Search Documents

By C. B. Manula, R. L. Sanford, R. A. Rivell

A central requirement for using simulation models is the need for retrospect testing to validate experimental conclusions. Acceptance of a model by managers and safety practitioners is more likely to depend on its tested performance in-the field rather than on the underlying logic or the validity aspects of the model itself. It is here that simulation bridges the gap between theory and useful design procedures. The original version of the rail haulage sub-assembly was success¬fully tested in the field (Sanford, 1969). However, the case studies that were described here involved single-stage haulage and restricted jobtypes from UGMHS. Since this report together with Volume VI (Production Subsystem) describes extensive changes and modifications to the rail haulage sub-assembly and UGMHS, field tests were necessary to verify both the rail model and the linking concepts to the Produc¬tion Sub-system. Mine Description The candidate mine selected for model verification works the 6 1/2 foot Pittsburgh seam. Shaft openings are used for manways and ventilation and a dual compartment slope for materials handling. In the bottom half of the slope, a hoist with track handles supplies and equipment. In the upper half, a 42 inch belt conveyor travelling at 450 fpm moves coal from a rotary dump to the surface. The immediate roof is shale with the first 12 inches taken during development mining. About 4500 raw tons are produced daily from seven face units and one spare working three shifts. At seven of the sections,

Jan 1, 1974

By A. R. Rule

Research was conducted by the Bureau of Mines to develop a process for utilization of Idaho kyanite. A continuous gravity-flotation separation process was applied successfully to recover kyanite-group minerals from an Idaho ore containing about 21 percent combined kyanite, andalusite, and sillimanite. Dry magnetic separation of the concentrate resulted in a product containing about 90 percent kyanite at a recovery of 63 percent of the kyanite-group minerals in the ore, Alumina and silica analyses were within the range generally accepted for conversion to mullite, and the finished products had a pyrometric cone equivalent of more than 38. A recovered garnet coproduct may be of commercial value.

Jan 1, 1973

By D. G. Kesterke

Research was conducted to determine the feasibility of extracting elemental oxygen from silicate-bearing melts by high-temperature electrolysis. The method was based on a modification of existing processes for electrowinning metals from their oxides dissolved in molten halide systems. Electrolyses were performed at temperatures ranging from 1,050° to 1,250° C in boron nitride cells that incorporated a silicon carbide cathode and an iridium anode. The electrolytes contained volcanic scoria as the oxygen source, plus mixtures of BaF2 and LiF as fluxing agents. Cell gases containing almost 14 volume-percent oxygen were obtained. The average anode current efficiency for several experiments of extended duration was calculated to be 55 percent. Cell design and operating conditions are described, and some of the problems associated with the process are discussed.

Jan 1, 1971

By Roy H. Grau

Increased awareness of a healthy work environment is common to all industries and the stone industry is no exception. The presence of operating diesel equipment, welding, stone production blasting, and silica dust in a working environment all contribute to air quality issues in underground stone mines. Particularly recognized is the exposure of workers to diesel particulate matter (DPM). Recent regulations call for a DPM standard of 160TC ug/m3 (TC = Total Carbon). The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of these mines and consequently reduce the exposure of workers to harmful airborne contaminants. The results have shown that the ventilation of underground stone mines can be significantly enhanced using improved ventilation controls and techniques. Large-opening stone mines present specialized ventilation challenges because their entries are much larger than in other types of mines. Most stone mines have entries about 40 feet wide and up to 30 feet high, with bench areas that may extend even higher. These large entries present the positive opportunity to move large air quantities at relatively low mine fan pressures resulting in lower fan horsepower and reduced operating costs. However, the difficulty in ventilating large-opening mines is that even with large air volumes, the air velocity is often less than 100 feet/minute. Higher ventilation velocities more quickly dilute and remove contaminants from the face areas. Higher ventilation airflow velocities can be achieved by effective ventilation planning and proper choice of ventilation fans.

