Search Documents

By L. C. Atkinson, E. A. Azrag, T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is a more realistic simulation of the problem, but the former method is significantly easier to use. Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.2 to 0.6. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1995

By Fiona Woody

Lime and calcium products are essential building blocks to the modern world, used to purify drinking water, preserve foods, control pollution, improve crop yields, stabilize soil, pave roads and support the production of steel, cement, glass and many other industrial processes. While lime is essential to society, it also has a sizable carbon footprint. Approximately 30 percent of the scope 1 greenhouse-gas emissions generated during lime production are related to fuel combustion, while the remaining 70 percent are created by the unavoidable chemical reactions during calcination.

Feb 1, 2026

By William H. Mount

INTRODUCTION Effective mine ventilation is required to maintain a healthy underground environment for humans. Without effective ventilation, the environment can become unhealthy or hazardous as a result of the depletion of oxygen, contamination with toxic gases, or the buildup of an excessive amount of particulate matter (dust). Each contaminant has an upper limit of concentration that should not be exceeded within an 8-hr period. This is known as the threshold limit value (TLV). The TLV represents an acceptable level of exposure that should produce no ill effects. Unfortunately, more than one contaminant may be present at any one time and the effects of the individual contaminants may be additive, i.e., the effects of each contaminant must be considered simultaneously to determine the potential danger to miners. Possibly the greatest threat to mine-air quality is the uncontrolled underground use of the diesel engine. The diesel engine was invented in 1892 by Rudolf Diesel. His intention was to develop a power source that could burn coal dust as a fuel, but he was unsuccessful in that attempt and had to resort to liquid petroleum fuels (Johnson, 1975). In 1898, the diesel engine was intro¬duced into the United States by Adolphus Busch, who anticipated using it as a prime mover in factories and generating plants. At that time, the diesel engine was a very large and very heavy engine, designed for fixed installations. By 1919, lighter engines were being developed, and by 1931, Caterpillar was marketing a diesel-powered, track-type tractor (Henderson, 1975). Since 1931, the diesel engine has evolved into an extremely popular prime mover in medium and heavy-duty applications. Efficiencies now are on the order of 40% and improvements such as turbocharging and aftercooling have produced engines capable of generating power at a ratio of 0.3 kW/kg (1.0 hp per 5.0 lb) of engine weight. Although the diesel engine is relatively efficient as a mobile power plant, it is far from efficient in terms of the energy produced from the energy potential of the fuel. About 60% of the heat value of the fuel leaves the engine as wasted heat, with about 50% of that heat being emitted through the exhaust pipe and the other 50% being emitted through the radiator or cooling fins. Perfect combustion in an engine would produce only water vapor (H_0), carbon dioxide (CO_), and nitro¬gen (N2) as the byproducts. Since the diesel is not a perfect engine, each pound of fuel burned generates 5.6 m° (200 cu ft) of exhaust gas, containing about 0.009 m3 (0.33 cu ft) of carbon monoxide (CO), 0.009 m' (0.33 cu ft) of nitrogen oxides (NO, NO2, and NOD), and 0.57 m3 (20 cu ft) of carbon dioxide. The balance of the exhaust emission consists of free nitrogen and water vapor (Hurn, 1975). Contrary to popular belief, the diesel is not inherently dirty. Under normal operating conditions, a well-maintained engine neither smokes nor smells. However, the same well-maintained engine can and does produce toxic emissions. A diesel engine is not inherently safe and constitutes a distinct hazard to personnel. This chapter is devoted to a description of the various toxic substances that may be generated by a diesel engine. Although some of these substances may also be produced by blasting or natural causes, the focus of this chapter is on the relationship between the internal- combustion compression-ignition engine (the diesel) and the quality of the mine air. CARBON MONOXIDE Combustion Process During the combustion process (burning) of organic fuels, each atom of carbon combines with two atoms of oxygen, provided that a surplus of oxygen atoms is available. Thus, the carbon is oxidized to carbon dioxide. Most open flames, such as trash fires, camp fires, gas ranges, etc., produce carbon dioxide. However, with insufficient oxygen, incomplete combustion results as the carbon atoms each combine with one atom of oxygen to produce toxic carbon monoxide. Burning charcoal briquettes produce carbon monoxide because the combustion takes place inside the briquettes where sufficient oxygen is not available to the combustion process. Internal-combustion engines, whether burning gasoline or diesel fuel, also produce carbon monoxide. The only oxygen available to the combustion process is that trapped within the cylinder. If the amount of fuel delivered to the cylinder is excessive, there is insufficient oxygen for complete combustion and carbon monoxide production results. In a normally aspirated (nonturbocharged) diesel engine, the amount of air "sucked" into a cylinder is the same on every intake stroke, resulting in complete combustion only at low levels of engine loading, when small amounts of fuel are injected. Higher levels of engine loading cause larger amounts of fuel to be injected into the same volume of air in the cylinder. Unless the volume of air is increased, the combustion process becomes progressively less complete as the amount of fuel increases. Turbocharged engines are able to compensate some¬what for increased loading and increased fuel consumption. The turbocharger acts as a compressor for the intake air, forcing a larger volume of air into the cylinders as the engine speed increases. Hence the turbocharged engine burns cleaner than a naturally aspirated engine and produces slightly less carbon monoxide (Marshall and Fleming, 1971). Much of the underground equipment used today is powered by turbocharged indirect-injection diesel engines. Although these engines emit fewer toxic contaminants than naturally aspirated engines, they do not eliminate the problem. Since the turbocharger is driven by the exhaust gases, rapid accelerations can cause temporary overfueling of the engine until the turbocharger attains a speed sufficient to restore the correct air-to-fuel ratio. During this "turbocharger lag," the combustion cylinders contain insufficient oxygen, causing severe smoking and an increased output of carbon monoxide.

