Search Documents

By Deno M. Pappas, Christopher Mark, Eric R. Bauer

During 1998-99, groundfall incidents resulted in 27 fatalities and were responsible for over 70% of all deaths in U.S. underground coal mines. To obtain a better understanding of where and why these incidents occurred, a comprehensive analysis of ground fall injuries and fatalities was conducted. The first portion of the study examined various factors associated with roof and rib fall injuries and reportable roof fall noninjuries that occurred during 1995-98. The study found that the room-and-pillar mining method has twice the groundfall incident rate than the longwall method. Mine locations with high groundfall rates seem to correlate to regions where there is a higher concentration of problematic coalbeds. For example, the Illinois Basin has very high groundfall rates, which can be traced back to several key coalbeds-Kentucky No. 13, Herrin/No. 6/Kentucky No. 11, and Springfield No. 5/Kentucky No. 9. High rib fall rates were found in mines located in thick seams. Groundfall rates were found to be 30% to 40% higher during the months of July through September, possibly due to high humidity that may cause the shale mine roof to deteriorate. The second part of the study examined the root causes of failure by reviewing all groundfall fatality reports for 1996-99. Primary and secondary hazard factors were assigned to each groundfall incident. The primaryf actors resulting in these groundfall fatalities were pillar extraction, traveling under unsupported roof, skin failure, construction, longwall faces, intersections, and geologic discontinuities. Defining prominent ground control incident trends and hazards will identify areas where additional study is needed and where innovative solutions need to be developed to reduce these severe occupational hazards.

Jan 10, 2000

By Joseph A. Holmes

The perpetuation of the supply of anthracite coal in Pennsylvania is a national as well as a State problem. Any investigation that shows how larger percentages of this coal may be saved in mining, without excessive cost, and without dangerous subsidence of the overlying surface ground, has a national as well as a local interest. Messrs. Conner and Griffith, who conducted the investigations described in this report largely for the city of Scranton, are consulting engineers for the Bureau of Mines for investigations similar to those they have already made in connection with their Scranton work; and this report is published by the bureau in response to numerous requests, because of the fact that the information it contains will prove useful in the general solution of similar problems in many of the country's coal fields. A study of the accompanying maps will show that the city of Scranton is underlain by 11 separate beds of coal, varying in thick- ness from 2 to 24 feet. It is estimated that before mining opera- tions were begun these beds of coal contained underneath the present city limits of Scranton 600,000,000 tons of coal. The 27 collieries operating within the city limits, working independently of each other, had excavated and removed, up to March, 1911, an aggregate of 198,000,000 cubic yards of coal and accompanying rock, or 3,000,000 cubic yards more than the total amount of material excavated and to be excavated by the United States in constructing the Panama Canal. This fact illustrates something of the magnitude of the problem that the city of Scranton, with the aid of these engineers and of a special commission or advisory board, has undertaken to solve. The excavation has included 177,000,000 tons of coal and 44,000,000 tons of rock and accompanying refuse. This leaves about 420,000,000 tons of coal still to be removed. As a result of other investigations and of experience in adjacent anthracite mines, Messrs. Conner and Griffith and the advisory board of engineers have advised that, as far as may be necessary to prevent dangerous surface subsidence, the spaces remaining beneath the city of Scranton from the excavation of the above-described material should be filled with sand and other materials by flushing or other processes. This operation is expensive, but it is believed to be not beyond the reach of what is practicable, nor in excess of the value of the coal that may be removed and the amount of damages that may result from the caving in of the surface if such a plan is not carried out. No one realizes so fully as do the authors of this report the need of additional tests and other investigations before the data now pre- sented by them can be fully accepted as sufficient for all purposes in the solution of the problem; and it is expected that at some early date a more extensive series of similar tests can be made by the Bureau of Mines under the supervision of Messrs. Conner and Griffith on a larger scale and under a greater variety of conditions. The field examinations made for the Bureau of Mines by N. H. Darton, which are described briefly in a chapter of this bulletin and will be discussed at length in a bulletin to be published later, indicate the extent and distribution of the sands, gravels, and other materials in the Scranton-Wilkes-Barre district available for flushing purposes if further tests indicate their relative merits; and it is expected that the relative merits of these different materials will soon be tested under such conditions as will furnish the desired information.

