Search Documents

By T. Fraszczak, U. A. Peuker, T. Mütze, O. Ortlepp

Dolomite is a calcium carbonate sedimentary rock that can be found all over the world. In its calcined form it is employed for water treatment or as an additive in iron production. Calcined dolomite is produced at the Wünschendorfer Dolomitwerk GmbH in shaft furnaces (kilns). Because of an expansion of the mined deposit, significantly higher extraction costs were expected. Therefore, the existing upgrading processes for the kiln stone fraction had to be adapted and improved. This paper presents a process optimisation which allows for an increase of the yield of calcined dolomite by 10 % due to a redesign of the crusher circuit and by an additional 5 % due to a comprehensive characterisation of the kiln stone fraction itself. Here the interdependency between the pressure drop in the furnace during calcination and the size distribution of furnace stones was used to increase the amount of fine size fractions in the furnace feed without deterioration of the calcination process. Keywords: Dolomite, crushing circuits, kiln stone production, flowability, calcination

Jan 1, 2020

By H. M. Stewart, N. F. Dawson, J. P. Beukes, P. G. van Zyl, Q. P. Campbell, A. Jordaan, R. I. Glastonbury, L. N. Sadiki

"SynopsisThe physical properties of oxidative sintered pellets produced from typical South African UG2 ore are compared with the physical properties of pellets produced with conventional South African metallurgical-grade chromite ore (from the Lower Group 6 or the Middle Group 1 and 2 seams). A statistical evaluation of the cured (sintered) compressive strengths proved that pellets prepared from UG2 ore are likely to have the same, or better, compressive strength than pellets prepared from metallurgical-grade chromite ore. The cured abrasion strength of the UG2 pellets was also superior to that of the metallurgical-grade pellets. Scanning electron microscopy (SEM) backscatter, secondary electron, and elemental X-ray mapping were used to determine the reasons for the general superior strength of the UG2 pellets. The case study UG2 ore also required 13 kWh/t less energy for milling to attain the required particle size distribution prior to pelletization, which can lead to substantial cost savings. Results presented in this paper can be utilized by ferrochromium (FeCr) producers to better quantify the advantages and disadvantages associated with the use of UG2 ore for FeCr production.IntroductionChromite, a mineral of the spinel group, is the only commercially viable source of virgin chromium units. Geologically, commercial chromite deposits in the world are found in three forms, i.e. alluvial-, podiform-, and stratiform-type deposits (Murthy et al., 2011; Cramer et al., 2004). Alluvial deposits were formed by weathering of chromite-bearing rock with the subsequent release of chromite and gravity concentration by flowing water. However, these deposits are relatively small and of comparatively minor commercial interest. Podiform-type chromite deposits usually occur as irregularly shaped pods or lenses, and their distribution within a mineralized zone is usually relatively erratic and unpredictable, making the exploration of these deposits difficult and costly (Cramer et al., 2004). Stratiform-type chromite deposits occur as parallel seams in large, layered igneous rock complexes with more regular layering and lateral continuity (Cramer et al., 2004). The largest example of a stratiformtype chromite deposit is the Bushveld Complex (BC) in South Africa, which holds an estimated three-quarters of the world’s viable chromite ore resources (Cramer et al., 2004).Several chromite seams exist in the BC. The seams of economic interest are the Lower Group 6 (LG6), the Middle Group 1 and 2 (MG1 and 2), and the Upper Group 2 (UG2) seams (Cramer et al., 2004). The LG and MG seams are specifically exploited for their chromium content, while the UG2 seam is mined primarily as a source of platinum group minerals (PGMs) (Xiao and Laplante 2004). Extraction of the PGMs from the UG2 ore usually involves the liberation of the sulphide by milling and subsequent recovery of the PGM concentrate through flotation (Xiao and Laplante, 2004). Chromite in the PGM concentrate is undesirable; therefore, PGM recovery circuits are specifically designed to ensure maximum rejection of the chromite to the tailings stream. However, the chromite in the PGM tailings can potentially serve as feedstock for ferrochrome (FeCr) production, after beneficiation to increase the chromium content."

