Search Documents

By E. Finch

Beneficiation tests were conducted on samples from three ore zones in the Los Monos, Navay orebody in Táchira State, Venezuela as part of an overall feasibility study. The scope of work included ore sample characterization, flowsheet development, and optimization of beneficiation variables on a bench scale followed by confirmation on a pilot plant scale. Phosphate in the ore samples occurred primarily as francolite and was associated with quartz, kaolinite, and feldspar. Liberation of the phosphate began at 589 microns (28 mesh) for the main ore zone sample and at 295 microns (48 mesh) for the lower-grade ore zone samples. Development tests on simulated mining composites demonstrated that the samples responded well to 589 micron (28 mesh) grinding, two stages of high intensity scrubbing, conditioning at high % solids with caustic and equal amounts of tall oil and fuel oil, and separate coarse and fine flotation circuits with one stage of roughing and two stages of cleaning (reflotation). Concentrates in the range of 31.5-34% P205 with recoveries from 64-70% were obtained from the mining composites. Product quality for all concentrates in the range of 31.5 % P205 was good; 1.40 CaO/P205 and 0.04-0.05 minor element ratios. Confirmation testing in a continuous pilot plant produced results similar to those achieved in the laboratory.

Jan 1, 1993

By Peter G. Dunn

Geologic studies during development at Copper Flat were directed at acquiring the information necessary in evaluating a low-grade porphyry copper deposit. In addition to the geologic mapping and core-logging of a typical exploration project, these studies included the following : (1) careful checks on the sampling and assaying (2) selection of representative samples used to establish the recoverable amounts of precious metals in the ore (3) examination of underground workings driven to provide samples both for metallurgical testing and for assay comparisons (4) evaluation of plant site and waste dump areas as non-mineral, including a placer examination of the taillngs disposal area (5) location of an adequate water supply. All these investigations were carefully documented to provide the necessary data both for the engineering design and, more importantly, for the feasibility studies required for successfully financing the project.

Jan 1, 1981

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type and causes of accidents in the Turkish coal-extracting industry using the analytic hierarchy process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type and causes of accidents. For this purpose, first-, second- and third-level hazards consisting of location, type and causes of accident were determined by using the data of fatal mine accidents in underground and openpit coal mining in Turkey between 2010 and 2020.

May 1, 2024

By D. A. Fenton

Two large 34 ½ foot diameter mills have seen seven years of continuous operation before massive fracturing occurred on one of the trunnion cones. These fractures were discovered when liner changes were made. Four modes of failure were identified, three of the modes combining to cause a large circumferential tear in the 4-inch cone plate. A theoretical account is made of the modes of fracture and comparison made with field results. New material was used to repair the fractured cone, and the complete repair took ten weeks. The repair was monitored and lasted twenty-six weeks before the newly designed structure was available.

Jan 1, 1982

By T. E. Masoner

The struggle to get the minerals industry seriously interested in high intensity wet magnetic separation* has been difficult. The high capital cost of the equipment, the lack of basic research, the lack of operating information, and the diverse characteristics associated with different minerals and ores have prevented the development and use of HIMS-W on a wide scale. The Climax Molybdenum Company, a Division of American Metal Climax, Inc., located at Climax, Colorado, was among the first companies in the Americas in recent years to support the development of HIMS-W to recover weakly magnetic minerals on a large scale. The Climax Molybdenum Company, one of the world's largest underground mines, processes about 40,000 tons per day of ore, from which about fifty million pounds of molybdenum disulfide are produced each year. By-products include tungsten, iron pyrite, tin, and some monazite.

Jan 1, 1968

By P. McGrath

From the mid-1980s through 1997, Echo Bay Alaska evaluated reopening the historic Alaska-Juneau (AJ) gold mine. Their original proposed project underwent numerous modifications in order to minimize the potential for significant environmental impacts. One of the major modifications involved changing .the tailings disposal method from a conventional tailings impoundment to submarine tailings disposal (STD). In 1995, the U.S. EPA began work on a Supplemental Environmental Impact Statement (SEIS) to assess the impacts of the STD proposal. Key features of the STD impact assessment included fate and transport modeling to determine the extent of tailings deposition and the use of ecological risk assessment to predict marine impacts during deposition and ecosystem recovery following STD. A key feature of the SEIS regulatory process included a rulemaking proposed by EPA to exempt the AJ tailings from effluent regulations. Critical to success in moving the project forward was early development of an interactive working relationship with other regulatory agencies and the public.

