Search Documents

By R. G. Cawthorn

The vertical distribution of platinum-group elements (PGE) in the Merensky and UG2 chromitite Reefs is highly variable, but does follow certain general patterns that allow the testing of geological models. In the Merensky reef, historically popular geological representations and interpretations have suggested that the mineralization occurs in a pegmatitic pyroxenite bounded by two chromitite layers. However, there are now enough published exceptions to this relationship to expose its fallacy. The vertical distribution of the PGE depends largely upon the separation between these two chromitite layers or the absence of one chromitite layer. Where separation is small or only one chromitite layer is present, there is considerable PGE mineralization in the footwall below the pyroxenite and lower chromitite layer. With increasing separation between the two chromitites, the mineral¬ization occurs progressively higher in the succession, and tends to track the upper chromitite layer. The view presented here is that the entire Merensky package is comprised of three events of magma emplacement, in which each has produced variable reaction with, and erosion of, the footwall, causing recrystallization of pyroxenite into pegmatitic pyroxenite. The magma then produced a chromitite layer followed by pyroxenite. Each chromitite layer is associated with some mineralization, which was extensively complemented by the subsequent formation of a sulphide liquid carrying PGE that trickled down through about 1 m of permeable crystal pile. The sulphide liquid formed after, not coincident with, the pyroxenite layers. The distribution of PGE in the UG2 chromitite shows up to three upward depletion sequences of PGE, also suggesting three events. The PGE are associated only with the chromite. The contribution from a sulphide liquid is considered to have been minimal for two reasons. Cu and Ni are extremely low in the UG2 which would not be expected if sulphides had been present. Also, by analogy with the Merensky, downward trickling of sulphides would have caused some PGE to be present in the footwall. There are some PGE in the footwall, but only where remnants of chromitite occur, and the hanging wall is lacking in PGE. In the northeastern Bushveld the UG2 chromitite is thinner than elsewhere, and there is a UG3 chromitite layer, not present elsewhere, that has a high Pt/Pd ratio. It is surmized that in the rest of the Bushveld the UG3 only appears to be absent because it has merged with the UG2 to produce the high Pt concentration at the top of the composite UG2. The non-accumulation of the package of pyroxenite-norite-anorthosite between the UG2 and UG3 in the northeastern Bushveld, which is not seen elsewhere, creates an interesting challenge to the formation of silicate layering in the complex. The mineralization in the Platreef is not addressed here. Keywords Bushveld complex, Merensky Reef, UG2 chromitite, geological evolution.

Jan 1, 2011

By K. S. Liddell

The Kell Process has been developed for the extraction of platinum group metals (PGMs) and base metals from sulphide flotation concentrates. The process has been successfully tested on several different sulphide flotation concentrates, including those from the UG2 chromitite horizon and the Platreef mafic/ultramafic layer. It has been shown to provide high (>95 per cent) and selective extraction efficiencies for the key valuable metals, i.e. Pt, Pd, Rh, Au, Ni, Co, and Cu. The Kell Process consists of several commercially proven unit operations. S, Ni, Co, and Cu are first selectively removed by use of a pressure oxidation step during which the dissolution of PGMs is minimized. The residue from pressure oxidation is subjected to a thermal treatment to ensure efficient PGM recovery by subsequent chlorination. All the core steps are very similar to well-proven conventional unit operations in common use, as are the subsequent metal recovery steps to provide marketable end products. Typical metallurgical responses of flotation concentrates from UG2 and Platreef to the Kell Process are provided, and key outcomes of an energy comparison study with smelting are summarized in this paper. Kell presents a potentially substantial improvement in PGM concentrate processing technology, in terms of economics via much-reduced power costs, ease of processing, and various environmental benefits. It allows for the treatment of high-chromium low-grade 'dirty' concentrates, such as secondary concentrates from the platinum industry's 'mill-float-mill-float' (MF2) flotation circuits and concentrates from retreatment of tailings. It allows greater concentrate mass pulls, has higher tolerance to gangue intergrowths in concentrates, and its use can provide substantial increases in overall PGM recovery. Its adoption would be a step change in the platinum industry, and given the commercially proven unit operations embodied in the Kell Process, at much-reduced risk compared with other more experimental technologies. Since the initial process development work, significant improvements and refinements have been introduced as a result of further compre¬hensive testing and process modelling. Pilot-scale testing and engineering study work is in progress for several selected sites.

