Search Documents

By L. Max Scott

[INTRODUCTION] The significance of gamma exposure to uranium miners has been recognized only in the last few years. Most ore deposits which have been underground mined, were 1% or less U308. Full-time mining of this grade ore can result in exposure exceeding 1 Rem per year. Several companies in Saskatchewan are planning to mine recently discovered ore bodies which contain ore pods in excess of 10% U308. The purpose of this paper is to present dose data which can be used to estimate gamma exposure from high-grade ore deposits, and to present mining techniques which will minimize miner exposure. [Dose Estimates] When one has a point source of radiation, the conventional laws of isotropic emission and the fall of dose with square of the distance, make dose calculations relatively easy. However, if one has an area source of infinite thickness, the assumption must be made that a uniform gamma flux is being emitted from all faces of the source (Figure 1). Dose from gamma emission would fall off only due to air attenuation up to such a distance at which the source can be considered to be a point source (usually 10 times the largest dimension of the source). For short distances, such as to the cab of ore-moving equipment, the dose reduction would be negligible. Assumptions: 1) Radium and gamma-emitting daughters are in secular equilibrium with uranium. 2) All gamma radiation is emitted from radium and its daughters. 3) Average gamma energy of 0.8 MeV. 4) Uranium ore has a linear attenuation coefficient of 0.212 cm-1, similar to that of Si02(sand). 5) Uranium ore density of 3.0 gm/cm3. 6) One curie of radium emits 6.84 x 1010 photon/sec(l). 7) One percent uranium ore contains 1 x 10-8 Ci/cm3 of radium. 8) Each MeV of 0.8 MeV photon results in a dose of 2.10[ ]10-3 mRem/hr. per MeV/cm2 -sec. 1) 9) Minimum ore depth 100 cm. 10) Linear attenuation coefficient instant for radium gamma of 0.374 cm -1 [ ] The photon flux from a radioactive slab is computed as follows: [Flux = photon/cm3 3(1) 2u S] [where, us is the linear absorption coefficient of s the source (uranium ore).] Thus, 1% uranium ore, in the form of an infinite slab, emits 1613 photon/cm2-sec, which results in a dose rate of 2.71 mRem/hr. Since the dose from an infinite slab is the same as a dose from an infinite radius right circular cylinder, the only correction needed from the above dose rate is for finite radius and point of dose above the end of the cylinder (Figure 2) [Dose = mRem/hr. {E2(bl) - E2(b3) - [(E2(b1sec[E] -E2(b3sec[E]]cos[O](1)]

Jan 1, 1981

By Ralph J. Anctil, James E. Palmer

According to relatively recent estimates by the US Geological Survey and the US Bureau of Mines, there are more than 0.9 Tt (one trillion tons) of remaining identified coal resources in the seven major western US coal-producing states and about 200 Gt (220 billion tons) in the demonstrated reserve base. Considering coal's current national production level of 0.7 Gt/a (0.8 billion tpy), these US reserve and resource figures are reassuring. Given here is a preliminary analysis of geologic constraints and an estimate of their effects on mining and recoverability of western coal. Mining Constraints USGS and USBM coal figures incorporate only thickness and depth, and are "blind" to many other major geologic constraints on mining and recoverability. The most important of these geologic constraints include: • coal seams too thin or too thick for conventional mining methods; • coal seams that cannot be mined due to insufficient separation from underlying or overlying previously-mined beds; • unstable or otherwise unfavorable roof strata; • soft or heaving floor strata; • coal seams that are too lenticular or discontinuous for conventional mining methods; • coal seams in intensely faulted areas; • coal seams having high angles of dip precluding the use of conventional coal mining methods; • coal seams that cannot be mined due to proximity of water-bearing strata; and • coal quality problems such as excessive ash, sulfur, chlorine, or sodium. Coal Thickness Present USGS-USBM classification for reserve base includes bituminous coal beds more than 0.7 m (28 in.) thick and subbituminous beds more than 5 m (60 in.) thick to depths of 305 m (1,000 ft). Both of these thicknesses are less than the thicknesses now considered mineable in the western US. The lower limit for bituminous steam coal in deep mines is about 1.5 m (5 ft). For subbituminous coal, a thickness of at least 2.4 m (8 ft) is generally required. Accordingly, the Bureau of Mines reserve base includes many thinner coal seams that will not be mined in the foreseeable future. Within the Powder River Basin of Wyoming and Montana many seams-Wall, Upper Pawnee, Lower Pawnee, Cache, Manning-range in thickness from 7.6 m (25 ft) to more than 30 m (100 ft) and occur at depths to 305 m (1,000 ft). These have been included in the Bureau of Mines reserve base. However, the mining technology required to mine these thick seams does not now exist. It will require many years for development. The ultimate recoverability from these thick seams is unknown, but could be as low as 25%.