Jan 1, 1998

By K. Biswas

In general, it cannot be assumed that the strength of coal pillars remains constant over long time periods. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing load-bearing capacity of the pillars. This paper discusses a unique approach to determine the time dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15 and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar and the strength profiles were determined for each hole using the Borehole Penetrometer. The strength data were treated statistically to establish time dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 1999

By S. R. Dindarloo

"Truck-shovel systems are the dominant material loading and haulage machinery in open pit mining operations. Optimal selection, sizing, and allocation of this capital intensive equipment is highly desirable for both achieving production targets and improving the mine’s economics. In this study, discrete event simulation technique was applied for modeling material transportation in Golegohar open pit iron ore mine in Iran. Direct observation of the material loading and haulage for duration of three months resulted in statistical modeling of the operation in the form of probability distribution functions. These probability models were used as the inputs of a stochastic simulation model constructed in GPSS/H simulation language. The model was validated through comparison with the actual operation and was used to test different what-if scenarios and sensitivity analysis of the current system. Some modifications in the number of trucks, shovels, and dispatching strategies were proposed. Simulation resulted in considerable improvements in the mine’s production and economics.INTRODUCTION There are three different mechanisms of discrete, continues, and hybrid material transportation in open mines, including but not limited to: i) in-pit crusher and conveyor belts (hybrid), ii) slurry piping (continues) and iii) truck-shovel system (discrete). Although, each mechanism has its advantages, the truck-shovel system is the dominant method of material loading and handling in open pit mines owing to its high production rate, excellent flexibility, relatively low operating and capital costs, and good maintainability. General objectives of optimal equipment selection include: i) meeting the long and short term requirements of production rates, ii) human & equipment safety, iii) environmental protection, and iv) economic operations (Figure 1).The two most important decision factors on a truck-shovel system selection and sizing are the equipment geometry and size. Geometry (equipment width, weight, turning radius, swing angle, etc.) is mostly controlled by mine’s designs and layouts, as well, as operational constraints. After selection of a favorable geometry based on the constraints; the next step is to select the equipment manufacturer. Once the geometry and manufacturers are selected; the next step is to decide on models (e.g. Bucket size) and required number of each unit"

Jan 1, 2015

By Roy A. Grancher

HAPPY BIRTHDAY Not only is 1971 the Centennial Year of the AIME, but it also marks the One Hundredth Anniversary of the United States Portland Cement Industry. On September 26th in 1871 David O. Saylor of Allentown, Pennsylvania, received his patent Numbered 119,413 for the manufacture of portland cement. "Cement" had been used in the United States before that. This was, however, natural cement - a direct product of rocks as found in nature, usually burned at low temperatures in open kilns. During the early 1800s this natural cement played an important role in such projects as the building of the Erie Canal. It was only after the Civil War that small amounts of high priced portland cement was imported from Europe. The successful use of this material in construction led to Saylor's experiments and subsequent patent for the manufacture of a scientifically controlled product in this country. These one hundred years have witnessed four major "ages" of cement . . . three of them occurring in the last quarter century since World War Two. The first age was the "Age of Development", a seventy-year period which saw the growth of cement and its concrete end uses as major construction materials. Next followed a period called the "Age of Demand" when, after the war, cement became in short supply relative to large building requirements. In effect a cement shortage existed. The decade of the Sixties proved to be the "Age of Reaction", with its courses of action coming in response to the problems that arose when the industry's expansion programs provided too much capacity. Today cement, and the concrete industries, find themselves entering the "Age of Reason". Overcapacity, low price, rising costs, and poor returns are several of the reasons behind that name, As these industries face the construction challenge of the Seventies, and beyond, the application of basic management principles (otherwise known

Jan 1, 1971

By R. E. Hucko

The principal thrust of the U.S. Department of Energy (DOE) Coal Preparation R&D Program is to develop technology to reduce the ash and sulfur contents of United States coals to levels such that the resultant product can be formulated into a high quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. Specifically, the objective is to develop and refine cost-effective physical and chemical beneficiation processes to extract 85-95 percent of the total sulfur and ash. The Coal Preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in-house and by a cross section of industrial organizations, universities, and national laboratories. Research is subdivided into three areas -coal characterization, beneficiation, and ancillary unit operations. This paper will provide a brief overview of many of the research projects being carried out in these areas in fiscal year 1984.