Jan 1, 1912

By N. S. Dalal, W. Irr, X. Shi, V. Vallyathan

"Inhalation of crystalline silica is associated with a biphasic biologic response of acute cell injury and chronic pulmonary fibrosis. Dust induced cell membrane injury leading to the release of lysosomal enzymes and cell death has been implicated as the initial important biologic event triggering the fibrosis. However, it ls also possible other biologic reactions could alternatively, or in addition to these enzyme related cytotoxicity reactions, alter the normal functioning of cells. It is well known that phagocytic activation results in the production of oxygen radicals which are highly cytotoxic to cells. In healthy - lung, protection against the toxic effects of the normal balanced ·biologic reactions are provided by a number of defen1e systems including antioxidants. In disease or condition of overproduction of oxygen radicals, biochemical protection may be overwhelmed with resultant cellular injury.Our recent observations have shown that reactive oxygen radicals (ROR) are generated during grinding of crystalline silica. We hypothesized that these newly generated RORs may cause cell injury, lipid peroxidation, or even damage to macromolecules such as DHA. Biochemical aberrations caused by the inhalation of crystalline silica with ROR at occupational settings might overwhelm cellular and antioxidant defense systems of the lung leading to injury and subsequent fibrosis.To test this hypothesis, we have investigated the generation and decay of ROR produced by crystalline silica using electron spin resonance (ESR) and investigated its toxicity with conventional biologic tests at various time intervals after grinding. We also studied the decay of these newly generated RORs in buffer and the effect of antioxidants and scavengers in the abolition of cellular damages."

Jan 1, 1989

By Lon D. Santis

The Code of Federal Regulations Title 30, Parts 56, 57, 75, and 77 require that detonators and explosives be separated by four inches of hardwood or equivalents when transported together in mines. This standard was developed to protect the explosives from initiation by the more sensitive detonators. The research reported here is an attempt to quantify the fire protection offered by four inches of red oak and other materials. Boxes with a volume of 6.75 cubic feet were made from four-inch thick rough green oak (RGO), two-inch thick RGO plied, two-inch thick #1 common (dried) red oak plied, and a metal/plywood composite. These and boxes meeting the Institute of Makers of Explosives' (IME) Safety Library Publication No. 22 were tested in bonfires. The boxes were instrumented with thermocouples, filled with detonators, and placed over a kerosene fire imparting about 16 kilowatts per square meter heat flux for up to 3 hours. Tests showed that the wood boxes protected the detonators for over an hour with variations between the different trials. In the IME 22 container tests, detonators began exploding in as little as 17 minutes in one test and not for 2-/12 hours in another test. Detonators in the metal/plywood boxes began to explode in about 15 minutes but with minor alterations, were able to contain the detonators. The test results show that the exterior of an IME 22 container significantly affects its thermal properties. Defects in the form of cracks and the manner in which the container is closed have a significant effect on the performance of a detonator container in a fire.

By L. C. IlsLey

A preliminary investigation has recently been made by the U. S. Bureau of Mines to determine whether or not the ordinary mine- type telephone is entirely safe in gaseous atmospheres . Two well known makes of mine- type phones were purchased for this investigation . It is not conceivable that the current necessary for talking over telephones could ignite gas . However , such phones are provided with efficient magnetos , and it was believed that danger might result from the ringing of the magneto . Again , while this type of phone has been designed to have a certain measure of dust and moisture tightness , evidently it has not been designed as an explosion- proof device . either with regard to cover joints and fastenings or strength of castings . Therefore , the problem was simplified . First it was assumed that owing to the construction of the telephones the gas would penetrate into their interior , and the question was to ascertain whether or not the gas would be ignited from the operation of the magneto .

Jan 1, 1922

By G. Molinda, D. Dolinar

Each year, about 2,000 falls of supported roof occur in the more than 800 underground U.S. coal mines. Therefore to help improve the design of primary support systems, the National Institute for Occupational Safety and Health (NIOSH) conducted a nationwide study of roof falls in over 2,500 km of roadways at 37 coal mines. Information on the roof falls as well as other geotechnical, mining, geologic and roof bolting factors were collected and quantified Then a multi variate statistical analysis was conducted on the data with the roof fall rate being the outcome variable The results were used to derive preliminary design guidelines for predicting the roof bolt length, capacity, and pattern required to effectively reduce the roof fall rate. The equations are fairly limited by a relatively high statistical variance in the data. Also reported is a recent survey of U.S roof bolt manufacturers that shows a significant change in bolt types used over the last ten years.