Jan 8, 1982

By K. N. Han, J. J. Kellar, Y. Guan

The adsorption of zinc species onto silica in ammoniacal solutions was studied. The adsorption isotherms indicated that the adsorption of zinc increased with increasing pH. The adsorption density increased as the zinc equilibrium concentration increased up to =3.5x10-4 M. Above this concentration, the adsorption density was independent of the equilibrium concentration, and a maxima adsorption density was reached. Temperature had no significant effect on the adsorption density.

Jan 1, 1995

By Tomek Ulatowski

This article discusses four principal areas relevant to financing direct reduction facilities: (1) Lenders' differing requirements with respect to projected cash flows; (2) The impact of leveraging on project viability; (3) The importance of appropriate debt structure; (4) The significance of accurate and complete capital cost estimates. The overall findings emphasize the inseparable connection between the project economics and its financeability, and particularly how direcly intertwined they both are in the project planning.

Jan 1, 1978

By Brad Grothen

What is the most economical way of tunneling in mixed ground that may experience high pressures? Non-continuously pressurized, mixed ground Tunnel Boring Machines (TBMs) are being utilized to deal with a wide range of geology. Continuous improvements in these mixed ground machines allow for ever-increasing efficiency and reduction of project risk due to unexpected conditions. We will explore the performance of recent mixed ground machines throughout the world and then look at how new improvements to mixed ground machines will enable excavation of an expanded range of ground conditions. These conditions include mixed ground with low fines, mixed face rock, and fracture/fault zones with high pressures where in the past a Slurry TBM may have been utilized.

Dec 1, 2022

By Jeff Hussey

Since 1955, Gaspe Mines has produced 150 Mt (165 million st) of ore averaging 0.9% copper. The ore was mined from two open pits and from underground workings. In 1994, four exploration drill holes discovered a buried porphyry/skarn copper-molybdenum (Cu-Mo) deposit at depths of between 1,000 and 1,700 m (3,280 and 5,580 ft) below the top of Porphyry Mountain. The mineralization and alteration associated with the Porphyry Mountain quartz monzonite does not outcrop. Prior to 1997, about 19,500 m (64,000 ft) of drilling in 12 drill holes had outlined 200 Mt (220 million st) grading 0.73% Cu and 0.08% Mo. Mineralization occurs as veins and disseminations of chalcopyrite and molybdenite.

Jan 1, 1998

By Gabriel de Almeida

INTRODUCTION The widespread use of desktop computers by an ever increasing number of people, both for personal and for business and government uses, has brought public attention to surprising stories about computer abuse. Before the advent of microcomputers in the information processing environment, hundreds of amazing misdeeds involving large computers had already been reported, most of them perpetrated by highly skilled professionals. The undreamed enlarging of microcomputer potential has steadily posed a major threat to complex mainframe computing systems, as joyful teenagers become familiar with the habit of hacking around someone else's large processing system, by means of makeshift phone communication networks, based on their intended homework for personal computers -- for the sheer fun of it. Now, the never ending capacity and speed improvement of commercially available micros has given rise to a brand new concern for society: the hazards of processing sensitive information in the powerful, but still unsafe microcomputer itself, whether or not linked to other micros or mainframe networks. This paper deals with some aspects of the problems and presents some practical hints as to enhance protection and minimize risks to sensitive and secretive information when processed on microcomputers. The physical considerations of computer security and pertinent safety precautions will not be discussed, because while essentially relevant to information protection, recommendations are well defined by processing resources suppliers and their importance is more widely recognized by users in general. Definitions and Classifications. The following definitions and classifications will be considered in this report: Information Assets: Any knowledge or information processing, storing or conveying device displayed in one's environment. It consists of two main categories: INFORMATION RESOURCES: End user's application data wherever recorded. PROCESSING RESOURCES: EDP skilled user's hardware, software, peripherals, magnetic media, communication devices, auxiliary equipment, supplies and related operational procedures. Information Protection: In a broad sense this is the set of necessary procedures to assure to the legitimate user the effective control of the operation and allow modifications of information assets, so that their physical or cognitive integrity be preserved or any unexpected loss minimized inspite of accidental occurrences or intentional actions. Classification Processes: Commonly two classification processes are used to define key terms in information protection: SENSITIVE CLASSIFICATION: Pre-defined standards for assessing the vulnerability to losses due to lack of proper processing continuity if information is destroyed, disclosed, secluded, or misused. SECRECY CLASSIFICATION: A spectrum of degrees as to the expectancy of holding exclusiveness of unique information whose destruction, disclosure, seclusion or misuse will cause a negative impact on the legitimate holder environment. Sensitive Information: Any knowledge whose destruction. disclosure. seclusion or misuse - - - implies losses to its legitimate holder. It may be classified as: VITAL INFORMATION: An essential knowledge whose lack of proper availability implies total loss or termination of p

