Search Documents

Coal is found in the northeast comer of Georgia, in Dade, Chattooga, Walker, and Floyd Counties. Five seams, which underlie all of Lookout, Sand, and Pigeon Mountains, have produced most of the coal mined in the state. Representative analyses of Georgia coals show that they are typically low sulfur (less than one to one percent), low-to-medium volatile, bituminous deposits. Although there is no active mining in the state, reclamation continues on several permitted areas. In 1983 the State of Georgia relinquished primacy to the Office of Surface Mining. Since that time permits have been issued and mining completed. All the sites are presently in the process of bond release.

Jan 1, 1992

By T. E. Marshall, D. R. Dolinar, T. M. Barczak, T. P. Mucho

Over a portion of the older limestone mine workings at the NIOSH Lake Lynn Laboratory, a mining health and safety research facility, a large sinkhole formed caused in part by the intersection of several tightly spaced joint sets and unusual weather conditions. The anticipated propagation of the associated roof failures threatened to encroach upon a portion of the facility’s secondary escapeway. To protect the escapeway, two cribs walls and over 80 cable bolts were installed. In addition, extensometers were installed to monitor roof movement in the escapeway. However, a large roof fall associated with the propagating roof failures in the sinkhole area partially destroyed one crib wall where the adjacent escapeway was not reinforced by cable bolts. Recent roof movement information indicates that this area is still active. Based on these measurements, steps have been taken to stabilize this portion of the escapeway. This paper discusses roof monitoring, the roof movement, the large roof fall, propagation of the roof failures, and the recent support measures undertaken to stabilize the escapeway.

By Charles Vaught, Kathleen Kowalski

Emergency personnel, like all workers, carry out their duties within an environment composed of a set of discrete elements. First, there is the emergency itself. Whether a forest fire in France, a tornado in the American Midwest, or a mining disaster in Russia, the emergency imposes certain exigencies upon the responders. Second, a social structure exists with specific social units, rules, and forms of association. An emergency response, therefore, takes place within a context of prescribed behaviors, expectations, and value judgments that are sometimes in conflict with each other. Third, there is a technology that must be understood in order to accomplish group goals. If the technology itself is implicated in the emergency, the entire emergency environment may be impacted. Clearly, a breakdown in any of these elements could result in worker injury and might heighten responder stress. This paper discusses how emergency workers not only get injured but may come to experience bum-out, post-traumatic stress syndrome, or impaired work and family relationships, even though their normal work setting (the emergency) is expected to be 'abnormal'. The authors suggest areas in each of the three environmental elements that, deserve further inquiry.

By Gerald T. Homce, Michael R. Yenchek, H. Kenneth Sacks, James C. Cawley

Abstract—Overhead electric power lines present a serious electrocution hazard to personnel in a variety of industries. Overhead lines, typically uninsulated conductors supported on towers or poles, are the most common means of electric power transmission and distribution, and are exposed to contact by mobile equipment such as cranes and trucks. Equipment contacting energized overhead lines becomes elevated to a high voltage, and simultaneous contact by personnel of the “hot” frame and ground can cause serious electrical shock and burns. Industries where risk of these accidents is greatest include construction, mining, agriculture, and communications/public utilities. An estimated 2300 accidental overhead line contacts occur each year in the U.S. This paper describes a practical low-cost concept to detect actual contact of mobile equipment with a high-voltage line and provide a warning. Accident statistics indicate that more than half of the fatalities could be prevented by such a device. Index Terms—Crane, electrical shock prevention, engineering control, mining, mobile equipment, power line.

Miners, like everyone else, must be able to see well in order to work well. But simply hauling bigger and brighter lights into the mines does not necessarily produce better mine illumination. This chapter tells why. Increasing the power of the light source can create problems of portability, glare, adaptation and contrast. This chapter also discusses some ways to increase illumination by Improving the reflectability of walls, roofs and other exposed surfaces. In Chapter IV you learned that the "brightness" of a room or work area was really a matter of how much light was reflected from the walls, roof, and other surfaces. Therefore, if you want to Improve visibility you should increase the amount of reflected illumination. O HOW DOES ONE DO THAT? One way of Increasing reflected illumination would be to increase the power of the light source.

Jan 1, 1976

By Stephen P. Signer

This paper presents an overview of laboratory and field tests on approximately 250 fully grouted roof bolts instrumented with strain gauges in order to study loading behavior. Laboratory work included pull tests, time-dependent tests, and shear tests. The field tests were conducted in 14 different mines extracting different commodities. However, because of the focus of this publication, only the results of tests in 9 coal mines are reported here. In the field tests, all but 14 bolts were loaded by rock movement; these 14 bolts were tested using pull gear. The variables studied included anchorage length, mechanical interlock, time-dependent behavior, shear, installation load, loading rate, and maximum load level. Such information will improve the understanding of the behavior of resin-grouted bolts, which in return will enhance the safety of miners by reducing the occurrence of rock falls. The influences of geology, overburden depth, entry width, mining-induced stresses, and bolt spacing are not described.

