along with training for emergency procedures and local coordination of emergency response. Most of the requirements were to be carried out within three years of the ratification of the MINER Act. In addition to these requirements for mine operators, the Act clarified and expanded NIOSH’s role and authority in enhancing the development of new mine safety technologies and expediting their commercial availability. The MINER Act also required NIOSH to develop research on refuge chambers, mine seals and the use of belt air and fire-retardant belts. Mine seals had to be upgraded and MSHA turned to NIOSH for applied research to establish the new explosion-resistance requirements. Progress toward closing the gaps."

Jan 1, 2017

By Biswajit Samanta, Pranjal Pathak

A multimine mineral value chain (MVC) consists of multiple mines in the upstream supplying raw materials to multiple destinations in the downstream. The short-term mine production scheduling problem of a multimine MVC aims to determine the optimal extraction sequence and destination allocation of blocks from all the mines collaboratively to meet the quality and quantity requirements of all the processing plants in each period, subject to all relevant technical and operational constraints of the mining system. It is carried out at shorter scales of days/weeks/months under the purview of long-term production scheduling. An optimal short-term production schedule for MVC involving multiple mines that share the same infrastructure (processing units, stockpiles and waste dumps) requires coordination across the network of mines. Optimizing the short-term production schedules independently at each mine fails to capture the benefit of collaboratively generating schedules for all the mines, resulting in suboptimal schedules. Additionally, in short-term production scheduling, the operations are modeled in greater detail with additional decision variables and constraints to model the more complex multimine MVC situations. This makes the large-scale instances of the problem computationally intractable for standard mixed-integer programming (MIP) solvers. This work presents a customized genetic algorithm (GA)-based heuristic approach to obtain near-optimal solutions to the industrial-scale instances of the short-term production scheduling problem of multimine MVC within a reasonable computation time.

Oct 1, 2022

By P. G. Semple, K. W. Major, P. Eng.

The recent increase in development of refractory gold deposits has resulted in changes to the traditional treatment processes. The selection of the preferred refractory treatment process is dependent on the mineralogy of the ore. One process, which has recently gained increasing attention, utilizes dry grinding and roasting of the whole ore. This paper will discuss some of the considerations to be addressed during the design of the process fl owsheet and what the effects of the various alternatives will be on the plant capital and operating costs. The paper will be based, in part, on current experiences with dry grinding, roasting plant design and start-up.

Jan 1, 1990

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

A ventilation study was conducted at a western U.S. coal mine to evaluate the movement of longwall face air and exchanges between the face and worked-out areas to document the presence or absence of face airflow pathways between these locations. This field study was part of a project investigating the effect of longwall face length and caving characteristics on longwall face air behavior and its potential movement on and off of the face. Tracer gas experiments using sulfur hexafluoride (SF6) were done to describe air movement on the face and in the mined-portion of the active panel. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob.

The process design of a metallurgical plant follows logical steps, one built on another, to define the circuit requirements. The methodology used and documentation produced is the same for a pre-feasibility study, feasibility study or a complete design, regardless of the process complexity or the commodity. The only difference is the amount of detail developed at each stage. SRK Consulting, an independent, international consulting practice that provides focused advice and solutions to clients, mainly from earth and water resource industries, has consulted on many mining projects around the world. The company was formed in 1974 and now employs more than 1,600 professionals in more than 50 offices on six continents. According to SRK experts, the first element in plant design is collecting metallurgical testwork or operating data from an existing plant. The testwork identifies the process, the metallurgical recoveries and product qualities and establishes the process parameters for economic recovery of the commodity. Test samples must represent both the whole orebody and the feed over the life of the mine, showing the mineral?s variability. With this data available, the process design can be developed.

May 1, 2013

By A. Ferreira Morgado

The sodium smectitic clays (bentonites), have more industrial applications in that class of mineral, a driving force to obtain this mineral. In Brazil, there are several occurrences of smectitic clays, unfortunately they are polycationic, with a distribution of several exchangeable cations, where the cation sodium occurs in minor quantity. In this work, the original polycationic smectitic clay was firstly proper characterized and then treated with sodium carbonate obtaining homoionic sodium smectitic clay. The rheological tests in the optimized sodium smectitic clay showed good results for drilling fluids, typical of a sodium bentonite ones.