Jan 1, 1984

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

A multi-layer gangue roof of a steeply dipping coal seam with a large mining height face area was analyzed using physical simulation, numerical simulation, theoretical analysis, and field measurement methods to evaluate the roof deformation and the mechanisms associated with the instability of the hard gangue and soft coal interlayer. The results indicated that the first weighting step of the multi-gangue roof was larger than that of a non-gangue roof, but periodic weighting steps were similar. The overburden collapse height was lower in the multi-gangue roof than in the non-gangue roof due to the buffering and supporting function of the collapsed gangue. Moreover, the failure of the coal interlayer was the key factor in the collapse of the multi-layer gangue. A mechanical model was established for the hard gangue and soft coal interlayer based on a revised Prandtl squeezing theory. The limited load of the interlayer and maximum resistance of the shield support was thusmodeled. The maximum resistance of the support increased with the dip angle of the seam and burial depth. It also increased with the interlayer thickness at thicknesses below 2.75 m. It reached a peak when the interlayer thickness was between 2.75 and 3 m and exhibited a decreasing trend when the thickness was greater than 3 m. The results were confirmed using physical simulation and a field test. Certain measures were proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

Jun 30, 2020

By Yi Luo, FENGLIANG WU

Mine gob has long been a safety concern in the coal industry due to the air flowing through the gob area. Therefore, knowledge of the airflow distribution and locations of hazard zones in longwall gob is important to prevent and control these hazards. Due to the inaccessibility of mine gob, many numerical studies have been performed to simulate gob air leakage using computational fluid dynamics (CFD) programs, but most of the studies isolated the gob from the mine ventilation network (MVN) with only predefined pressure boundary conditions. The MVN is, in fact, not static in a dynamic longwall mining process, and it consequently changes the boundary conditions and the gob flow field (GFF). Therefore, the MVN should be incorporated in the CFD model to prescribe the transient boundaries. However, it is very challenging to couple the 1D MVN and the 2D/3D GFF to make the mine ventilation simulation realistic. This research uses a proposed novel finite tube method (FTM) to couple the MVN and GFF. In the FTM, the GFF is discretized into a finite number of flow tubes, each of which is formed by two adjacent streamlines. These tubes connect the MVN into a new coupling network. Based on the FTM, a model for gas migration in gob is established for delineating the hazard zones of explosive methane concentration and spontaneous combustion.

By A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to a reduction in travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation nay be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways nay contribute to formation. The study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Company to identify causes of the problem.

Jan 1, 1982

By R. B. Elver

The St Lawrence Seaway, a deep-water canal system between Montreal and Lake Ontario, was opened for navigation on April 25, 1959. Prior to the opening of the new Seaway, small boats known as canalers and a few deep-sea carriers, primarily from Norway since World War II, were the only ships able to journey past Montreal into Lake Ontario through the old Canadian St. Lawrence canal system. Thus it was necessary for many tons of bulk and general cargo to be shipped all-rail to and from Atlantic ports or to be transhipped to and from canalers. With the opening of the new Seaway, large Great Lakes bulk carriers and a much larger percentage of the world's shipping fleet are now able to sail directly from the sea to the heart of industrial North America. In this paper, the historical events leading up to the construction of the Seaway and the physical nature of the Great Lakes transportation system are briefly reviewed. Following this, an attempt is made to evaluate the effects of the new Seaway on Canada's mineral industry. Because the Seaway has been in operation for only one season, this paper must be considered only an interim report. Because of the importance of the Seaway to iron ore, this commodity will be dealt with in detail, although the effect on other mineral commodities such as coal, petroleum, nonferrous ores, iron and steel will be mentioned. At this time the author wishes to thank the various company and government officials who provided both factual information and critical opinions.

Jan 1, 1960

By Omar. M. Arafat, Edgar Pérez, Kyle. M. Bartholomew, Robert. E. McIvor

The “circulating load” confounds understanding of ball milling circuits. Conflicting opinions exist as to its role. Should it be high, or low? Why does it even exist? It is commonly accepted in the plant as a given, the outcome of largely unknown factors. As such, it may often go unmeasured or even ignored. This paper describes the importance of the circulating load in wet ball milling circuits. It is characterized not only in terms of solids mass flow (or ratio of mass flows), but also by its other key physical characteristic, its size distribution. Its effect on grinding circuit performance is explained. The equipment application design steps to achieve a desired circulating load, in terms of both its mass flow and size distribution, are described. Finally, its pivotal role in grind control is specified. Our goal is for the reader to come away with a fresh understanding of the role of the circulating load in wet ball milling circuits, including how and why it should be measured and managed.