Jan 1, 2012

By J. P. Josien, J. F. Noirel, F. Lahaie, P. Bigarre, M. Al Heib

ABSTRACT: In June 2001, a fatal rockburst affected a longwall face in the Houillères du Bassin de Lorraine (HBL), France. Subsequently, a large operation of in situ stress measurements by overcoring was carried out with two main objectives: providing input data for the back analysis of the dynamic event and characterising the stress field in the next panels to be mined for identifying other potential high-risk zones. This paper makes a synthesis of the results of the overcoring tests performed and discusses those results in connection with the mining context, numerical model predictions, laboratory rock test results and microseismic activity. KEY WORDS: Mine, rockburst, stress, overcoring, measurement. ZUSAMMENFASSUNG: Im Juni 2001 hat ein Bergschlag eine Kohlengrube des Houillères du Bassin de Lorraine (HBL, Lothringen, Frankreich) schwer beschädigt. Nach diesem Unfall sind Spannungsmessugen durch Überborung durchegeführt worden, mit zwei Hauptziele : 1/ Daten zu liefern für die Retro-analyse des dynamischen Gebirgsschlag und 2/ die Spannungen in den zukünftigen Ausbauen so gut wie möglich zu charakterisieren, um eventuele andere Risikozonen festzustellen. Dieser Artikel stellt eine Synthese der erzielten Ergebnisse vor. Er diskutiert diese Ergebnisse in Verbindung mit dem gesamten Kohlengruben Zusammenhang, mit den Ergebnissen von numerischen Modellierungen, mit der Labor-Charakterisierung und mit der microsismische Überwachung. SCHLÜSSEL-WÖRTER: Kohlengruben, Bergschlag, Spannung, Überborung, Messung. RESUME: En Juin 2001, un coup de terrain a gravement affecté une longue taille aux Houillères du Bassin de Lorraine (HBL) en France. A la suite de cet accident, une importante campagne de mesures de contraintes par surcarottage a été réalisée, avec deux objectifs majeurs : fournir des données d’entrée permettant la rétroanalyse du phénomène dynamique et caractériser au mieux le champ de contraintes dans les futurs panneaux exploités afin de détecter d’éventuelles autres zones à risque. Cet article présente une synthèse des résultats obtenus, et discute ces résultats en liaison avec le contexte d’exploitation, les résultats de modélisation numérique, de caractérisation en laboratoire et de surveillance microsismique. MOTS CLES: Mine, coup de terrain, contrainte, surcarottage, mesure.

Jan 1, 2003

By D. Hoffmann, S. Plumb

IRUP is an iron-rich ultramafic pegmatite rock that formed due to hot ironrich fluids and gases replacing local stratigraphic zones of the Bushveld Complex. This study focuses on the estimation of the probability of IRUP occurrence on the Merensky Reef at the Marikana Karee Mine. A 2.15 million centare IRUP-rich domain at the Karee Mine was initially defined from the interpretation of a surface aeromagnetic anomaly, and exposures in the mine workings. Surface boreholes (spaced 250-500 m apart) within this IRUP domain contain approximately equal numbers of IRUP-replaced and IRUP-free intersections. Owing to the uncertainty in the continuity of the IRUP alteration (a result of the wide borehole spacing), the risk associated with the development of mining infrastructure within this domain is unquantifiable. Semi-quantitative data comprising visual estimates of IRUP replacement from reef development mapping data and surface borehole reef intersections was interpolated into blocks using indicator kriging estimation. Comparative analyses of the estimate of IRUP occurrences were made by changing the block size and declustering the data systematically. Reconciliations of the probability of IRUP predicted from the block models derived from the different data-sets and sequential indicator simulation models were analysed for four mining study blocks. A quantitative approach to modelling the occurrence of IRUP can be an additional tool for refining the estimate of the geological losses that inform the mine plan in such high-risk zones.

Jan 1, 2015

By D. J. Adams, W. K. Rymon-Lipinski

Rock engineering plays a crucial role in contributing to sustainable development in South African mining. A framework for this has been created through legislation and structures to encourage the mining industry to have a long and prosperous future. However, rock engineering input is an essential element to achieving success. The most accessible deposits have been mined in South Africa and although large reserves still remain, many of these are difficult to access and will require excellent rock engineering knowledge and skill in the future. This is borne out by the fact that more than 50 % of fatal accidents are related to rock engineering issues. Many of these may be addressed with rock engineering solutions which are not beyond current rock engineering technology. A reduction in fatalities and injuries contributes to a sustainable mining industry.