Jan 1, 2009

Reduce the hazards to which mine personnel are exposed by providing safer procedures for removing dragline wire rope terminations. Background The termination points of wire ropes used on draglines consist of a wedge and socket that lock the rope in place through friction. These components must be separated when the wire rope is changed. At present, the cannon method is the most common procedure used to accomplish this. However this method, using a small cannon and primer (detonator) cord to propel a steel projectile that will knock the wedge out of the socket, has the potential of causing injuries to mine personnel and damage to equipment. The Bureau of Mines, has devised safer, and equally efficient methods of removing wire rope terminations. The Bureau began by studying the cannon method, its merits and draw-backs. Safety guidelines were then developed for the cannon method, and two alternative methods-the pendulum ram and hydraulic pusher-were devised and tested. The Cannon Method The steel projectile used to separate the wedge and socket in the cannon method was found to be very effective. However, the method poses the inherent hazards of any explosive de-vice-hazards that could be increased by lax work procedures. There is no strict uniformity in the manufacture of the cannon or in the work procedures used in the mines employing it. Hazards could be reduced, or even eliminated, with adaption of certain manufacturing and work-procedure guidelines, such as 1) making the cannon and projectile de-signs, as well the work procedures used, uniform, 2) ensuring separate loading of the charge and detonator with insertion of the detonator through a separate port, 3) connecting electrical firing circuits only after the charge and projectile are loaded and the cannon is placed in its final firing position, 4) using approved detonating devices, 5) anchoring the cannon before firing and, 6) placing armor netting over the cannon before detonation.

Jan 1, 1986

By S. B. Levin

"INTRODUCTION An exposure of large beryl crystals in pegmatite on Beryl Mountain, in Sullivan County, N. H., was the basis for investigation by the Bureau of Mines to determine the extent of the beryl mineralization and to expose other parts of the same zone that were favorable for additional beryl-rich shoots. Testing by surface cuts, trenching, and tunneling was conducted by the Bureau of Mines from August to December 1943.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and makes beneficiation tests. The field work was supervised by Paul M. Tyler, regional engineer, and John D. Bardill, district engineer. S. B, Levin was in direct charge of the project.LOCATION AND ACCESSIBILITYThe deposit is on the northeast slope of Beryl Mountain, 1 mile south of the village of South Acworth. The village, on State Highways 101 and 123a, is 12 miles northeast of Bellows Falls, Vt. The deposit is reached from South Acworth over a gravel-surfaced road and about 1,000 feet of good truck trail (fig. 1).The nearest railroad siding is at Cold River, on the Boston & Maine Railroad, where there is also a fairly modern, but now idle, feldspar mill."

Mar 1, 1948

By Richard E. Dawes

Physical variables, a principal factor in the economies of mineral production, affect both capital and direct operating costs. By using a revenue-cost system for the framework, the analyses of revenue and cost categories demonstrate the relative importance of groups of physical variables, whether explicitly defined or not, to a lead-zinc mining operation. Physical variables affecting the producer represent about 60 percent of the total system influence as expressed by cost ranking. Other physical variables affect the remaining costs as controlled by the smelter, the transporter, and the landowner. Such resource conservation aspects as mineral losses due to mining method and mineral processing constitute a portion of the total revenue effects of physical variables. The physical variable revenue-cost system presented in this report offers a framework for cost-benefit analysis of mineral related research.

Jan 1, 1969

By Charles L. Kimbell

This study is intended to serve three roles. First, it represents a global overview and summary to supplement and complement the five regional companion volumes of the 1991 edition of the Minerals Yearbook International Review. In this regard, it also extends previous time series under this title that appeared as the introductory chapter to the international volume of the Minerals Yearbook from the inception of that volume in 1963 until it was subdivided into separate regional volumes in 1989. The basic statistical presentations herein generally contain data through and including that for 1991, although in a few instances the most recent statistics are those for earlier years because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting the world's mineral industry that have occurred between the end of 1991 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

Improve the safety, reliability and overall effectiveness of mine stench warning systems and to provide a means of remote control stench injector operation. Approach Industrial gas odorants were analyzed for their suitability for use in mine stench warning systems. A prototype stench injector capable of precise flowrate control was designed, fabricated, and tested using the odorant chosen as having the most favorable properties. Based on the results of the field tests, a second generation injector was developed. The second generation unit features optional remote control operation, and in addition, is simpler to refill and is less expensive than the original injector. A complete second generation system, consisting of two manually operated injectors and one remote controlled injector was in-mine tested through actual mine fire drills. How It Works Ethyl mercaptan mixed with Freon is the predominant stench agent used in the U.S. underground metal and nonmetal mines. However ethyl mercaptan's toxicity,