Jan 1, 2015

By M. J. Makhula, R. M. S. Falcon, S. O. Bada, L. M. Falcon

"SynopsisThe combustion and co-combustion behaviour of macadamia nut shell, high-ash coal, and anthracite, along with their blends was studied using thermogravimetry. The reactivities of all samples were analysed in air, oxygen, and CO2 atmospheres and at different heating rates from 10 to 40°C/min. Macadamia shell was found to have a lower ash content, 0.36%, than coal with 27.49% ash. The calorific values were similar, 19.64 MJ/kg and 19.44 MJ/kg respectively. The differential thermogravimetric results indicate that as the heating rates increase the ignition, peak, and burnout temperatures increase significantly, leading to high combustion rates. The interaction between the fuels was evaluated using the weighted average model, and the results indicated that there is more synergetic interaction between 20% macadamia plus 80% coal under oxygen than in air and CO2 atmospheres. The results of the investigation provide the combustion and co-combustion characteristics of various samples and their blends and indicate their combustion compatibilities. IntroductionThe global macadamia nut industry is developing at a very rapid rate. South Africa is currently the world’s third largest producer, with a production of about 35 000 t as of 2012 (Department of Agriculture, Forestry and Fisheries, 2013), compared to 840 t produced in 1996. The greatest numbers of the macadamia nut farms in South Africa can be found in Mpumalanga, Limpopo, and KwaZulu-Natal provinces, with Mpumalanga as the largest producing area. There are many factors influencing the increased demand for macadamia nuts, the most important factor perhaps being their nutritional value (California Dried Fruit and Nuts, 2011; MPC, 2014) and their suitability as a feedstock for manufacturing cosmetics, bakery products, nut paste, chocolates, sauces, and ice-cream. As a fuel, macadamia shell has a high heating value ‘as-fired’ of about 20.71 MJ/kg (Vhathvarothai et al., 2013), which could in turn be used in drying the nust, and the shell could also be milled and applied as a fertilizer."

Jan 1, 2015

Written contribution by J.F. Curtist The paper is an interesting exercise in the application of mathematics to a theoretical situation presumed to oc¬cur underground. However, some of the assumptions on which the calculations are based are unlikely to occur in any actual mining situation. Assumptions made in the paper Objections to these assumptions are noted seriatim. (1) `it is assumed that any loading-rate effect will be small and can be ignored' (p. 3). A loading rate of the order of 50 kN-12 per cent of the maximum load-is customary to prevent the props being dislodged by the blast. (2) `it is unlikely that all the props will be installed with their full stroke available, but for the purpose of this analysis, it is assumed that this is the case' (p. 3). A more reasonable assumption would be that, with the most careful selection of prop length and the most rigid control of stope width, the available stroke length would on average be reduced by the order of 70 mm on installation-20 per cent of full stroke. (3) `each support unit supports a block of 3,3 m2 bound¬ed by vertical fractures with zero cohesion that are parallel and at right-angles to the stope face respec¬tively' (p. 5). Joughin and Jager have shown this to be an unwar¬ranted assumption in respect of the positioning, the direction, and the dip of the fractures present in a stope in rockburst conditions. If, as assumed, there was `zero cohesion' between such blocks, the removal of a hydraulic prop in row 3 supporting such a block would ensure that it fell out before a profile prop could be installed in the same position. (4) `the height of each of these blocks is 3,0 m, the volume of each block is 9,9M3, the mass of each block is 27 225 kg' (p. 5). The concept of individual props being affected by dis¬crete blocks of known and uniform dimensions of relatively low ground velocities (less than or equal to 2,16 m/s) acting in line with the axis of the prop is one that lends itself to neat mathematical calcula¬tions. It does not, however, bear much similarity to the actual conditions that are exposed underground in excavations where rockbursts occur. Ortlepp and co-workers concluded that `the impulse of the shockwave can cause the displacement of the