Jan 1, 2003

By S. Asokan, CVGK Murty, R. Upadhyay

The principal mineral sources of titanium are rutile, anatase (both TiO2), ilmenite (FeTiO3) and leucoxene (a weathered ilmenite of variable concentration of TiO2 but similar to pseudorutile Fe2Ti3O9). These titaniferous minerals along with their value added products like Synthetic Rutile and TiO2 slag constitute ?Titanium Feed-stocks? for TiO2 pigment, Ti metal and welding electrodes industries. Unlike in other industries, the demand driver for titanium minerals is not the metal, but the TiO2 pigment ?a specialty chemical. Of the total titanium feedstocks usage in the world, about 93 % is consumed in TiO2pigment, with only about 3 % is utilized in metal production. India?s heavy mineral sands resources are among the largest and also one of the richest grades in the world. The country?s Ilmenite resource base stands at 348 million tonnes of Ilmenite (18% of the total world reserves)along with 18 million tonnes of Rutile, 21 million tonnes of Zircon, 8 million tonnes of Monazite, 107 million tonnes of Garnet and 107 million tonnes of Sillimanite. Though the grades (Total Heavy Minerals (THM) present in the sand) of Indian deposits are relatively rich, the contained ilmenite are termed as sulphate grade with 50-53% TiO2 (Chavra deposit of Kerala and Ratangiri deposit of Maharastra are an exception with 60% of TiO2). While superior grades with adequate reserves lead to a cost advantage in ilmenite production, the lower TiO2 percentage allows the direct use of Indian ilmenite only in the production of TiO2 pigment through sulphate route and for the chloride pigment production; such ilmenite is required to be upgraded either to Synthetic Rutile (SR) or TiO2 slag. However, in order to produce TiO2 slag in India at a globally competitive cost, the issues like high power tariff, inadequate infrastructure, expensive logistics, less enthusiastic market preferences, supply-demand gaps are to be adequately addressed. This paper deals with some of the above issues and possible solutions thereto in production of TiO2 slag from Indian ilmenite.

Jan 1, 2007

By M. van Schoor

Coal remains South Africa?s most abundant and cheapest source of energy, and there is an ever-increasing necessity for optimal and safe extraction of the remaining reserves. Increasing focus on cost-effective mining and zero harm to the environment and miners has resulted in a shift in attitude towards the application of geophysics in local coal mining and exploration. Furthermore, technological advances have contributed to geophysics being embraced more readily by the coal mining industry, compared to a decade or two ago. Predictably, the growing interest in geophysical technologies has also created a need for education and training in the basic principles and application of geophysical methods, as local coal mining companies generally do not have in-house geophysicists. Consequently, the Coaltech Research Organisation?s Geology and Geophysics working group forum compiled a textbook aimed at addressing this need: to produce a guide for applying geophysics to coal mining problems in South Africa. The target audience for such a book would be coal geologists, mine surveyors, mine planners, and other mining staff with limited or no geophysics background. This paper provides a very brief overview of the book by summarizing key sections and selected examples. In doing so, the value of geophysics to solving a range of coal mining and exploration problems is highlighted.

Jan 1, 2014

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and the introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-techno-logical cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By R. Ribacchi, P. Tommasi, C. Consorti, P. Campedel

The runout of dry blocky rock avalanches produced by planar rockslides affecting a limestone formation with clayey interbeds is analysed by means of distinct element modelling. Numerical analyses are validated by means of the back analysis of a historical rockslide occurred in the investigated area and physical aspects of the phenomenon evidenced by modelling are discussed. On analyse par la méthode aux élements distincts la distance de parcours des avalanches rocheuses sèches produites par des glissements plan interessant une formation de calcaire à intercalaires argilleux. Les analyses numeriques sont validées à l’aide de la back-analysis d’un glissement historique survenue dans le site en examen. On décrit les aspects physiques su phénomène mis en évidence par la modélisation efféctuée. In diesem Beitrag wird die Reichweite von Steinlawinen besthend aus trockenem blockhaftem Fels mittels der Distinct Element Methode untersucht. Die Steinlawinen werden erzeugt von Rutschungen in einer Kalkstein-Formation mit tonhaltige Schichten betreffen. Die numerischen Berechnungen wurden anhand einer Simulation einer historischen Bergsturzen verifiziert, der sich auf den untersuchten Gebiet ereignete. Auf der Basis der erhaltenen Ergebnisse wurden die physikalischen Aspekte der untersuchten Steinlawinen analysiert.

