Search Documents

By A. Madowe

This paper discusses the mine planning process for Letseng diamond mine in the Kingdom of Lesotho, in conjunction with the various software packages used during the process. The major pillars of the long-term mine planning process at Letseng are pit optimization followed by pit design and scheduling. Letseng uses Gemcom Whittle and GEMS for pit optimization and design and Runge XPAC for scheduling. The output of the mine planning process results in the generation of published mineral reserves and provides input into the Letseng overall business plan. The process of defining the key inputs for the entire mine planning process is discussed, which covers: ? Pit optimization ? Slope design as an input ? Diamond price inputs ? Operating and capital cost inputs ? Haul road design ? Generation of pit shells ? Selection of an optimum pit shell and interim cutbacks using operational scenarios ? Sensitivity analysis on the selected optimum pit shell. ? Pit design ? Slope design criteria in the detailed design ? Split shell vs concentric pit design ? Practical mining widths to determine cutback design ? Ramp design ? Pit design process in the GEMS software package. ? Detailed scheduling ? Development of scheduling scenarios in the XPAC software package ? Planning through mining production bottlenecks. ? Company-level NPV model ? Comparing scenarios and input of the different schedule scenarios into the company NPV model. Keywords pit optimisation, mine planning, pit shell, recovery, dilution, revenue factor, pit design, split shell, sensitivity analysis, scheduling, production bottleneck, NPV, discounted cashflow.

Jul 1, 2013

By Sönke Schmachtel

Several possible physico-chemical properties of composite electrodes for oxygen evolution are presented to describe experimental data for which a mathematical model had been developed. On this basis, local electrical and electrochemical properties of a composite electrode were investigated with conductive atomic force microscopy (CAFM) and scanning electrochemical microscopy (SECM). It could be shown by CAFM measurement that the boundary between matrix and catalyst particles seemed to have special advantageous electrical properties. The SECM measurements showed the presence of mass transport phenomena with increased surface concentrations, whilst the thickness of the Nernst diffusion layer was very small. An intermediate was detected and assigned to be hydrogen peroxide. From all species involved in the oxygen evolution reaction (H2O2, H+ and O2), it was concluded that local active spots exist on the electrode on which hydrogen peroxide reacts to oxygen and protons. A two?step two-material process was suggested to explain the whole oxygen evolution mechanism.

Jan 1, 2008

By L. A. Cornish, R. Süss, M. Sephton, N. B. Maledi, J. H. Potgieter, L. Chown

The gas turbine industry is faced with a challenge to improve the performance of engines, while simultaneously adhering to stringent environmental legislation. One way of addressing the problem is by further increasing the recipient working temperatures. Unfortunately, the use of nickel based superalloys (NBSAs) in the gas turbine industry has reached its limitations. Although coatings can be used for small increases, and air cooling is also incorporated by design, attention is towards developing stronger metallurgical materials having higher melting points, with acceptable creep and corrosion resistance. A series of ternary and quaternary Platinum-based superalloys were developed. Platinum was selected because of its higher melting points compared to nickel, similar fcc structure and better corrosion properties. Mechanical characterisation studies of Platinum-based superalloys alloys, which included oxidation, creep and hardness, demonstrated reasonable results, outperforming an oxide dispersed strengthening (ODS) Fe-based superalloy (PM2000) and a nickel based superalloy (MAR-M200). During any materials development where high temperatures are concerned, high strength is the primary property of interest. However, during the development of gas turbines, component life and reliability, which are influenced by temperature, need to be taken into consideration, and therefore creep as well as corrosion (both temperature dependant properties), are important. These properties become significant with increasing temperatures. With increasing demand for higher temperatures, it is becoming increasingly important to include hot corrosion properties of the alloy during the material selection process. A short description on hot corrosion and its degradation mechanisms are given in this paper. Coatings are currently dominating as the best practical solution to address temperature increases. This paper looks at benefits and shortcomings of coatings over Pt-based superalloys as candidates for applications under extreme conditions. Key words: Hot corrosion, Pt-based superalloys, Ni-based superalloys, Coatings

Jan 1, 2006

By L. Woollacott, R. P. King

This paper presents data collected from full-scale plants in order to verify the predictions of a new simulator of CIP or CL operations. Good agreement was found between the experimental data and the simulator predictions. The simulator is able to predict the effects of many of the complex operating phenomena in GIP and CL plants that previous simulation techniques could not describe. This is illustrated by predictions of how factors, such as the manner of carbon transfer, concurrent leaching, and gold loading on eluted carbon, can affect the performance of an adsorption plant.