Jan 1, 1982

Provide optimum visibility of mining operations while maintaining protection and comfort for machine operators. Approach A cab with hydraulically powered variable-height control was developed and used on a loading machine in underground operations. How It Works The cab is attached to the vehicle on a horizontal trunnion located near the forward end of the cab. A hydraulic cylinder, controlled by the operator from inside the cab, pivots the cab about the trunnion providing variations of up to 16 inches in elevation. The nominal tramming position of the cab is with its underside 6 inches above the mine bottom. From this position the cab can be pivoted up, or down, so that its back end is elevated 10 inches, or lowered to the floor. (See Figure 1.) The cab encloses the operator for protection against both overhead and lateral obstructions, and it raises or lowers, allowing the operator to select the most advantageous cab height. The cab is angled inboard 30 degrees to the machine line of direction. The operator's seat swivels to allow view of the conveyor during loading. All controls are located within the cab and move up and down with it.

Jan 1, 1978

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX A - PNEUMATIC TRANSPORT OF FLY ASH 1. Introduction Two types of pneumatic transport of fly ash are critical to the success of (1) Transport of fly ash from the fly ash truck to the entrance to the borehole. Depending on the surface topography, this may be horizontal, decential and ascential. (2) Vertical downflow of fly ash through the borehole. All fly ash trucks have limited pressure with which they can pump the fly ash. Thus, the pressure drop in the fly ash hose will define the maximum length for pumping and consequently the maximum distance that the fly ash truck can be parked from the auxiliary blower. The same relationships describe the flow of the dilute fly ash-air mixture produced by mixing with the auxiliary air from the blower and thus define the selection of the pipe diameter. These are im¬portant considerations in the proper selection of the location of the passages to be sealed and the type of surface preparation required. The flow characteristics of fly ash down the borehole determine the selection of the minimum borehole diameter and the blower pressure. This appendix presents theoretical analyses of these flow regimes and summarizes the limited experimental data obtained during the field tests at Grant Town, described in Section 8.4. The analysis for the borehole flow is presented first as it is of greater interest to the program. This is followed by a discussion of the horizontal flow.

Jan 1, 1973

To recover metals as sulfide concentrates from contaminated waste streams using hydrogen sulfide (H2S) generated by the bacterial digestion of waste organic materials. Approach The goal of this research is to develop a treatment method for metal mine effluents that will rival the cost and convenience of conventional lime treatment, and that will provide better effluent water quality, result in less expensive sludge disposal, and allow for the selective recovery of metals.

Jan 1, 1993

Provide mine safety personnel, MSHA inspectors, and original-equipment manufacturers with guidelines and a check list for inspecting rollover protection structures (ROPS) being used in mining operations. The Problem ROPS are provided on mobile surface mining equipment to protect operators from such safety hazards as machine rollovers, falling objects, and collisions. However, the protective capability of a ROPS can be greatly reduced if it is damaged. Certain kinds of damage, such as hair- line cracks, corrosion, and loosened bolts, may occur as a result of normal machine use but may not be recognized as unsafe by untrained personnel. Therefore, the Bureau of Mmes designed a manual which can be used by mine personnel when inspecting ROPS equipment. The Manual The manual was prepared to help acquaint mine safety personnel and MSHA inspectors with typical ROPS deficiencies and their causes. It provides a systematic means for inspecting ROPS so that the identified deficiencies and their causes can be corrected. It is suggested that an inspection of the ROPS be conducted after every 1,000 h of equipment operation, or sooner if the structure has been subjected to any unusual loads which could cause damage, such as a rollover, highwall caving, or collision. The manual also details common deficiencies in the structure and attachment hardware which may affect the service life. The checklist, when used as instructed in the manual, provides a means for systematically inspecting the structure to ensure maximum protective capability and conformance with applicable Federal regulations.