Jan 1, 1982

By Dhananjay Kumar

In past, no serious attempts have been made to study the effects of operating environments on performance characteristics of a mining system. In this paper, proportional hazards model (PHM) analysis technique is introduced which can be used to analyze the effects of operating environments on the performance of a mining system. It can be used to select suitable materials, manufacturers or designs of items for a particular working environment. In this paper some applications of the PHM are discussed with examples from a Swedish mine. Its application for decision making in maintenance is also discussed.

Jan 1, 1992

By Janet Briggs, Michael Vertes, J. F. Shirley, R. E. Cutherbertson, Alexander Sutulov, J. D. Vincent

Molybdenum, the 42nd element in the periodic table, is now a very important metal in industry of the United States and the world. Chemically, it is a very complex element having valences of 0, +2, +3, +4, +5, and +6, and can exist as a mixture of these valences in many compounds. It was discovered and separated by Scheele in 1778. At the present time, molybdenite is the only important commercial source of molybdenum. Molybdenum occurs in some 12-14 different recognized minerals, but practically all of the production is molybde¬nite. As late as 1915, it was considered a rare metal. Germany made extensive use of it during the first world war, which resulted in the establishment of a molybdenum industry in the United States at Cli¬max, Colo., in 1917. It was not until the mid-1920s when its introduc¬tion to steelmaking developed for the US automobile industry that the metal gained important acceptance. The first notable example was the Willis-Saint Claire automobile introduced in 1921 by C. Harold Willis, formerly chief metallurgist for Ford Motor Co. Molybdenum has also been produced in the US from wulfenite (PbMoO4) from Arizona and Nevada, and a small amount of molyb¬denite was produced up to the early 1970s as a coproduct from two molybdenum-bismuth mines in Quebec, Canada. The first byproduct production of molybdenite from a copper con¬centrating operation was achieved at Cananea, Sonora, Mexico, and was followed shortly by the Utah division of Kennecott Copper Co. in the mid-1930s. This section of the Handbook is divided into four main subdivi¬sions: Chapter 2, which deals with the concentration and recovery of molybdenite from primary molybdenum ores; Chapter 3, which deals with the recovery and separation of molybdenite as a byproduct from copper production; Chapter 4, which deals with the conversion practices employed for converting molybdenite to the oxide or metal form; and Chapter 5, which covers the uses of molybdenum in steel¬making, chemicals, pigments, lubrication, catalysts, etc. The Free World molybdenum production, for the past eight years from all sources, is shown in Table 1. 2. Primary Molybdenite Ores General In 1978 there were four primary molybdenite recovery plants in operation: Climax, Endako, Quests, and Henderson. For over half a century the Climax mine has been by far the largest and most important source of molybdenum in the world. During the early 1970s a few primary molybdenite mines in British Columbia were shut down due to adverse economical conditions. The largest of these was British Columbia Molybdenum, formerly owned by Kennecott Copper Corp. The Climax plant and operations are described in detail and the opera¬tions of the other plants are summarized following a general discussion of recovering molybdenite from primarily molybdenite ores. Recovery of molybdenite as a byproduct will be taken up in Chapter 3. Geology Molybdenite production from mines in which it is the sole or preponderantly important mineral is confined to ore bodies in granites or igneous-type rocks or pegmatite dikes. More than one state of mineralization is sometimes present as at Climax, York, Hardy, and Questa. In the case of Climax, important byproduct recovery of tung¬sten, tin, pyrite, and monazite is also attained. The molybdenite is commonly disseminated very finely in the siliceous granitic gangue but does occur in stringers and blebs in silicified mineral solution channels. Treatment of Primary Molybdenum Ores All primary molybdenum ores are low in molybdenite, the content ranging from less than 0.20% MoS2 to a high of about 0.40% MoS2. A high resistance to grinding is a common ore characteristic combined with a habit of very fine dissemination of molybdenite in the siliceous portion of the ore. Because of low MoS2 content, high hardness, and fine dissemination of molybdenite in primary ores, it has been necessary to develop a special mill treatment which yields an accepta¬ble recovery at a reasonably low milling cost. Essentially, the treatment consists of intensive rougher flotation at a relatively coarse grind with production of a low grade rougher froth containing a substantial percentage of the molybdenite in the form of low grade middling particles, followed with multistage regrinding to liberate the locked molybdenite and several stages of flotation cleaning to produce a finished grade concentrate. Rougher flotation on pulp ground to ap¬proximately 35 mesh is common practice, even if complete liberation of molybdenite from siliceous gangue may require regrinding to 200 mesh. The flotation of middling particles with a very low content of molybdenite in the rougher flotation step has been made possible by the application of a combination of reagents first developed at the Climax mill and used with some modification in the treatment of all primary molybdenum ores. The reagents commonly employed and their functions in flotation are:

Jan 1, 1985

Allis Mineral Systems' Grate- Kiln system can economically convert low-grade iron ore into high- grade iron-ore pellets suitable as feed material for blast furnaces for making steel. These pellets can also be fed to a direct reduction process for making sponge iron. The Grate- Car system combines the company's [ ] Grate-Kiln system for iron-ore pelletizing and Accar system for iron- ore reduction. The Grate-Car system consists of a traveling grate, a ported rotary kiln and a rotary cooler that are coupled in series. This system eliminates the pelletizing plant's rotary kiln and annular cooler. It reduces the need for some auxiliary equipment. This results in lower capital cost and lower energy consumption. The traveling grate provides that static bed handling necessary for heat hardening pellets before their discharge into the kiln. The ported kiln provides the reducing atmosphere with a more precise means of controlling the kiln axial temperature profile than conventional rotary kilns.

Jan 1, 1997

By I. Kapageridis

The mining industry worldwide has recognized in the past the need to apply specific rules and guidelines in the reporting of mineral resources and reserves. The high financial investment and risk associated with any mining project and the ever stricter environmental and social controls were the forces behind this recognition. For years the industry experienced the development and enforcement of several codes for reporting accepted by different countries. The implementation of any code can be a confusing task as the guidelines are sometimes general and open to different interpretation. The use of computers in the estimation and reporting of mineral resources and reserves is necessary, particularly when trying to implement particular code guidelines. This paper discusses ways to implement a reporting code in a computerised resource/re-serve estimation study. The implementation is demonstrated using a gold deposit project as an example. The effects of mining, metallurgical, economic, marketing, legal, environmental, social and governmental factors are taken into consideration. This paper also discusses well established reporting codes and the possibility of reaching a single, universally applied code that could be used by Greek mining companies.

Jan 1, 2007

By T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground-water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is obviously a more realistic simulation of the problem, but the former method is significantly easier to use, Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.15 to 0.60. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1992

By D. W. Wu, M. T. Haque

A novel impedance probe was commissioned specifically for capturing fast dynamic information about filtration processes. It provides an attractive alternative to more complex measurement techniques in situations where the slurry system is primarily one-dimensional. The probe can monitor mudline, slurry densification and drainage. Dynamic variations in cake permeability are obtained by combining dynamic mudline information obtained with the probe and filtrate rate data derived from a leaf test apparatus. The measurements are reviewed in relation to micro structural measurements obtained on iron ore filter cakes. The practical significance of these measurements for optimization of the filtration process is discussed.