Jan 1, 1999

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

This paper presents the results of an investigation into the effect of pore pressure regime on the factor of safety (FS) and the anticipated critical failure mechanism for a fly ash storage facility. In this study, pore pressure measurements from standpipe piezometers and pore pressure estimated from seepage analysis were used for a comparison of the estimated FS for a fly ash slope. This comparison was applied for static and seismic scenarios. To account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation, a probabilistic analysis was performed. The slope stability analysis was conducted in 2D and 3D, adopting the limit equilibrium analysis approach, and a finite element seepage analysis. The results suggest consistency of failure surfaces for 2D and 3D and an increase in FS values of 5 percent for the 3D approach, limitations of standpipe piezometers. The study demonstrated the sensitivity of the FS value, and the implication of adopting representative material properties, and water table levels, especially in cases where limited data are available, and assumptions need to be made to assess the long-term stability of a fly ash dam facility.

Aug 1, 2024

By Ihsan Berk Tulu, Deniz Tuncay, DYKE MARK ALEXANDER VAN, Ted M. Klemetti

Bleeder entries are critically important to longwall mining for the moving of supplies and miners as well as the dilution of mine air contaminants and must stay open for many years. In this study, standing supports in moderate cover bleeder entries were observed, numerically modeled and instrumented by researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH). The measurements of the installed borehole pressure cells (BPCs), standing support load cells and convergence meters, and roof extensometers are presented in addition to the numerical modeling results and visual observations made by the NIOSH researchers in the bleeder entries. The results include the effects of multiple panels being extracted in close proximity to the instrumented site as well as over one and a half years of aging. As expected, standing supports closer to the longwall gob showed the greatest load and convergence. The roof sag appeared generally independent of the proximity to the longwall gob. The BPC readings were driven by both the proximity to the gob and the depth into the pillar. The results of this study demonstrated that the entry roof can respond independently of the pillar and standing support loading. In addition, the rear abutment stress experienced by this bleeder entry design was minimal. The closer the mine development, pillar or supports are to the gob, the greater the applied load due to rear abutment stress.

By David Dvorkin, Thomas C. Anderson

INTRODUCTION A major function of the Mine Safety and Health Administration (MSHA), Denver Safety and Health Technology Center (DSHTC), Ventilation Branch, is to provide engineering analyses of underground mine¬ ventilation systems for coal, metal, and nonmetal in¬spection departments in accordance with field surveys and data analyses. Health and safety problems such as the control of diesel contaminants, dust, methane, radon, and radon daughters all are dependent upon ventilation. It is necessary for the ventilation engineers at DSHTC to have a complete understanding of the various and highly complex ventilation systems used in the nation's mines. Only through the proper assembly and analysis of data can the engineer determine the causes of prob¬lems and make suitable recommendations. Furthermore, the engineer must have the ability to predict the results of any such recommendations. In the study of the ventilation system at any indi¬vidual mine, it is common practice to collect data on airflow quantities and pressures at key points throughout the mine. However, these data give only a single point¬-in-time view of the system. As the mine develops and progresses, the system undergoes numerous changes; as the mine becomes more extensive, the ventilation re¬quirements increase, and the costs rise. For proper utilization of the available resources, it is necessary for the engineer to have a sound engineering basis for deci¬sions on how best to ventilate the mine. To evaluate the system as a whole, particularly re¬garding possible system changes, it has become necessary to rely on computers to perform the calculations in¬volved in analyzing the network. This chapter sum¬marizes the implementation of such computer capabili¬ties at DSHTC, as well as the services that are available from DSHTC. ANALOG SIMULATIONS AND ANALYSES OF VENTILATION NETWORKS As early as 1954, the US Bureau of Mines (USBM) in Pittsburgh, PA, was using an analog computer as an aid in analyzing ventilation systems. The Mcllroy Fluid Network Analyzer used filament-tube resistance elements and an electrical power supply to simulate mine-ventila¬tion systems electrically. This system is shown in Fig. 1. Analog simulation has proven to be a practical tool, providing fast analyses of complicated problems after the initial setup has been completed. Advancements in electronic technology over the past 24 years have made possible the construction of an analog computer that has streamlined several operating features of the previous machines. The DSHTC Ventilation Branch now has an improved electronic analog computer to assist in the analyses of ventilation systems. General Features As shown in Fig. 2, the analog computer used at the DSHTC Ventilation Branch has three "element" cabi¬ nets, a console, and a printer. The cabinets contain the fan elements and the airway-resistance elements that are used to "program" an analysis problem; each element is independent of the others. The console contains the "patchboard" and the controls necessary to operate the analog computer. The patchboard connects the inde¬pendent elements into the circuit appropriate for simu¬lating the ventilation system. The total system is controlled from a panel on the console, while the value corresponding to each element is set on the individual controls located on the face of each element. The control panel has three visual output displays that give the quantity of flow, the pressure of the output junction with respect to a datum, and the differential pressure across each element. The control panel also allows manual selection of the element to be monitored, or automatic scanning and printing of values for the entire system. Capabilities The analog computer can simulate an existing mine¬-ventilation network. This is accomplished by collecting field data at the mine to give a complete pressure-¬quantity network. Resistance values for each airway branch may be determined from the quantity of flow in the branch and from the pressure differential between the end-point junctions of the branch. The basic rela¬tonship to determine the resistance is expressed as: H=R •Q2 where H is the pressure differential, R is the resistance, and Q is the quantity of air in the flow. After the resistance values are known for all of the airways in the circuit, the elements on the analog com¬puter can be set to the corresponding values. The elements are designed to reflect the basic relationships, with electrical potentials corresponding to pressures and