Jan 1, 1987

By J. D. Miller, C. L. Lin, J. Dong

Nano clay mineral particles such as kaolinite — with primary particles typically smaller than 2 μm in size — can cause significant problems in flotation processes and tailings disposal, including the processing of Florida phosphate rock and Canadian oil sands. In this study, the consolidated state of flocculated kaolinite sediment was examined, and high-resolution X-ray microtomography (HRXMT) was applied to describe the structure of the consolidated sediment. Using this tomographic information, the complex geometry of the channel network structure for the consolidated flocs was established for the first time. With the establishment of the experimental channel network structure, permeabilities were estimated by flow simulation using the Lattice Boltzmann method. Results for kaolinite sediment with and without polymer are compared and discussed. Results for flocculated kaolinite sediment in a gravitational field are also presented and discussed. The results show that as polymer dosage increases, the permeability of flocculated kaolinite sediment increases, and as suspension pH increases, the permeability of flocculated kaolinite sediment decreases.

By M. Misra

The processing strategy for the effective separation of bitumen from low grade (< 10 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1979

By Michael Ferrell

The primary reason pigments are used in plastics is to impart a desired color to the plastic. Color is one of the more important assign considerations associated with today&apos;s market oriented society. Secondary reasons for adding pigments to plastics include: 1. Improved UV stability 2. Enhancement to selected physical properties 3. Changes in optical properties Pigments may be used at loadings as high as 20% or as low as .001%. Generally the loading levels are between 0.2% and 2.0%. Pigments may be added to the plastic either by the manufacturer of the plastic, or by the user of the plastic. If the customer buys material that is already colored, it is referred to as "pre-colored". If the customer buys uncolored plastic and adds colorants, the process is referred to as "in-house" coloring.

Jan 1, 1985

By Trevor Riters

Advancements in Emerson’s instrumentation technology have brought value and efficiencies to the mining industry. Some think of instrumentation as basic sensors and valves, but with our solutions, we equip operators with real time, accurate, and reliable data that they can use to operate more effectively. Working with Caltrol, an Emerson Impact Partner, we successfully engineered wireless skids for a leach pad to provide precise measurement and control of raffinate solution to many of the large mine sites in Arizona.

Feb 1, 2025

By W. J. Adamson

Strategic Data Planning (SDP) is an emerging technique for the analysis and design of information systems. This paper describes the use of strategic data planning in the formulation of a complete integrated set of mining technical systems for the Koolan Island iron ore mine. Applications covered include hydrogeology, geology, mine planning, surveying, quality control, laboratory and mine production recording. Koolan Island is 13 kilometres long and 5.5 kilometres wide at its widest point. Its sole industry is an open pit iron ore mine of 3 million tonnes annual capacity, owned and operated by BHP Minerals. Some of the production is used by BHP Steel International, but most is exported. The orebody is steeply dipping and is mined bench by bench. Outturn grades for run-of-mine product are iron 66.5%, silica 3.0%, alumina 1.0%. Computer systems are run on Data General equipment, currently an MV10000. Computer applications, which are shared across mine sites, are developed and maintained by BHP Information Systems in BHP&apos;s Melbourne Office.

