Search Documents

By L. Malmgren, A. Ansell

This paper deals with the influence from blast induced stress waves on the performance of shotcrete support in the Kiirunavaara mine. Time histories of stress waves from blasting were obtained from measurements during production blasts in the mine, followed by failure mapping. A finite element model, consisting of beam and spring elements, was used to calculate the shotcrete response to vibrations from blasting. The modelling approach was similar to that of a building during an earthquake, with accelerations measured in-situ used as loads. The analysis showed that the calculated adhesive stresses exceeded the strength in the interface between rock and shotcrete near to the blasted ring. It also indicated that tensile rock failure did occur. These types of failure will presumably result in ejection of joint defined rock blocks or rock slabs and will require a ductile support, such as fibre reinforced shotcrete. The predicted failure was confirmed by the mapping, which also showed that the zone of failed shotcrete was much larger in areas with plain shotcrete compared to areas with reinforced shotcrete. L’influence de l’onde de pression générée par les sautages à la mine de fer de Kiruna sur la performance du béton projeté est étudiée dans le présent article. Les ondes créées par les sautages ont été enregistrées et les domages résultants ont été cartographiés. La réponse du béton projeté aux vibrations de sautage est étudiée à l’aide d’un modèle d’éléments finis, constitué de poutres et de ressorts. L’approche est similaire à celle d’un immeuble subissant un tremblement de terre, avec les accélérations internes utilisées comme charges. L’analyse montre qu’à proximité des sautages, la contrainte adhésive dépasse la résistance de l’interface roche-béton. L’analyse confirme aussi l’existence de ruptures en tension. Ces types de rupture induisent probablement l’éjection des blocks définis par les structures du massif rocheux et requierent un support ductil, comme du béton projeté renforcé par exemple. Le type de rupture est confirmé par les observations de terrain, qui montrent aussi une extension plus importante des domages lorsque le béton projeté n’est pas renforcé. In diesem Konferenzbeitrag geht es um den Einfluss, der aus einer Sprengung hervorgerufenen Schwingungswellen auf die Ausführung der Spritzbetonverstärkung in dem Kiirunavaara Bergwerk. Die Aufzeichnungen der Schwingungswellen von Sprengungen gemäß einer Fehlerkartierung beziehen sich auf Messungen, die während der Sprengungen durchgeführt wurden. Ein Finite Elemente Modell, bestehend aus Stab- und Federelementen, wurde für die Berechnung der Spritzbetondeformation in Bezug auf die Schwingungen aus Sprengungen angewendet. Die Modellierungsmethode war ähnlich der eines Gebäudes während eines Erdbebens anhand der gemessenen Beschleunigungen vor Ort, die als Lasten benutzt wurden. Die Untersuchung hat gezeigt, dass die berechnete Haftspannung größer war als die Festigkeit in der Verbindung zwischen Gestein und Spritzbeton in der Nähe des Sprengungscentrums. Die Analyse hat gezeigt, dass die Zugfestigkeit des Gesteins versagte. Diese Arten von Versagen werden als Folge der Herausnahme von Gesteinsbrocken oder Gesteinsplatten erklärt und benötigen eine faserverstärkte Spritzbeton. Das vorausgesagte Versagen bestätigte sich beim Kartieren, welches auch zeigte, dass die Zone des versagenden Spritzbetons in Bereichen mit unverstärktem Spritzbeton viel größer war als in Bereichen mit armierten Spritzbeton.

Jan 1, 2003

By A. V. Pavlov, V. A. Grygorian, Kossyrev, A. E. Semin, A. Korostylev

A new way of producing low-silicon ferrosilicon from iron-ore materials in a new type of aggregate-oxygen reactor is presented. The oxygen reactor process is based on using the calorific combustibility and reducibility of carbon materials inside the aggregate. The key to the process is successful post-combustion of carbon monoxide above a layer of a solid coke bed. Initially the possibility of production of grades of ferrosilicon containing 20 to 25% Si (FeSi20-FeSi25) was studied on a laboratory model of the oxygen reactor. Quartz sand and iron ore concentrates (from Russia and India) were used in the laboratory tests. This test work demonstrated that a ferrosilicon grade FeSi15 could be obtained directly from raw iron ore (containing 75.9 % Fe2O3 and a maximum of 23.8 % SiO2) without using rich iron-ore concentrates. The process was successfully tested on a pilot furnace at Serovsky metallurgical plant. Very promising results and efficiency parameters were achieved. The consumption of materials for 1t of ferrosilicon (15 % Si) production was as follows: 1567 kg raw iron ore, 591 kg of coal (in a composition of ore-coal briquettes), 299 kg of coke (for coke bed formation), and 815 m3 of oxygen.