Jan 1, 2002

By Randal J. Barnes, Franck Rellier

Mine ventilation survey data includes generally redundant, usually inconsistent, often incomplete, and always noisy measurements. Yet, these data are essential for operational decisions and represent the foundation of any mine ventilation systems model used for future engineering analysis and design. For example, the basic ventilation network geometry can be measured with a reasonable precision, the network flows can be measured, but with significant errors, and the branch resistance factors can not be directly measured at all. The network-based, constrained weighted least squares approach, presented in this paper, advances a method for the sys tem-wide adjustment of ventilation branch measurements and the consistent estimation of global system parameters (e.g. branch flows, head losses, and resistance factors). The constraints guarantee that the adjusted values satisfy the governing physical laws: conservation of flow, conservation of energy, and the appropriate energy dissipation rule (e. g. Atkinson's RQ2). The weights allow for the proper inclusion of data with widely disparate precision, as well as offering a simple method for retiring old data as the mine changes through time. The post-adjustment sensitivity analysis presents two potentially useful forms of analysis: the identification of previously unspecified leakage branches, and the semi- automatic recommendation for future ventilation measurement campaigns. The overall efficiency of the algorithm is exemplified by the fact that a ventilation network with hundreds of branches and thousands of measurements can be routinely adjusted on a microcomputer.

Jan 1, 1989

By Theodore Triplett

To assess the value of various subsidence mitigation techniques, twelve linear foundations were constructed above a longwall mine. The structures were monitored during and after undermining, and footing curvatures at the time of cracking were compared with predicted values. An unreinforced concrete footing sustained substantial damage. Other footings received varying degrees of damage, with inclusion of a sand layer significantly affecting performance. A post-tensioned concrete foundation suffered minimal cracking. Also, a technique developed by the Bureau of Mines is presented for determining the subsidence, slope, curvature and strain of the ground surface.

Jan 1, 1986

By J. J. Snodgrass

Faults, sandstone channels, and abandoned mine workings present severe safety hazards, disrupt mining, and necessitate costly precautions or discontinuance of operations. In addition to fault detection, mining companies have a need to map discontinuities such as seam thinning and previously mined areas in both longwall and room-and-pillar operations. Initial field tests demonstrated successful generation and propagation of higher order guided wave modes. Theoretical studies indicate potential for improved resolution by sensing small details in the coal seam and roof structure. Controlled- waveform source transducers and specialized detectors are particularly useful to preferentially excite and detect the Love (SB) and Rayleigh-type (P-SV) waves, including the higher frequency modes. The distinct observation of reflections using the transducers in the shear wave mode makes feasible the detection of the water-filled voids.

Jan 1, 1984

By B. J. K. Sullivan, Brian Hornsby

INTRODUCTION Mount Isa Mines Ltd. operates a copper and silver- lead-zinc property at Mount Isa in northwest Queens- land, Australia. Mount Isa is located in the tropics at latitude 20°43'S and longitude 139°30’E (Fig. 1). It is on the upper watershed of the Leichhardt River and at an elevation of 365 m above sea level. The average rain- fall is 360 mm/y, the greater part of which falls in January to March (the hot summer months). The mean summer temperature for these months is 30°C (dry bulb), with a maximum temperature of 43°C; the mean wet bulb temperature is 25°C with a maximum of 28°C. Mount Isa is located geologically towards the western edge of the Precambrian Shield of northwestern Queensland. This complex forms a north-tilting dissected peneplain which extends in the north-south direction for 640 km, with widths varying from 32 km to 190 km. The combination of differential erosion, regional strike, and steep dips has produced a corrugated topography of low north-south orientated hills and valleys. The field was first discovered in 1923 as a silver- lead-zinc field. Mount Isa Mines Ltd. was formed the following year and subsequently became the sole operating company on the field. Lead and copper ore have been mined and treated separately and simultaneously at Mount Isa since 1953. Intensive exploration commenced in 1954 and an active exploration program provided the justification for a series of production expansion programs in both silver- lead-zinc and copper (see Table 1 ). The most recent and largest production expansion program at Mount Isa commenced when a decision was reached in December 1969 calling for an increase in copper production from 100 000 to 150 000 t/y of blister copper. A major factor which influenced this decision was the substantial additions to the ore reserves in the so-called 1100 ore body which is a massive copper sulfide ore body with a known strike length of approximately 2500 m, a height which is variable up to 300 m, and a width of generally 300 m up to a maximum of 370 m (see Figs. 2 and 3). Host to the copper mineralization is a complex and variable rock generally called "silica dolomite." The ore body strikes 6.02 to 6.1 rad (345° to 350°), dips west between 0.78 and 1.13 rad (45° and 65°), and is truncated at depth by fault implaced basement rocks. It first occurs some 600 m below the surface and bottoms at about 1000 m below the surface. The unconfined compressive strength of the silica dolomite ore varies from 150 to 250 MPa, whereas the basement rocks, carbonaceous mylonite, slaty shale, buck quartz, and greenstone (a chloritic schist) are considerably weaker, varying in strength from 20 to 80 MPa. The distribution of mineralization within the ore body is variable, but can be considered as generally high grade at or just above the basement contact and diminishing towards the upper reaches of the ore body. The current

