Search Documents

By Jung-Hum Lee, Young-Joon Lee, Eui-Joon Hong, Seon-Hong Kim, Chan-Dong Kim, Keon-Woong Jeong, Ki-Lim Kim

"Subsea tunnel needs to be built over 50km long to connect between nations and continents. However there are only 19 tunnels longer than 5km in Korea, and there is no history of constructing and operating a tunnel longer than 50km. As the concept of a subsea tunnel, which withstands high water pressure and has an extremely long length is completely different from that of a land tunnel, all kinds of the latest technologies for tunnel construction are required such as survey and analysis of geology, design and construction under high water pressure, ventilation and prevention of disasters within an ultra long tunnel. Therefore, this paper describes the determination of tunnel cross-section under a high speed railway, structural stability, ventilation and fire safety under construction and operation, etc. through the virtual project for the length of 108km subsea tunnel under high water pressure of maximum 20bars from Honam to Jeju island in Korea. 1. INTRODUCTION The Honam-Jeju virtual project is subsea tunnel project to link from Honam(land) to Jeju(island) extending the currently operating Honam high speed railway line, and the same express train(t=18, design speed 350km/h, total train length 200m) operating at Honam line is applied in this project. As Honam-Jeju site is approximately 80km in straight distance with 160m maximum depth, subsea tunnel project should determine the various issues such as air quality/ventilation, aerodynamics, temperature, drainage, fire & life safety, structural stability. Figure 1. is the plan of subsea tunnel, with be constructed using Shield TBM. This double tube-Single track is composed of cross passages (every 350m in general section and 40m in emergency station), service tunnel, pressure relief ducts (every 250m), cross-over tunnels, shafts and emergency stations. 2. ALIGNMENT AND SITE CONDITON This project is planned as an ultra long tunnel of total length more than 105km via existing islands between Honam and Jeju island because straight alignment requires an artificial island which has high cost and construction risk, by deep water depth, though this is the shortest distance (see Fig 2). Water depth and topography in project site is divided into two blocks by Chuja Island. In first block to Chuja Island, depth of the water is 40m on average and maximum 60m, which indicates gradual change of water depth relatively. Also, outcrop bedrock is widely distributed near island."

Jan 1, 2016

By Paul H. Johnson

The CH Leaching process is a new, more sophisticated, form of gold, silver, uranium and sulfide copper heap leaching wherein each layer of a multi-layered heap is divided into a number of independent cells, each of which are successively formed and leached in the top layer of the heap to their maximum economic recoveries, and then rinsed and sealed from further leaching. Triangular earth berms form the outside walls of the heap and a gridwork of rock-filled berms on top of the bottom pad form independent under- heap solution storage zones. The high degree of solution recirculation and staging that occurs in this process produces a relatively small volume of very rich pregnant solution. The cellular heap design and its mode of operation result in a uniform, intensive, long-term leach for all of the ore particles in the heap. Besides improved metal recoveries, the process appears to have several cost and operating advantages. In the CR2MR process, sulfuric acid and a soluble sulfide are added to a gold and/or silver pregnant leach liquor to precipitate most of the contained silver, mercury, copper, etc. as sulfides at a pH below 2.5. The other product of the reaction is solubilized HCN. Following a liquid-solid separation step, cyanide is regenerated in the supernatant solution by raising the pH to a level above 9.0. This process regenerates a portion of the cyanide used in the leaching step, removes contaminant ion species (silver, copper, mercury, etc.) from the leach solution and, in a subsequent step, recovers the gold in an enriched form. It is believed that substantial cost savings may be experienced by the use of this process in some gold and/or silver leach systems.