Jan 1, 2004

By P. Altounyan

Techniques used to safely control the roof in UK coal mines for some 10 years have been applied to a South African coal mine. This new approach known in the UK as advanced rockbolting technology, is based on applying four fundamental principles: ?Understanding the roof failure mechanisms ?Using an effective roof support system ?Designing this support using measurement ?Monitoring the performance of the system. The paper summarizes the approach in detail and describes how it is being applied by Anglo Coal, giving results obtained to date. Investigations at a number of South African coal mines, including stress measurements at two Anglo Coal mines, have confirmed that the mode of roof failure (lateral shearing due to horizontal stress) is the same as in other coalfields worldwide, and aspects of current world best practice, including the use of advanced technology rockbolting, are therefore relevant in South Africa. The stress measurements indicated a high level of stress field anisotropy and further investigation of stress conditions in South African coal mines is recommended. The most effective bolting system to resist shear failure is one with high bond strength and stiffness. Short encapsulation pull testing of existing South African systems confirmed that they have low bond strength and stiffness. An improved rockbolt system with the required performance, and features allowing rapid installation and installation quality and performance audit, has been developed and is currently under full-scale trial. Design by measurement and routine monitoring procedures including the use of a rotary telltale device are also under trial. It is anticipated that South African coal mines will be able to obtain significant safety and productivity benefits from the application of this technology.

Jan 1, 2001

By L. A. Cornish, L. H. Chown, M. Matema, R. Süss, L. Glaner, A. Douglas

Mintek has been developing Pt-based alloys for high temperature applications in aggressive environments, for example, land-based turbine engines, to replace the currently used nickel-based superalloys (NBSAs). The Pt-based alloys have a similar structure to the NBSAs, and since Pt is more chemically inert and has a higher melting point, the Pt-based alloys can potentially be used at higher temperatures. The greater chemical inertness of the Pt-based alloys compared to the NBSAs means that coatings can be simpler, or perhaps not even used at all, depending on the environment. TEM work was done at NIMS, Japan, to investigate the changes in the microstructure o f Pt-Al and Pt-Al-Ir alloys at elevated temperatures using in-situheating up to1100°C. Initial casting trials showed that work needs to be done to optimise casting parameters before commercialisation can take place. Room temperature tensile tests were performed and results were variable mainly due to microstructural differences. The alloy hardnesses were in the order of 300-350HV with ultimate tensile strengths of ~800 MPa and elongations of less than 10%. These results are comparable to other alloys used at high temperatures, which is very encouraging. Keywords: platinum, super alloys, hardness, tensile

Jan 1, 2006

By J. Kerr

The first stage of the development of a new modified 201-type low nickel austenitic stainless steel is described in this paper. The alloy is intended for use as a structural alloy, and so requires a yield strength >400MPa as well as acceptable weldability and toughness. The low nickel content will give a lower material cost in comparison to more conventional austenitic grades, and the processing route is required to be similar to that of Type 304 to keep the processing cost low. The base alloy was designed using empirical methods developed for stainless steel, and the properties of the base alloy were verified using a range of small-scale melts. The base alloy had a 0.2% proof strength of ~320-400MPa, and so it is planned to use V additions of ~0.15% to bring about precipitation strengthening in the hot rolled condition, so raising the alloy?s proof strength above the 400MPa minimum.

