Search Documents

By G. Akdogan, J. H. Zietsman, C. Dorfling, D. Attah-Kyei

The development of newer and improved electrical products has led to an increase in the rate at which older products are discarded as waste. The main focus of electronic waste is the printed circuit board (PCB) because of the inherently high value of contained metals such as gold and copper. Several options for treatment of the non-metallic fraction including material recycling, where the residue may be used as inclusions in concrete or asphalt materials with minimal processing or chemical recycling, where chemicals and fuels are produced from the residue using pyrolysis exist. In this paper, the utilisation of the non-metallic leached PCB waste fraction as reductant in secondary copper smelting was investigated. Analysis of the leached residue revealed that PCB is highly amorphous and has a carbon content of 28.5%, an oxygen content of 23.1%, with the ash and volatile matter contents 40.1% and 44.8% respectively. Thermodynamic simulations of secondary smelting of copper were conducted in terms of metal recovery, and the energy required when PCB was used as a reductant. The results were also compared with that of coal and PCB-coal blends. The simulations revealed that as PCB in the blend used as reductants increases, the amount of energy required for the smelting operation decreases. Metal recovery slightly decreased as the mass percent of PCB in the blend increased due to lower carbon content present in PCB relative to coal. The results also highlighted the energy saving with PCB-coal blends which was around 160 kWh per ton of feed relative to coal. The decrease in the amount of energy required for the operation is attributed to the higher volatile content of the PCB, which is also a part of the reduction process. Keywords: PCB leach residue, alternative reducing agent, secondary copper smelting

Jan 1, 2020

By J. McPherson

In order to add value to South Africa?s gold reserves AuTEK, a joint venture between Mintek and Anglogold-Ashanti, was started in 2000 with the aim of developing new industrial uses for gold. Accordingly gold catalysts are being made in kilogram quantities by Project AuTEK and sold toend users and other interested parties under the trade name AUROliteTM. Although these materials are optimized for use in CO oxidation applications, demonstration of appropriate activity, selectivity and durability in both liquid- and other gas-phase reactions has been shown1. The review below highlights the recent use of these materials, and other gold catalysts, in reactions of commercial interest.

Jan 1, 2009

By D. G. Krige

The problem of a realistic investment analysis for a new mining venture that sells its products on the international metal markets IS studied against the background factors, firstly, of different inflation rates between the countries hosting the mines and those. hosting the metal markets; and, secondly, of the changing pattern of currency exchange rates between such countries. The purchasing-power parity theory is used to establish a pattern of relationship between these two factors, and to develop a more logical approach to the long-term forecasting of metal prices in the currency of the country in which the mine is situated.

Jan 1, 1979

By F. Samimi Namin

One of the main tasks in exploitation of mines is to select a method suitable for the deposits, specific features including geometric, geo-mechanical and geological features. The purpose of selecting a mining method at this stage is to choose one or more method(s) having the most coordination with the deposit?s conditions and external factors, including the allocated budget and local technology for detailed feasibility studies. Several methods have been developed in the past to evaluate suitable mining methods for an ore deposit, based on its physical characteristics. These approaches can be classified into three groups: (1) profile and checklist methods, (2) numerical ranking (scoring) methods, and (3) decision-making models. Most of these methods have shortcomings. Considering the fact that most of the specifications of mineral deposits, such as dip and depth, are linguistic variables, absoluteness of the explaining parameters by previous methods can be mentioned as the most important disadvantage of these methods. This paper discusses the Fuzzy technique for order performance by similarity to ideal solution (Fuzzy TOPSIS) to determine the mining method. The fuzzy decision making (FDM) software tool is employed to develop a Fuzzy TOPSIS based model. Application of this model with various values (crisp, linguistic and fuzzy) of the deposit eliminated the existing disadvantages of other methods. Two empirical illustrations demonstrate the effectiveness and feasibility of the evaluation procedure. These show that the proposed model performs better than its alternatives. Keywords: mining method selection, fuzzy TOPSIS, decision making, mining engineering, linguistic variables.

