Search Documents

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities, or 82 percent, may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible.

Jan 1, 2016

By Steven E. Mischler, Jay F. Colinet

The Mine Safety and Health Administration (MSHA) promulgated a rule in 2014 that required numerous changes in compliance dust sampling requirements for coal mine operators. Two key parts of this rule were the lowering of the respirable coal mine dust standard from 2.0 mg/m3 to 1.5 mg/m3 and requiring operators of underground coal mines to use a continuous personal dust monitor (CPDM) for compliance sampling. The CPDM currently approved for compliance sampling is equipped with a display that provides miners with in-shift information on their respirable dust exposure. The goal was to provide an indication of a potential overexposure and empower the miner and mine operator to implement changes in controls and/or operating practices to prevent an overexposure from occurring.

By James Carroll, Lance Heyer

This paper describes the shaft design and construction for a 72-inch microtunnel under 14 active railroad tracks in Avondale, Louisiana. Initial shaft design for a deeper tunnel alignment considered secant piles with a jet grout plug. Final design for a shallower tunnel alignment included contractor input with support consisting of braced sheet piles with a jet grout plug. The authors further elaborate on jet grout implementation in very soft organic clay soils and the practical limitations of jet grouting. This paper emphasizes how all project participants worked together to utilize value engineering and alternative delivery on a unique tunneling project with a focus on temporary shaft support.

Jun 23, 2024

By Om P. Garg

The purpose of this paper is: 1) To summarize the capabilities and some of the limitations of the existing mine planning software. 2) To provide some guidelines for acquiring the software. 3) To identify problems and challenges in terms of how to justify increased use of computers (particularly the 32-bit microprocessor based super micro computers), for various activities related to a mining operation No attempt has been made to review the contents of available software packages in detail. Also the scope of this paper is limited to mine planning related computer applications. Applications related to accounting, inventory control, preventive maintenance, equipment scheduling, etc. have not been covered.

Jan 1, 1983

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

"The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities (82%) may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis. Among coal and rock dust exposure, high noise levels, roof and rib falls, and the potential for fires and explosions, operating and working with heavy machinery poses a significant risk to miner safety. One of the most hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 39 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are now required on all operating CMMs in underground coal mines with the exception of full-face CMMs [1]. Commercially available proximity detection (cPD) systems are based on the principle of magnetic flux density (B-field). Typically, four magnetic field generators are positioned on a CMM, and personal alarm devices (PADs) are worn by the miners that detect magnetic flux density difference. As a miner wearing a PAD gets closer to the machine, the flux density increases. Zones can be constructed around the machine so that an alarm will trigger on the PAD based on the flux density."

Jan 1, 2016

By Wei Zhang, Jinhong Zhang

An atomic force microscopy (AFM) image analysis has been applied to study in situ the adsorption of hydroxamic acid collector, i.e., octanohydroxamic acid (OHA), on malachite in aqueous solutions. AFM images show that hydroxamic acid collector adsorbs strongly on malachite mainly in the form of insoluble copper hydroxamate complex. Increasing the collectors’ concentration and the adsorption time both increase the adsorption of hydroxamic collectors on malachite. Results from the attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that the collector adsorbs strongly onto malachite, with strong absorbance spectra being detected, and the ATR-FTIR results confirm those as obtained by AFM. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of malachite. The findings of present study also show that AFM image analysis is a powerful tool for the study of the hydroxamic acid collectors’ adsorption on malachite surface and it can help with the development of novel collectors for malachite flotation.

Feb 1, 2025

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral-processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. When a sensor goes off calibration, it results in errors that can have a severe impact on plant economics. Classical statistical approaches fail to detect when errors are “subtle,” unless they grow and become large enough to be “gross,” whereas methods based on signal processing and artificial intelligence fail in dealing with the complexity of process fluctuations. Due to the sheer volume of sensors, undetected errors are not remedied until the next calibration, which on average are a year apart across all industries [1]. This research aims to detect such subtle errors (2 percent bias) in shorter time spans of about a month — rather than wait for errors to grow — using innovative data-mining techniques and algorithms.