Jan 1, 1982

By John Ralston, Jinming Duan, David R. E. Snoswell, Daniel Fornasiero, Jingwu Yang

The colloidal stability of synthetic silica spheres with clean, methylated and dehydroxylated sur¬faces was studied at different concentrations of dissolved gas and KCl electrolyte at a fixed pH of 4.2. A classic stability ratio/electrolyte concentration analysis shows that hydrophobic, methy¬lated particles undergo faster rates of aggregation with increasing concentrations of dissolved carbon dioxide. Similar data for hydrophilic particles and dehydroxylated particles show no change as a function of dissolved carbon dioxide concentration. Zeta potential data behave simi¬larly, showing a strong influence of dissolved gas only for methylated particles. The results are interpreted in terms of DLVO theory, with the surface-to-surface interaction dominated by the presence of very small protruding bubbles. Direct evidence for the existence of these very small gas bubbles (or "nanobubbles") was obtained using tapping mode atomic force microscopy. Small bubbles do not form on smooth, hydrophilic, or dehydroxylated silicon oxide water sur¬faces immersed in aqueous solutions under known levels of gas supersaturation. Randomly dis¬tributed small bubbles were observed over the whole surface of observation on methylated surfaces of controlled roughness. Bubbles formed on rough, methylated surfaces were larger and less-densely distributed than those on a smooth surface of similar hydrophobicity. The process of bubble coalescence was observed as a function of time. The macroscopic contact angle, measured with respect to the aqueous or gas phase, is very different from the microscopic contact angle detected by TMAFM and appears to be due to the influence of line tension at the pinned three¬phase contact line. The latter has a value of -3 x 10-10 N and acts to stabilize the small bubbles, flattening them and thereby reducing the Laplace pressure.

Jan 1, 2005

By Mirza Muhammad Zaid, Nana A. Amoah, Ping Chang, Guang Xu, Ashish R. Kumar

The key takeaway of this study is the significant improvement in dust protection for roof bolter operators in underground coal mines. The optimized canopy air curtain (CAC), with a redesigned two-level manifold system, provides uniform airflow distribution that effectively reduces dust exposure. By enhancing the protection of operators from harmful respirable coal and silica dust, this technology can reduce the risk of diseases such as coal workers’ pneumoconiosis (CWP) and silicosis. The application of this optimized CAC design in real-life coal mining operations can dramatically improve worker health and safety by minimizing dust-related exposure, ensuring compliance with industry regulations and prolonging the lifespan of mining equipment by reducing dust accumulation.