Jan 1, 2008

By P. V. Scheers

A rotating-cylinder electrode (RCE) was used to simulate the effect of flow velocity on pipe corrosion. A comparison is made between the electrochemical measurements obtained and those measured with a laboratory-scale flow loop. There is good general agreement if the speed of rotation of the RCE is adjusted to give the same value of mass transfer Coefficient as in the other system. Hence, it appears that the RCE is well suited to simulate actual flow conditions in pipes. The simultaneous effect of flow velocity and pH value on the corrosion rate of mild steel in a synthetic mine water was investigated. The i1nrease of corrosion rate was found to be more pronounced at lower pH values and, apart from a sharp increase below pH 4, the initial corrosion rate also increased at pH 7 and 6.

Jan 1, 1992

By X. Zhang, Z. T. Yuan, C. Zhang, H. M. Zheng, X. M. Wang, L. X. Li, N. Li

In metal mines, comminution is commonly used to liberate minerals for subsequent mineral concentration processes, such as flotation, magnetic separation and gravity separation. However, ores are aggregates of valuable minerals and their disseminated gangue minerals, and these minerals exhibit diverse comminution behaviours. In carbonate-bearing iron ores, hematite, siderite, and quartz are the predominant minerals, of which hematite is the objective recoverable mineral. In this regard, the present study aimed to identify the imperfections in siderite minerals by X-ray computed tomography (XCT), and thus quantitatively characterise their size and shape in terms of Feret diameter and aspect ratio, as well as other parameters. XCT images indicated the protogenetic ubiquity of pores <5 μm in diameter and cracks of 7-8 μm inside siderite particles. In the ground product of artificially mixed siderite and hematite, siderite particles were smaller than hematite particles. Siderite particles had a larger surface area and greater surface roughness than hematite particles of the same volume, which was attributable to the intrinsic holes and cracks in siderite particles. This study provides an insight into the relationship between the inherent imperfections of minerals and their comminution properties. Keywords: Siderite; X-ray computed tomography; particle imperfections; grinding behaviour; sliming

Jan 1, 2020

By S. C. Maji, U. S. Chattopadyay, S. Chaudhuri, T. Gouri Charan

India is devoid of coking coal resources, which is a vital raw material for coke making. As a result it has to import about 80% coking coal for steel making. Indian National Steel Policy, 2017 has envisaged crude steel production around 300 million tonnes Mt) by the year 2030-31 and forecasts coking coal demand of 161 Mtpa (million tonnes per annum). One way of improving the indigenous resources is to study the performance of existing washeries and to improve the clean coal recovery by adopting suitable technology. A study was carried out, mainly to focus on the fine coal circuit of an existing coking coal washery, to generate the desired quality of clean coal. The operating coking coal washery being studied is presently feeding coal from nine different sources with varying feed ash contents. The coal fines varied in ash content ranging from 19.5% - 43.6%. For treating the coal fines, the washery has operated a spiral for the past few years. Performance studies were carried out, and it was found that the spiral is not efficient in recovering the cleans. Detailed investigations were carried out on the coal fines using flotation techniques, and it was found that to achieve a low ash clean coal, the froth flotation is a much better beneficiation option than a spiral, The studies showed that the recovery of clean coal through a spiral is 67.7% at ash content of 27.0%, while flotation tests showed a recovery of 68.1% at 16.5% ash content. Keywords: Coking coal washery, near gravity material, spiral washer, froth flotation

Jan 1, 2020

By P. A. Roberts

A modified in situ leaching method for extracting gold from oxidized gold ores using a non cyanide lixiviant is proposed. A non cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide bearing solutions into the subsurface. Oxidized gold ores are the initial focus because earlier research on the use of sodium thiosulphate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulphate breakdown. A reconnaissance research programme, involving ore characterization and hydrometallurgical testwork on samples from four Australian ore deposits and preliminary reactive transport modelling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulphate and ferric EDTA, and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples under anaerobic conditions. The ore characterization and reactive transport studies, suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Physical permeability enhancement could be achieved by blasting and/or hydraulic fracturing of the ore. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in place leaching? has been adopted for the proposed gold extraction system