Jan 1, 1991

By А. V. Aksenov, S. G. Rybkin, А. Y. Senchenko

For gold plants in Russia, it is very complicated and costly to use cyanide leaching for efficient processing of gold refractory ores, where gold is closely associated with sulphide minerals and the significant amount of natural carbonaceous matter present. Oxidative roasting of gold refractory concentrates is a well-known method, making it possible to obtain a high recovery rate of precious metals to a target product. The use of oxidative roasting is limited in general by the expense of capturing and neutralising the harmful components of roasted gas, mainly sulphur (SO2, SO3) and arsenic (As2O3) oxides. This paper addresses testing and development of an optimised technology to process gold refractory gravity and flotation concentrates by means of oxidative roasting which stabilises arsenic as calcium arsenate. The process involves roasting of a gravity or flotation refractory ore concentrate in a mixture with lime and calcium chloride, with a supply of oxygen, and at 600-700°С. During the roasting a carbonaceous matter of the concentrate burns out and sulphide components transform into harmless calcium sulphate (CaSO4) and calcium arsenate (Ca3(AsO4)2), and iron passes into the form of hematite (Fe2O3). After disintegration, the roasting cinder is concentrated on a table to obtain a high-grade gravity concentrate and gravity tailings. The high-grade gravity concentrate is subject to smelting in a mixture with fluxing agents, which results in alloyed gold and slag. The gravity tailings are ground and reported to cyanide leaching. In the case of a flotation concentrate, the roast cinder is ground to minus 30 μm and subject to sorption cyanide leaching. High gold recovery (90-95%) of the target product and environmental safety are typical of the improved technology under consideration. Two national patents were granted for the methods developed to treat refractory concentrates bearing precious metals. Keywords: Gold concentrates, oxidative roasting, cinder, cyanide leaching, smelting, alloyed gold

Jan 1, 2020

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"Currently, the matted-based collection process is most widely used for platinum group metal (PGM) recovery. However, because PGM-containing concentrates are becoming more enriched with UG2 (Upper Group 2) low-grade concentrates, this is expected to be integrated or replaced with an alloy collection process.The reduction LG (low-grade) concentrates with silicon carbide (SiC) was investigated. The purpose of the study was to ascertain the feasibility of using SiC as reductant with regard to metal fall, PGM grade in the alloy, slag composition, and overall PGM recovery, and if possible, the integration of such a process in the current matte-based collection process. Rowland and Easterns LG concentrate samples from Lonmin were analysed by Xray diffraction (XRD), X-ray fluorescence (XRF), and inductively coupled plasma mass spectrometry (ICP-MS). It was found that SiO2 and MgO are the most abundant oxides and Pd is the most abundant of the PGMs. Sulphide-bearing minerals such as chalcopyrite were detected in low concentrations (below 1%), and Cr2O3 concentrations are between 2-4%. SiC reduction of Rowland and Easterns concentrate were conducted at 1600°C with reductant to concentrate ratios ranging from 2.5 to 3.5 kg SiC per 100 kg concentrate.The reduction experiments revealed that PGM recoveries from Rowland concentrate were poor. SEM images showed entrained metal prills in the slag phase. The slag viscosity at the end of the melt was calculated by using FactSage, and the results indicated that the viscosity was higher than 4 poise, which is above that of Easterns slag. PGM recoveries for Easterns concentrate were significantly better. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered in a test with a reductant to concentrate ratio of 3.5 kg SiC per 100 kg Easterns concentrate. At this reductant to concentrate ratio, Fe recovery was also the highest, at 66%. SEM imaging of a slag sample revealed few or no metal prills entrained. The FeO content in the initial concentrate charge was then increased by adding Peirce-Smith converter slag in order to decrease the slag viscosity and further increase PGM recovery. A test was conducted with the addition of 10 kg converter slag per 100 kg Easterns concentrate. The reductant to concentrate ratio was kept at 3.5 kg SiC per 100 kg Easterns concentrate. The Ir and Pd recoveries were more than 95%, while Pt recovery was almost 70%. Fe recovery increased to 76%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and Peirce-Smith converter slag were calculated. FactSage predicted that the concentrate charge should consist of 70-80% Easterns concentrate with 20-30 kg converter slag per 100 kg LG concentrate. SiC reduction of this optimum LG concentrate charge is expected to recover more than 90% of all PGMs. Cr and Si concentrations in the alloy will be below 1% in total.The effectiveness of SiC as reductant was also compared to carbon reduction. Carbon reduction of an optimum concentrate charge at the same reductant to concentrate ratio resulted in a marginally higher metal fall than SiC reduction. However, gas emissions and energy requirements are higher for carbon reduction.The study has shown that base metals and PGMs can be recovered in an iron alloy by SiC reduction of LG concentrate with converter slag additions. Integration of such a process into the matte-based collection process could be considered as a future alternative for smelting UG2 LG concentrates."