Jan 1, 1982

By James M. Johnson, David Landriault, Frank Palkovits

The term “Paste Technology” was first used in the late 1980’s. It was used to describe a high fines (15 wt% or greater minus 20 microns), low water content backfill material that could be transported underground through a borehole/pipeline distribution system (4” to 8” dia.) at a yield stress similar to fresh concrete (100 to 400 centipoise). This “Paste Backfill”, unlike slurry transported backfills does not segregate into separate solid and liquid phases at low pipeline transport velocities or upon disposal into the underground stope. Paste backfills can consist solely of fine material, or can include fines plus sand and aggregate similar to a concrete mix. Pipeline transport of paste requires that sufficient fine material (minus 20 micron content) is contained within the mix to lubricate the pipeline walls to create a plug flow condition. For concrete, the fine material is supplied through the cement addition to achieve high compressive strength. For paste, the fine material is generally available in large quantities in the form of mill tailings. The paste tailings can be transported underground for use as backfill or discharged on the surface in a tailings management facility (TMF). This natural abundance of fine grained material is not exclusive to mine tailings but is common to many waste streams in many different industries. This makes the disposal of many waste materials very amenable to paste pipeline transport and placement as a non-segregating slurry. The potential use of paste technology for a wider group of waste materials was realized by these authors and others over two decades ago. Through the effort of this small group the use of paste technology has expanded over the years to become recognized as a low cost, environmentally superior, and technologically controllable method of transporting and placing specific material waste streams with a low water content and high placement density. The high yield stress nature of a paste also lends itself well to the blending of one or more coarse waste materials into the fine waste material paste stream. This allows all the waste materials to be transported by pipeline, increases their placement density; decreases the supernatant release/treatment, reduces contaminant mobilization, hydraulic conductivity and oxygen/water reactivity through encapsulation in the paste matrix. The following paper describes the present state-of-the-art use of paste technology in the world today. It also describes future uses of the technology that are under development and speculates on the overall use of the technology for waste management in the future.

Jan 1, 2005

By J. W. Merks

Spreadsheet software is an effective tool for simulating dynamic stochastic systems such as mineral processing plants. The two-product formula is used to show how to set up a Monte Carlo simulation in a spreadsheet template and how to calculate variances of dependent variables. The key to a reliable and realistic simulation model is to obtain unbiased estimates for all independent variables and variances in the set that defines the stochastic system. Monte Carlo simulation is also a powerful tool for optimizing sampling procedures, for applying sensitivity analysis and for designing and evaluating experiments.

Jan 1, 2000

By Robert M. Dreyer

The first time that a geologist is confronted with the necessity of evaluating a lateritic ore deposit, he may feel that nothing could be easier. Why should there be any problems in making an economic evaluation of a relatively flat-lying, surficial ore body? After several hundred thousand dollars worth of frustrating work often culminating in a series of non-reproducible data - the evaluator may be a sadder and wiser man. This paper will try to illustrate why the evaluation of lateritic bauxite and nickel deposits is among the most difficult problems confronting an economic geologist - and, more especially, how this problem can be solved. Volumes have been published on descriptive and genetic studies of lateritic ores. Obviously, there is time today only for the briefest description of such an ore body. The laterite is a soil formed under tropical conditions and resulting in the concentration, within the soil zone, of certain tri-valent metals.- especially, aluminum and nickel. The soil zone is divided into two parts: (a) the true soil or lateritic zone and (b) the zone of, partially altered bed rock or saprolite. It is important to remember that, whereas bauxite generally is confined to the laterite zone, nickel deposits occur in both the laterite and

