Search Documents

By Pedro Pablo Vasquez Coronado, Victor Octavio Tenorio

"Productivity in openpit mines depends on the observation and adjustment of critical phases of operation. As one of the most expensive activities in openpit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad hoc methodology for analyzing the key performance indicators (KPIs) involved in the production cycle, it is possible to compare actual performance and ideal operating conditions and develop an alert system when operating conditions are subpar with the expected production standards.Study objectivesThe purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle, or when the time of completing production tasks is falling outside a predefined value. This alert is compared with predefined KPIs and is used to determine corrective actions.The alert will:• Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process.• Demonstrate the utility of KPIs in the extraction of ore and waste and how they help to identify equipment performance.• Develop software interfaces to visualize the alert system in order to increase awareness in the operations supervisor.• Make recommendations for future applications that can help improve the productive process of an openpit mine.Problem statementTransporting material in openpit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity while subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded and other delays. This creates inefficiencies in fuel consumption and energy utilization.For the identification of delays, a contextbased system could be required in order to help optimize the haulage cycle time by controlling delays in loading, haulage and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2015

By S. Chander

The results of an investigation to characterize the chalcopyrite/solution interface are presented. Several techniques including galvanostatic and steady state polarization, cyclic voltammetry and impedance spectroscopy were used. The results show that the dissolution of chalcopyrite is incongruent. Initially, at low potentials(<O.34V), iron species are released which give rise to the growth of an iron-deficient sulfide (IDS) layer. The dissolved iron might reprecipitate as a hydroxide layer depending on solution composition. Continued oxidation involves diffusion of species through the product layer. At higher potentials (>O.48V) further oxidation leads to dissolution of copper and sulfur species with a resultant breakdown of the IDS layer. The changes in properties of surface coatings resulting from various electrochemical treatments are discussed.

Jan 1, 1991

By Brij M. Moudgil

Separation of dolomite from apatite, because of nonselective adsorption, cannot be achieved by conventional froth flotation technique. Results obtained in the present study also indicate, that this can be attributed to the depletion of the collector molecules due to complexation with the calcium and magnesium ions, dissolved from the two minerals. However, it has been established in this investigation that conditioning the material at pH 10, followed by reconditioning, without any additional collector, at pH 4, results in selective flotation of dolomite from the mixture. The recovery of apatite, in the proposed reconditioning process, is much higher than with the conventional conditioning under similar pH conditions. The mechanisms involved in the conventional conditioning, and the reconditioning process are presented.

Jan 1, 1983

By J. Driscoll, T. Morson, Ross M. Workman

The study investigates the effectiveness of the canopy air curtain (CAC) in reducing respirable dust exposure for shuttle car and ramcar operators in underground coal mining. Field testing showed that the CAC reduced dust exposure by 11-34% overall and by 57-65% during ramcar loading by the continuous miner. These results demonstrate the CAC’s potential as a significant dust control device.

Feb 19, 2022

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014

In this paper, we present design and implementation details of a fuzzy-behavior-based controller for an automated excavator. This robotic excavator must be equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered from bucket mounted force sensors during the excavation process. Implementation details and experimental results using the fuzzy behavior based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining excavator controller.

Jan 1, 1996

By S. B. Bhagwat

The United States has abundant coal resources that could last at least another century. and probably longer at present consumption rates. Geographically, the coal resources are distributed over the entire nation including Alaska, although there are no coal deposits in the highly populated areas on the two coasts. This allows free access to the coal, but makes transportation more expensive. Not all coals can be utilized equally because they differ vastly in quality. The sulfur content of coals, considered as the most detrimental acid rain-causing element, varies from as low as 0.3 percent in some areas of the western U.S. to 5 percent or more in parts of the Midwest. The chlorine content, which causes corrosion of plant hardware, also varies regionally. The 1990 amendments of the Clean Air Act of 1963 (CAA) require that emissions of sulfur be restricted and rolled back in two stages by the year 2000. There have been a number of reports expressing concern about the future of the industry in the states where high sulfur coal is produced. The remedies devised by the federal government and many coal-producing states in the past to "se-cure" the future of the regional coal industries have focused on the physical task of removing sulfur rather than the economic challenge of doing so at a cost that will enable high-sulfur coals to survive and compete. The past remedies, generally, were not specific enough to account for the characteristics of regional coal deposits and did not look at the coal market as an integrated national and international entity. The State of Illinois has, in recent years, taken a more comprehensive approach to the solution of the problem.