Jan 1, 2014

By Richard F. Link, Jr. Koch

"A mathematical simulation model has been devised to guide the layout of surface or underground mine workings, drill stations, and drill holes that are established in order to search for tabular ore bodies. The ore bodies may be contained within veins, sedimentary beds (including reefs), or other tabular structures.Programmed for a time-shared digital computer, the model contains both stochastic and deterministic variables. Stochastic or natural variables include the number of ore shoots and their sizes, orientations, locations and values. Deterministic or controllable variables include (i) locations and costs of workings (for underground exploration); (ii) drill station locations and costs; and (iii) drill hole azimuths, inclinations, lengths and deflections (if any).For various assumptions about the natural variables, the model is run while the controllable variables arc changed deliberately. Thus, layouts are devised to determine the percentages of the total number of assumed ore shoots found at different costs. In order to choose among the various layouts, cost-effectiveness measures are calculated."

Jan 1, 2014

The inherent weakness of the Zincor and similar iron removal processes is the relatively high undissolved zinc loss associated with the iron residue. High soluble zinc losses also occur due to poor filterability of the iron residue even though it may be limited to intermittent events. This work focussed on defining the optimum operating window for the Zincor iron removal process where iron is mainly removed in the form of amorphous, intermediate iron phases such as schwertmannite and ferrihydrite. In terms of the main operating conditions, optimum filterability was achieved under the following conditions: pH of 3.0, temperature as high as practically possible (70C), at least 25 kg/m3 seeding, and a retention time of at least 4 hours. When increasing the temperature from 60C to 70C, the required residence time decreased by almost 50%. Undissolved zinc loss was also reduced from 8% to between 2% and 3% by using a basic zinc sulphate/zinc oxide mixture as neutralising agent to effect iron removal.

Jan 1, 2003

By R. Asamoah, P. Forson, S. Xu, W. Skinner, M. Zanin

In most auriferous hydrothermal deposits, gold is preferentially associated with pyrite and arsenopyrite minerals, with higher economic gold values noted for the latter and arsenian pyrite minerals. In this paper, surface (Cryo-XPS) and solution (EDTA extraction) analysis were used to characterise pyrite and arsenopyrite minerals under different aqueous conditions involving electrokinetic study and collector interactions to better understand ways of improving the separation of pyrite and arsenopyrite. The evidence showed higher surface oxidation at solution pulp pH values in the range of 4-11 for arsenopyrite relative to pyrite. The observed highest ratio of pyrite to arsenopyrite selectivity was 1.7 at collector concentration of 50 g/t and decreased with an increase in collector concentration. Keywords: EDTA extractable iron, selectivity index, differential flotation, grade engineering

Jan 1, 2020

By B. M. Wainstein

An extension of lognormal theory and its application to risk analysis models for new mining ventures by B. M. WAINSTEIN*, B.Sc., M.B.A. (Witwatersrand) (Visitor) The lognormal distribution, which remains the most popular distribution model for ore values, is investigated. The T-distribution, an integral part of this theory, is dependent on the sample size, n, and the unknown population parameter, o2, which cannot be integrated out. Hence, o2constitutes a nuisance parameter. In this study, the robustness of the T-distribution to changes in o2 is examined. It is found that the T-distribution is robust for 0,1 <= o2 >= 2,5, a domain covering most practical applications of the lognormal theory. By the use of o2 = 0,7, multiplier factors, which facilitate the computation of the confidence limits, are derived for a comprehensive set of confidence levels.