Jan 1, 2009

By J. Petersen, S. W. Robertson

Heap leaching is used extensively for the processing of low-grade copper, gold, and uranium ores. The hydrodynamics is often the most important factor that limits the rate of metal recovery. Over the past decades the author has performed physical and hydraulic testing of a large number of ore samples considered for heap leaching. The data were reviewed to investigate the effect of physical properties such as particle size distribution (PSD) and bulk density on the hydrology. The unsaturated flow through the bed is traditionally modelled with soil science models such as Brooks-Corey (BC) and Van Genuchten-Mualem (VGM), which relate the hydraulic conductivity to the degree of saturation, also known as the hydraulic conductivity function (HCF). However, most authors found a disconnect between the saturated hydraulic conductivity (KS) and the rest of the HCF, which is explained as resulting from a transition from capillary-to gravity-controlled flow. However, the author found no such transition, and found the flow to be governed by capillary flow throughout. Traditional BC or VGM fits were found to be appropriate, however it was necessary to modify the model to include a point of inflection, above which the hydraulic conductivity remains constant while the moisture content keeps on increasing. It was proposed that this is the result of unconnected or poorly connected pores, which fill with solution but do not create additional flow channels. The point of discontinuity was also found to correspond with the air entry point, measured independently from the air conductivity curves. On average, the air entry point corresponds to the experiential rule that the void saturation should remain below 65% for aerated heaps.

Dec 11, 2024

By C. Massola, E. E. M. N. de Guzmán, M. G. Bergermana

The abrasiveness of a mineral or rock is an extremely important topic in the mining industry and is generally measured by the Bond abrasion index (AI). However, to determine such an index by the Bond test requires 1,600 g of sample with particle sizes ranging from ½” to ¾”, which are not available in certain situations, such as ore prospecting, drilling, and geometallurgical studies. In order to investigate the abrasiveness of smaller-sized sample materials, a modified LCPC test was developed, which allows testing fine materials (i.e., 1.0 mm or smaller) to predict wear in ore processing circuits and anticipate possible failures resulting from changes in abrasive characteristics of the ore being processed. The results for 16 different materials indicated a good correlation with the AI and the modified LCPC, resulting in a reliable alternative for the AI. Keywords: Bond Abrasion Index (AI), LCPC, abrasiveness