Jan 1, 2004

By I. Bock

Selective Blast Mining (SBM) makes use of milli-second sequential blasting technology to separate the valuable reef material from waste rock in the blasting operation at stope faces in the mining of tabular ore bodies such as exist in the gold and platinum mines in South Africa. The waste rock is cast blast to the back of the stoping area, and the reef material is fractured and deposited close to the stope face. Only the reef material is transported to the surface. A simplified economic model is presented to evaluate the economic benefits of SBM. Although premature, in that adequate experimental demonstration of the validity of the model has not yet been possible, the model is presented since it indicates substantial benefits in the case of narrow reef gold mines. It is suggested that many marginal mines should seriously consider SBM. Benefits can also be realised in platinum mines, but a lot more experimental work is necessary to establish cost parameters more reliably. Some practical experience in the use of SBM in the mining of the UG2 reef is presented.

Jan 1, 1998

By A. S. Macfarlane

Mineral resource management (MRM) practice has developed in South Africa over the course of the last ten years, with the purpose of integrating previously isolated technical functions into a value chain aligned, process organization, responsible for mine planning and optimization. The implementation of MRM within various companies has met with varying degrees of success, often resulting in incremental improvements in the planning process and, conversely, often becoming the scapegoat for poor delivery on plans and projects. The reason for this has been, amongst others, a lack of a suitable metric to define the success rate of MRM in the business at hand, in terms of its contribution to the bottom line. This paper is the result of extensive research by the author into this subject, which has resulted in the conclusion that economic value added is an appropriate measure that will lead to real optimization and value creation in mining companies, if applied within a new, holistic model

Jan 1, 2006

By O. F. Ochonogor

Laser metal deposition (LMD) is an additive manufacturing technique whereby a stream of metal powder is consolidated by a focused laser beam on the surface of a substrate or engineering component. The interaction zone between the laser beam and powder particles is scanned superficially, generating tracks of deposited material. The tracks are overlapped in a deposition strategy in accordance with slices of a CAD model. Successive layers of material are built up to fabricate a near net shape part. In this work, the technique is used to fabricate metal matrix composites (MMCs) by using an elementally blended feedstock combining metal and ceramic powders in the melt pool, which melt and solidify to create the required morphology. Ti6Al4V + TiC MMCs were produced with 10, 20, and 30 vol.% reinforcing ceramic, and Zr + TiC MMCs were fabricated with 10, 20, and 30 vol.% TiC. The deposited thin walls were analysed using optical microscopy, scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS), and indentation testing. In both systems, the analysis revealed the presence of partially melted TiC particles embedded in the metal matrix along with fine dendrites of re-solidified ceramic. The dendritic structures in the Ti-based composites were confirmed as TiC, whereas in the Zr-based composite the Zr metal reacts with theTiC to form ZrC, leaving Ti in solid solution. Both the MMCs show an increase in microhardness with increasing ceramic (carbide)content, reaching a peak HV0.1 value of 500 in the Zr- based MMC and HV0.1 of 550 in the Ti based MMC.

Jan 1, 2012

By M. J. Little

Potgietersrust Platinums Ltd (PPRust) is Anglo Platinum?s only open pit operation. The major slope stability concern at PPRust is rapid, small-scale brittle failure on the west wall of Sandsloot open pit. In order to improve safety and mine more economically, a comprehensive slope monitoring strategy has been implemented. In the last 3 years four new state-of-the-art monitoring systems have been installed namely an ISSI microseismic monitoring system, a GeoMoS automated prism monitoring system, prismless Riegl laser scanners and a GroundProbe slope stability radar (SSR). Groundwater monitoring and visual monitoring have also been improved over the same time period. To complement the visual inspections, SiroVision digital photogrammetry is now used for predicting where future failures may occur. All these monitoring tools provide primary monitoring which is used to identify high risk areas. The SSR is then set up in that area to provide early warning of failure so evacuation can be successfully done. Fault tree analysis has proved that with this comprehensive slope monitoring strategy the geotechnical risk at PPRust is greatly reduced, allowing mining to continue safely and economically in challenging conditions.

Jan 1, 2006

By J. H. Van Reenen, H. Thiele, C. Bergman

For some time spirals have been the process equipment chosen to recover metal in the size range 0.15 to 3mm from ferrochrome and silico/ferro manganese slags. Recoveries of metal obtained using spirals are usually about 70%. Spirals are also difficult to control. By combining a novel gate on the Apic pneumatic fines jig with the recently developed Apic classifier, metal recoveries of 76% and grades of over 90% have been obtained for FeCr and SiMn slags in the size range 0.15 to 3 mm. The paper compares classifier operating performance and costs with those spirals for FeCr and SiMn metal recovery from slags. The classifier technology can also be applied to chromite and iron ores and coal fines.