Jan 1, 1990

By W. C. Joughin

A risk evaluation model has been developed that enables the quantification of expected injuries and economic losses resulting from rockfalls associated with a support system in a given geotechnical environment, which is described in Part I (Joughin et al., 2011b). Part II presents the validation of the risk evaluation model. Underground mapping of joints and rockfalls was carried out to provide data for field calibration of the model. This survey was limited to small rockfalls, due to the relatively short period of mapping. Therefore the model was also correlated with rockfall and rockfall injury data collected by mine personnel. The analyses showed that the model provides a reasonable estimate of the expected frequency and size of rockfalls and the frequency of rockfall injuries, but further work is required to enhance the model. Three case studies are presented, which show the benefits of improved support systems from both economic and safety perspectives. This work has demonstrated that the risk evaluation model and the software developed are immediately useful, but further work is required to develop and improve the tools.

Jan 1, 2012

By K. Bryan, O&apos

A 10-year program to integrate crushing and screening models into daily flowsheet design practice has proven successful. A Circuit Analysis Program (CAP) is used worldwide to design and evaluate new and existing crushing flowsheets. To gain user acceptance of CAP and maximize effectiveness, model development, simulation flexibility, ease of use, and developing international access are key issues. These issues have been resolved effectively resulting in flowsheet simulations to assist in justifying increased capital investment. CAP is presently utilized in Canada, United States, and South Africa with intentions to expand to Europe and Asia.

Jan 1, 1987

Guide Io Ihe Preparailon Of Papers For Publication In The Journal Of The South African Institute Of Mining And Metallurgy The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by the Council.

Jan 1, 1975

By S. M. Rupprecht

"Artisanal mining is basic mining characterized by manually intensive work methods utilizing primitive or simple equipment and conducted by individuals or small groups exploiting deposits. Artisanal mining in Rwanda and Burundi is further complicated in that the techniques applied are often inadequate, resulting in low productivity and poor recoveries, and workers are paid low wages with owners reluctant to reinvest in the mining operations. A consequence of this vicious circle is often poor working conditions, with miners operating under unsafe and/or unhealthy working conditions. An additional problem is that mining is conducted in a manner that is detrimental to the environment.Artisanal mining is commonly more dangerous than large-scale modern mining operations. Artisanal operations are generally subsistence activities with the miners focusing more on immediate concerns than the long-term consequences of their activities. When miners have no other source of income, they will usually find ways to evade controls and carry on working. Machinery tends to be expensive and often far beyond the reach of most artisanal miners, and therefore there is a general tendency for workers to focus on labour intensive and riskier mining methods.This paper proposes the introduction of small-scale mechanization with labour-intensive manual mining utilizing a bench mining approach in artisanal mines operating in Central Africa. From the 1950s to the 1980s bench mining was successfully conducted in Burundi utilizing manual labour. In order to achieve a balance between job creation and project economics, the combination of manual and mechanized mining is proposed. Manual mining offers the benefit of local job creation while ensuring good mining techniques, such as minimizing mining loses and dilution. Through the introduction of mechanized loading and hauling activities, areas of high stripping ratios can be viably mined, thus increasing the amount of resources that can be exploited. The use of a loader and tractor-trailer arrangement is proposed, thereby improving throughput, productivity, and worker safety and, reducing the impact on the environment."

Jan 1, 2017

By P. S. Pashkovsky

Theoretical and experimental investigations of the process of self-heating the coal accumulation with use of geological and mining conditions of development of the seams, as well of mass recoil parameters, factors of oxygen diffusion in coals, critical temperatures of self-ignition, incubation times received under laboratory conditions allowed working out the method of the local prognosis of the hazard of coal self-ignition in the course of carrying out the mining operations. New relationships of calculation of critical dimensions of the coal accumulation and of the incubation time are proposed.