Jan 1, 1986

By M. N. Herrera

The bioleaching of mineral sulfide pulps in a bench-scale rotating drum reactor has been studied. The reactor includes horizontal paddles in the inner wall for lifting of the mineral pulp. The performance of the reactor was tested in the bioleaching of a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans strain (ATCC 19859). The concentrate was efficiently bioleached at 50% pulp density with the drum operating at 0.5 -1.0 rpm Attempts of bioleaching the concentrate at the same pulp density in conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows to operate at much higher pulp densities than the conventional stirred tank reactor. This behavior is explained in terms of an improvement of the bacterial activity due to a better control of the attrition of the mineral particles.

Jan 1, 1997

In early March 2011, a 6.2 m (20.3 ft) diameter Rob-bins Double Shield tunnel boring machine (TBM) crossed the finish line in Sochi, Russia. The machine completed a 4.5-km- (2.8-mile-) long section of tunnel that will ultimately become part of the transportation infrastructure for the 2014 Winter Olympic Games. The TBM advanced through difficult ground at aver-age rates of 100 to 120 m/week (330 to 390 ftpw) for contractor OJSC Bamtonnelstroy, a division of the SK Most Company. The section of tunnel will ultimately become a service tunnel for Complex #3 - a section of Sochi?s transportation infrastructure under construction, which includes road and rail tunnels. A second, 10 m (32.8 ft) diameter Robbins Double Shield TBM is currently excavating the parallel 4.6-km- (2.9-mile-) long main railway tunnel using a continuous conveyor system for efficient muck removal. A 13.2 m (43.3 ft) diameter highway tunnel is also under construction. The 6.2 m (20.3 ft) Robbins TBM achieved high rates despite difficult conditions. The tunnels run through mixed ground including massive to completely fractured limestone with clay seams. Some sedimentary rock including sandstone and siltstone is present, along with fault zones consisting of breccias and conglomerates. In May 2010, the machine was stopped after encountering a significant fault zone consisting of broken rock and running soft ground. Field service personnel and crew successfully freed the machine by excavating a bypass tunnel around the TBM, freeing the cutterhead. Following the restart, a combination of continuous probe drilling and ground treatment with cement silicate and foam kept the machine moving forward.

Jan 1, 2011

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The acoustic emission (AE) technology has a high potential for flow characterization in hydraulic transport processes. For instance, in deep-sea mining, there are applications where manganese nodules are transported from the bottom of the sea to the surface or a transport ship. Here, an AE-based flow characterization system plays an important role to avoid the transport of non-related objects. However, the structural materials for the components of this system must be carefully selected to ensure resistance against corrosion and a good AE signal transmission. Therefore, in this experimental study, we evaluated the AE attenuation behavior of four different materials that can be employed in marine environments due to their properties. The results were obtained using thin plates and they indicate which materials have the highest and lowest attenuations. Moreover, we provide insights regarding the different wave modes that propagate on the plates.

Mar 2, 2023

By William Gleason

The evolution of technology has made the world a more connected place. It continues to change the way we power our homes and vehicles and is leading to a future that seems to be limitless. Limitless as long as we can continue to supply the minerals necessary for technology to produce better iPhones, more efficient electric cars, better wind turbines and sophisticated national defense systems. These minerals, dubbed critical minerals, have surged in importance in every corner of the world and, on Aug. 3-4, they were topic of conversation at the Critical Minerals 2014 conference in Denver, CO. The conference, hosted by SME and the Australasian Institute of Mining and Metallurgy (AusIMM), looked at critical minerals from every angle, from where they are found to what the future might be. Among the minerals that have been called critical are rare earths, a collection of 17 minerals that have become increasingly important as technology continues to advance in everything from communications to energy to national defense. Leading off the conference, David Abraham, senior fellow at the Institute for Analysis of Global Security, explained that, like many people, he is relatively new to rare earths. Unlike most people, though, Abraham developed more than a passing interest in the minerals and has since travelled the world to understand the role of rare earths ? where they are found, how they are mined, how they get to market and, eventually, what applications they are used in. Following his travels, he said he returned concerned about the sector and how the industry will keep up with the demand that only seems to be growing in the modern world. And, Abraham noted, that it is not just the developed world that is driving demand. It stretches even to places like Indonesia, where the average annual income is about $3,000/year. Yet, the nation is one of the most active places in the world for social media with a population that is wired in with all kinds of electronics. The problem facing the sector is, and has been for a long time, and especially since 2010, supply of the minerals. At one time, China produced about 98 percent of the world?s supply and controlled the sector completely. In 2010, as the world began to demand more rare earths and develop other sources, China announced an export ban on rare earths. This changed the game completely, from the production lines all the way to the floor of the U.S. Congress.