Jan 1, 1992

By Lauren M. Roberts, Ralph R. Sacrison

Pipeline or borehole free-fall transfer of material has long been done in support of underground mining. This paper addresses some characteristics and design elements in selecting systems suitable to the transferred media and the mine requirements. Though aspects of overall systems are discussed, principal attention is directed to the slickline/dropline/transfer line and the discharge diverter/rockbox/energy dissipator/boot. These terms are common to these systems, often used interchangeably, and will be used as appropriate to the material, equipment and construction. Following several design sections, fabrication and construction, and system operating and maintenance procedures are discussed.

Feb 1, 2025

By Mark E. Gershon

Extensive efforts are under way to- ward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1985

By Z. Yunquan

The flocculation and dispersion behaviors of microsize wolframite and quartz are systematically studied in this paper. For synthetic mixtures, the floc separatory method on gravity units--electromagnetic vibration table (EVT) and lifting column (LC), have been approached. Satisfactory results can be obtained with a weak shearing. A better metallurgical performance can also be achieved for natural ore slimes through the combined technique. The efficiency is better than that of single gravity separation. Finally, the mechanism has been investigated.

Jan 1, 1990

By T. V. Ramey

Heap leaching in certain parts of the world, such as Chile&apos;s Atacama Desert, brings unique design problems in the form of possible large differential settlements of the foundation soils due to the dissolution of salts in northern Chile the soils often contain very high concentrations of soluble salts (nitrates, potassium, magnesium, and common sodium). When a leak in the liner occurs, the escaping solution dissolves these salts and triggers differential settlement. If the settlement is great enough, the geo-membrane tears, the leakage increases, triggering more differential settlement. The nitrate plants have experienced many occurrences of this phenomenon where a brine pond will undergo a sudden and complete loss of the impounded liquors. The authors present a simplified technique to quantify the differential settlement resulting from dissolution and provide a method which can be used to select a geo-membrane with suitable flexibility under axi-symmetric (multi-axial) load conditions to tolerate the predicted settlement. (This paper was previously published for Randol Gold Forum 1996 [Ref. 6]).