By Stanley M. Moos

In reviewing available vacuum filtration equipment in this paper, several types of filters have been included which are probably not familiar to operators in the mining industry. However, it was felt that these units might be of interest in the event that an application should arise for the filtration of a product in the future that does not exist today. In addition, exposure of our industry to equipment used in other industries might have a tendency to be thought provoking and perhaps lead to the development of equipment and/or applications in our industry which do not necessarily exist at this time. Most innovations in filtration equipment have been confined to the improvement or design change of components and accessories, particularly reflecting the availability of materials of construction that have been developed. Recent developments in the application of horizontal belt filters have been innovative. The application of this unit as a substitute for or an adjunct to thickeners in a CO circuit can certainly be innovative and perhaps provide a basis for reduction in capital and operating costs in this area. For example, mill tails are generally pumped at the highest possible density that will adequately flow. Tailings ponds and dams with their attendant design requirements are based upon this estimated water volume. Availability of a much dryer, non-flowing filter cake opens up several new options for disposal. Considerable cost savings could result in the design and planning of disposal areas for containing dryer material. . No attempt has been made in this paper to provide a manual for the operation of all of the many types of equipment that are available. Rather, the paper tries to present an overview.

Jan 1, 1978

By Thomas F. Clemens

This paper covers various changes in government regulations, taxation, and legislation for the past two plus years and the up- coming one. Part of the paper will discuss recent business conditions and how they have affected the cement and lime industry.

Jan 1, 1983

By Peter J. King

Demand for both lead and zinc to the year 2000 will be characterised by modest to nil growth in mature economies, with positive 3 to 4 per cent annual growth rates in developing nations. Asia and China will feature significantly in this growth. Overall lead demand is expected to grow about 1 per cent a year, with industry becoming more dependent on the fortunes of the automotive industry as the lead-acid battery will be the only major end use to expand. Zinc will become more dependent on its main use, galvanising, as the automotive and construction industries move to high levels of dependence on corrosion prevention. Strong growth in zinc consumption in S.E. Asia, China and India is likely to feature widespread development of the continuous steel strip mini-galvanising line technology. Thank you Mr. Chairman for inviting me to this Conference. As an Australian I am honoured to be here to offer some thoughts about future trends in metal consumption -- with particular reference to the role of countries in my own neighbourhood, the developing Asian nations, including China. It is customary for a member of the producer fraternity to speak to the topic of future development. This is no doubt due to the fact that our companies are so often engaged in endeavours to determine the future prospects of the metals as essential background to massive investment decisions relating to the development of new mines and smelters. This is sometimes also applied in relation to the more painful decision of closures of aging operations. In this paper I have drawn upon recent studies by AM&S into the future of lead and zinc. While this work has been thorough and skillful, we are nonetheless left with uncertainty on a number of counts. Firstly. predictions in the past in our industry have not been all that credible. Need I remind a U.S. audience for instance of the Paley ' investigation setup by President Truman in 1950 to study U.S. copper requirements for 25 years in the future. Asarco's Simon Strauss gave those of us daring to forecast long term commodity trends a salutary reminder that the Paley Commission with all the expertise at its disposal missed the mark in its copper predictions by a very wide margin indeed. Additionally, it is difficult to take comfort from longer term economic forecasts. Too many important economic issues remain unresolved suggesting considerable caution. These include the threat of growing protectionism; low economic growth rates with stubborn unemployment levels; and levels of government expenditure at near saturation as a percentage of GDP, to name a few. However, on a more optimistic note. we can look to China, where there appears to be momentum in its economic growth; oil, where stable oil prices to the mid 1990's will contribute to inflation control; and the fact that LDC debt, while still a major issue, is declining in importance and priority. In the short time allocated to us. I wish to deal succinctly with the lead and zinc raw materials supply picture, which is one I do not believe will hold too many surprises for this audience. Following the review of raw materials supply, we will turn our attention to the changes in the pattern of demand towards the year 2000. emphasising the Asian position. In this context. I would like to focus on the theme of the changes in OECD consumption levels relative to those of the emerging nations. One area we will be paying special attention to is China.