By Paul S. Murphy, Eric W. Oehrke

INTRODUCTION The global market for sulphur has experienced dramatic structural shifts during the past 10-15 years. After a number of years of dominance as sulphur suppliers, the world&apos;s Frasch producers were confronted with large increases in nondiscretionary sulphur production from sour crude oil and gas, while escalating energy and exploration costs reduced the economic incentives to replace dwindling sulphur reserves. Sulphur demand also experienced substantial growth, but the majority of this increase was filled by nondiscretionary production. The result was essentially flat demand for Frasch sulphur during this period. This paper briefly summarizes Freeport Sulphur Company&apos;s outlook for global supply and demand for sulphur through the year 2000, and examines in more detail the history and anticipated shifts in trade patterns. World trade in elemental sulphur (brimstone), despite year-to-year fluctuations, has been on an upward trend in recent years, and should continue to grow through the end of this century. The type (discretionary vs. nondiscretionary) and location of forecast sulphur supply sources has potentially broad implications for the world&apos;s Frasch producers, as they compete in a world market which is increasingly supplied by non-discretionary production. SULPHUR DEMAND Sulphur is a versatile and essential element used in a wide variety of manufacturing processes. Almost 90% of world sulphur consumption is in the form of sulphuric acid. The relatively low cost, ready availability, and physical and chemical properties of sulphuric acid make it the most economical acid for a number of chemical processes. Although sulphur is used in the manufacture of many products, the largest consumer by far is the phosphate fertilizer industry. The majority of sulphur demand growth over the past 30 years has occurred in this area, and today it accounts for nearly 65% of global sulphur consumption in all forms. Due to the relative importance of phosphate fertilizers, sulphur demand is typically discussed in terms of fertilizer and non-fertilizer (or industrial) uses, and this approach will be followed here. We at Freeport believe that global consumption of phosphate fertilizers should grow at an average annual rate of about 3.5% through the year 2000, which is roughly equal to the growth rate experienced during the past ten years. The basic assumption underlying this forecast is that world population will continue to grow significantly, while the total acres of cropland will grow only slightly. Therefore, in order to feed a growing population, higher crop yields will be necessary, which in turn will require the increasing use of fertilizers. This expected growth in phosphate consumption will, without doubt, fluctuate from year to year, and we Frasch producers have painful memories of the large dip in demand during 1982-83. However, we believe that the fundamentals for growth are very good, and that future demand will move back onto the historical trend line. In the recent recession the use of sulphur in the non-fertilizer or industrial sector dropped sharply, and it now appears that future growth will not return to the old trend line. Most of the non-fertilizer uses of sulphur and sulphuric acid involve older industries which are very mature, such as oil refining, steel, pulp and paper, pigments, etc. The use of sulphur in some of these industries is expected to exhibit little or possibly even negative

Jan 1, 1986

By Sadatoshi Ohmori, Karen Shinoda, Nobuharu Isago

Method of tunnel excavation is generally classified such as full-face excavation, bench-cut excavation, diaphragm with center pillar excavation, center drift advancing excavation and so on. These excavation methods should be selected properly in terms of ground condition, the area of tunnel section, the arrangement of construction. Center drift advancing excavation method in mountain tunnel construction, is often applied under quite weak ground condition, prior to the main tunnel widening excavation. Recently, the advancing drift is for the excavation of extreme larger section in main tunnel to confirm the stability of face. In addition, we make advancing deformation occur in drift when the construction was done in poor ground like squeezing and swelling ground, and the force occurred in main tunnel was expected to reduce by the effect of ‘dodging’ for support structure. Mechanical relation between drift and main tunnel has been mainly grasped on past experiences in Japan. However, the characteristic of tunnel enlargement was partially discussed by using the three dimensional analysis and the result was grasped by past experiences on the basis of each tunnel construction. It is considered that the natural ground stress is normally released as the advance displacement, but it was released after the main tunnel widening, causing a displacement and deformation increase. Up to now, the construction practice has shown the reduced displacement during the main tunnel widening excavation by the drift, and the numerical analysis agreed with above observation. However, there is no report found that the displacement and deformation at the time of widening excavation of the main tunnel become larger in case of a drift application. In Kyusyu area, western part of Japan, the northern part of Yoshinomoto tunnel was applied an advancing bench-cutting method for a center drift for the purpose of obtaining the geological information for support selection of the main tunnel in widening excavation. The shape of center drift was a perfect circle with a diameter of 4.0 m or 6.0 m and the same temporary support regardless of the geological situation. As a result, the displacement and deformation of the main tunnel after widening excavation were larger than the section where the center drift was not applied. Furthermore, the displacement and deformation of the main tunnel after its widening excavation was considered larger in the section where the cross-section of the center drift with 4.0 m diameter was applied than one with 6.0 m. Therefore, the center drift with a high rigidity support structure had the effect of suppressing the advancing deformation prior to the main tunnel widening excavation.