Jan 1, 2020

Colloquium and General Meeting were held at Kelvin House on 19th May, 1971, the theme being &apos;Modern trends in coal mining practice.&apos; Mr V. C. Robinson (President) was in the Chair. The Colloquium was attended by 205 delegates and was opened by the President at 9 a.m. OBITUARY The President: &apos;It is my sad duty to announce the death of C. C. Cullen, Fellow, who joined the Institute in 1946 and passed away on 15th March, 1971. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments silence&apos;. ELECTION OF SCRUTINEERS The President: &apos;In terms of Clause 9.4 of the By-Laws I now call for the nomination of seven Corporate Members to act as scrutineers of the ballot for Council&apos;. Messrs V. C. Robinson, Prof D. D. Howat, Dr J P Hugo, D. G. Maxwell, J. K. E. Douglas, R. J. Adamson and P. Lambooy were nominated by P. W. J. van Rensburg and seconded by P. A. von Wietligh. The President: &apos;Are there any further nominations? If not I declare these gentlemen elected.&apos; MEMBERSHIP The President: &apos;I have much pleasure in announcing that the names of candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Douglas Edward King, Bryan Rudolph Scott, James Gregor Phimister, Anthony David Walters. Graduates: Cornelius Johann Muller, Marthinus Stephanus Mulder. Associates: John George Everson, Colin Robert Llewellyn Davies. Students: Francois George Enslin Beetge, Ewald Boshoff, Christiaan J. Cloete, Christopher John Davies, Cameron George Elvin, Kenneth Eric Field, Johannes Louis Fourie, Hans Gert Gastrow, Peter John Ledger, James Robert William Lindsay, Kynaston Lloyd McDonald, Richard Peter Mohring, Arthur Leslie Painting, Matthias Arthur Pascall, Ian Neil Sinclair, Donald Allan James Ross-Watt. MEMBERS TRANSFERRED TO A HIGHER GRADE From Member to Fellow: Peter Norman Roberts. From Associate to Graduate: Alfred Eric WaIter Fletcher. From Student to Graduate: Wilfried Pierre de Villiers, Edward Emile Eichenberger, William Alan Nairn, Lodewyk Johannes de Jager, Colin Henry Obray, John Grenig Rees. COLLOQUIUM The President opened the proceedings and introduced Mr N. W. S. Schumann as the overall chairman for the day. The following papers and contributions were presented: FIRST SESSION: Chairman R. C. J. GOODE. Paper: &apos;Problems encountered in the operation of a new colliery&apos; by P. M. C. Wilson and A. A. Oakes. Contributors: D. J. Moloney, G. R. Canny, I. G. Evans, R. B. MacGillivray, Dr F. G. J. de Jager, M. J. Deats, and N. Zolezzi. R. B. MacGillivray Mr President and gentlemen, I would like to congratulate the authors on presenting a most interesting paper on a very important subject. After several attempts at finding suitable reserves to extend the life of Welgedacht Exploration Company&apos;s Utrecht Colliery a block of coal rights was acquired south west of the town of Utrecht. A study of these reserves showed that they would enable a satisfactory return on capital invested to be achieved. It was decided therefore to open up what is now called the Zimbutu section of Welgedacht Exploration Company, to produce 41 000 metric tons of coal per month. The decision to open this section was taken in August, 1968 and due to certain allocation requirements it was necessary to bring it into production by the 1st of January, 1970. Fortunately a fair amount of statistical data had been collected prior to August, 1968 from the old Utrecht Colliery in anticipation of opening a mine and a fairly detailed rechnical report had been prepared. As a result the dead line was only missed by four days. Main features of the Design A feasibility study was carried out on three possible shaft positions and the final position was selected from these three on economic grounds. As the coal seam at the selected shaft position was only 21 metres below the surface it was decided to sink two twin incline shafts to enable rapid establishment of through ventilation and alternative hauling arrangements for quick development. This also allowed the final vertical ventilation shaft to be placed at some distance away to avoid the nuisance of fan noise. Second outlet requirements are also very well met by these twin inclines. Again on the basis of economics and also due to the uncertainty of roof conditions it was decided to use hand loading methods underground. However, to allow for future possible conversion to mechanised loading, should this become economical through rising wages, a conveyor belt was installed in the hauling shaft. This conveyor belt is fed from an endless rope haulage in the east companion by means of tipplers, a bin and a feeder. The main development heading was left clear for the future installation of a conveyor belt which would afford easy conversion to mechanisation.

By D. Krebs, Tero Korhonen, X. Yang, A. Kirpala, N. Heino

At present, over 85% of the world’s rare earth oxides are produced from the bastnäsite ores, found mainly in China. Meanwhile, the ion adsorption ores are the most important sources for heavy rare earth production. As the demand for rare earth materials in the world increases, other forms of rare earth deposits will become new potential resources of rare earth production in the future. In this paper, flotation performance of a steenstrupine ore from the Kvanefjeld deposit for rare earth recovery was studied through laboratory bench testwork. The effects of various factors including grinding size and collector dosage on recovery and selectivity of the selected rare earth elements, La, Ce and Y, were investigated. A rare earth concentrate with the grades of La 2.8 wt%, Ce 5.1 wt% and Y 1.0 wt% at recoveries of 80.5% La, 79.8% Ce and 55.3% Y was obtained in optimum conditions. Further potential to improve the efficiency of REE flotation was discussed. Keywords: Rare earth elements, flotation, steenstrupine, Kvanefjeld deposit

Jan 1, 2020

Deciding on plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g/t of fresh feed has been assumed a reasonable starting point with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2012