Jan 1, 2003

By R. E. Phillips, L. A. Cramer, R. T. Jones

Atomaer (Pty) Ltd is a technology-driven company with interests in Western Australian nickel. Atomaer (RSA) Pty Ltd is a process technology company operating in Southern Africa. It is a subsidiary of Atomaer Holdings Pty Limited (Atomaer), which has operating companies in Australia, Africa, South America, and Europe. In addition, Atomaer has substantial shareholdings in Braemore Resources Plc, a nickel company with interests in sulphide nickel projects in Western Australia and Southern Africa listed on the Alternative Investment Market of London Stock Exchange (AIM); Mintails Limited, a gold company with interests in gold operations in South Africa listed on the Australia Stock Exchange; and Brinkley Mining Plc, a uranium company with interests in Southern Africa listed on the AIM. Independence Platinum Limited (IPt) has been formed by Atomaer to undertake the commercial development and exploitation of Mintek's ConRoast technology with the strategic objective of providing independent smelting and refining facilities with lower capital and operating costs for the treatment and processing of platinum concentrates, including those with high chrome and/or nickel and/or low platinum group metal values, for the development of platinum projects by junior resource companies in South Africa. The platinum mines of South Africa have traditionally exploited the Merensky Reef of the Bushveld Complex for platinum production. However, the mining of this reef is reaching depths that require significant vertical shaft systems and costly refrigeration for access to the ore bodies at deeper levels. In the past decade, all of the platinum producers have begun to mine the UG2 reef because of its cheaper mining costs. UG2 ore usually has lower platinum group metal contents and higher chrome values. The new junior resource companies have gained access primarily to UG2 reefs. Consequently, platinum mining is becoming more UG2-based and the resulting concentrates contain high levels of chromitite. UG2 concentrates are difficult to smelt in the current six-in-line submerged arc furnaces, and this leads to increased capital and operating costs for those smelting operations. The platinum mines of South Africa produce the majority of the world's platinum metal used in automotive catalysts and jewellery. As the platinum market is forecast to grow at a healthy rate into the future, the SA producers Anglo Platinum, Impala, Lonmin, and Northam are planning to expand mining operations in the next decade. Furthermore, a number of smaller new producers who are accessing other mineral resources are entering the buoyant market and will produce platinum concentrates for purchase or toll treatment. Hence, a shortage in both smelting and refining capacities is anticipated. Further smelting and refining facilities independent of the major platinum producers will be required in South Africa by 2010. Mintek's ConRoast technology is best suited to fill the need to treat a high proportion of UG2 concentrates in a cost-effective and technically efficient manner. Atomaer base metals technology has been developed for rapid leaching of nickel and other base metals from alloy. Significant reductions in capital and operating costs are expected from the combination of the two advances in process technology compared with that installed at the existing smelters and refineries that were established over 20 years ago. Independence Platinum will be listed on AIM and the Johannesburg Stock Exchange (JSE) in 2007, and developed as an independent, vertically-integrated platinum company using its independent smelting and base metals refining facilities as a strategic platform to promote the development and mining of platinum projects by junior resource companies in South Africa through technical co-operation, strategic alliances, joint ventures, off-take, toll-refining, and marketing agreements.

Jan 1, 2006

By A. Smith

The practice of leaving barrier pillars between adjacent longwall panels at The Durban Navigation Collieries (Pty) Ltd (Dumacol) has resulted in a considerable loss of coal reserves. Dumacol has now modified the layout of its longwall panels to allow the concurrent mining of barri9f pillars and the extraction of the longwalls. The Implementation of the new panel layout has increased the percentage extraction of reserves and will result in an extension in the life of the mine. The method of extracting barrier pillars between adjacent longwall panels is described in this paper.

Jan 1, 1985

By A. D. Pienaar

The aqueous chemistry of niobium and tantalum compounds with hydrofluoric acid is a mature field of investigation. In contrast, very little attention has been paid to reactions of these compounds in non-aqueous environments. Similarly, reactions of elemental fluorine with niobium and tantalum compounds have received little more than cursory attention in literature. This work discusses the isothermal reaction kinetics derived from thermogravimetry, using a less redundant approach than is currently the standard. We also discuss the most likely kinetic models for this reaction.