Jan 1, 2003

By G. Denton, P. den Hoed, A. Luckos

The potential application of fluidized beds in several sectors of the ferroalloy industry is promising. They can be used in the direct reduction of iron ores to produce a feed for steelmaking, in the reduction of manganese dioxide to produce a lesser oxide for feeding to smelters, in the preheating of chromite for the production of ferrochrome, and in the calcining and pre-reduction of nickel laterites for the production of ferronickel. This paper discusses the potential of fluidized beds in theses processes and highlights the advantages of the technology over other technologies, such as rotary kilns. Two primary advantages?(1) that fluidized beds can treat fine materials and (2) that fluidized beds can be integrated with smelters in a way that allows for more efficient use of energy?may well see the technology gain prominence as more deposits of lower grade are mined and industries strive to use their resources more efficiently. In discussing the potential of the technology in the ferroalloy industry, this paper focuses on the application of fluidized beds in the smelting of chromite, nickel laterites, and manganese ores. Central to the successful operation of this technology is a knowledge of how particle properties influence the behaviour and design of fluidized beds.

Jan 1, 2007

By N. R. Shoko, J. Chirasha

Zimbabwe Alloys has been producing Low Carbon Ferrochrome since 1953. A number of operational and technical advances have been made since then. Some of these advances improved production significantly. Process control, however, remained a challenge not only in the production process itself but also in the handling of finished product. In addition the handling of the slag created an environmental problem. Process control issues were addressed by Zimbabwe Alloys Limited and Japan Metal & Chemicals (JMC) entering into a Technical Transfer Agreement. The aim of the technical transfer was to improve production, alloy quality and, thereby, the financial performance of Zimbabwe Alloys. In addition, the Low Carbon Ferrochrome production process was made environmentally friendlier by modifying the final slag handling methodology. The aspects that are covered and discussed in this paper are, ladle refractory lining changes, improved control of the process, changes in the alloy casting methodology and granulation of the final slag. The improved control of the process was enhanced by the conversion from ladle duplexing to argon purging, introduction of on-line sampling and introduction of second stage process. The combined effect of the above was a significant improvement on on-grade material production, production efficiencies, unit cost of production and a cleaner working environment.

Jan 1, 2004

By C. Musingwini

The Bushveld Complex is economically significant and strategically important to South Africa, thus it is imperative that optimal extraction of platinum group metal (PGM) resources on the Bushveld Complex is achieved. Optimal extraction broadly requires that the maximum amount of ore is extracted by excavating and hauling the minimum amount of waste in the shortest possible time, at the least cost, and in the safest and most environmentally acceptable manner. In open-pit mine planning this entails among other things, minimizing the waste stripping ratio, whereas in underground mine planning it includes minimizing the metres of waste development. In conventional mining, the main development that is in waste or partly in waste and defines the mining grid pattern includes levels and raises. It was prudent to consider optimizing level and raise spacing in conventional mining because the method is a prevalent mining method on the Bushveld Complex accounting for nearly 70% of platinum production.