Jan 10, 2000

Volumetric measures [ ]

Jan 1, 1960

The Ringelmann Smoke Chart fulfills an important need in smoke abatement work and in certain problems in the combustion of fuels. A knowledge of its history and method of preparation is, therefore, of interest to many. Since instructions on its use are not shown on the recent edition of the chart, those included in this revision of the previous Bureau of Mines publication now are a necessary complement to the chart. More detail regarding the use of the chart is included than was given in the earlier version.

By Edward A. Barrett, Launa Mallett, Charles Vaught, Kathleen M. Kowalski, Michael J. Brnich, Lynn L. Rethi, Robert Randolph, William J. Wiehagen

The goal of the Pittsburgh Research Laboratory's training research is to explore the relationship between valid instruction and improved worker performance. Studies summarized in this paper include: (a) the development and assessment of training techniques that strengthen miners' ability to act competently in emergencies; (b) investigations of classroom simulations that enhance the perceptual, judgment and decision making skills of workers confronted with mine hazards; and (c) field studies of the linkages between financial investments in occupation at skills training and measurable outcomes.' The authors maintain that better ties between training and performance will aid long-term human resource development. The best way to establish this connection is through the use of objective and reliable data.

By Gerald L. Finfinger, Syd S. Peng

Geology is an integral part of roof control, mine design, and production operations. Yet, the importance of geology, coal/rock as an engineering construction material and its properties and behavior within the planned mine areas, in overall mine production operations has not been hilly appreciated. Of all of the engineering disciplines, mining engineers work with the most challenging construction materials. They must deal with rock materials as they exist in their natural states and design mine structures without well-known and defined properties. Further complicating the design process is the variability of the in-situ rock materials with rock types and rock properties varying widely from place-to-place. Predicting properties in advance of mining is difficult and oftentimes impossible. This is why some types of roof-control failures may suddenly occur in some areas when a single roof-control technique is consistently applied to an entire panel, section, or mine. Many roof-control techniques are primarily applicable to the geological conditions that were assumed in the development of those techniques and variations of the rocker rock properties may require modification or significant redesign of the support technology.

By David Gearhart, Thomas Barczak

Hydraulic cylinders a re used in several roof support systems, such as longwall shields and mobile roof supports, to provide critical ground control Many state-of-the-art hydraulic support systems operate at pressures as high as 7,000 psi to provide the necessary support capacities. Pressure in the upper stages of multi-stage cylinders can be intensified by a factor of 2 or 3 providing pressures of 20,000 psi or greater. A proper understanding of the operation of these high pressure systems is necessary to safely maintain and repair these support systems. Likewise, the performance characteristics need to be fully understood to evaluate the impact of design parameters on the capability of the support to maintain effective ground control. This paper examines the basic operating principles of state-of-the-art hydraulic cylinders and discusses relative issues pertaining to. (1) setting loads, (2) support stiffness, (3) yielding behavior, (4) errors in assessing support loading, and (S) hydraulic failure mechanisms and how to detect them

To improve electrical safety and lengthen light bulb life on trolley haulageways. Approach A resistor inserted in series with each pair of light bulbs, decreases the voltage applied to the bulbs and eliminates heavy arcing when voltages rise. How It Works Under certain conditions, incandescent light bulbs connected directly to a 300-volt d-c trolley wire can be a hazard, particularly during weekends when electrical equipment is nut in use. When little electrical power is being used, the voltage (on the trolley lines and at the substation) can rise to a value which will destroy the bulb filament, cause arcing, and damage the bulb holder. In one coal mine where light bulbs in certain locations fre¬quently failed, the problem was overcome by inserting a 100-ohm, 50-watt resistor in series with each pair of light bulbs. The light bulbs are rated at 300-volts and 100-watts. Figure 1 shows the light bulbs and resistor circuit. This resistance was added in order to reduce the current through a short circuited bulb holder, from several hundred amperes to a much safer value of 3 amperes. However, the resistor in series with each pair of light bulbs, also reduces the voltage across the lighted bulbs to approximately 240 volts during periods when the trolley line voltage is up to 300 volts. With this arrangement, no light bulb failures occurred over a 6-month period. The resulting light reduction has not been objectionable.

Jan 1, 1976