Search Documents

By Massimo Concilia, Remo Grandori, Paolo Nardone

Paul Y. – SELI Joint Venture had been contracted to build the longest section of the Strategic Sewage Disposal Scheme (SSDS) – Stage I. This involved two tunnels under urban and marine areas excavated by high performance hard rock open type TBMs operated from deep shafts. A specific ground treatment program was developed using advance probing and grouting to control water inflow into the excavations. The article describes: the technologies adopted, the experienced problems, the encountered productions and their interrelation with the water inflow amounts, the possible improvement in the technologies for the excavation of the future stages of the same project as well of any other project under similar conditions.

Jan 1, 2001

By B. A. Slaker, T. Miller, M. M. Murphy

An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in.) was measured by the extensometers, photogrammetric reconstructions and laser scanner over a six-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls were significantly lessened.

Jan 1, 2018

By J. Peterson, P. G. McKneight, R. W. Riggle

"In today’s tough mining environment, the key difference between surviving and thriving is how effectively miners optimize their mining operations. This paper explores the compounding effects material fragmentation has on mining costs and productivity. Starting with Drilling & Blasting and moving through Loading, Hauling and Crushing, we will illustrate the opportunities to improve operating costs and thus reduce the Total Cost of Ownership (TCO) of the total mining system. Material size and volume requirements are defined by the needs of the mill or plant, and drive the rest of the mining operation from the bench through the primary crusher. At the start of the cycle, where the rock mass is drilled and blasted, the degree of fragmentation and the muck pile configuration is determined, as are the effects on cost and productivity of all subsequent operations. The cost of managing oversize material, including secondary handling, overloading, reduced diggability, higher load factors, extra pass loading, increased wear factors and reduced throughput rates are all opportunities for improvement. INTRODUCTION Having visited many mine sites, customers are asking about the end to end mining value stream from loading to the crusher and how to measure the cumulative effects on each part of the mining value chain. All too often improvements with the drilling and blasting may impact fragmentation but do not improve the diggability so the net change on cycle times or fill ratios is perceived to be negative at the point of loading but they may have a measured improvement going through the primary crusher. This makes it imperative to measure performance at each segment of the overall cycle and not just to the crusher but thru it. The mine material process originates with solid rock, in-situ, and progresses to the output of the primary crusher. Once the material has passed the primary crusher the fragmentation size will be fairly consistent and promote consistent throughput of the plant or mill. In late 2015 a team was conducting a reassessment visit to a mining site where we had conducted the original assessment the previous year. Though many recommendations had been implemented some had been so recent they had not resulted in the expected improvements. Several of our discussions kept returning to the impact fragmentation has to both the individual components of the mining cycle but also the effects compounded throughout the end to end process. Let’s move on to the big picture before we zoom in on any specific operation. To get from native solid rock in the ground to a concentrate or a saleable rock product we have the same steps from one end of the chain to the other. We start with a good geological understanding of the rock type, characteristics and structure to design a program to drill and blast the rock. The height of the bench is relevant to the annual production requirements and the specific digging equipment models best sized to make that production possible. The equipment selection influences the bench height which has a minimum and maximum hole diameter to maintain a safe blasting operation. The diameter of hole burden and spacing all contribute to a good distribution of explosives in the rock mass that maximize the fragmentation and preconditioning of the rock when blasted. The timing and sequencing of hole initiation will yield a fragmentation ratio and diggability factor. Fragmentation size adjustments will change the meters drilled per cube and the explosives consumption will change accordingly. Drill cost is measured by meter drilled so a direct relationship exists between cost and fragmentation sized achieved."

Jan 1, 2017

By R. C. Troxell

Alternative methods of analyzing data acquired by the Morenci copper concentrator process control instrument-computer system are presented. Experimental measures of ore characteristics, for proposed feed forward control, are introduced. These include on-line indexes of ore hardness, ore density, ore dusting, and ore color. Comparison of metallurgical results before and after computerized process control implementation, allowing for differing ore grades, oxidation, hardness, and fineness of grind, also is described.