Jan 1, 2012

By D. Duncanson, R. J. Davidson, C. G. S. Schmidt, G. A. Brown, J. D. Taylor, N. W. Hanf

The development of a cyanidation route for the treatment of gold-plant gravity concentrates is described. This work was carried out as a natural consequence of earlier improvements to the recovery of gold in the gravity sections of existing gold plants. Concern about the environmental aspects of the conventional amalgamation process was further motivation in the development of an alternative procedure. It was found that the partial pressure of oxygen in solution was the most critical reactionrate determining factor. The rate of gold dissolution was shown to be controlled by the reaction rate below approximately 25°C and by diffusion above that temperature. Thus, the efficiency of pulp agitation and oxygen partial pressure permitted a high degree of control over the rate of gold dissolution. The use of oxygen rather than air significantly increased the dissolution rate of both gold and silver. The solubilities of sodium, calcium, and potassium aurocyanide complexes under simulated reaction conditions were studied, and it was established that the values for the sodium and calcium complexes were limited, requiring the use of lower pulp densities and higher reaction temperatures for the treatment of very high-grade concentrates. The presence of excessive amounts of tramp iron in such concentrates of up to 25 per cent by mass was found to result in poor gold dissolution owing to the cementation of gold under certain reaction conditions. The maintenance of high oxygen partial pressures, together with high cyanide concentrations, high pH levels, and the presence of calcium in the system, all aided in passivating the tramp iron. Copper, gold, and iron were shown to be the main cyanide-consuming elements. Optimum gold dissolution was obtained in a closed bench-scale reactor incorporating a flotation-machine type of agitator for effective pulp agitation and oxygenation, the oxygen being recirculated. The reactor was designed to operate under a very small positive pressure. After reaction times of 2 to 6 hours at temperatures in the region of 30°C, both the gold and the silver dissolution averaged 99,S per cent. In the case of very high-grade concentrates, it was shown that gold could be floated in the same reactor by drawing off the flotation concentrate through a port in the reactor. A flotation recovery of 87,4 per cent of the gold in 3,9 per cent by mass was obtained. The recovery of osmiridium from cyanide-leach residues and the electrowinning of gold from the pregnant liquors were also considered as processing aspects in the treatment of gold-plant belt concentrates. Final table tailings with a gold concentration of 10to 12 gft were obtained. The results of the investigation strongly suggested that an alternative cyanidation route for the treatment of gold-plant concentrates was technically feasible, provided the system included effective agitation and oxygenation. In the case of lower-grade concentrates, cyanidation followed by the electrowinning of gold appears to be the simplest route, while, for high-grade concentrates, flotation and smelting of the concentrate followed by cyanidation of the flotation tailings are suggested. The use of oxygen rather than air for sparging the pulp would depend largely on the grade of material to be treated. A preliminary comparison of the costs related to the amalgamation and cyanidation processes for the recovery of gold from such concentrates indicated very similar capital and operating costs. It was concluded that other considerations, e.g. toxicity, safety, and lower labour requirements, were more important than such small cost differences. Furthermore, the 'opening' of the gold-plant gravity circuit, which would be made possible by a cyanidation route, would further reduce the operating costs because of the subsequent decrease in the tonnage to be treated.

Jan 1, 1978

By C. Musingwini, C. Beaumont

"Kansanshi mine, located in northwestern Zambia, uses conventional openpit mining to produce primarily copper, with gold as a by-product. The ore is extracted from a deposit with highly complex mineralogical suites that are difficult to process, sometimes leading to poor recoveries. The mine was using an ore classification system called ‘Mat-Type’, which classified various ore types into 22 different quality categories, ranging from poor to good quality. Ore with poor recovery was classified as ’poor quality’ ore and directed to long-term stockpiles. Due to a lack of proper integration between the technical and functional areas forming the mine value chain, Mat-Type unintentionally misclassified ore. A geometallurgical analysis was therefore undertaken to review Mat-Type and a new geometallurgical ore classification system, called ‘OXMAT ’, was developed to replace Mat- Type.When implemented, OXMAT eliminated nine of the 22 ore categories and the remaining 13 ore categories could now be more accurately and consistently defined, leading to a significant change in the quantity of ore being mined. OXMAT demonstrated that within a defined test volume of the geological model, waste tonnes could be reduced by 19% while ore tonnes could be increased by 17%. This paper therefore demonstrates the value created through integrated geometallurgical modelling. IntroductionKansanshi mine is located in northwestern Zambia, approximately 10 km north of the provincial capital Solwezi and about 160 km west of Nchanga mine in the Central African Copperbelt (Broughton and Hitzman, 2002). The location of Kansanshi mine relative to other major copper deposits in the Copperbelt is indicated in Figure 1.Kansanshi mine uses conventional openpit mining methods to exploit copper- and gold-bearing veins hosted in a structurallycontrolled mineral deposit. Mining is carried out in two areas of the deposit, the Northwest and Main pits. A third area of the deposit, called Southeast Dome, is currently not being exploited (Figure 2)."