Jan 1, 2004

By A. T. Visser

"SynopsisAlmost 20 years have passed since the cutting-edge research by Thompson and Visser on the design and management of opencast mine haul roads was conducted in South Africa. This system is based on three principles, namely the structural ability to support the ultra-heavy truck loads, the selection of vehicle and environmentally friendly riding surface, and an appropriate level of maintenance to counteract wear and tear. Obviously, proper layout and geometry are essential.These principles have been implemented worldwide, and it is useful to review the lessons learned. The objectives of this paper are to present a critical review of the status of mine haul road design and management, and the impact that these principles have made on operations, particularly the cost-effectiveness. The paper briefly reviews the principles of the haul road design and management and the extent to which they are applicable. Case studies of a number of implementations are presented to demonstrate that the principles are sound and have been applied effectively. For example, at an international operation the transport cost of coal was 40% more expensive than anticipated in the feasibility stage, and this made the mining operation uneconomic. Correction of this problem resulted in a viable enterprise. Although designed for opencast operations, the principles are equally valid for underground operations, and initial development work will be discussed.The main conclusions are that the research approach is valid and its effectiveness has been demonstrated in a number of applications. The anticipated financial benefit has been derived, and has made the mining operations that used the principles more effective. Of major importance is the application of opencast haul road design principles to the future thrust of using driverless vehicles in opencast and underground mining, where the road quality is not negotiable as there is no driver that can avoid obstacles or severe road deterioration.IntroductionAlmost 20 years have passed since the cutting-edge research by Thompson and Visser on the design and management of opencast mine haul roads in South Africa (Thompson and Visser, 1996a, 1996b, 1998, 1999, 2000a). This system is based on three principles, namely the structural ability to support the ultra-heavy truck loads, the selection of vehicle and environmentally friendly riding surface, and an appropriate level of maintenance to counteract wear and tear. Obviously, proper layout and geometry are essential."

Jan 1, 2015

By T. J. Otto, I. D. Ungerer, G. C. Lindeque, T. J. van Heerden

Anglo American Kumba Iron Ore (Kumba) continues to implement technologies focussed on improving safety and productivity; this forms part of the groups FutureSmart Mining initiative. The paper provides insights into the implementation of three technology solutions that improves the productivity of heavy mining equipment (HME). Enhancements to the short term mine planning (STMP) process, the effective use of a fleet management system (FMS) and the deployment of drones or Remotely Piloted Aircraft Systems (RPAS) are discussed. The implementation of these and other technologies contributed to a 13% and 22% increase in the overall equipment efficiency (OEE) of the primary HME at Kumba’s Sishen and Kolomela mines respectively. Four key success factors (KSF) are highlighted namely that Kumba’s technology implementation drive is a key enabler to the company’s strategy, has a strong focus on value-add, is underpinned by a holistic and integrated implementation approach and is people-centric.

Sep 1, 2021

By B. R. Broekman, K. J. R. Ford

Over the last decade significant development and use has been made of a simulation model that describes the HCFeMn smelting operations in Assmang Ltd. This spreadsheet based, semi-empirical, predictive model is derived from data from the submerged arc furnaces at Assmang?s Cato Ridge, KwaZulu-Natal smelter site. Departures from the empirical base case mass balance due to changes in the ores, reductant feeds and operating parameters are accounted for by use of fundamental relationships and heuristic type ratios which are applied in an iterative manner in the model. The model performs a sequential set of calculations to iteratively converge on a fully consistent mass and energy balance solution, which predicts Mn alloy and slag output masses and compositions for a given set of feeds. 440 MWh per operating day is used as the basis of energy input. The paper describes the key model components, assumptions made and calculation approach. Added to the mass and energy balance is a cost and revenue balance, which allows prediction of the economic performance for each simulation. Substantial use of the model has been made in simulating the performance of the current Assmang HCFeMn furnaces for both smelter investigations and future production planning. The model has also been a valuable tool in the strategic analysis of the use of future Mn ores and has formed the vital link between mine ore grades (metal and slag elements) and the expected alloy output, grade and profitability. Additionally, the model has been used in benchmarking exercises to predict other Mn smelting operations with remarkable accuracy. The paper highlights some aspects of the approaches taken in using the model to benchmark Assmang?s own furnace performance and cost competitiveness with other producers. For Assmang the development and application of this modelling technology has led to transformation in understanding of the Assmang HCFeMn furnace operations and increased awareness of the potential of its Mn ore bodies.