Jan 1, 2010

By N. Anacleto, S. Ganguly

Reduction of Groote Eylandt (Australia) and Wessels (South Africa) manganese ores using CH4-H2-Ar gas mixture was investigated in a fixed bed laboratory reactor in the temperature range 1000?1200oC. The extent and kinetics of manganese ore reduction as a function of gas composition and temperature were determined by on-line off-gas analysis using mass-spectrometer and dew point sensor. Morphology of ores and its change in the course of reduction was examined by optical and scanning electron microscopy. Phases of raw materials and reduced samples were analysed by XRD and EPMA. Manganese oxides were reduced to carbide Mn7C3. High extent and rate of reduction by methane-containing gas in comparison with carbothermal reduction were attributed to high carbon activity in the reducing gas, which was in the range 15 - 50 (relative to graphite). The reduction rate of Wessels manganese ore increased with increasing temperature. Reduction rate and extent of Groote Eylandt manganese ore achieved maximum at 1050oC. The decrease in rate and extent of reduction of Groote Eylandt ore at higher temperatures, particularly at 1150-1200oC, was due to sintering and formation of semi-liquid silicate slag. The optimum conditions for the reduction of manganese ores were established as follows: a) temperature: 1150-1200oC for Wessels and 1050-1100oC for Groote Eylandt ores, b) methane concentration: 10-15 vol%, c) hydrogen concentration: above 30 vol%, (d) size: 1-3 mm. An addition of lime (10-15 wt% CaO) to the Groote Eylandt manganese ore increased melting temperature of slag and significantly increased the rate and extent of reduction at elevated temperatures.

Jan 1, 2004

By E. Pezennec

A voluntary comprehensive environmental Risk Assessment was launched at the end of 2004 by the International Chromium Development Association. The completion is scheduled for mid 2006.EURAS, a leading environmental consultancy, was commissioned for this project, as this firm wrote in particular the Metals Environmental Risk Assessment Guidelines, the reference document for the metals and metals compounds, in particular for the forthcoming European new Chemical Policy and the Globally Harmonized System for the Classification and Labelling of Chemicals (GHS). This project follows a stepwise approach, comprising 3 distinct steps: - Initial Risk Assessment: compilation, evaluation of the existing effects and exposure data for chromium III compounds and chromium metal. This information will be used for the compilation of an initial Risk Assessment Report. - Data gap analysis: which type of additional effects data should be collected and/or which exposure scenarios merit a more detailed targeted risk assessment? Recommendations and/or suggestions for further research will be formulated. - Road map: prioritization and ranking of the different proposed research programs. The presentation will mainly focus on the results and recommendations of the initial environmental Risk Assessment from an International perspective and not from an European point of view. - Hazard assessment ? definition of the Predicted Non effect Concentration (PNEC) for each environmental compartment (water, sediment, soil) - Exposure assessment ? definition of the Predicted Environmental Concentrations (PEC) for each environ-mental compartment - Comparison of the local PEC with PNEC for the chromium III compounds and chromium metal EU industry sectors covered in the project: mining of chromite, metallurgical production of chromium metal, chromium containing alloys production, production of trivalent chromium chemicals and the main applications (pigments, leather tanning, etc..). The current status on the environmental Classification and Ranking for chromium III compounds, Chromium metal and its alloys in the GHS will also be covered.

Jan 1, 2007

By W. C. A. van Niekerk, M. H. Fourie

The carcinogenic potential of chromium (VI) has been the subject of numerous environmental and occupational studies, from which many regulatory efforts emanated. Besides the regulation of levels of known toxic substances (e.g. Cr (VI)), the classification of dusts for regulatory purposes has thus far depended on broad definitions of particle size, mainly used to distinguish only between inhalable and respirable particles. In the past, ultrafine particles (less than 0.1 µm diameter) (PM0.1) were often regarded as a non-issue, because it was believed that significant doses would not deposit in the lungs. A growing body of scientific data is indicating that ultrafine particles are more toxic than their coarse counterparts. Increased toxicity can be related to the unique dosimetric aspects of the deposition and disposition of inhaled ultrafine particles. Secondly, ultrafine particles have a larger surface area per given mass. The increased surface area can act as a carrier for co-pollutants, specifically transition metals (including chromium) that could form a coat on the particle surfaces during particle formation. This suggests that the presence of ?inert? ultrafine particles in the environment may enhance the potential for exposure to reactive airborne compounds, including Cr (VI). These factors are particularly important when information on occupational epidemiology is interpreted. It is desirable to consider the particle size distribution, for example when occupational exposure to hexavalent chromium compounds is assessed. Since ultrafine particles are more toxic than coarse particles with the same chemical composition, it could be speculated that cancer slope factors might be related to particle size distribution. This is relevant not only to carcinogenic chromium compounds, but also basically for any particle-associated toxicants. In general, the probability of developing health effects associated with occupational toxicants is likely to be higher when these are associated with the ultrafine particle range.