Jan 1, 1984

By A. E. Sears

The intent of geomorphic landform design is to mimic the function of the natural landscape. In a surface mine reclamation application, geomorphic landform design has the potential to mitigate stream loss. This research quantified features of reference landforms and performed computer modeling of a conceptual valley-fill design using geomorphic landform principles. A design was created using published design parameters with a software design tool (Carlson Natural Regrade with GeoFluv). Three additional designs, incorporating field-obtained regional geomorphic landform parameters, were completed and resulted in a geomorphic landform design specific to southern West Virginia. This work illustrates the importance of field determination of the ridge to head-of-channel input and drainage density parameters. Values of ridge to head-of-channel distance measured in this study were consistently an order of magnitude greater than software recommended values (SRV); SRV = 24 m (80 ft) versus field= 220 m (720 ft). Similarly, for the drainage density parameter, the software recommended range is 6 to 9 km-1 (80-120 ft/ac). The field measurements for central Appalachia quantified the drainage density to range from 5 to 5.3 km-1 (67-70 ft/ac). This affects Appalachian valley-fill stream construction by making the stream lengths shorter and the land slopes steeper with straighter headwater channels compared with areas in the southwestern United States. While the application of geomorphic landform design to surface mine sites presents challenges, this work provides support for future applications.

By O. J. R. Baena, N. J. Zapata

In Colombia, more than 15 regions and around 100 municipalities develop gold mining at different scales, and these operations generate mining waste composed of processing fluids and crushed rock with metals and high silica content. Cement production requires clinker, gypsum and other corrective additives. Clinker results from the partial fusion of some minerals including silica. In this study is proposed to evaluate the effect of the use of mining tailings sands from gold mining in the manufacture of clinker. The proposed methodology will allow the characterization of the sands to manufacture a cement specimen and measure its physical and fire properties

Mar 2, 2022

By Gary B. Glass

In 1997, 92.3% or 235.7 Mt (259.8 million st) of coal produced in Wyoming came from the Wyodak coal zone in the eastern Powder River coalfield. The mined portions of the zone consist of one to three beds of coal with an aggregate thickness between 15 and 33.5 m (50 and 110 ft). The thickest expression is 61 m (200 ft). The delivered coal from this zone averages 0.33% sulfur, 5.12% ash and 19.98 MJ/kg (8,590 Btu/lb.). This coal zone occurs at or near the top of the Paleocene Fort Union Formation, which is overlain by the Eocene Wasatch Formation. There is also production from two coalbeds in the lower portion of the Wasatch at the southern end of the basin. Production of coalbed methane derived from the Wyodak coal zone is currently an estimated 289 Mm3/a (10.2 billion cu ft/year). This production is occurring west and downdip from the coal mines and is increasing each year.

Jan 1, 1998

By Sufi Md Gulzar, L B. Roy

Rock engineering tasks like tunnelling, dam and building construction, and rock slope stability rely heavily on properly estimating the rock’s uniaxial compressive strength (UCS), a crucial rock geomechanical characteristic. As high-quality specimen are not always possible, scientists often estimate UCS indirectly. The primary objective of this paper is to assess the efficacy of long short-term memory (LSTM), K-nearest neighbour (KNN), a combination of particle swarm optimisation (PSO) with an artificial neural network (ANN), and adaptive neuro-fuzzy inference system (ANFIS) to estimate the UCS of sandstones from Jharia, Dhanbad, India. Point load index (PLI), porosity (n), P-wave velocity (Vp), density (ρ), and moisture content (%) are the parameters used for the present study. Finally, a comparison was made between the various prediction algorithms outputs. The findings of the study validated the effectiveness of computational intelligence methods in forecasting UCS compared to other models used in this paper. The KNN achieves overall the best results, with an R2 of 0.95 for training, 0.94 for testing, and an RMSE of 0.03 for training and 0.05 for testing.