Jan 1, 1997

By R. Cooper, K. De Wet, A. Janwong

"Horsehead Metal Products is a zinc refinery in Mooresboro NC treating crude Waelz Oxide (WOX) to produce Special High Grade Zinc by a hydrometallurgical process, comprising leaching, zinc solvent extraction/electrowinning (SX/EW), melting and casting and bleed treatment. Cadmium removal by zinc dust cementation plays an essential role in the bleed treatment circuit to prevent a build-up of cadmium in the circuit. Silica, although not present at significant levels in the WOX feed material (approximately 0.3%), had a significant impact on the efficiency of cadmium cementation with zinc dust, most likely due to the passivation of zinc dust particles with silica gel. Solid/liquid separation efficiency by filter press was also impacted. The silica levels were mapped throughout the circuit in an attempt to identify the source of the silica issues. Adjustments including using PLS as feed to cementation, pH control in WOX leaching and neutralization have been introduced to mitigate the issues created by silica gel in the circuit. INTRODUCTION Located in North Carolina, Horsehead Metal Products Inc. is a hydrometallurgical zinc refinery processing Waelz Oxide (WOX) to produce Special High Grade (SHG) zinc. The flowsheet, known as the Modified Zincex® process, consists of leaching, solvent extraction, electrowinning, melting and casting and bleed treatment as illustrated in Figure 1. Cadmium cementation, part of the bleed treatment process, provides an essential bleed of cadmium from the circuit, as metallic cement. The Cadmium cementation circuit consists of agitated cementation reactors, a zinc dust addition system, filter presses, agitated purification (releach) reactors and a cadmium concentrate filter press Silica can be found in several forms in acid leaching. The first form is fine silicate particles. The size of the particles can vary from one to twenty microns (1). Fine silicate particles can lead to the formation of crud in solvent extraction circuits (2, 3). At Mooresboro, crud has been observed in Depletion, which is part of the solvent extraction circuit. Silica content in the solution in this section is high. The second form of silica is monosilicic acid Si(OH)4, which begins to polymerize almost immediately upon being leached into solution. Monosilicic acid polymerizes to silica gel or a silica precipitate dependent primarily on supersaturation (5). Factors that influence the rate of polymerization include temperature, sulfuric acid concentration / pH, hydrofluoric acid concentration, seeding, and dissolved salts concentration such as zinc and aluminum in the solution (4, 5, 6). In sulfate systems, silica solubility is reported in the range of 150 to 450 ppm of SiO2 (3, 5, 7)."

Jan 1, 2016

By J. D. Grenia

The Buick Mine is a joint venture of American Metals Climax, Inc., and Homestake Mining Company located 120 miles by road southwest of St. Louis, near the village of Boss, in the &apos;New Missouri Lead Belt&apos; (See Figure 1). Since start-up in 1969, over four million tons of lead-zinc ore have been mined and milled at Buick. Situated about 1,100 feet below the surface at an elevation 270 feet above sea level, the flat lying sinuous ore bodies are up to 250 feet wide, 85 feet high and several thousand feet long. Mineralization is galena, sphalerite and chalcopyrite in dolomite, Access to the mine is through two 18&apos;Ø concrete lined vertical shafts - one for servicing and the other for hoisting ore (See Figure 2). The mine is being worked by a modified room and pillar method using both rubber tired equipment and a sub-level rail haulage. Ore is broken from first pass headings, back and bench faces and transported by load-haul-dump units to ore passes located on 900 foot centers. The ore is pulled from chutes on the sublevel 90 feet below into 15 ton bottom dump cars and delivered in 10 car lots by a 15 ton diesel locomotive to a 42" gyratory crusher (See Figure 3). A recent innovation has been the introduction of two 50 ton trucks with plans to haul up to 60% of the ore on the mining level to an ore pass feeding directly to the primary crusher (See Figure 4). Ventilation raises up to 16&apos;Ø, which were originally planned for 900 foot centers, are now driven on 450 foot centers.

Jan 1, 1973

By S. D. Abbott

Mines are filled with a mixture of gases, some of which are toxic, flammable, or explosive. Others serve as early reporters of impending problems. Mines monitor these gases in order to ensure the safe, efficient operation of the facility and avoid losses or disasters. Two different approaches to monitor these gases have historically been taken. One kind of device measures the amount of each gas present by using selective detectors (e.g. handhelds and spectrometers). Another kind separates the mixture of gases into the individual constituents, then measures the amount of each gas present (e.g. gas chromatographs). Handheld units are the most widely used, but gas chromatographs are the most powerful yet underutilized units available to enhance mining operations. There are many misconceptions about the nature, applicability and proper use of each type of device, and little data is available. Up to this point, many people had only the manufacturers? claims to guide them. This study was undertaken to clarify the range of applicability, important characteristics, and value in use of these units in real-world situations. An additional goal of the study was to provide ways to evaluate comparative data, and thus aid mining operations in choosing the most beneficial and reasonable ways to use such devices in various situations and contexts.