Jan 1, 2004

By Mark Coleman

Pnuematic Conveying and Process Injection Technologies have been implimented in the metals markets for the last 40 years and have consideribly improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider, which has turned its attention to supporting the Metals Market. Clyde seek to utilises its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries. With over 30 years experience in the process improvement industry, Clyde Materials Handling has helped their global customer base transform the way in which they operate their processes, which has enabled them to generate sustainable economic benefit and maintain their positions as leaders in their respective markets. Operators within the metals market have developed and deployed pneumatic conveying and pneumatic injection technologies. These environmentally supportive and sustain-able solutions have been used to transport raw materials within operating facilities, from storage to silo, as well as injecting these materials directly into the heart of production processes. Operators, such as Codelco in Chile, Corus Steel in the UK, and many others across the World have seen pneumatic injection solutions transform their process and costs. To inject a consistent, pulseless and accurate flow of material to a copper concentrate bath smelter, or injecting granular or pulverized coal as a coke substitute in to a blast furnace via the Tuyeres helps to increase the operational capacity, availability and productivity and reduce the cost of the operation. This paper will discuss and highlight the ways in which pneumatic conveying and injection technologies, created by Clyde Materials Handling, and applied in partnership with the customer, have helped to improve the operational performance of the production processes of operators across the non-ferrous metals markets with specific reference to applications in the Lead and Zinc Industries. With examples from Zinc Fuming in Australia, Zinc Calcine and Powder Handling in Korea, Precision coal injection to QSL and TSL Furnaces, and metered distribution of Zinc Calcine to Reactors.

Jan 1, 2008

By E. Matinde, S. L. Msibi

"The robust nature of alumina refractory materials presents opportunities for their in-process reclaiming and re-use in non-critical applications. Virgin refractories can be substituted with different quantities of reclaimed materials without compromising the quality of the refractory products. In this study, the effect of reclaimed bauxite on andalusite-containing refractory castables for tundish applications was investigated. The recycled bauxite was formulated in different proportions to replace virgin andalusite in the castables. Standard tests were conducted to evaluate the physical, physicochemical, and thermochemical properties of the formulated products. Static corrosion tests were conducted using tundish slag in order to simulate the actual operating conditions. The results show that the standard flow behaviour, open porosity, and bulk density of samples containing up to 22 mass% reclaimed bauxite were comparable to those of the reference castable. However, high-temperature properties such as static corrosion at 1400°C and hot modulus of rupture at 1500°C indicated that there is an upper constraint to the amount of substitution. The study demonstrated direct potential savings of up to 10% when the reclaimed alumina replacement ratio was increased to 22 mass%. IntroductionAlumina-based refractories can be classified into low-alumina, containing less than 50% Al2O3, and high-alumina or bauxite, containing between 50 and 90% Al2O3. High-alumina refractories have widespread applications in high-temperature metal extraction processes due to their outstanding thermochemical and thermomechanical properties and stability (Rebouillat and Rigaud, 2002; Frulli, 2016). The typical chemical composition of refractory-grade bauxite consists of 85–90 wt.% Al2O3, 5–10 wt.% SiO2, 1–2wt.% Fe2O3, 3–4 wt.% TiO2, 0.4–0.8 wt.% CaO + MgO, and 0.20–0.8 wt.% K2O + Na2O (Nyoka et al., 2013). The thermochemical and thermomechanical properties of bauxite-based refractories rely principally on the conversion of the contained silica and alumina to the highly stable corundum (?-Al2O3) and mullite (3Al2O3· 2SiO2) phases (Rebouillat and Rigaud, 2002; Hill and Sehnke, 2006; Garbers-Craig, 2008; Frulli, 2016)."

Jun 1, 2019

By G. M. Cresswell

The 2 360 t/h two module Phola coal preparation plant represents anew era of large plant in the Witbank coalfield designed to extend its life to 2020 and beyond. The plant uses the optimum processing model for Witbank coals, receiving a feed coal size of -50 mm, wet screening it into coarse and small coal fractions 50 x12 and 12 x0.63 mm before processing them in parallel through two primary DM cyclone sections, in order to make a 27.5 MJ/kg export floats product. The sinks are processed through a common high density DM cyclone section to produce a 21.5?23 MJ/kg thermal coal middlings product. The plant design incorporates the largest size DMS equipment used to date in South African coal preparation plants, i.e. 1 150 mm large diameter pump fed DM cyclones and 4.2 m width banana screens. The fine coal is conventionally processed by spirals, whereas the raw coal slimes are filtered using automated plate and frame filter presses and added to either the middlings or discards depending on its quality. The paper describes the database, innovative design concepts, construction, and commissioning.