By George T. Faust

The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the various types of clays to be found in the Southern States. In connection with this work, the petrographic laboratory is called

Jan 1, 1940

By R. J. Matetic

The National Institute for Occupational Safety and Health (NIOSH) has recognized that Noise-Induced Hearing Loss (NIHL) is the most common occupational illness in the United States. The use of heavy equipment, the drilling of rock, and the confined work environment are some of the factors that contribute to high levels of noise exposure to workers in the mining industry. Every day 80% of the nation’s miners go to work in an environment where the time weighted average (TWA) exceeds 85 dBA. Moreover, 25% of the miners are exposed to a TWA noise level that exceeds 90 dBA, the Permissible Exposure Limit (PEL). Furthermore, a NIOSH analysis of a large sample of audiograms showed that at age 50 approximately 90% of coal miners and 49% of metal/non-metal miners have a hearing impairment. By contrast, only 10% of the non-occupational-noise exposed population has a hearing impairment at age 50 (Franks, 1997) (Stephenson, 1998). Simply stated, the majority of miners have a hearing loss by the time they retire. While NIHL is the most common occupational disease in this country, this problem is especially acute among workers in the mining industry. There are several barriers to reducing NIHL in the mining industry. These include: gaps in knowledge of noise dose/source relationships, the unavailability of effective noise controls, and needs for worker education and worker empowerment. A related issue is the difficulty of communication in noisy workplaces by both hearing impaired and normal hearing workers. The Pittsburgh Research Laboratory (PRL) at NIOSH has strategically developed a hearing loss prevention program for overcoming these respective barriers in an attempt to reduce NIHL in the mining industry. This paper provides an overview of the research program being conducted at the PRL.

By Oliver Bowles

"In a previous report of the Bureau of Mines (Serial No. 2080 reference was made to a fatal accident from falling rock in a quarry in Utah, and ways of avoiding such accidents were pointed out. A fatal accident similar to it in some respects recently occurred in a limestone quarry in Maryland. All operators of stone quarries are desirous of reducing accidents to a minimum, and almost without exception they welcome any suggestions having in view the establishment of safer quarry practice. It is believed, therefore, that a brief outline of the cir-cumstances surrounding this later accident may be of practical advantage to quarry-men, as it may serve as a guide to them in so conducting operations that such unfortunate occurrences may be reduced in number.The quarry where the accident occurred is in form a circular pit 500 to 600 feet across an 80 to 100 feet deep. The rock is a dense limestone with the beds dipping at an angle of 35 to 45 degrees from the horizontal. Numerous erosion cavities in the form of pockets or narrow spaces following joint planes are filled with red sand and clay. They are confined largely to the upper 20 or 30 feet of the deposit. Open bedding planes are 4 to 10 feet apart toward the surface, and are spaced at wider intervals toward the base of the quarry. The open bedding planes present smooth uniform rock surfaces that dip steeply into the pit at the northeast side of the quarry opening. These smooth surfaces constitute a source of danger, as they may permit loose material to slide into the pit.In this particular instance a blast had been discharged, throwing down a mass of rock for steam-shovel loading. Three men wore employed thereafter for a period of about two days in cleaning down all loose material that might be dangerous to workmen luring the loading process. A mass of red sand and clay in which several large bowlders were embedded was left on one of these slanting surfaces, for the material seemed to be sufficiently secure to be quite safe. The lower edge of the slanting surface was about 25 feet above the quarry floor. The quarry conditions are illustrated in fig. 1, where (a) represents the quarry floor, (b) the vertical quarry (c) the slanting joint plane surface, and (d) the rock and earth resting on the surface."