Nov 23, 2023

By Alafara A. Baba, Yakubu A. Dallatu, Kehinde I. Omoniyi, Shemang Y. Chindo, Edith B. Agbaji

As a result of the rise in global demand for pure copper, there is urgent need to consider the processing of low-grade chalcopyrite ores. Ammoniacal leaching solutions have been reported as an effective and efficient leachant for the dissolution of chalcopyrite. This work reports different parameters that influence the leaching kinetics of a Nigerian chalcopyrite-rich siderite ore obtained from Wase Local Government Area, Plateau State, Nigeria, and assayed as 11.30 wt% of Cu. At the optimum leaching conditions (0.4 mol/L NH3-( NH4)2SO4 leachant concentration; 75 °C reaction temperature; 45 μm particle size), the extent of chalcopyrite ore dissolution reached 87.4% within 120 min. The dissolution rate was affirmed to conform to the diffusion control mechanism with the activation energy, Ea, of 38.84 kJ/mol and a reaction order of 0.661 for the leachant concentration being established. The leaching mechanism was affirmed by characterizing the raw ore and the leached product by XRD and SEM-EDS analysis. Ascertaining optimal leaching conditions for copper using alkaline leachant is advantageous from the environment and economic points of view.

Jan 6, 2023

By John M. Hill

Automation technology has many facets, some well tested and proven, some yet to be put to the acid test of economic reality. In this paper, we will limit our purview to the former. Consider, if you will, an automated handling system combining high-speed conveyors and automatic devices on-line which not only provide signals for routing and sorting, but also format those signals for the production of manufacturing, inventory, shipping and billing paperwork. This is not futuristic, but practical and a realistic accomplishment. Therefore, the following discussions will address today's challenges not with tomorrow's solutions, but rather, with an established technology which is playing an increasingly prominent role in materials handling systems. Until recently, relatively modest importance has been attached to the timeliness of information feedback from the production or assembly line, warehouse or distribution center. Thus, initial applications of automatic identification equipment focused almost exclusively upon the control of materials flow - that is, routing, sorting, etc. However, these systems have performed successfully and quietly established an enviable track record as reliable materials control tools.

Jan 1, 1973

By N. Damiano, J. Noll, C. Zhou, J. DuCarme

"Preventing machine-related injuries is one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable were characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which cause little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects. INTRODUCTION An average of 250 injuries occur every year during operation of Continuous mining machines (CMMs), and 43 miners have been killed by striking or pinning accidents involving CMMs in the U.S. from 1984 to 2015 (Mine Safety and Health Administration, 2015). In addition, there have been 10 fatal accidents involving mobile haulage equipped with trailing cables from 2000 to 2015 (Noll et al., 2017). In response to these fatalities and injuries the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 requiring the use of a proximity detection system (PDS) on all CMMs except full-face machines and proposed a regulation in 2016 which would require a PDS on other mobile underground equipment. Current PDSs approved for underground use are magnetic-field based. The PDS contains machine-mounted magnetic field generators that create fields around the machine. The other part of the PDS is a miner-wearable component (MWC) that reads the flux density of the generators. These systems use the magnetic field strength readings from the MWC to determine whether a miner is at a safe distance from the machine. A stable magnetic field is essential for the accuracy of the system."

Jan 1, 2018

By J-P Franzidis, M. C. Harris

Increasing costs, falling grades and a low gold price have caused severe problems for many of South Africa's gold mines. The need to maximise efficiency is extremely urgent. This paper describes the use of column flotation cell s to scavenge significant quantities of additional gold from flotation plant residues; in particular, very fine particles of free gold not recovered by conventional flotation. Experimental gold- specific collectors enhanced gold recovery significantly. The paper also reports the results of other plant trials, carried out on a variety of ores.

Jan 1, 1991

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015

By H. Habenicht, E. Urschitz

Three mining methods for full extraction in flat coal seams - i.e., longwall (L W), shortwall (SW), and rib pillar extraction (RPE) - are com- pared with each other in view of the introduction of a mechanized, self-advancing roof support. Features are shown according to which RPE appears most attractive under certain conditions. In this presentation, the mining methods are outlined and discussed. The new support (Alpine Breaker Line Support, ABLS) is described, and its employment is explained. A trial operation in RPE using the ABLS has been conducted successfully in a South African coal mine. The results and improvements are stated.