Jan 1, 1979

By T. Bauerle, G. Poplin, Z. Dugdale

"The issue of mine worker fatigue is as complex as it is understudied. Generally, worker fatigue lies somewhere on a continuum between psychology and physiology, which makes the measurement and management of it difficult with no easy solutions for operators or workers. Answers to even basic questions remain elusive—such as what is fatigue, how is it measured, and how can organizational resources reduce fatigue—and answers seem to present no single, clear path to action for the health and safety of the worker. This manuscript supplements the growing body of interest in the problems of fatigue in the mining industry by reviewing some of what is known about worker fatigue in general and in the mining industry in particular. The material covered here includes basic topics of the hows and whys of worker fatigue; an overview of fatigue models, findings, and evidence-based solutions with a focus on mining; and potential future directions aimed at mitigating miner fatigue. INTRODUCTION “It is recommended that the whole fatigue test problem be stated in a form the nature of which may be indicated by the following suggestions: that the term fatigue be absolutely banished from precise scientific discussion, and consequently that attempts to obtain a fatigue test be abandoned [emphasis added].” – Bernard Muscio, Pioneer Australian Philosopher and Industrial Psychologist, in a 1921 Report to the Cambridge Industrial Fatigue Research Board Fatigue presents several challenges for the mining industry. Depending on the specific occupation, daily work, or operational setup on any given mine site, mining jobs can have a fair amount of labor-intensive tasks mixed with monotonous and repetative duties. Combined with the long working hours and shift-work schedules of mining work, the prevalence of fatigue in mine workers may seem rather unsurprising. On the one hand, mining is certainly not alone in facing the challenge of addressing worker fatigue. Indeed, many of the characteristics above mirror the similarities of fatigue in other industries, such as health care, aviation, and security. To the extent that fatigue in mining acts like fatigue in any other industry, then any fatigue management applications, trainings, or interventions in existence can be borrowed from other industries and applied to mining in a “cookie-cutter” approach. On the other hand, some have argued that mining in particular is especially susceptible to increases in the prevalence of fatigue beyond the characteristics listed above due to the multifaceted combination of factors in mining environments associated with fatigue: dim lighting; limited visual acuity; hot temperatures; loud noise; highly repetitive, sustained, and monotonous tasks; shiftwork; long work hours; early morning awakenings; and generally poor sleep habits (Canadian Centre for Occupational Health and Safety, 2012; Legault, 2011). Legault (2011) in particular argues that it is the combination of these factors simultaneously that can make mineworkers particularly susceptible to sleep deprivation and fatigue in comparison to other industries where these factors are often not present alltogether. If fatigue looks and acts different in mining, as others have argued, more research is needed to determine if, how, and why worker fatigue might need to be managed differently in mining."

Jan 1, 2018

By Mike Ghassemi

It is clear that precise overground and under-ground mapping is an important factor for all designers. Due to rapid changes in underground construction, tunnel designers are increasingly in need of updating project information. This article explains the latest techniques for detecting under-ground utilities as well as underground mapping. Global Positioning System (GPS) is a very ac-curate and popular navigation and mapping system that has been used extensively above ground, but is not used for underground mapping as signals are not strong enough to pass through ground or water. Most underground techniques were developed for military applications during the first and second world wars. Later, the techniques became public. For example, ground penetrating radar was developed for the military in 1970 to be used for locating tunnels under the demilitarized zone between North and South Korea. Later, the same technique was used for detecting unexploded ordinance such as plastic land mines.