Jan 1, 1986

By Ulrich Maidl, Jamal Rostami, Ulf Gwildis

Tunnel Boring Machines (TBM) have more or less become the preferred method of tunneling in various ground conditions and Programmable Logic Controllers (PLC) or microprocessors are standard features on TBMs to monitor and record various sensory systems on the machine providing the possibility for machine automation and control. The data collected from these sensory systems and channeled through PLC is stored for real-time analysis or use by the operators. Based on typical construction specifications, part of the information collected in the process is shared with the project management team representing the owner. Machine data automatically acquired during TBM advance is typically processed by specialized software to offer the project team data visualization and evaluation options. Interfacing with Geographic Information System (GIS), Computer-Aided Design (CAD), 3-D geologic model, instrumentation data bases, and Document Management Systems (DMS) allows for developing Building Information Models (BIM) of the tunnel’s as-built condition. Application of Artificial Intelligence (AI) processes such as Machine Learning (ML) have already been used for analysis of data, including performance prediction of hard rock TBMs, and exhibited the potential of big data analytics in improving the productivity of the operations. This paper outlines anticipated disruptive technological advances with implications on geotechnical exploration, TBM operation, face condition tracking, subsurface risk allocation, and claims management in the future.

Jun 13, 2021

By M. S. Klima, A. Simard, M. L. Turek

Laboratory testing was carried out to evaluate several devices for recovering clean coal from bituminous coal refuse material. The bulk of the testing focused on using a dense-medium cyclone to process -0.6-mm refuse material. A hindered-settling column and a spiral concentrator were also used to process nominal 1.2 x 0.15-mm material. Product yields and ash contents were obtained for all tests, while partition curves were generated for selected tests from which the characteristic performance parameters (relative density of separation and probable error) were determined. The results indicated that the dense-medium cyclone was capable of cleaning down to 0.037 mm, while the other devices were effective to 0.15 mm. Keywords: Coal recovery, Coal refuse, Dense-medium cyclone, Hindered settling, Spiral concentration

Jan 1, 2003

By C. S. Simons

The aphorism that provided the title of this paper is probably a couple of hundred years old, but it still expresses a fundamental truth in the metals industry. This truth will be illustrated through a brief review of the major developments in the extractive metallurgy of the oxidized ores of nickel - the "laterite" ores. While the details to be discussed are for the most part specific to nickel, a close parallel with other commodities - particularly in recent years - will be apparent even to those whose interest in nickel itself is slight. Thus it is hoped that this paper will be stimulating, at the least, to anyone who is concerned with the implementation of process improvement, "Invention" in the present context means any change from "conventional" process technology that shows a reasonable chance of reducing costs, increasing revenues, or both, in the production of a commodity. This can be anything from a simple rearrangement of flowsheet steps to a completely different basis for processing. And the result may reduce costs by more efficient use of energy or labor or reagents; may increase revenues by better recovery of the primary product or by introducing the recovery of previously ignored by-products; may insure sales volume (and thereby cash flow) through higher product purity or an improved product form. "Necessity" is the perceived need to attain at least one of these classes of results. This perception of necessity, however, varies widely from management to management and from project to project.

Jan 1, 1983

By Jerry C. Tien

The rare earth elements (REEs) are a group of 17 chemical (metallic) elements which appear in the periodic table. The group consists of 15 lanthanide elements along with yttrium and scandium (Table 1). They share many similar properties, which is why they occur together in geological deposits. Although commonly referred to as rare, they are really quite common; the reason they are perceived as rare is because it is not common to find them in commercially viable concentrations. These metals are critical to advanced technology, ranging from smart phones to global positions system (GPS) receivers, medical devices and jet engines. They are critical in green, high-tech and defense industries (Fig.1 and 2). Although there have been increasing efforts to find alternative supplies, these efforts have been complicated by the pollution that rare earth mining and processing creates. To extract rare earths minerals from mined ore is a complicated and costly process. The ore is first mined through normal mining process, the bastnaesite, which generally contains a number of minerals of little value, is first removed through a floatation process. The bastnaesite containing the REEs is further separated into their respective pure forms in a separation plant using acid and various solvent extraction separation steps. Each element has its own unique extraction steps and chemical processes. At times, these elements, in the form of oxides, will require reprocessing to achieve ideal purity. The last steps would be to further process into metals first, then alloys for various applications. The entire process takes approximately 10 days. The mining and processing of REEs, if not carefully controlled, can create environmental hazards. This is one of the reasons the Mountain Pass Mine in California was closed down in the 1980s.