Dec 1, 2024

By D. C. Sisti

A paper was presented during the 1970 SME Fall Meeting on the Stinson Preparation Facilities by representatives of Beaver Creek Consolidated Cool Company and Heyl & Patterson, Inc. This paper summarized a combined approach to development of a flow diagram and selection of cleaning equipment required to produce a uniform metallurgical coal at maximum recovery with special emphasis on sulphur reduction. These facilities were located in the Elkhorn. Coal Fields of eastern Kentucky and, in particular, the area of Wayland, Knott County, Kentucky, where approximately forty-five- million tons of Elkhorn No. 3 coal could he recovered. The facilities incorporated a Bradford Breaker for reduction of the ROM coal to minus 1-1/2 x 0, 6000 ton-raw coal storage, preparation plant, water clarification and thermal drying facilities, clean coal storage and a 4000 TPH unit train loading facility.

Jan 1, 1973

The following errors were inadvertently included in "How millisecond delay periods may enhance or reduce blast vibration effects" by R.M. Wheeler in the September issue of Mining Engineering.

Jan 1, 1987

By Jozef Stachulak

Prof. H. Bystron: "An Application of the First Law of Thermodynamics to Winter Dry Air Flow in Mr. Stachulak's Mine Model". [ ]

Jan 1, 1980

By P. R. Bridenbaugh

The products of the coming decade will possess such stringent design criteria that it is unlikely today's monolithic materials will be able to meet them. The discovery, characterization and cost- effective manufacture of a whole new generation of highly engineered materials therefore have become essential requirements for participation in the materials marketplace of the 1990s and beyond. Meeting these challenges will require advances on a broad variety of scientific and engineering fronts, including: strengthened fundamental understanding of materials behavior; composite and laminate programs offering the compatible and synergistic combination of metals, ceramics and polymers; advanced engineering and structural design techniques; processing technologies capable of producing advanced materials efficiently; and, the development of new products taking advantage of the availability and cost-effectiveness of these highly engineered, advanced materials.

Jan 1, 1986

By Marie-Josée Banwell, Cyriac Sebastian, Giacomo Falorni, Sara Del Conte

Interferometric Synthetic Aperture Radar (InSAR) is a satellite-based monitoring technique that complements other in-situ methods for detecting and measuring surface displacement. Recent advances in data processing algorithms, coupled with the use of high-resolution satellite systems, make it possible to now provide high-frequency InSAR monitoring services, with updated results delivered every time a new satellite image is acquired. The advent of large, continuously updated data sets, however, brings new challenges, including the need to rapidly sift through the data to identify only those points showing relevant ground displacement information. This has been achieved by using trend variation analysis tools, that quickly isolate and highlight only areas of anomalous behavior. The paper focuses on project case studies where continuous InSAR monitoring has proven to be key in identifying displacement trend changes near tunnel alignments.

Jun 13, 2021

By Achille Balossi Restelli, Elena Rovetto, Andrea Pettinaroli

"The Station “C13” of Warsaw Underground Line II, with tunnel crown 10m below the water table, required the excavation of three connection tunnels, underpassing a six-lane in service road tunnel, working from two lateral shafts. After the collapse occurred while digging the first tunnel, the use of artificial ground freezing was chosen to ensure the excavation under safe conditions. A complex freezing pipe geometry and excavation sequencing was necessary because of the interferences of the overlying road tunnel diaphragm wall foundations, shaft internal structures and previous grouting activities. A combined freezing method was used: nitrogen for freezing the tunnel arches, brine for freezing the intermediate wall and for maintenance stages. Sandy and silty sandy layers were frozen around the crowns and sides. No treatment was necessary for the inverts, lying in clay. A monitoring system of ground temperatures and structure movements allowed for successful completion of work in 8 months. INTRODUCTION The C13 Station of the Warsaw Underground-Line II is located on the West bank of the Vistula River. It consists of two shafts and three connecting tunnels, passing under the Wislostrada (WS) Road tunnel. According to the initial geotechnical investigation, tunnels should have been excavated in high-plasticity clay, but during the first borings non cohesive soil was encountered. Additional investigations were performed on both shafts and a more detailed stratigraphy was reconstructed (Lombardi et al. 2015). Layers of fine sand, sandy silt and sandy silty clay were present along the tunnels crown arches and in the North East tunnel they extended down to the centre line (-13.735m above the Vistula River medium level). Based on the new stratigraphy, it was decided to stabilize the crown and control the groundwater inflow from the face with jet-grouting columns extending the treatment down to the clayey soil, but a collapse occurred in the North West tunnel with soil and water inflow inside the shaft."

Jan 1, 2016