Dec 1, 1921

Acid pollution from abandoned mines causes serious contamination of major streams in coal mining areas. In Pennsylvania alone it is estimated that 3000 miles of streams are devoid of fish and plant life because of coal mine effluent.1 The pollution arises because water and oxygen react with iron sulfide in the mine cavity to produce sulfuric acid and iron sulfate, which later find their way back into surface streams. Two general approaches to the problem are possible: (1) prevent the acid-forming reaction from taking place, (2) treat the acid mine water after it is formed so that it will not be harmful to the ecology when discharged into streams and other surface waters. The work described in this report belongs in the first category - it was based on the assumption that acid formation in the mine cavity can be prevented by keeping water (one of the reactants) out of the mine. This was to be accomplished by-forming a waterproof seal over the mine cavity which would prevent the seepage of surface water into the mine. It was planned to form such a seal at or near the surface of the ground by applying latex to the soil. Ideally a dilute latex would be applied to the soil and would penetrate to a depth of two to three feet below the surface where it would be coagulated by reacting with a constituent of the soil or by other means., A seal below the surface of the soil would have several advantages over a surface seal - it would not be subject to destruction by traffic, frost or vegetation and, more important, it would allow the use of the top soil for many agricultural purposes. A preliminary feasibility experiment was performed prior to application for the present grant. It showed that it was indeed possible to form a sub-surface seal by means of latex. A core of soil was obtained locally (Wayne, N. J.) by driving a 6.5 cm inside diameter steel pipe about 100 cm long into subsoil for a distance of 71 cm. The soil was retained within the pipe for this experiment. A part of the free space above the soil in the pipe was charged with water, and the seepage rate of the soil after it had become saturated was 15 ml/min under a total head (wet soil plus supernatant column of water) of 92 cm. After the supernatant water had drained completely, 100 ml of 5% rubber latex was added and allowed to seep into the soil. This was followed by additional water and the seepage rate was found to be 2 ml/min under the same head. This seepage rate remained unchanged when remeasured on the following day. Since there was no visible evidence of the latex in the collected drain water it is presumed to have been retained by the soil.

Jan 1, 1972

Improve the field-of-view into the front-right blind spot for drivers of large haulage trucks, thereby reducing the growing collision hazard in surface mines. Approach Reduce the glare problem found in the first generation fresnel lens blind area viewer design by eliminating the upward-looking section of the fresnel lens and adding a rear hood to reduce backlighting. How It Works The first generation blind area viewer was developed and in-mine tested as an aid to improved visibility for large haulage trucks. Other aids were improved left-and right-hand mirrors. Evaluations showed that a blind area viewer mounted on the right-front of the radiator deck was effective and was readily accepted by drivers. Nevertheless, because glare was a problem under certain conditions, a low-profile viewer was developed. Glare control louvers from the earlier design were kept and a backlighting glare control hood was added. The height of the hardware was reduced by eliminating the top three inches of the fresnel lens. This portion of the lens contained an upward-looking segment which originally was thought to be needed so the driver could see the horizon when he looked through the viewer and be better

Jan 1, 1982

Develop a method for control of groundwater inflow to chronically "wet" sections of underground coal mines, in order to reduce groundwater interference with mining activity and to minimize acid mine drainage. Approach In eastern coal regions, groundwater stored in fracture zones in the rock mass can create a significant water problem for underground mining operations. Fracture stored inflow to mine workings impedes mine productivity since storage water sources usually release at the active face, creating the poor mining conditions typical of a "wet" section. Fracture water can also contribute to AMD problems when the water subsequently contacts sulfide minerals in the coal, The Bureau of Mines has developed a mine-dewatering method that eliminates many of the problems associated with mine water inflow by draining these fracture zones before the water can reach the developing face and interfere with mining activity. How it Works The dewatering method removes large volumes of the stored groundwater through high-capacity pumping from a minimal number of wells placed strategically on fracture traces (the surface expressions of fractured rock zones). These fracture traces are located through low-level aerial photographic and geologic investigation. As shown on the map, dewatering wells are sited precisely on fracture trace intersections in order to take advantage of the increased pumping capacity gained from these zones of high permeability. Once well drawdown indicates that the stored water is depleted,