Jan 4, 1975

By R. G. Diale, H. R. Chauke, T. M. Ledwaba, P. E. Ngoepe

FeCo alloys play an important role in soft magnetic materials with a wide range of technological applications due to their high saturation magnetization and Curie temperature. However, these alloys have low ductility at room temperature. The ductility can be improved by the ternary addition of elements such as V. A density functional theory supercell approach was used to generate B2 Fe50Co50-xVx (0 ≤ x ≤ 50) structures and the properties were evaluated at different atomic percentage compositions to determine the ductility at room temperature. The structures were fully optimized to obtain better equilibrium ground-state properties such as lattice parameters and thermodynamic properties for both binary and ternary systems. The stability of Fe50Co50- xVx was evaluated from the heats of formation, elastic properties, and phonon dispersion curves. Furthermore, magnetic strength was evaluated from magnetic moments. It was found that all structures are thermodynamically stable due to the negative heats of formation. The calculated Pugh’s ratio and Poisson’s ratio confirm that alloying with V effectively improved the ductility. It was also found that Fe50Co50-xVx showed a positive shear modulus for the entire concentration range investigated, in agreement with phonon dispersion curves. The ternary addition of V to the FeCo system resulted in reduced magnetic strength due to a decrease in magnetic moments. These findings reveal that B2 FeCo-V alloys can be used as components and actuators for the automotive industry.

Jun 10, 2024

By P. van der Westhuyzen

Gone are the days of stock-standard diamond beneficiation and final recovery circuits that could, with minor modifications, be adapted to treat any diamond-bearing ore source. A new era has dawned, offering the opportunity to streamline existing diamond processing operations or develop simpler, more efficient, and economical diamond processing plants, with the focus on more efficient comminution, beneficiation, and final recovery. This change in scene has been brought about by: ? The introduction, rapid development, and maturation of multiple comminution, sorting, and recovery technologies ? The need to adapt to a new standard of project approach post the commodity super-cycle phase, where optimizing existing operations and developing scalable, ?fit for purpose? new mines are fast becoming the norm in diamond processing plants in both primary and alluvial operations ? The quest for energy efficiency and lower labour costs ? More remote and inaccessible reserves (under lakes, tops of mountains etc.). This paper serves to identify some technology advances and demonstrates how these could be considered as replacements for or in combination with conventional technologies to arrive at an optimum techno-economic solution. To name a few applications/technologies: ? Comminution: conventional cone crusher, modified/specialized cone crusher, and the high-pressure grinding roll (HPGR). Although significant advances have been made in recent years, this paper only briefly covers comminution within the beneficiation circuit design ? Waste sorting: NIR (near-infrared) sorting, optical (colour) sorting, XRF (X-ray fluorescence) ? Primary concentration by combining dense media separation (DMS) with either XRT (X-ray transmissive), pulsed X-ray, jigs, or pan plants depending on the application, scale, and economics ? Final recovery of diamonds with either conventional X-ray technology, pulsed X-ray technology, or XRT. From recent studies, it can be concluded that there is no longer a standard solution, but rather the ?right? or appropriate solution. Through combining a sound knowledge of the ore source (ore dressing studies or onmine data gathering) and leveraging off the advances in technologies, one is able, through trade-off studies, to arrive at the ultimate techno-economic configuration, the ?right? solution. Emphasis is placed on maximizing diamond recoveries through appropriate technology selection and minimizing the associated costs in an effort to de-bottleneck or improve efficiencies of existing diamond processing plants, or to arrive at the ideal new diamond process plant design..