Feb 22, 2026

By R. D. Smith

The Bureau of Mines (BOM) evaluated the technology, capital investment, and annual operating costs of emission control for further reductions of lead in ambient air at the East Helena, Montana, smelter, and the Glover, Herculaneum, and Buick smelter-refineries in Missouri. This study seeks to analyze the technology available to the domestic primary lead industry for attempting to further reduce lead emissions below 1985 levels. Through enclosure of concentrate unloading and handling areas and all lead-processing buildings, followed by venting these enclosures to the atmosphere through baghouses and the application of appropriate local controls, emissions can theoretically be reduced by a total of 2,424 pounds of lead per day from 1985 levels at the three Missouri operations. Using conventional technology, aggregated additional capital costs of $250,014,000 and annual operating costs of $18,507,800 are estimated for the four operations, resulting in a total cost of $0.063 per pound of refined lead. Continuous drossing techniques would assist in meeting OSHA standards in process areas. Continuous drossing would change capital and operating costs to $258,344,800 and $16,104,700, respectively, for a total cost of $0.062 per pound of refined lead. First quarter, 1986 open market price for refined lead was $0.184 per pound.

Jan 1, 1986

By M. S. Celik, G. Onal, S. Atak, A. A. Abramov

An oolitic phosphate ore composed of phosphate (mainly francolite) and carbonates as gangue has been tested for the suitability of the reverse flotation process. The samples were first ground autogeneously followed by the reverse flotation process. While the carbonates were floated by sodium oleate the phosphate was depressed by phosphoric acid. The effect of particle size, reagents type and concentration on flotation recoveries have been investigated to determine the optimum conditions. By this process, a run-of-mine ore containing 16.72 % P205 was upgraded to 28.00% P205 with a recovery of 77.0% The mechanism of optimum flotation with phosphoric acid observed at pH 6.3 is explained based on a relationship involving surface potentials and the ratio of required collector concentrations for the respective minerals.

Jan 1, 1993

By Kasimcan Koruk, Julian M. Ortiz

Building a geological model is important in resource estimation, as it defines the extent of domains for estimation. Geological models are built by assigning a domain to the samples, based on logging of different features related to lithology, alteration, and mineralization. Then, the extent of these domains is determined using geometric or geostatistical tools. However, these models should account for uncertainty, since the actual extent of these domains is not known and must be extrapolated from the labelled samples. With the availability of geochemical datasets and machine learning techniques, employing multiple variables to build resource models should be considered. This article proposes a two-step machine learning approach with an ensemble implementation to define geological domains and their uncertainties. First, an unsupervised binary clustering method labels the geochemical samples into two domains. These labelled samples are used to inform a geological domain model built by support vector classification. This application is repeated with subsets of variables and subsets of samples, leading to an ensemble learning method. Weak models are produced with each subset of samples and variables, and combined to devise a stronger learner. The final model accounts for uncertainties thanks to the ensemble implementation. The proposed workflow is demonstrated on a dataset from a porphyry copper deposit, applied hierarchically to define four domains. Performance is comparable with traditional methods, but provides the advantage of allowing domain knowledge in the selection of the variables, and generates domain boundaries that can be controlled in terms of their continuity and smoothness.

Oct 11, 2023

By W. D. Elston, A. E. McLaughlin, G. B. Hampton, W. L. Barham, J. F. Murphy, W. H. Cundiff, J. W. Mulloy, R. G. Breuer, J. W. Shaffer