Jan 1, 2011

By M. J. Gregory

The Pebble Cu-Au-Mo deposit in southwest Alaska is one of the world's largest porphyry deposits. The western part of the deposit was discovered by Cominco America in 1987, who sold the project to Northern Dynasty Minerals Ltd., in 2001. Northern Dynasty discovered the high-grade eastern part of the deposit in 2004 and went into a 50:50 partnership with Anglo American PLC in 2007, forming the Pebble Limited Partnership (Lang et al., 2008). The Pebble Limited Partnership has continued to delineate the deposit through diamond drilling with the most recent resource estimate released in February 2010 (Pebble Limited Partnership, 2010). The Pebble deposit mineral resources comprise 5.94 billion tonnes of measured and indicated resources grading 0.78% Cu EQ, containing 55 billion pounds of copper, 67 million ounces of gold and 3.3 billion pounds of molybdenum. Also delineated are 4.84 billion tonnes of inferred mineral resources grading 0.53% Cu EQ, containing 25.6 billion pounds of copper, 40.4 million ounces of gold and 2.3 billion pounds of molybdenum (Pebble Limited Partnership, 2010). Resources are calculated using a 0.3% Cu EQ cutoff. GEOLOGY AND MINERALIZATION Deposit Geology The Pebble deposit is located in the Kahiltna terrane, between terminal strands of the north-east-striking Lake Clarke strike-slip fault. This fault represents an accretionary boundary and separates the Kahiltna terrane to the north-west from the Peninsular terrane to the south-east (Lang et al., 2008). The Pebble deposit represents a large magmatic-hydrothermal system centered on a group of 90 million year old porphyritic hornblende granodiorite intrusions. An east-west cross section through the southern part of the deposit (Figure 1A) shows the typical relationships between the various rock units which host sulfide mineralization. Sub-parallel ~96 million year old granodiorite and diorite sills were intruded into siltstones of the Jura-Cretaceous Kahiltna flysch. In the west, these sills were cut by a ~96 million year old alkalic intrusive complex composed of porphyritic monzonites and monzodiorites and related intrusion breccias (Bouley et al, 1995). The mineralized 90 million year old hornblende granodiorite intrusions cut all rock types and comprise four small stocks in the western part of the deposit and a larger pluton in the eastern part of the deposit. Recent deep drilling indicates that these intrusions coalesce at depth. The strongest porphyry-style mineralization is centered on the eastern granodiorite pluton and extends into the surrounding rock units (Figure 1A). The western half of the deposit crops out at surface, whereas the eastern side is un-conformably overlain by a cover sequence of Late Cretaceous to Eocene sedimentary and volcanic strata. The deposit was tilted 20º to the east during the Eocene.

Jan 1, 2012

By Zoltan F. Oszter

The frictional resistance to motion of a belt conveyor has always been a subject of intensive studies and research by engineers throughout the years. Numerous informations have been developed by analysing series of field tests on belt conveyors of different characteristics and carrying different materials at various capacities. Within certain limits of weight per unit length and tension, the theoretical considerations and the analysis of the field tests, both in the US and abroad, resulted in the development of similar formulas. In general these formulas are safe to use up to the following limits:

Jan 1, 1977

By C. Athanassopoulos

Geomembranes have been used in the mining industry since the early 1970s in solution and evaporation ponds, tailings impoundments, and heap leach pads. Traditionally, heap leach pad lining systems have consisted of a single geomembrane liner placed directly over a prepared subgrade of locally available soil. Heap fills are constructed by placing a layer of highly-permeable drainage stone (overliner) over the geomembrane. Crushed ore is then placed on the leach pad in 3- to 10-m (15- to 30-foot) thick lifts, sometimes reaching final heights of several hundred feet. The crushed ore is irrigated with a chemical solution which dissolves the precious metals from the ore. The nature of the chemical leaching solution depends on the metal being targeted. Low pH sulfuric acid solutions are generally used to leach copper and nickel; high pH cyanide solutions are used to leach gold and silver. The metal-laden pregnant leach solution (PLS) passes down through the ore pile and is captured in a drainage system. Metals are extracted from the leach solution and the solution is then recycled back onto the leach pile. When under load, geomembranes are vulnerable to damage from large stones both in the soil subgrade and in the overlying drainage layer. Although intact geomembranes are virtually impermeable, installed geomembranes will have a small number of holes due to imperfect seams or damage during construction and filling operations. These holes serve as open pathways for leakage into the soil below. Smith and Welkner (1995) estimated liner leakage rates ranging from 5 to 10,000 L/ha/day, depending on the type of heap pad liner and level of construction quality assurance (CQA). Thiel and Smith (2003) reported liner leakage rates up to 2,000 L/ha/day for a valley fill facility with heads ranging from 15 to 35 m.

Jan 1, 2011

By J. Payton

Public Service Company of Oklahoma began burning sub-bituminous coal in December, 1979. Initially PSO had a single source coal supply from Jacobs Ranch Mine, and in 1982 added deliveries from Clovis Point mine. Both are Powder River Basin (Wyoming) coal mines. In 1986 PSO began burning Oklahoma coal to meet Oklahoma's 10% native use law. PSO experienced random s lagging during certain blends of these coals. PSO installed a boiler performance system to help control the slagging problems from the various coal blends, to improve boiler efficiency, and increase total coal consumption.

Jan 1, 1990

By David D. DiPonio, John DiPonio, Roger Van Omen

The greatest opportunity to attain the most favorable prices for underground construction projects occurs during the competitive bidding period. The Owner, Engineer, and Contractor need to have a thorough understanding of the project’s design concept, how it is going to be built, and what it is going to cost. This paper presents the opinions of three engineering professionals who are well established in their sectors of heavy civil underground public works construction. This paper will outline and summarize the considerations that the three principal contracting parties of Owner, Engineer, and Contractor need to make to obtain good price quotes at the time of bids.