Jan 1, 1988

By J. Stawovy, A. Fourie, J. D. Quaranta

Coal refuse impoundments are disposal facilities specifically designed for the coal mining industry. Re-purposing refuse impoundments for co-disposal with natural gas flowback water and waste rock overburden has been investigated. The aims of this study were to investigate properties of coal refuse classification under the influence of co-disposed wastes as geochemical material exposure pathways from hydraulically exposed sodium and calcium ( Na+, Ca2+) cation loading from disposal of flowback water produced during the development of horizontal drilled natural shale gas frack wells, and waste rock having limestone characteristics. The geotechnical index classification of saturated cohesionless refuse is required to evaluate the liquefaction potential for strain or strength loss contributing to ground movements. This study is relevant to identifying changes in the coal refuse geotechnical index classification as sand-like, clay-like, or a borderline transitional material from the effects of ion and waste exposure in the impoundment’s reservoir porewater. Laboratory geotechnical tests were performed on fine coal refuse blended with different cations to classify the altered plastic behavior and index classification. Following determination of the index classification, the specimen’s stress–strain responses were investigated through isotropically consolidated undrained (ICU) triaxial compression tests. This experimental study culminated with two salient findings: the first is that introduction of ions alone into the refuse tailings or impoundment porewater resulted in significant material changes in property index classification, and the second finding was that the difference in refuse index classification did not correlate into noticeable effects of the monotonic undrained triaxial strength parameters.

Jul 5, 2022

By I. Iwasaki, K. A. Smith, X. Cheng

A cathodic decomposition model was examined for both pyrrhotite and chalcopyrite in an attempt to analyze the formation of surface coatings in deoxygenated solutions at natural, near neutral pH. Combination potentials established between the mineral-grinding media pair were simulated by applying a potential of -0.455 V (vs. a standard hydrogen electrode) either to a pyrrhotite or to a chalcopyrite electrode. Chronoamperometry was used to study the polarization behaviors and alteration of mineral surfaces through cathodic processes. The kinetic parameters of cathodic decomposition of pyrrhotite and chalcopyrite were determined and compared. It was concluded that pyrrhotite decomposed faster than chalcopyrite in near-neutral pH solutions. Both minerals were then covered by a film consist¬ing mainly of iron hydroxides, which adversely affected their flotation.

Jan 1, 1999

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

Belle Fourche Shale was processed and characterized for use as a clay-based ceramic. The shale was wet sieved to produce particles that were ± 150 μm. X-ray diffraction (XRD) revealed that the -150 μm material was enriched in clay content compared to the unprocessed materials, whereas the oversize material was enriched in quartz compared to the undersize sample. Particle size analysis was performed on the—150 μm sample, which showed that the median particle size was around 10 μm. Scanning electron microscopic (SEM) analysis further confirmed the small plate size, which appeared to be primarily layered clay particles. Next, the -150 μm particles were rolled into a green body, dried at room temperature, and fired at 998°C. The fired piece was analyzed by XRD and contained 6 wt% hematite, 55% quartz, 19% microcline, and various other minor amounts of minerals. When fired at 1152 ℃, mullite was found with increasing hematite compared to the 998 ℃ firing. A multi-spectral analyzer was used to quantify the color change of the 998 ℃ fired (orange) to the 1152 ℃ fired (red) samples. Micro-computed tomography (Micro-CT) of the unfired body exhibited very few large pores, while the piece fired at 998°C also exhibited few and small pores, the overall porosity of the fired body increased. Microhardness data, obtained from the aforementioned samples, resulted in Vickers Hardness (HV1.0) values of 70.8 HV1.0 (998 ℃) and 485.7 HV1.0 (1152 ℃). Three-point bend testing was performed, giving an average strength of 23 MPa on pieces fired at 998 ℃. The average bending strength of the samples fired at 1152 ℃, was 55 MPa.