Jan 1, 1977

By K. F. Jakob

Sustainable development is a principle for the way we should act in the present. It ensures also options for the future to achieve a balance between social, economic and ecology development. The efficiency of raw material utilisation is being enhanced through technological developments, starting from extraction through all the following stages of the value creation chain. The use of domestically produced resources helps to assure the technological know-how. Additional indicators being collected and published by individual companies are questionable in countries with a tightly regulated legal framework such as in Germany, but make sense in developing and threshold countries. Sustainability in terms of efficient use of raw materials will manifest itself at the next stages of the value creation chain. Examples for efficiency improvement can be found in the steel, the power generation and agriculture industries. The approval procedures for German mining operations entail an internationally extremely strict assessment of the potential impact on the environment. All the mining activities include remediation and recultivation where the practise in Germany has become model character by international levels.

Jan 1, 2005

By M. J. Virnig, Peihao Qi, J. Brent Hiskey

The mechanism of gold uptake from iodide solutions by carbon has been investigated. Adsorption isotherms for gold and iodine were established. For activated carbon, approximately 300 mg of gold and 1000 mg of iodine were extracted per gram of carbon at maximum loading. Examination of loaded activated carbon particles by scanning electron microscopy reveals isolated patches of gold deposited on the carbon surface. High-resolution transmission electron microscopy shows that fine gold particles (1-4 nm diameter) are uniformly distributed within the carbon. Iodine was also observed throughout the matrix. The uptake of gold by carbon from iodide solution involves a combined reduction and adsorption process, where the gold iodide species is reduced to the metallic state superficially and adsorbed in the porous structure of carbon. A few experiments for the gold-chloride and gold-bromide systems were carried out for comparison.

Jan 1, 1993

By P. Soupios

Seismic geophysical methods have long been used by geologists and geophysicists to delineate subsurface features. These techniques work because different types and strengths of soil and rock transmit energy at different velocities. The Crosshole-Downhole tests (CH-DH) and seismic refraction survey (RS) are among the most used methods in engineering applications to obtain the elastic properties of subsurface layers. As a result, seismic methods have evolved into a cost-effective tool for rapidly determining depth to bedrock in engineering and construction projects. The seismic methods are best suited to sediment thickness analysis, bedrock quality determination and detection of the presence of weaknesses in the bedrock before the erection of any civil engineering structures such as bridges, tunnels, dams and portals. Seismic methods are also useful in estimating the rippability of bedrock ahead of construction. These methods are particularly useful for large-scale projects that require a significant number of drill holes, resulting in a substantial investment of time and costs for drilling. The CH-DH and RS methods are typically comparable in total cost to drilling, but provide significantly more information in 2-D and 3-D and therefore reduce the likelihood of conceptually oversimplifying the subsurface conditions. The above mentioned methodologies were considered to be the most appropriate geophysical methods for investigating the shallow structure and the dynamic soil properties of the area where the Ilarionas Dam is scheduled to be constructed. The main target of this work was to prove the potential of geophysical methods in providing accurate information to the civil engineer and to obtain information on the dynamic soil and rock properties for earthquake design analyses for the dam construction. Specifically, nine refraction seismic profiles and three cross-hole-downhole seismic tests were implemented to determine the subsurface conditions of the study area. The tests determined the shear and compression wave velocity profiles versus depth and other crucial parameters such as Young and Rigidity modules. Furthermore, they allowed the detailed 2-D mapping (along several profiles of the study area) of the subsurface variation of the soil and rock dynamic moduli.

Jan 1, 2006

By Gordon T. Clark, Stephen H. Gleaton

This paper discusses the conceptual design of cut-and-cover tunnels currently being considered as one of the replacement options for the earthquake damaged, elevated double-deck highway and seawall built in downtown Seattle 50 years ago. The 4.8 km (3 mile) long, 6-lane improvement consists of 1.6 km (1 mile) of at-grade roadway with aerial interchanges, 1.6 km (1 mile) of large two-level cut-and-cover tunnels along the Elliott Bay waterfront, and retrofit of the 50-year old, 1.6 km (1 mile)long Battery Street tunnel and north transition to grade. Construction of deep cut-and-cover tunnels, in complex glacial geology overlain by hydraulically placed fill immediately adjacent the existing sea wall, will require extensive use of concrete diaphragm walls, ground improvement and dewatering. The potential liquefaction and lateral spreading of the fill materials in this active seismic region pose significant design challenges and risk.

Jan 1, 2003