Dec 1, 2013

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport's Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1'8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987

By F. Qiming

By means of flotation experiments, potential-pH diagram, electrochemical testing and X -ray photoelectronic spectrum (XPS), the main factors (the thermodynamics and the property of surface products) influencing the separation of sulfide minerals (such as galena and chalcopyrite) in the collectorless flotation are studied. The actual conditions (Eh, pH) of separation are not conformable to the results of thermodynamic calculation. The kinetic behavior of oxidation of sulfide minerals and the property of oxidation products are the decisive factors of the separation of sulfide minerals in the collectorless notation.

Jan 1, 1992

By George Fumich

The Office of Coal Research has been supporting the development of processes for producing synthetic pipeline gas from coal since 1964. .Some of this work has also been jointly supported by the American Gas Association. The work has progressed through laboratory investigation, to bench scale, to pilot plant. It was far from a crash program, generally being fund-limited.. As of one year ago, we had reached the following position: 1. The Institute of Gas Technology HYGAS. process pilot plant in Chicago, Illinois, was in the process of being finally completed. This plant is designed to produce about 1,500,000 cubic feet of pipeline-quality gas per day from 75 tons of coal. 2. The Consolidation Coal Company, CO2 Acceptor Process pilot plant in Rapid City, South Dakota, was well._ on its way to completion. This plant, designed primarily for lignite and subbituminous coals, has about one-half the design capacity of the HYGAS plant. Additionally, the initial construction did not provide for cleanup and methanation; only the preliminary synthesis gas is produced. 3. The Bituminous Coal Research, Inca, BI-GAS pilot plant was in a preliminary design stage. A site had been selected near Homer City, Pennsylvania, to build this plant, planned to consume 120 tons of coal per day. Meanwhile, as you are all well aware, a natural gas shortage was developing in this country. Much has been published about it, so I will not. bother you with further details. Suffice it to say that the reserve-to-production ratio has been steadily declining, because we have been using.-as-faster than we have been find-

Jan 1, 1972

By E. Neumann

With fuel costs unstable but escalating, solid fuels are playing an increasingly larger part in industrial concerns. Coal, petroleum coke and wood are examined from a burner system design viewpoint and from operational experience in kilns, hot gas generators, etc. The burner of today must also handle multi-fuel tasks and allow immediate, painless switching from one fuel to the next as well as the simultaneous burning of two or mope fuels. The paper discusses the principle of burning alternate pulverized fuels as well as the practice both in the United States and around the world.

Jan 1, 1983

By Diler Katircioglu-Bayel

The effects of the operating parameters of media filling ratio, solid mass fraction, grinding media size and grinding time on the stirred media milling of talc were studied. The findings were assessed based on the product particle size (d50, d10), surface area (Sw) and energy consumption (Em). Furthermore, after determining the optimum grinding conditions, Box-Behnken statistical design was used to determine the effect of parameter interactions on the d50 size. The media filling ratio significantly affects d50 size decrease compared with solid mass fraction and grinding time. The minimum d50 size was also achieved under optimum grinding conditions.

By Roger G. Rowe

The Crandon deposit, located in northern Wisconsin, is a 65.8 million ton Precambrian volcanogenic massive sulfide deposit which averages 1.4% copper and 5.8% zinc. The deposit is classic in origin, mineralogy and shape. Comprehensive understanding of the geology of both the deposit and the project site has been fundamental to the credibility and success of Project feasibility studies and regulatory permit preparation. Mine development in the current investment and regulatory climate requires thorough and timely application of geologic tools. From 1977-1980 geologic activities were focused on the typical objectives of orebody delineation, reserve estimation, depositional geology, and general site investigation. Results from these programs formed the basis for the Project's preliminary feasibility studies. Since 1981 further geologic investigations have provided criteria for project design, site management, and operational permitting. Activities have included mine entry position definition drilling, developing geostatistical reserve modeling, large diameter (150 mm) core drilling for mill pilot samples, rock mecha¬nics testing, and evaluation of the glacial overburden/deposit geohydrology for computer simulation.

Jan 1, 1983