Mar 1, 2019

By S. L. Miller

The development of a pilot gold geostatistical ore reserve system proved that geostatistical methods worked well for the routine production of annual ore reserves on gold mines of the Gold Fields of South Africa (GFSA) group, and that the techniques could also be practically implemented, understood and accepted by Survey Department personnel. Many side benefits of the pilot system became apparent, and a variety of useful management information was provided by manipulating the data values that were already captured. It was decided that it was a priority computing project to develop a standard production system (GORS) for routine use by all the GFSA gold mines. Experience with the pilot system enabled detailed functional specifications for GORS to be laid down. These, together with group computing policy determined the terms of reference and constraints for the GORS development. System design could not be finalized until new and appropriate mainframe database software and graphics workstation equipment and software had been found. With these in place the basic system was structured to take best ad- vantage of the interactive features of the workstation, the number-crunching power of the mainframe and the flexibility offered by a relational database and associated 4GL tools. Application sub-systems were developed for data capture, statistical applications, geostatistical calculations, contour plotting and graphical queries. GORS is being introduced to the mines in a phased manner with suitable documentation, training and support structures to enable it to be routinely and effectively used on a day-to-day basis by all group gold mines.

Jan 1, 1987

By JOURNAL SAIMM

SYMPOSIUM ON PELLETS AND GRANULES During October 1974, the Newcastle branch of the Australasian Institute of Mining and Metallurgy is to hold a symposium on pelletizing and granulation, with particular reference to the iron ore, fertilizer, and cement industries.

Jan 12, 1973

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

By C. Tokoro, T. Kato

The objective of this study is to improve the shrinking core model for particles with a particle size distribution and clarify the activation mechanism of rare earth elements dissolution by mechanochemical activation. To achieve this objective, the method, called the doubly integrated micromodel, was applied for a shrinking core model in this study. This method consists of integrating the batch leaching rate of a single particle over the distribution of both feed particle size and reactor residence time to arrive at the fraction unleached. The usefulness of the shrinking core model improved by doubly integrated micromodel was confirmed by comparing it with a shrinking core model. To apply the shrinking core model improved by doubly integrated micromodel to rare earth elements dissolution from weathered residual rare earth ores by mechanochemical activation, leaching experiments were performed for grinding samples by planetary ball milling. The reaction equation of mechanochemical reaction by planetary ball milling for weathered residual rare earth ores was investigated by x-ray absorption fine structure analysis. As a result of a kinetics study, the rate-determining process of leaching changed from reaction to diffusion reaction control by planetary ball milling. Based on these results, it was revealed that the main mechanism of activated rare earth elements dissolution from weathered residual rare earth ores was a mechanochemical reaction by planetary ball milling. Keywords: Mechanochemical reaction, particle size distribution, shrinking core model

Jan 1, 2020

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

By А. Klemyatov, T. Vologdina, U. Gordeeva, S. Zbinets, А. Kalugin, N. Rozhdestvenskiy

The plants integrated in the PhosAgro group of companies perform processes from scientific research to the project, from ore mining to shipment of fertilisers and feed additives to consumers. An extensive process chain maintains smooth interaction at all stages from research to production. As an example, the paper shows the revamp of two beneficiation plants (ANOF-2 and ANOF-3), requiring a comprehensive approach to task solving. The intention of the revamp was to increase the total yield of apatite and nepheline concentrate, taking into account the gradual decline in the quality of ore being processed and ensuring the yield stability of final products during re-equipment of the plants. At ANOF-3, the crushing and grinding cycle was modernised, the production of nepheline concentrate was implemented, and the capacity of apatite flotation, dehydration, and drying was increased. At ANOF-2 a new process chain was implemented for the production of apatite concentrate in workshops previously used for the production of nepheline concentrate. The main building was withdrawn from operation, where ore grinding, apatite flotation and apatite concentrate thickening had been carried out. The total increase in apatite concentrate yield at two beneficiation plants was 1.3 times. A further increase in concentrate production is planned. Keywords: Apatite, nepheline, fertilisers, beneficiation, flotation, column flotation machines, revamp, fine screening

Jan 1, 2020