Jan 1, 1983

By R. N. Roby

"INTRODUCTION A preliminary examination of the Green Monster and Benich copper prospects was made by engineers E. W. Newnan and George N. Bennett, of the Bureau of Mines, on December 13, 1943. In an unpublished report, it was stated that certain geologic features appeared to be similar to those associated with the copper deposits of the nearby Butte district. On these premises, a preliminary diamond-drilling program was recommended to explore 300 to 400 feet below the mineralized outcrops for the possible presence of a sulfide enrichment zone. In accordance with that recommendation, three holes were drilled. This report presents the data provided by that preliminary drilling exploration.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell D. Moon, chief, conducts preliminary exminations, perform the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyses samples and performs beneficiation tests.The field work on the Bull Run exploration project was supervised byE. W. Newman engineer in charge of the Helena field office. The chemical analyses and assays included in this report were performed under the direction of A. C. Rice, acting engineer in charge, Bureau of Minos Rare and Precious Metals Experiment Station at Reno, Nev. The diamond-drill cores were logged by geologists of the Federal Geological Survey."

Mar 1, 1947

By H. H. Storch

Methane is the chief constituent of natural gas, and large quantities of it are also obtained in coke-oven gas and in the off-gases from cracking higher hydrocarbons. Perhaps the most important potential chemical use of methane is in the production of higher hydro- carbons, both aliphatic and aromatic. The results of a relatively large number of researches have been published in the technical and patent literature on the thermal decomposition of methane, the objective being an industrial process for the production of "antiknock" motor fuel. No industrially feasible process has, however, been developed. An inspection of the literature on this subject indicates that the chief difficulty in the way of accomplishing this object lies in controlling the decomposition so that undesirable products are eliminated. A considerable number of quantitative experiments have been reported, the results of which provide only a vague and confusing picture of the various steps in the thermal decomposition of methane. The reaction mechanism has not been subjected to rigorous fundamental study, and the necessity for such a study is obvious if further progress is to be made. The thermal decomposition is only one of the reactions of methane which are of potential industrial importance and which require further fundamental investigation. The oxidation, hydrolysis, and halogenation of methane are other reactions which must be studied further. In view of the importance of methane as a raw material for various industrially desirable products, it is appropriate that a survey be made of the important facts concerning the physical and chemical properties of methane which will serve as an aid in subsequent experi- mental work. No attempt will be made to present a complete chronological review, but rather a condensed critical description of the important literature will be presented.

Jan 1, 1932

By D. S. Colby, E. M. SEELEY

The total production capacity of the natural-gasoline industry increased to 27,212,000 gallons (647,905 barrels) daily on January 1, 1950, from 21,322,000 gallons (507,670 barrels) daily on January 1, 1948. The rate of growth during these 2 years averaged 13 percent per year, compared with 9 percent per year from 1946 to 1948 and 6 percent from 1944 to 1946. The total number of operable plants on January 1, 1950, was 554, 5 more than at the beginning of 1948. The number of absorption plants increased by 12, the number of cycling plants by 7, and the number of combination plants by 4. The number of compression plants and charcoal plants continued to decrease. Absorption plants accounted for 67 percent of the total capacity on January 1, 1950, compared with 62 percent 2 years previous. Eighty-two per- cent of the expansion in these 2 years was in absorption-plant capacity. Cycle plants accounted for 24 percent of the total industry capacity at the beginning of 1950, compared with 27 percent on January 1, 1948. The average daily capacity of absorption plants increased from 38,400 gallons at the beginning of 1948 to 50,600 gallons at the beginning of 1950. During the same period, the average daily capacity of cycle plants decreased from 150,200 gallons to 144,100 gallons. Texas showed the largest gain in number of plants 13 absorption, 4 compression, and 4 cycling plants. The State accounted for 67 percent of the gain in capacity and on January 1, 1950 had 50 percent total national capacity. Louisiana followed with 7 additional plants. Pennsylvania reported 14 and West Virginia reported 13 fewer plants than in 1948. Most of these reductions were in the number of compression plants.