Jan 1, 2005

By J. F. Burr, D. Snyder, W. Calder

"INTRODUCTION “Explosion protection” refers to techniques used to minimize the potential for electrical and electronic equipment to create an ignition while operating in a hazardous location (HAZLOC). In particular, U.S. coal mines are required to use equipment in certain areas of the mine that has been approved by the Mine Safety and Health Administration (MSHA) for use in a methane and coal dust environment to limit the risk of the equipment creating an ignition-capable spark or a thermal energy ignition. In general, MSHA’s regulations for explosion protection recognize two techniques: the use of explosion-proof enclosures (XP boxes) and 2-fault intrinsic safety for electrical and electronic equipment. For 2-fault intrinsically safe (IS) equipment, the U.S. mining industry requirements are unique in that the equipment is certified by MSHA. The criteria MSHA uses to evaluate equipment for intrinsic safety, as required by Title 30 of the Code of Federal Regulations (30 CFR) [30 CFR, Sections18.20(b), 18.68(a)(1), 19.1(b), 20.1(c)(2), 22.6, 23.6, and 27.20(a)], is published in a document referred to as ACRI2001 (1). Outside of U.S. underground mining, many industries and countries accept equipment that is designed to a consensus-based international standard (ANSI/ISA 60079-11 is the U.S. version). The purpose of this study is to provide an overall assessment of the ANSI/ISA 60079-11 standard on 2-fault intrinsic safety and the MSHA ACRI2001 acceptance criteria, and determine if the ANSI/ISA document can be an alternative to ACRI2001 while maintaining an equivalent or better level of safety for miners. There are many drivers for this study. First, immediately after the 2006 MINER Act (2) was passed, there was a perception in the industry that the unique MSHA requirements were contributing to delays or restricting the availability of equipment to meet the requirements of the Act. Additionally, the MINER Act required that mine operators submit an accident response plan for MSHA approval, to be reviewed every six months. MSHA is required to determine if these plans reflect the most recent credible scientific research and make use of currently commercially available technology. There is a concern, as expressed in a recent National Academy of Science (NAS) study (3), that the unique requirements for U.S. mining may be limiting the technologies available to coal miners and technology options for mine operators. Accordingly, the study recommended that the National Institute for Occupational Safety and Health (NIOSH) and MSHA re-examine their technology approval and certification processes to ensure they are not deterring innovation, and explore opportunities to cooperate with other international approval organizations to harmonize U.S. and international standards without compromising safety. Lastly, the National Technology Transfer Act (NTTA) and the accompanying Office of Management and Budget’s OMB-119 circular mandate the use of consensus-based standards by federal agencies. However, for U.S. mining operations, MSHA cannot accept such standards unless a determination is made that such standards provide an equivalent level of protection for the miner, per the requirements of the 1977 Mine Act, the 2006 MINER Act, and 30 CFR Part 18 regulations."

Jan 1, 2017

By Robin J. Hickson

El Abra is one of the world’s premier copper de-posits. The project is located in northern Chile, 140 km (87 miles) inland from the Pacific coast. It has the same geologic age and structural setting as the world-class Chuquicamata copper mine located 42 km (26 miles) to the south. The current development plan for El Abra extracts798 Mt (879 million st) of high-quality oxide ore. This will require building a solvent extraction/electrowinning(SX/EW) facility that can produce 225 kt/a (248,000stpy) of cathode copper. This will make El Abra the largest SX/EW copper operation in the world, and the world’s seventh-largest copper producer.

Jan 1, 1996

By S. E. Phillipson

Four massive pillar collapses in limestone mines, and one in a marble mine, occurred between 2011 and 2021 in benched areas at the Appalachian physiographic province. We characterized the rock mass at 43 limestone mines using the Geological Strength Index and, by plotting the results on a physiographic relief map, determined that GSI values between 55 and 70 preferentially occur in the Appalachian and Ouachita Mountains, which were subject to deformation during the Ouachita and Alleghanian Orogenies. Limestone mines located in formations of similar age in the Interior Plains, where deformation was less developed, are characterized by Geological Strength Index values over 80. We present the results of pillar strength calculations that incorporate the Geological Strength Index from mines that experienced massive collapse, as well as from mines with benched areas that did not collapse, to demonstrate the negative effect that a jointed rock mass has on pillar stability. We suggest that pillar designs, particularly those in which benching will be incorporated, should include allowance for rock mass quality. Because of the preferential dominance of lower GSI values in the Appalachians, we further suggest that pillar designs in this environment may require additional engineering assessment, especially where benching is intended. Lower GSI values may often translate into greater overbreak, which results in loss of pillar volume, corresponding wider back spans, and a decreased width-to-height ratio.