Feb 23, 2014

By J. Casado

This paper presents the results of an analysis and summary of relevant literature on the mechanism of cementation of metals in acidic aqueous media, with the aim of reconsidering the conventional assumptions. The simplicity of the process as a mere galvanic metal displacement is discussed, and the real effects of pH and hydrogen pressure in different cases assessed. Finally, an alternative mechanism scheme with respect to the role of hydrogen species, in agreement with reported data, is proposed.

By Venkata Aneesh

This paper examines the desired blast fragmentation results associated with mining fleet performance at Sidney Quarry of Pike Industries, A CRH Company by reducing cycle times and hauling less oversize material generated from the blast to the crusher to increase the overall plant throughput. We are constrained with blast patterns due to the poorly sorted and fractured seams in the quarry, which is angled at 35° NE and dipping at 80° and runs parallel to the Interstate-95 highway on the east of the quarry boundary about 600 ft, making it challenging to alter the blast patterns for optimal yield. We evaluated multiple relationships between blast patterns in conjunction with loader diggability. Results analyzed include the digging hours, fleet cycle times, and the fragment size with the optimized blast design through 3GSM software to arrive at the optimal yield to maximize the crusher throughput. Our primary objective is to focus on safety with efficient cycle times and clean floors & clean face generation for better operational efficiencies. Secondly, to optimize the crusher yield which is an integral part of quarry operation. Further, this paper provides the utilization of 3GSM blasting techniques in quarry applications with computer vision fragmentation analysis and VizaLogix, a fleet management software to analyze the cycle times sampling.

Feb 1, 2024

By J. Sohn

The most promising near-term alternative to fuel cell driven vehicles is probably Hybrid Electric Vehicle (HEV or EV) technology. HEV technology combines the best characteristics of fuel-driven engines, electric motor drives, and energy storage components. It is designed with a combustion engine that functions as the primary power source, and an electric power storage system that functions as the secondary power source. The presence of the secondary power source allows designers to size the combustion engine for cruising power requirements. A new energy source for HEV or EV market will become lithium ion batteries (LIBs) in the near future. LIBs for HEV or EV has large scale about more 10,000 times than small size one for IT devices in order to achieve high electric density/capacity and high efficiency, etc. In those reasons, physical treatment of the batteries is more difficult for stable dismantling in comparison with the smaller one. Hybrid vehicle sales will grow by nearly 400 percent during the next seven years, according to a new report from analyst firm ABI Research. By 2013 hybrids will make up 6 percent of annual U.S. auto sales. The traction battery pack will become air-cooled LIBs which consists of several modules of Li ion battery and connected in series/parallel configuration to provide about >450 VDC, >150 kW peak power, and >80 Ah capacity. As the use of these batteries tends to increase significantly for the next years, it is relevant issues that development of new recycling methods as well as optimization of existing processes to treat spent LIBs for HEV have being addressed in order to obtain sustainability. In this study, physical treatment containing stable electrical discharge of spent LIBs for HEV was carried out for recovery of valuable metals from the batteries. Also In order to increase the yield of valuable metals through physical treatments such as electric discharge of spent batteries, crushing, and classification, we also focused on the recovery of cobalt from +8 mesh fraction due to its large portion in crushed intermediates.

Jan 1, 2010

By M. Ahmadiantehrani

The concept of hypochlorite treatment prior to cyanidation in the heap leaching of low grade carbonaceous gold ores is discussed. Laboratory column leach tests using a low grade carbonaceous ore were performed to investigate the effects of pH, concentration, hypochlorite consumption, and bed height on the total gold extraction. At high pH, the hypochlorite stability increases and thus, hypochlorite consumption is decreased. At room temperature, the total gold extraction is proportional to the hypochlorite consumption. However, at some point additional hypochlorite consumption does not increase gold extraction. Gold recoveries of 10 and 80 percent are obtained for 12 and 167 lbs/ton hypochlorite consumption, respectively. Increasing hypochlorite concentration increases the rate of extraction. For a given hypochlorite consumption gold extraction was increased by shortening the ore column height. Finally, calcium hypochlorite is more effective than sodium hypochlorite.