Sep 26, 2023

By E. Ashworth

A thermistor probe has been developed to measure in situ temperature profiles underground. A full description of the probe is given. Data collected from the probe has been used to compare the actual profiles with those predicted from a finite element analysis using laboratory measured thermal properties of the different rock types. This comparison indicates the applicability of laboratory measured parameters in modeling the real conditions. Factors such as applied pressure, moisture content and anisotropy on laboratory measurements is discussed.

Jan 1, 1983

By K. Pietruszka

The article presents the concept of the application of the Finite Element Method (FEM) and ABAQUS software in the global monitoring of changes in the rock mass and on the surface of the area, as a result of backfilling the workings. Waste materials applied for stabilizing old mining workings can have a strong influence on the rock mass and surface. According to the regulations, this process should be carefully monitored, especially in terms of the safety of surface structures and rock mass stability. The article presents the concept of an analytic and graphic presentation of the results of the measurements of old workings, applying the Finite Element Method and ABAQUS software in model studies. The main purpose of such interpretation of the geodetic observations results is the application of methods providing wide possibilities to present the geometry of workings, their changes and the influence of the rock mass and surface.

Jan 1, 2008

By Valerie Kollonitsch

Functional mineral pigments are used in large quantities in paint, paper, plastics, rubber, textiles, agriculture, and several other industries. U.S. consumption in 1969 is estimated at over 5 million tons a year, valued at nearly $150 million, as shown in Table 1. Originally extender pigments were employed only to lower cost. They were thought of merely as adulterants to replace more expensive prime pigments and binders. However, over the years their role has become better understood, and today their main functions are: - Increasing strength, stability, and service life. - Improving surface properties. - Enhancing application and processing properties. - Extending prime pigments. - Controlling viscosity and package stability - Lowering overall costs of the finished product. The principal minerals used as functional pigments are kaolin, ground calcium carbonate, talc, and asbestos. Other minerals include barytes, attapulgite, diatomite, mica, ground silica, wollastonite, and nepheline syenite. Several synthetic products, including precipitated calcium carbonate; precipitated, gel, and fumed silica; alumina trihydrate; and barium sulfate, compete with mineral products. They are more expensive, but often have more closely controlled particle size or other properties because they can be tailor-made according to the requirements. This paper covers only natural products selling for $10 or more a ton, approximately the lower limit for pigment grades. Data refer only to consumption in pigment applications. For example, such applications as filter aids for diatomite are not included. Key properties of the major mineral pigments are given in Table 2. It is important to note that these properties are primarily physical rather than chemical. In general, these products are sold to performance specifications for what they can do rather than on chemical composition specifications on what they contain.

Jan 1, 1969

By John A. Riddle

Some of the pitfalls and problems in selecting and applying corrosion-resistant materials in uranium plants are discussed, together with some suggested solutions. Includes some cost data.

Jan 1, 1979

By Kenneth K. Landes

So far my consulting in industrial minerals has been confined principally to carbonate rocks,-salt, coking coal, and glass sand. Much of this work has been for companies either too small for a full-time geological staff or unaware of the value of employing one or more qualified geologists permanently. It gave me considerable personal satisfaction to see several of the latter companies employ one or two full-time geologists after the completion of a consulting contract with them. One possible reason why some companies lack the wisdom to hire geologists is that they are dominated by engineers who still subscribe to the old idea that engineers are self-sufficient in all fields. They could have learned this from their professors. I once knew a Dean of Engineering who got purple in the face when a faculty committee was discussing the financing of a broad gauged engineering project and suggestions were made that assistance be obtained from the Schools of Business and Law and from some of the science departments tie pounded the table and shouted "Engineers are trained to handle all this!" In teaching engineering geology some years ago I used to tell the class repeatedly that the course would not make them geologists, that the purpose was to teach them

Jan 1, 1972