Jan 1, 2004

By M. Steyn

[Zr(C9H6NO)4]?(HCON(CH3)2)?(H2O), where (C9H6NO) = 8-hydroxy quinoline (oxH), was synthesized and characterized. This tetrakis-coordinated zirconium complex crystallized in the triclinic crystal system (Pi, Z=2) along with water and N,N?-dimethylformamide(DMF) solvate in the asymmetric unit. The metal atom is surrounded by four N,O-donating bidentate ox-ligands that are arranged around the metal centre to give a square antiprismatic coordination polyhedron with a small distortion towards a dodecahedral geometry. Crystal packing is stabilized by intermolecular interactions of adjacent oxine ring systems in neighbouring molecules, as well as hydrogen bonding of the aqua and DMF solvate molecules, linking the molecular entities into a supramolecular three-dimensional network.

Jan 1, 2013

By S. Parada, P. T. Jones, M. Guo, S. Smets

The corrosion behaviour of a high-quality rebonded magnesia-chromite refractory in contact with a vacuum oxygen decarburization (VOD) slag with high Al2O3content (15?20 mass per cent) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterization of corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature and the Al2O3content in the slag is discussed. Keywords: corrosion, magnesia-chromite refractory, VOD slags, vacuum induction furnace

Jan 1, 2004

Rock mass classification systems are extensively used in rock engineering design work, and mine design is no exception. Among the systems most widely used for mining-related design work are the NGI 0-system (Barton et al., 1974), the RMR system (Bieniawski, 1976), the MRMR system (Laubscher and Taylor, 1976) and, more recently, the GSI system (Hoek et al., 1998). Classifying the rock mass is widely seen as being the fieldwork required to characterize the rock mass and enable the application of empirical design methods associated with the different classification systems. This paper argues that it is fundamentally important to recognize the distinction between rock mass characterization and rock mass classification. These two processes should, in most cases, be separated from each other. Rock mass characterization should be used to determine the intrinsic properties of the rock mass independently of the application; i.e. independent from the infrastructure to be designed, the size, shape, and orientation of the excavation(s) or pillar(s), etc. Rock mass characterization should also be compatible with most classification systems and empirical design methods to be used. Rock mass characterization is the background fieldwork required to perform rock mass classification and/or engineering design work. Rock mass classification is the subsequent step to the characterization, and an integral part of the design process. Parameters that vary according to the design, such as the relative orientation of geological structures compared to the opening or the mine-induced stresses, should be calculated as part of the rock mass classification and design process, rather than during the rock mass characterization process. The failure to distinguish between rock mass characterization and rock mass classification can lead to major design errors and poor results.

Jan 1, 2012

By J. M. Galera, M. D. Rodriguez, V. Pozo, S. Cooper

"Cobre Las Cruces mine extracts copper minerals from a VMS deposit located in the well-known Iberian Pyrite Belt (IPB). As an open pit, it is distinguished geologically from other IPB mines by the presence of around 150 m of Tertiary soft marls, known locally as the Guadalquivir Blue Marls, followed by a regionally important aquifer. Below the marls and aquifer the mineralization is hosted by rocks typical of the Palaeozoic within the IPB, comprising gossan, tuffs, slates, and sulphides.This combination of a substantially soft rock and more competent, older (but still occasionally problematic) Palaeozoic lithologies constitutes a unique geological framework and presents substantial challenges in maintenance of slope stability, and therefore operational safety, at the mine site. This paper describes the fundamental design, excavation, and monitoring measures implemented at the mine to maintain safe production, and the lessons learnt during the mine development. IntroductionAs a modern Spanish mine, Las Cruces is committed to the use of best available technology and practices with the aim of guaranteeing the production of ore in a safe environment. From a practical perspective, this implies the realization of a high quality pit design, ongoing geotechnical mapping of exposed slopes to ensure conformity with design, and use of leading geotechnical surveillance technology to complement visual observations. The focus of this article is to illustrate how, at a mine site with potentially problematic soil/rock conditions, multiple advanced techniques employed from design stage analysis through to final pit configuration and vigilance, were combined to achieve an overall control of the ground conditions. In Figure 1 the layout of the pit is shown, illustrating development at the beginning of 2015."