Jan 1, 1990

By Alafara A. Baba, Yakubu A. Dallatu, Kehinde I. Omoniyi, Shemang Y. Chindo, Edith B. Agbaji

With the rise in global demand for pure copper, there is an urgent need to consider the processing of low-grade chalcopyrite ores. Ammoniacal leaching solutions have been reported as effective and efficient leachants for the dissolution of chalcopyrite. This work reports on different parameters that influence the leaching kinetics of a Nigerian chalcopyrite-rich siderite ore obtained from the Wase local government area of Plateau state, Nigeria, and assayed as 11.30 weight percent copper.

May 1, 2023

By John S. Livermore

I feel very privileged to be added to the distinguished group that has received this award since the first recipient, Reno Sales, received it in 1954. If my research is correct, the last geologist to be honored was Bill Callahan in 1982. Perhaps the Awards Committee decided it was about time to select a geologist, and I became the beneficiary. Regarding the discovery of the Carlin ore body, it was the culmination of several studies - one going back as far as 1939 when a US Bureau of Mines engineer named W.O. Vanderberg recognized an unusual type of gold mineralization in sediments in northern Nevada. What was unusual was the fact that the gold was so fine that it would not concentrate in a pan. This, plus the study of the Roberts Mountain thrust by Ralph Roberts (1960) and conversations with Harry Bishop, manager of the Gold Acres Mine, pointed Alan Coope and me in the direction of the Lynn Window and, eventually, the Carlin discovery. There has been a great deal written about this discovery. I thought it would be interesting to discuss the evolution of Carlin gold exploration in Nevada since this time and to discuss the changes in perception of this unique type of mineralization. The method used by Coope and me in following up on Roberts&apos; work was to map geologically the Roberts Mountain thrust and conduct geochemical sampling of favorable outcrops and float. Coope was highly experienced in geochemical exploration, as he had graduated from the Royal School of Mines in London, studying under John S. Webb, one of the pioneers of geochemistry as applied to mineral exploration. We first considered using pathfinder elements, but finally concentrated on gold analyses alone, even though the sensitivity of fire assays used at that time was only about one-half part per million. According to the spatial relationship of the mineralization to the Roberts Mountain thrust, as pointed out by Roberts (1960), we were looking for mineralization within the thrust itself. Our models were the known Gold Acres and Getchell mines, which contained reserves on the order of 0.9 to 1.8 mt (1 to 2 million st). These were not of substantial size, but I had hoped we might find more than one of these tributary to a mill that would justify an operation for our employer, Newmont Mining Corp. What we ended up with was the type of deposit we were looking for - an open pit deposit of micron gold, which the old timers had missed because the gold was not capable of being panned. But never in our wildest dreams did we think there was a chance of finding a body containing 10 mt (11 million st) of ore at 0.30 oz/st (10.3 g/t).The deposit was not in the thrust proper but was found in a favorable horizon of Roberts Mountain siltstone that was below the thrust. This is the first example of how a model should not be followed blindly. Newmont was successful in keeping this discovery quiet for some time. After a considerable amount of drilling, a rumor circulated that they had discovered a large low-grade ore body of around 1.7 to 2.1 g/t (0.05 to 0.06 oz/st), which of course would not have been economic with gold at $1.13/g ($35/oz), which was the fixed price at that time. The company, for obvious reasons, did not discourage the rumor. When, however, the true results came out there was a lot of feverish activity. Because of this new type of so-called "invisible gold," which could have been missed by the old timers, the thought was that other deposits would be discovered very soon. The Carlin and other smaller deposits, including Bootstrap, Blue Star and Gold Quarry, were in windows where the lower plate of the Roberts Mountain formation (below the thrust) had been exposed by erosion. This then became the new

Jan 1, 1997