Jun 13, 2021

By Marini David, Pigorini Andrea, Fuoco Stefano, Zurlo Raffaele

"The excavation of a tunnel in highly weathered and strongly fractured rock masses due to tectonic actions is still a challenge. In order to maintain reasonable productivity, excavation through a wide zone of highly tectonized rock mass requires a detailed, integrated study of the construction solutions and a monitoring system to minimize the process time and to optimize the adopted consolidation measures in accordance with a predefined matrix of possible support systems. This paper summarizes some interesting data acquired during the excavation of the Brenner Railway Base Tunnel system between Italy and Austria. The Brenner Base Tunnel (BBT) runs through the fault line between the European and the African tectonic plate. This big fault zone is called “Periadriatic Line.” In particular, data acquired in the exploratory-service tunnel have been analyzed. Furthermore, the base concepts for defining the consolidation and support solutions adopted for the excavation of the exploratory tunnel are described. INTRODUCTION The Brenner Railway Base Tunnel (BBT) is a system of underground structures and tunnels that is designed to connect Italy and Austria using new railway standards. It is based on high speed (HS) concepts and applies the European Standards for Interoperability (TSI). The railway includes twin tunnels for a total length of about 55.0 Km without considering the connection tunnels to the existing underground railway in Innsbruck. Including the latter, the total length of the tunnel system reaches 64 Km, and is among the longest tunnels in the world. The Italian section passes through the so-called ""Periadriatic Line,"" which is an important tectonic structure generated by the collision between the European and the African tectonic plates. Despite the extensive investigations carried out (boreholes down to 700 meter depth), significant geological and mechanical uncertainties inside the Periadriatic formations remained unsolved. In order to elevate the level of confidence and observe the behavior of the rock mass at a representative scale, the BBT Authority decided to excavate in advance the service tunnel, which has taken the function of an exploratory tunnel. The data and observations collected during its excavation would provide important insights for the design of the main tunnels."

Jan 1, 2016

By William R. Groseclose, Cecil E. Tackett

Since 1965 when the first mole was used on Bureau work, the Bureau of Reclamation has completed 17 tunnels of over 5,000 feet in length. The longest was 12.8 miles. Total length of the 17 tunnels was 376,207 feet, or over 71 miles. The finished diameter varied from 7 feet 0 inch to 18 feet 0 inch with 82 percent (58 miles) being less than 12 feet 0 inch in diameter when lined. All of these tunnels except one are gravity flow, water conveyance tunnels with relatively flat gradient. One is a low-head pressure tunnel. All were constructed by contracts resulting from fixed-price bids. Starting in 1964 the Bureau of Reclamation initiated the practice of giving several options in the specifications on methods of tunnel excavation. Since that time, construction work has been completed on 17 tunnels. Of this number, 11 were mole excavated and 6 were excavated by conventional drill and blast methods. In general, there has been 2 feet of mole excavation for every 1 foot of drill and blast. Cost comparisons are based on only 13 tunnels because the Bureau has 4 recently completed tunnels that have pending claims; therefore, final cost data are not available. Some definite trends show from the data available; however, the number of completed tunnels in some categories is so small the results cannot really be considered a trend. As more data become available, the indications will become more reliable. The information is presented to indicate general trends and comparisons and cannot be meaningfully used for a one-on-one comparison because of individual tunnel differences not considered.

Jan 1, 1974