Introduction Alumina (aluminum oxide) is the material from which all the world's aluminum is produced. In the Western World, all the alumina is made from bauxite by the Bayer process. In the nearly 150 years since aluminum was first isolated by Oersted, the metal has grown from a laboratory curiosity to a position of major importance in the world's commerce. In terms of annual production rates aluminum is first among nonferrous metals. Oersted's discovery-reduction of aluminum chloride with potas¬sium amalgam-was improved on by Ste. Claire Deville, whose so¬dium amalgam reduction of aluminum chloride led to the commercial production of aluminum in France in 1855. Ste. Claire Deville's method prevailed until 1886 when Charles Martin Hall and Paul T. Heroult each invented a process for the production of aluminum by the electrolysis of alumina dissolved in molten cryolite. The inven¬tion by Karl Josef Bayer in 1888 of an economical process for making very pure aluminum oxide (alumina) from bauxite established the necessary link between known ores and the Hall-Heroult reduction process. Bayer's work completed the scientific base-the ore bauxite refined to alumina by the Bayer process (U.S. Patent No. 515,895), the alumina reduced to aluminum in the Hall-Heroult cell (U.S. Patent No. 400,766--upon which today's aluminum industry is founded. Small-scale production of aluminum in the U.S. began in 1888 utilizing the Hall cell. By 1903, bauxite properties and a Bayer process refining step had been incorporated into the production activities. On this base the aluminum industry in the U.S. has grown at an annual compounded rate of 15%. Since 1946 the annual growth rate has been 10%.1 The rapid growth of the industry is the result of many factors among which are the existence of widespread bauxite ore deposits; a sound and economic production technology; and the properties of the metal-lightness, strength, ductility, good electrical and heat con¬ductivity, and pleasing appearance, which lead to ever greater de¬mands for aluminum in an industrializing society. At the inception of the industry, the only market that could be found for aluminum was in the production of cooking utensils. How¬ ever, the rapidly accelerating industrial and technological development of the Western World soon created new needs for aluminum, and today aluminum is marketed in a broad range of industrial, commer¬cial, and consumer applications. The principal uses for aluminum are:' building and construction, 22%; transportation, 18%; electrical, 13%; packaging, 11%; consumer durables, 10%; machinery and equipment, 7%; other, 19%. The 1974 production of primary alumi¬num in the world was 14.5 million short tons, which at an approximate ingot price of 40¢ per lb puts a value of $11.6 billion on the industry product prior to fabrication. While aluminum is widely distributed in the earth's crust and is a major constituent of many rocks and soils, to date no method of extraction of aluminum from such nonbauxite material has been brought to commercial practice in the Western World. In the USSR alumina is produced by the complex processing of nepheline syenite, but elsewhere all commercial production of alumina is from bauxite. A brief discussion of recent developments and other processes for alumina is included in the subsection "Other Processes for Alumina," page 19-15. In early 1973, a major U.S. aluminum producer announced the successful development of processes for the production of aluminum from aluminum chloride. This achievement promises to exert a major influence on the future of the aluminum industry. In the initial com¬mercial application of this new technology, Bayer alumina will be chlorinated, and the aluminum chloride then reduced by electrolysis. Important claims for the new processes are lower energy requirements (one-third less than obtainable in Hall cells) and reduced labor costs. Capital costs are said to be no greater than for conventional plants. While the announced intention is to produce the aluminum chlo¬ride from Bayer process alumina, the new chloride reduction process will eliminate the other raw materials, carbon and fluorides, required by the conventional Hall cells. The electrodes in the chloride cell will not be consumed on the reduction process and the electrolyte will have, as the name indicates, a chloride rather than a fluoride base. 2. Bauxite Definition and Origin. Bauxite is a naturally occurring raw material composed principally of a mixture of one or more of the hy¬drated aluminum oxide minerals gibbsite (Al2O2 3H2O), boehmite (Al2O3 H2O), and diaspore (Al2O, - H2O), and impurities of silica, iron oxide, titania, and other various elements in trace amounts. It is an end or near-end product of chemical weathering. Depending on the amount of iron impurities, the color of bauxite varies from dark red and brown to pink to white. Some bauxite is finely divided, free digging earthy material, while other forms are dense and rocky, requiring explosives in mining. Many gradational forms exist. It is one of the most variable of mineral raw materials in chemical composition and physical appearance. It is generally believed that bauxite deposits resulted from intense chemical weathering of aluminum-bearing rocks or formations under tropical or subtropical conditions with alternating wet and dry sea¬sons. Topographic conditions were favorable for drainage and the in-situ accumulation of aluminum, iron, and titanium oxides. There was low to moderate topographic relief with a minimum of erosion during long quiet periods in earth history.2 The occurrence of bauxite is widespread and it has been found on all continents except Antarctica. Production was reported from 27 countries in 1974, at which time total world production was over 79 million metric tons. Of this production 76% was from seven coun¬tries-Australia, Jamaica, Surinam, Guinea, USSR, Guyana, and Greece-which ranked in that order of production. In Table 1 are shown typical compositions of bauxite from some

Jan 1, 1985

By Ben DiFiore, Richard DePew, Nate Long, Adrian Naranjo-Castillo, Chris Petta, Robert Auber

The Walworth Run stream was brick-culverted in the 1800s, converting it to a 16-ft diameter sewer. This Cuyahoga River tributary contributed to the infamous burning river that became the catalyst for USA’s environmental movement. The NEORSD has been working hard to reduce CSOs here, most recently by diverting Walworth Run’s 882 MGD of flow to the new Westerly Tunnel. This had to consider structure age/size, alluvial/glaciolacustrine deposits (requiring several ground support systems, groundwater control), and maintenance of massive flows. This paper examines challenges identified during design that supported the contractor in development of a risk-mitigating plan, culminating to successful implementation.

Dec 1, 2022