Jun 25, 2024

"Cast blasting is the primary means of overburden displacement in a surface coal mine. It serves two purposes; fragmenting the rock and throwing it directly to its spoil pile using explosive energy. Increased throw minimizes costs by reducing the amount of material that needs to be rehandled. Prior studies have shown that by only changing blasthole timing with the same blast design, fragmentation and throw alter. It is necessary in cast blasting to optimize both fragmentation and throw, since larger fragments will require more wasted energy to throw the same distance. In an operating mine in Georgia, an optimum interhole delay for fragmentation has been found by studying timings from 0 millisecond (ms) to 45 ms. Instantaneous timing between holes increased the throw by more than 31 m (100 ft), but fragmentation was poor. Shock and detonation wave collision is a potential reason for this increased throw.Explosives are utilized extensively by the mining industry in order to break rock, as either ore or overburden, for hauling, loading and crushing. An effective production blast strives to achieve optimum rock fragmentation in order to increase the efficiency and reduce the costs of those downstream operations, while simultaneously meeting environmental regulations. The goal of blasting with respect to fragmentation is, according to Hettinger (2015), “to decrease the average particle size of the fragmented rock without overly increasing fines or, in other words, improve fragmentation.”Additionally, the distance the rock is transported by the explosive energy from the blast, also known as throw, can increase efficiency by reducing the amount of material that is rehandled by mine equipment. The primary situation in which this is desirable is the cast blasting of overburden across the narrow pit of a surface coal mine. A key variable in a blast design pattern that can be manipulated to optimize both fragmentation and throw is delay timing between detonations. The invention and increased utilization of electronic detonators have allowed for precise delay timings to be used between rows, holes and even multiple primers within the same hole. These recent developments in the blasting community have also provided an opportunity to investigate whether or not the mechanism of shock or detonation wave collisions caused by short timing delays are responsible for any increased fragmentation or throw. This experiment attempts to demonstrate if an increase in throw can be achieved while maintaining optimum fragmentation."

Jan 6, 2017

By QINGXIANG CAI, Lin Li, PENG LIU, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, YONGLI ZHOU

Green mining is the latest technological advancement to reduce mining’s environmental impact with minimal energy and resource consumption. Green mining — aimed at protecting nature and providing socio-economic benefits — is a multifaceted network of its connotations and key indicators. China has not yet defined its connotation and formed an effective evaluation system for surface mining. We defined its connotation and developed an evaluation index system based on the theory of green grades. As the indicators are selected based on extensive research, they express the advantages and disadvantages of various aspects of a mine. The index is composed of three attributes (safety, efficiency and environment), nine criteria and 35 indicators. The indicators were quantified according to experts’ opinions using the fuzzy comprehensive evaluation method. The results of a case study show that the environment is the most critical aspect, followed by efficiency and safety. This study can provide technical support for the development of green mining.

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques had been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