By von Wielligh. L., D. G. Hattingh, M. N. James, W. Thomas

"SynopsisThe process of joining materials by friction is based on generating the heat necessary to create a solid-state mechanical bond between two faying surfaces to be joined. In simple terms, the components to be joined are subjected to frictional heating between rubbing surfaces, causing an increase in interface temperature and leading to localized softening of interface material, creating what is described as a ’third body’ plasticized layer. This plasticized zone reduces the energy input rate from frictional heating and hence prevents macroscopic melting. The plasticized layer can no longer transmit sufficient stress as it effectively behaves as a lubricant (Boldyrev and Voinov, 1980; Godet, 1984; Singer, 1998; Suery, Blandin, and Dendievel, 1994). The potential for this solid-state frictional joining process to create high-performance joints between, for example, dissimilar materials with limited detrimental metallurgical impact, and reduced defect population and residual stress level, has had a very significant impact on fabrication and repair in industrial sectors such as transport. This paper presents a brief overview of the advances made within the family of friction processing technologies that could potentially be exploited in the nuclear industry as alternative joining and repair techniques to fusion welding.Modern friction processing technologies can be placed into two main categories: those that make use of a consumable tool to achieve the intended repair or joint (friction stud and friction hydro-pillar processing) and those making use of a non-consumable tool (friction stir welding). The most mature friction joining technology is friction rotary welding, where a joint is formed between original parent materials only. A new addition in this category is linear friction welding, which opens the potential for joining complex near-net-shape geometries by friction heating. The continuous innovation in friction processing over the last 25 years has led to the development of a number of unique processes and applications, highlighting the adaptability of friction processes for specialized applications for high-value engineering components.IntroductionAssessing the potential for using alternative joining and repair techniques for specific applications in a given industrial sector is informed by an appreciation of the current size and potential growth in that sector. Power generation by nuclear fission has been out of favour over the past few years, due to several high-profile nuclear incidents, e.g. the Fukushima Daiichi nuclear disaster, as well as concerns over disposal of nuclear waste and spent fuel rods. However, due to rapid increases in the demand for electricity, coupled with many fossil-fuel fired plants reaching end-of-life, there is renewed interest in installing additional nuclear capacity."

Jan 1, 2015

By Brian W. Mackenzie

The mineral exploration environment has observable economic characteristics, the assessment of which provides guidelines for exploration planning in the mining company. The long-term survival of the mining company is directly dependent on successful exploration. Exploration planning contributes to successful exploration through the development of exploration strategies. The objective of exploration planning is to select exploration environments which will enable the mining company to realize best possible profit and corporate risk conditions. Thus, the formulation of exploration strategies is based on profit and corporate risk criteria. Strategic considerations include the selection of commodities as exploration targets, geographic concentration of exploration effort, the realization of acceptable survival conditions, and the structuring of an exploration programme to optimize the economic benefits of the exploration investment process.

Jan 1, 2014

By J. Rajala

The Kupol mill facility processed a high grade free milling gold/silver ore containing 28.2 g/t Au, 324.8 g/t Ag and approximately 0.5% pyrite during 2008 operation. Gold predominantly occurs a selectrum in the ore and silver is predominantly present in the forms of acanthite, stephanite, pyrargyrite and proustite. Mill start-up was in mid-May 2008 and the mill reached the design throughput of 3 000 tpd in October. The ore was ground to approximately 70%?53 microns. A Knelson Concentrator recovered 9.8% gold and 0.5% silver. The gravity tails reported to a cyanidation circuit that has 14 hours pretreatment and 116 hours leaching. The slurry from cyanidation was then processed by counter current decantation (CCD) thickening to wash and separate the leach residue from the pregnant leach solution. Precious metals are recovered fromthe pregnant solution using the Merrill-Crowe process. The washed CCD leach residue slurry is treated with calcium hypochlorite to destroy cyanide and then sent to the tailings impoundment. Leaching is performed with a new technology called ?CELP? (CANMET Enhanced Leach Process). The Kupol mill overall gold and silver recoveries for 2008 were 95.4% and 85.6% respectively, which were 2.8% and 7.5% higher than targets. Gold and silver extractions in the leach circuit were 94.2% and 84.5% respectively. Leach profiles indicated that gold extraction reached a plateau in the 4th tank while minor silver dissolution occurred in the 5th tank. With the CCD circuit included, total gold and silver extractions increased to 95.4% and 86.6%, respectively. Optimization of the leaching strategy made it possible to reduce sodium cyanide concentration to as low as 410 ppm without compromising precious metals extractions. Silver was effectively leached from the refractory silver minerals because CELP produced more oxidized mineral surface relative to the conventional cyanidation leached mineral surfaces. The average cyanide consumption for 2008 was 1.3 kg/t. The new leaching technology proved to be very robust and performed efficiently even with changes in feed grade and ore mineralogy. Laboratory experiments produced results that were indicative of plant performance. The robustness of the technology and the laboratory test work contributed to the success of the Kupol mill start-up.