Jan 1, 2014

By B. Amankwaa-Kyeremeh, W. Skinner, R. K. Asamoah, C. Greet

With the continuous increase in ore mineralogical complexity coupled with decreasing head grades, there is a need for mining industries to process large tonnages of material to meet global metal demands. Smarter, cheaper techniques are required to better map ore mineralogical variations proceeding to pre-concentration (flotation) stages for higher performance and metal recoveries. This paper is aimed at briefly reviewing previous studies on different selected ore mineralogy, with the focus on their pulp chemistry, to identify relationships which aid quicker flotation feed variation monitoring. Very little published work exists linking pulp chemistry parameters to flotation feed mineralogical variation. A successful application implies maximising grades at higher metal recoveries and reducing the cost of reagent for a better performing flotation circuit. Keywords: Mineralogical variation, flotation, pulp chemistry

Jan 1, 2020

One of the important facets of The South African Institute of Mining and Metallurgy is its service to its members. One way of achieving this objective is by pursuing an active branch structure. In this Spotlight, Richard Beck, Holder of the Regional Development Portfolio, gives the aims of the Institute&apos;s branches, with a short note on each branch prepared by the regional chairman. Aims of the Branches: The primary aims of the Branches of The South African Institute of Mining and Metallurgy are those of the Institute itself: to further the interest of its members, to uphold the status of the mining and metallurgical profession, and to promote the image of mining and metallurgy. Beyond these &apos;high&apos; objectives, the branches have a special function in providing a more intimate relationship between the Institute and its members. The branches enable members who live outside the Johannesburg area to participate in the affairs of the Institute to an extent that would not otherwise be possible and that they themselves can define. This is achieved through the holding of social events, colloquia, and visits.

Jan 1, 1990

By P. J. D. Lloyd, Jill Urban, M. R. Urban

The adsorption of gold from cyanide solutions onto constituents of the reef, and its role in reducing the efficiency of the gold-recovery process by M. R. URBAN. M.Sc. (Chem. Eng.) Rand (Visitor). JILL URBAN. B.Sc. (Chem. Eng.) Rand (Visitor) and P. J. D. LLOYD. Ph.D. (Cape Town) (Fellow) Evidence for the adsorption or re-precipitation of gold from cyanide solutions onto gangue minerals of the Witwatersrand reefs has been gathered over a number of years by various investigators. The evidence from tests using radioactive tracers is conclusive and indicates thlt adsorption contributes about 0,1 g/t to the total gold loss from conventional reduction works. The loss is a function of the alkalinity and cyanide concentration of the solution, and it appears to be affected by the extent of time between milling and cyanidation. The heavy minerals appear to be the strongest adsorbers, and the clay minerals somewhat less strong adsorbers. A sensitive qualitative test based on thin-layer chromatography permits the extent of adsorption and desorption to be readily determined.

By R. A. H. Lycett, P. R. Jochens, D. D. Howat

The crystallization of rutile from titaniferous slags by R. A. H. LYCETT, M.Se. (Eng.),"A.M.I.M.M. (Visitor), P. R. JOCHENS, Pr. Eng., M.Se. (Eng.) (Rand), Ph.D. (Member), and D. D. HOWAT, B.Se., Ph.D., F.R.I.C., F.I.M. (Fellow) Factors affecting the precipitation of rutile from smelter slags were investigated, with particular reference to the effect of additions of phosphorus pentoxide to the slag. The phases were identified and the phase boundaries determined for slags having phosphorus pentoxide additions of 0 to 50 per cent. The liquidus temperatures of these slags were determined, and a pseudo-binary phase diagram was constructed. Rutile crystallized as the primary phase from melts having a phosphorus pentoxide content of more than IS,S per cent. Prismatic rutile crystals whose TiO. content was more than 97 per cent were grown from melts that had a phosphorus pentoxide addition of 30 per cent. However, the morphology of the precipitated rutile was such as to make subsequent separation impracticable.