Jan 1, 2010

By W. Barnett

The Limpopo Metamorphic Belt is a complex geological terrane with at least three major deformational events. Tectonically juxtaposed lithology, open to isoclinal folding, crosscutting and re-activated shear zones and metamorphic gneisses and schists make pit slope design and maintenance a risky business. Venetia diamond mine?s Cut 3 is planned to reach 360 m by 2011. The difficult rockmass created problems in the original pit and a new more comprehensive slope design was necessary. Nearly 9 km of geotechnical drilling were undertaken to produce a new geological model and provide geotechnical information near the final Cut 3 face. All existing data from the pit were brought together into a database. SRK Consulting were brought into the project to audit the process and provide most of the manpower for the data analysis. Existing failures were back-analysed and the geotechnical domains identified. Analyses of only the southern domains are discussed in this paper. Geotechnical engineers can design slopes at any angle, but it is up to the managers at the mine to decide what risk they are willing to accept in a slope design. Once the issue of risk was discussed and settled in respect of the consequences of failure, each of the main geotechnical domains were analysed to produce a slope design at5% probability of failure with 15% above the first ramp. A risk assessment of the design was then undertaken to determine what risk the design placed on the equipment, personnel and the profitability of the overall mining operation. The risk assessment indicated minimal risk to the operation. One of the main assumptions of the final design is that the pit slopes will be dewatered. A project was immediately put in place to determine a groundwater model for the mine and to thereby determine the best dewatering procedure. However, it should be obvious that it is practically impossible to prevent benches from getting briefly saturated with water during storm conditions. It was therefore necessary to look specifically at supporting the crests of the ramps in the problematic southern domains to guard against the possibility of crest failure during heavy rains. The data available were re-analysed toward this objective. Spiles were recommended as the most cost-effective support system, and a probabilistic approach was used in the design. The final design has a 5% probability of failure, and the analyses indicate a strong sensitivity of the required spile spacing to the strength of the reinforcement material that will eventually be used. The pit slope parameters derived as per the discussion in this paper have just begun to be implemented at Venetia Mine.

Jan 1, 2001

By J. N. Van der Merwe

In the process of pillar extraction, pillars are seldom if ever extracted completely. The pillar remnants, or snooks, play an important role in the extraction process. At the working face, they need to be stable to provide a measure of support in the immediate area. Further back, they have to fail in a controlled manner to prevent undue load build-up on the pillars that have not yet been extracted. The stability condition at the working area is the result of interaction between the stability of the pillar and that of the roof rock. It is shown that the primary mode of roof layer failure is by bending induced tension. Direct tension can be excluded in most practical conditions, and only in exceptional cases will the first failure be in shear mode. Panel spans required to cause the first goaf to be formed, predicted using analytical considerations, are of the same order as has been observed in practice. Once the first goaf has formed, the horizontal stress is reduced and failure will occur at more frequent intervals. It is shown that bending induced tension is the most likely mode of failure in an unjointed roof layer. In roof layers with a high frequency of weak or uncemented jointing, failure can be expected to occur at spans equal to the joint spacing. In this context, failure will occur at the smallest of the spans required to induce tensile roof failure and the joint spacing. A fundamental procedure to evaluate the likely roof layer failure in a stacked beam system is developed. This can to be used to estimate the loading condition on snooks. It is shown that snooks assist in stabilizing the immediate roof beam. The sizes and positions of the snooks relative to the position of the next pillar to be stooped, control the magnitude of the contribution to stability. The further the snook is from the next pillar, and the larger it is, the greater the contribution to the stability of the immediate roof. Under the condition of loading by the immediate, continuous roof beam, the position and size of a single snook controls the load acting on it. The closer it is to the nearest solid, provided that the roof overhang extends beyond the snook, the greater the load on it. However, once the immediate roof beam fails, the loading conditions change. The snook is then loaded by the tributary area load. A procedure is developed to assess the condition of snooks for different situations. Using the fundamental considerations developed in this paper, snooks can be designed to be stable during the active mining phase in their immediate vicinity, but to fail once the next line of pillars has been extracted.

Jan 1, 2005