By E. D. Attanasi, J. H. DeYoung

Several factors contributed to continued declines in mineral-exploration activity in the US in 1985. Low metal prices and, what appears to be worldwide chronic excess capacity in copper, molybdenum, lead, and uranium, have resulted in mineral-exploration expenditures remaining anemic. Economic recovery could result in a healthier mining industry and more cash flow to fund exploration. This is because general economic activity and US mining industry activity have historically been closely linked. However, as the worldwide economic recovery has expanded, the mining sector has continued its downward slide. New cuts in industry exploration budgets in 1985 shocked those who thought the exploration situation could not become worse. Some personnel and equipment had been redirected from base metals exploration to precious metals in the past few years. Last year, continued reductions in exploration sent many professionals out of the mining industry. Recent staff reductions or consolidations of operations were made by Noranda, Chevron, Molycorp, and other exploration companies. The latest data from the Society of Economic Geologists (SEG) summary of exploration statistics show that professional staff at year end in major US exploration companies (domestic and foreign operations) fell from 2355 in 1981 to 1868 in 1983 and 1277 in 1984. By the end of 1985, two economic trends were established that could improve the future profitability of mining and hence exploration. First, the price of crude oil began a decline. If sharply reduced energy prices increase worldwide economic expansion, the substantial excess capacity in some of the base metals industries could disappear, and prices could improve. Furthermore, if energy price declines reduce mining and processing costs significantly, metals may recapture some lost markets. The decline in oil revenues has already encouraged some oil-producing countries, such as Venezuela, to look toward development of mineral resources to earn foreign exchange for debt repayment. Second, the decline of the dollar by 21% during 1985 could also help US producers meet foreign competition. During 1985, industry restructuring continued as many oil companies sold off mining subsidiaries and minerals properties. Gold, silver in new discoveries Precious metals continued to dominate the announcement of new discoveries and exploration projects in 1985. A review of domestic exploration and development activities reported in several industry journals shows that 60% to 80% of these projects were directed primarily at precious metals, particularly gold. Base metals exploration activities frequently involved polymetallic deposits with gold or silver values. Because much of this exploration was done on identified targets (on-property exploration), the decrease in wildcat or grassroots (off-property) exploration may be more substantial than indicated by reductions in total exploration activity. Significant gold discoveries in 1985 included several in Nevada, among them the Genesis property of Newmont (near the Carlin mine), Goldfields' discovery of the Chimney deposit in Humboldt Co., and Freeport's discovery of two mineralized sites near Jerritt Canyon. Gold exploration continued to be focused in the western US and Alaska, but gold production starts at the Haile mine in South Carolina, and the Ropes mine in Michigan as well as Amselco's feasibility studies on deposits near Ridgeway, SC, are evidence that gold exploration is not limited to the West. The dominance of gold projects in exploration is not limited to the US, as demonstrated by gold dis¬coveries and exploration projects in Australia, Brazil, Canada, the Caribbean region, China, Guinea, Ivory Coast, South Africa, the South Pacific islands, and Thailand. From the standpoint of US metal miners, it is perplexing that worldwide exploration and development is also taking place in copper, zinc, tungsten, and other metals with depressed prices. During 1985, the US Geological Survey's efforts to map the sea floor of the Exclusive Economic Zone shifted from the Pacific Coast to the deep water areas of the Gulf of Mexico and to areas off the coast of Puerto Rico and the Virgin Islands. An atlas containing sea-floor maps of the west coast area was published as US Geological Survey Miscellaneous Investigations Series Map 1-1792. Results of the 1985 surveys are expected to be published by January 1987. Exploration trends - Statistical evidence Data from the SEG showed continued decline in the US mining industry's exploration expenditures through 1984. The share of US companies' domestic exploration expenditures directed toward base and precious metals has increased from 51% to 84% from 1980 to 1983 and to 86% in 1984. US mining companies spent about $0.67 of each exploration dollar in 1984 in the US. However, this represents an increase from earlier years. The 1983 data also show that firms spending more than $5 million on exploration accounted for 77% of exploration expenditures. Since 1981, the Bureau of Land Management (BLM) has been assembling data on claims and an-

Jan 5, 1986

Like the Summer Olympics and U.S. presidental elections, MINExpo comes along once every four years. More than 35,000 people attended the last MINExpo and there is talk that there will be more this time. Just about every company that has anything to do with mining, 1,822 to be exact, will exhibit their wares at the show, but it is the ones rolling in the massive equipment that make MINExpo the show that it is. The following is a glimpse at some of the companies and equipment that you can expect to see at this year?s MINExpo.

Jan 1, 2012

By C. V. Deutsch, D. A. Silva

The geologic modeling of multiple domains is required for the prediction of mineral resources and reserves. In general, explicit methods have wide acceptance among modelers due to the ability to manually add deemed important trends and geological features into the models. As an alternative, implicit geologic modeling techniques are increasingly adopted to reduce professional time requirements. These methods aim for objective, repeatable and flexible models by replacing the manual time-consuming interpretation of sections with the interpolation of signed distance values. These techniques, however, have been developed for the binary case of two domains at a time. The current paper presents an algorithm that extends the binary case to multiple domains. The method is able to transfer large-scale geological features from data to geologic models. A case study illustrates the benefits of the algorithm and practical implementation considerations.

Jan 1, 2016