Jul 1, 1950

By Jami M. Girard

INTRODUCTION Slope stability accidents are one of the leading causes of fatalities at U.S. surface mining operations. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to reduce the fatalities associated with slope failures and other unexpected failures of ground. The purpose of this paper is to introduce various warning signs of slope instability so operators are better able to recognize hazards. The most common slope monitoring equipment and practical methods of installation are discussed as well as the limitations of these systems. CONSEQUENCES OF SLOPE FAILURES Unexpected movement of ground causes the potential to endanger lives, demolish equipment, or destroy property. Between 1995 and 2001 (2nd quarter), 34 fatalities were caused by ground instability. This accounts for approximately 15% of all surface mine fatalities (Figure 1). These figures include fatalities classified by the Mine Safety and Health Administration (MSHA) as “fall of face or highwall,” “powered haulage,” “equipment,” and other MSHA accident categories, where the primary cause of the accident was unanticipated movement of the ground. This includes fatalities resulting from bench and highwall failures, rock falls, waste dump and stockpile failures, and the collapse of unknown underground workings. [ ]

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Haiti has been prepared from the best available information in Washington, but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Sep 1, 1930

By Steven J. Page, John A. Organiscak

Airborne dust generation is one of the byproducts of coal mining, processing, and handling. The amount of airborne total dust (ATD, respirable size and larger) and airborne respirable dust (ARD) generated is of primary interest for designing the level of engineering controls needed for adequate dust abatement. Laboratory crushing experiments were conducted in a wind tunnel with a roll crusher to identify relationships among crushing parameters, product size, coal rank properties, and airborne dust generation. Through the first series of experiments, the effect of primary and secondary breakage processes on both product size and airborne dust generation was examined. Through a second series of experiments, the effect of coal rank properties on product size and airborne dust generation was studied using a uniform crushing process with secondary breakage. Laboratory results indicate that secondary breakage of a particular coal notably increases the specific amount of ATD generated, while negligibly impacting the specific amount of ARD generated. A strong positive relationship was identified between the specific amounts of ATD and ARD generated during the primary breakage process (with minimal secondary breakage), but a negligible relationship was observed between the same two variables when secondary breakage was introduced into the crushing process. This indicates that most of the ATD and ARD is generated from the primary breakage, while secondary breakage has a more of an influence on generating additional amounts of larger sized ATD. Additional experiments involving the uniform crushing of eight different bituminous coals showed that the coal rank, expressed as the inherent moist fuel ratio (MFR = fixed carbon =(volatile x inherent moisture)), had diverse relationships between the product size created and the amount of airborne dust generated. As bituminous coal rank or MFR increased, the amount of coal product fines < 250 gm increased while the mass percentage of ATD and ARD liberated from these < 250 µm product fines decreased. Air dry loss (ADL) moisture in the coal was found to be inversely related to the dust cloud electrostatic field, influencing dust liberation from the coal product fines. Since the MFR was directly related to the dust cloud electrostatic field, opposite the ADL-electrostatic field relationship, the diverse relationships between the product size created and the amount of dust liberated from the < 250 µm product fines were explained. Finally, 12 to 14 times more ATD was generated as compared to the ARD generated during these experiments. These results should provide a fundamental basis for initial estimation of the airborne dust loading requirements of engineering control methods for coal crushing.

By L. C. IlsLey

The Bureau of Mines has collected field data and made laboratory investigations of trailing- cable performance in the hope of developing a better and safer cable for use with permissible mining machines . Because of their better insulation and performance , only rubber- sheathed cables were finally considered . The cables tested represented the product of six manufacturers . : After consideration of the results of the preliminary investigations , the conditions under which cables are used in mines , and the better performance of the later types of cables that were submitted as the investigation progressed , the bureau formulated a performance - test requirement and notified the cable manufacturers as follows : The hazards of the trailing cable are such that the bureau has been unable to extend beyond the machine its formal approval to cover the cable as at present developed . However , in the attempt to reduce the hazard as much as possible , cables passing certain tests will be recommended for this service and it is hoped that several cables will be developed to meet this requirement .

Sep 1, 1930

By E. C. Lane

"INTRODUCTION This is the fourth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36 3/. The second resort gave the same data for motor gasolines sold during the summer of 1936 4/. The third report of the series gave the same data for motor gasolines sold during the winter of 1936-37 5/.This report covers 63 brands of gasoline represented by 1,136 samples excluding the Pacific Coast. Those from the Pacific Coast were averaged by the Pacific Coast technical group before being submitted and are published exactly as they were submitted. In some areas reports were received from five or six companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others."

Dec 1, 1937