Jan 1, 2009

By D. J. Hallbom

A new graphical method termed the ?Design Curve Diagram? (DCD) has been developed to analyse non-Newtonian pipe flow data by relating the plastic Karman number to the plastic Reynolds number. Since the plastic Karman number is directly proportional to the pressure loss gradient and the plastic Reynolds number is directly proportional to the velocity, the DCD is essentially a non-dimensional pipe flow curve. This makes the DCD conceptually easier than the commonly used Hedström-Moody diagram. While, the DCD was developed for the analysis of yield plastic fluids (e.g., Bingham plastics), it is equally applicable to Newtonian fluids.

Jan 1, 2007

By C. V. O?Keefe

Volumetric flow and mass flow are two of the critical process parameters needed to understand and control flotation processes, with others being levels, densities, and metal analyses. Both volumetric flow and density measurements can be adversely influenced by entrained air, which will result in artificially high flow readings and artificially low mass flow calculations. Array-based instrumentation has been used successfully to accurately measure both volumetric flow of aerated slurry and the quantity of air entrained within the slurry. The latter measurement has been used to correct density measurements, thus providing an accurate mass flow calculation. A case study involving the use of this technology to measure both flow rates and air entrainment levels at Eland Platinum processing facility (concentrator) will be covered in detail. In addition, with certain traditional flow meters such as electromagnetic meters, erroneous volumetric flow rates can be recorded in the presence of paramagnetic or ferromagnetic material. The use of this array technology to avoid spikes in measurements due to steel fragments passing through the pipe will also be discussed.

Jan 1, 2012

By T. Nyakudarika

The Unki Platinum Mines concentrator, employing an MF2 circuit configuration which includes fully-autogenous primary milling of run-of-mine (ROM) ore, was commissioned in November 2010. The project was Anglo American Platinum?s first PGM concentrator in Zimbabwe and would form a significant contribution to the group?s platinum production. The project financials demonstrated that the project was operating-cost sensitive. After reviewing the metallurgical testwork, mineralogical examinations, and the history of similar operations, it became apparent that the Unki ore characteristics rendered it amenable to autogenous milling. The primary ball mill, structurally designed for 30 per cent steel load, could be operated at the required initial phase throughput with fully-autogenous primary milling, realizing savings in both power requirements and grinding media consumption. The original mill sizing had been done with fully-autogenous milling in mind, but allowing for flexibility and mitigation in case of varied mining fragmentation. Since attaining steady state, target grinds have been achieved. This paper looks at the Unki ore characterization programme, design considerations, and the operational and control philosophy for a successful comminution circuit, and discusses the design to produce a flexible, low opex, mitigated comminution and overall MF2 flowsheet that is easily expanded in line with the potential for optimum exploitation of the orebody.

Jan 1, 2012

By S. Polansky, J. Kolacz

The new sorting system has been developed to achieve efficient separation at low mineral content levels. The system employs high resolution X-ray sensors providing multi-energy analysis, thus giving maximal information about processed materials measurable by X-ray radiography. It makes it possible to analyse the internal structure of the particles and directly detect inclusion of minerals and metals like copper or gold. The paper describes sorting application examples for zinc, lead, copper and gold ore with low metal content below 0.1% of Cu. The sorting system still allows high efficiency analysis, quantification and removal of rock particles representing waste fraction with no metal or a negligible amount being uneconomic to process. This brings a huge advantage during pre-concentration, where almost no losses of valuable minerals in the waste fraction can be achieved. The presented sorting system has been developed by Comex and X-MINE EU Project Consortium. Keywords: X-ray sorting, ore sorting, XRF analysis, XRT analysis

Jan 1, 2020