Jan 9, 1975

The September General Meeting of the Institute was held in Kelvin House, Johannesburg, on 16th September, 1970, at 3.00 p.m. Mr V. C. Robinson (President) was in the Chair. There were also present one hundred and eighteen Fellows, including Dr J. M. Bereza, H. P. Carlisle, R. J. C. Goode, Dr J. P. Hugo, P. Lambooy, Prof R. P. Plewman, W. W. Malan, Dr J. T. McIntyre, Dr M. D. G. Salamon, L. W. P. Van den Bosch, P. A. von Wielligh (Council Members), A. Bain, G. P. Bennet, D. L. Carson, G. L. H. Diering, M. E. E. Douglas, F. A. B. Fouche, R. Fourie, A. R. C. Fowler, E. B. Gordon, J. S. Hay, G. H. Henderson, S. D. Hill, A. C. Hofmeyr, J. M. Jacobs, A. F. Lee, D. G. Malan, L. J. Prince, W. G. Pyne-Mercier, A. H. Mokken, Dr W. S. Rapson, R. R. Richardson, H. V. Solomon, C. G. Sowry, G. G. Stanley, G. R. Still, D. L. Starkey, D. L. Taylor, E. W. Thiel, I. E. Van Aswegan, M. van Ryneve1d Steyn, N. B. Vinson, H. Wheeler, Dr A. Whillier, R. A .Wilson, C. F. Ziervogel. Forty-two Members including R. C. Bertram, F. Collier, G. C. Currie, O. Davel, J. M. Gosnell, A. Hazell, Dr N. C. Joughin, F. Kleinschmidt, D. Love, R. B. Macgillivray, D. Mather, R. D. R. Munro, R. S. Pearson, J. J. Peisl, T. J. Pole, A. J. Rossouw, R. G. B. Skirving, G. S. Schwartz, K. Stee1e, H. A. G. Slater, A. Taylor, B. A. Thomas, P. L. Vaughan, D. T. Watt, W. Wilson. Nineteen Associates including R. K. Briggs, S. I. Du Preez, P. G. Gaylard, P. H. Hartslief, W. M. Mackay, A. D. Ross. Three Students: V. S. Care, R. J. Drummond, P. J. Pretorius. Thirty-one Visitors including C. P. S. Barnard, D. W. Bosch, M. Bain G. L. Brown, G. D. Behrens, C. Coetzer, D. M. Gilbart-Smith, R. L. Man, Dr G. J. Stander, M. W. L. Steinobel, R. H. E. Thorpe, T. D. van Wyk, P. H. van Zyl, E. Vereecken, J. J. H. Viljoen. Secretary, D. C. Visser. Total present: 215. OBITUARIES The President: "It is my sad duty to announce the death of the following: Bruce Donaldson Crawford, Fellow, who joined the Institute in 1951 and passed away on 29th April, 1970. Donald Joseph Powrie, Life Fellow, who joined the Institute in 1935 and passed away on 22nd July, 1970. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments&apos; silence." MEMBERSHIP The President: "I have much pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Associate: WiIliam Norman Carter. Students: Roman Michael Dabrowski, Sean George Dean Eaton, Alan Philip Stonham Howard, Anton du Preez Roos, Richard Harold Tourle. MEMBERS TRANSFERRED TO A HIGHER GRADE From Graduate to Member: Terrance Alexander Ward. From Associate to Member: Bernard Andre Thomas. "I welcome the newly elected members to the Institute and congratulate the members who had been transferred to a higher grade." CO-OPTION The President: "I wish to advise members that, in terms of clause 3.9 of the Constitution, Mc. H. P. Carlisle had been co-opted to serve on Council." PAPERS FOR PRESENTATION The President: "We have two papers today, and I am first going to call on Dr Stander the Head of the Water Division of the C.S.I.R., who IS well known to many of you for his work and talks on pollution, who has had more than a little to do with this industry, and who has been I would say, of the greatest possible assistance to the mining industry in overcoming the problems of pollution which are so prevalent in industry of this nature. He, Mr Henzen and Mr Funke have written this paper, &apos;The disposal of polluted effluents from mining, metallurgical and metal-finishing industries, their effects on receiving water and remedial measures.&apos; This is the Water Year, as you know, and it is most appropriate that we should have such an authority to talk to us on this very important topic. I now have much pleasure in asking Dr Stander to introduce his paper." After the presentation of the paper the President said, "Gentlemen, I am sure that you would like me on your behalf, to thank Dr Stander very sincerely for a paper which I think has enabled us to get a completely new slant on the Water Year. There are many people who have put their finger on this campaign and said, it is all a gimmick. There are others-I suppose notably some of the bridge clubs which operate on week-day afternoons in Parkview-who seem to think that this is a quick way of getting early rain. Of course, it is not. This is a most important paper which we have had given to us this afternoon. You probably found it here when you arrived and have not read it-I was very lucky to be able to read it last night, and there is an awful lot of meat in it. For as long as I have been associated with mining in any way, there has been a problem of polluted effluent-of effluents carrying a mineral load from mining, and I think Dr Stander is absolutely right-and, of course, the Commission is right when they say that this is not merely the problem of mine management or mine owners-this is a problem which affects every single human being in this country.