Jul 1, 2019

By R. Flatabø, K-E. Johansen, L. Hunsbedt, P. M. Cowx, J. A. Bustnes

Eramet and Tinfos are two producers of manganese alloys in Norway, which have worked hard for several decades to improve both the internal and external environment. Furnaces producing ferro- and silico- manganese alloys generate large amounts of off-gas that contains substantial amounts of dust, heavy metals and organic by-products. The dust is separated from the gas in venturi scrubbers by washing with water. The water is cleaned and recirculated, and the surplus water coming from moisture in the raw materials, is discharged to the adjacent fjords after further treatment. Emission figures show that the discharge of suspended solids, manganese, zinc and PAH (polycyclic aromatic hydrocarbons) have been reduced substantially over the last three decades as a result of process improvements and installation of state of the art environmental control measures. The two plants were the first world wide to install mercury cleaning of the off-gases from the furnaces. Mercury emission reduction has exceeded 90%. Concerning other environmental issues, such as utilisation of off-gases for energy recovery and chemical purposes, both plants have achieved good results. Major effort in the environmental work has come from the plants themselves, but other players like FFF, The Norwegian Ferroalloy Producers Research Association, and SFT, The Norwegian Pollution Control Authority, have contributed to the achieved results.

Jan 1, 2007

By L. F. Contreras

In open pit mine design, it is customary for geotechnical engineers to define the appropriate slope design angles within practical limits. The conventional approach to slope angle design is based on the comparison of calculated stability indicators, such as the factor of safety (FS) and the probability of failure (PF), with generic acceptability criteria not directly related to the impacts of failure. A major drawback of this type of approach is related to the difficulty of defining meaningful acceptability criteria. An alternative methodology of pit slope design is proposed, where the economic impacts of potential slope failures are calculated and used as the elements on which to apply the acceptability criteria for design. The methodology is based on the construction of a graph, referred to as a risk map, that relates the probability of exceeding the economic impact of slope failure to the magnitude of the impact measured in monetary terms. The process includes the analysis of a selected number of representative years of the mine plan and slope sections of the pit areas to define the required inputs for the construction of the risk map. The paper discusses the concepts used in interpreting the probability of slope failure, and describes the approach followed for the estimation of the economic impacts of slope failure and the construction of the risk map. Finally, the two main uses of the risk map are discussed, including the comparison with acceptability criteria for the evaluation of a specific open pit design and the comparative analysis of open pit design options in terms of value and risk to identify optimum pit layouts.

Jan 1, 2015

By S. J. Lötter

Analysis of the major and minor components of raw zircon as well as plasma-dissociated zircon was undertaken using inductively coupled plasma optical emission spectroscopy (ICP-OES). Microwave-assisted acid extraction as well as flux fusion using lithium tetraborate were investigated as digestion methods. Microwave-assisted acid extraction samples were analysed with matrix-matched standards. The most successful microwave-assisted acid extractions yielded 44.3(1), 49.75(7), 78.3(3) and 90.0(7) per cent recovery for Zr, Hf, Al, and Fe respectively using sulphuric acid. In no instance was acid extraction capable of complete digestion of the sample matrix. A standard addition method was applied to the flux-fusion samples due to the high complexity of the sample matrix. Method validation for the flux fusion procedure was performed using the SARM 62 certified reference material (CRM) with acceptable recovery ranges being based on the 95 per cent confidence intervals of the CRM. Successful analyses were achieved for Zr, Hf, and Ti with apparent content of 66(6), 1.7(1) and 0.15(1) per cent respectively.

Jan 1, 2012