By S. W. Robertson, M. T. Golela, S. Mxinwa

South Africa has one of the largest Cr-related industries in the world and generates large amounts of Cr-containing smelter dusts. It is normal practice to scrub Cr from the furnace off-gas in water, and to recover the Cr by adsorption, followed by recycling of the loaded adsorbent into the furnace. A study was conducted to find a low-cost adsorbent that is capable of removing sufficient Cr from the solutions generated by scrubbing. The test work focused on the evaluation of different clay minerals (attapulgite, bentonite, and kaolinite) as adsorbents for Cr. Cr(VI) could only be adsorbed after prereduction with e.g. ascorbic acid (ASA). An 80% removal of Cr(VI) could be achieved from a solution containing 20 mg/L Cr using bentonite clay after reduction with ASA. Attapulgite and kaolinite adsorbed less than 55% Cr after reduction with ASA. Both ASA and ferrous salts were found to be suitable reducing agents. The use of acid mine drainage (AMD) was also investigated as a low-cost alternative reducing agent, as AMD usually contains iron. The Cr(VI) reduction potential of the AMD was determined by redox titration against a solution containing 50 mg/L Cr(VI). Studies show that AMD can potentially be used as a reducing agent in a Cr removal process if it is available on site.

Feb 12, 2024

By D. Marcotte, R. V. Dutaut

In most exploration or mining grade data-sets, the presence of outliers or extreme values represents a significant challenge to mineral resource estimators. The most common practice is to cap the extreme values at a predefined level. A new capping approach is presented that uses QA/QC coarse duplicate data correlation to predict the real data coefficient of variation (i.e., error-free CV). The cap grade is determined such that the capped data has a CV equal to the predicted CV. The robustness of the approach with regard to original core assay length decisions, departure from lognormality, and capping before or after compositing is assessed using simulated data-sets. Real case studies of gold and nickel deposits are used to compare the proposed approach to the methods most widely used in industry. The new approach is simple and objective. It provides a cap grade that is determined automatically, based on predicted CV, and takes into account the quality of the assay procedure as determined by coarse duplicates correlation.

May 1, 2021

By R. G. B. Pickering

Successful management of mining operations depend on the accurate and reliable measurement of performance as a monitoring instrument in a feedback and control loop. However, when changes are being considered, the probable effect of the change on bottom line results requires different measuring techniques incorporating an in depth understanding which can identify hot spots in the operation which exhibit strong sensitivity to change. The CSIR&apos;s Division of Mining Technology has therefore been devoting a considerable effort to the establishment of techniques which enable changes to be analysed in terms of their impact on the two key parameters describing mine performance, i.e. profitability and safety. This paper describes these techniques, outlines their application to some example situations and discusses planned enhancements. The first section of the paper addresses the profitability model, and this is followed by a section considering the mine safety model.

Jan 1, 1996