Jan 1, 1986

By George J. Conroy, Angel G. Jordan, Eugene W. Bartel

Time-domain reflectometry has long been an accepted and used method for locating electrical faults in electrical cables. The process has, however, required the use of equipment that is somewhat complex and difficult to use. The skill level needed to operate such equipment is high. Therefore, the use of the time-domain reflectometry process has been limited to selected locations and controlled environments. The process, however, has great potential for mine system applications. The ability to locate and repair trailing power cable without removing it from the mine would result in great savings in cost and employee-hours. Therefore, an automatic microprocessor-controlled time- domain reflectometry system was developed to reduce process complexity and skill level needed to operate the unit. The theory of operations is discussed along with the computer analogies used in the unit. The present unit capabilities are presented and future areas of application and research are discussed.

Jan 1, 1979

By Kathleen Madland Kowalski

In recent years the issue of human stress response in emergency workers has begun to receive attention. This paper presents a rationale for considering human stress as a significant factor in the management of emergencies It discusses the concept of stress, Critical Incident Stress in emergency responders, and intro¬duces the Critical Incident Stress Debriefing (CISD) process. It is suggested that in a disaster, the CISD process can improve the effectiveness of response teams on site, their turnaround time on site, and post disaster time off the job. This paper, prepared by a US Bureau of Mines research psychologist, offers some ideas to the mining industry in general, mine rescue trainers and more universally, to those responsible for developing emergency management plans.

Aug 1, 1998

Avoid accidents that can occur when applying belt dressing from an aerosol can, particularly when can pressure has dropped or when spraying against wind. Approach Use a garde-type sprayer. How It Works Commercially available garden-type sprayers can be used for applying conveyor belt dressing from 12 feet away, or more. Pressure is easily raised and maintained at about 50 psi. Most sprayers have a hand pump, but a battery-powered cordless model is also available. Garden-type sprayers are available in various sizes from 11/2 to 18 gallons, with the larger models wheel mounted. The 3-gallon model evaluated by the Bureau has a shoulder carrying strap, which gives additional safety advantages. Use of the strap frees both hands for climbing ladders or holding onto catwalk rails. When spraying, one hand can remain on a handhold to lessen the chances of touching a moving belt.

Jan 1, 1980

By M. J. Ferrante

Low-temperature heat capacities and high-temperature enthalpies were determined calorimetrically for Na2Cr04, A reversible transition was found at 700° K with an isothermal heat of transition of 2,263 cal/mole. High-temperature X-ray diffraction analysis showed that the transition was a crystal change from the low-temperature orthorhombic form to the high-temperature hexagonal form. At 795° K the hexagonal form had the parameters a, = 5.691 and co = 7.478 A. Powder diffraction data for the high-temperature form are given and possible structures discussed. The melting point was determined to be 1,065° K with a heat of fusion of 5,810 cal/mole. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate enthalpies of formation, free energies of formation, and equilibrium constants of formation from 298° to 1,400° K. Equations that represent enthalpies above 298° K are given.

Jan 1, 1972

By Collin Stewart, Greg Hunt, Christopher Mark

Bowie Resources maintains one of the most pro-active ground control programs in the U.S. mining industry today. Its guiding philosophy is that everyone in the organization, from the miners at the face all the way through the top management, are involved in ground control. Some of the unique elements of the Bowie ground control program include: • Roof bolt operators log the stratigraphy of test holes in nearly every cut. These “lith-graphs” are used by section foremen to determine the need for additional roof support, and they are entered into the geologic data base for use in geologic modeling and mapping. • Underground core drilling is conducted to obtain data for CMRR and stability maps. • Weekly “Quality” meetings, involving mine management and technical staff, are held to ensure that ground control information is integrated into production operations. The paper will describe the program in detail, discussing the involvement of roof bolters, section foremen, surveyors, technical staff, and production managers. It will also show how the program has contributed to the mine planning process. Case histories of successful ground control interventions will be discussed.

By Verne E. Hooker

Stress relief measurements were made at three underground test sites associated with the Henderson project, American Metal Climax, located in the rugged, mountainous region between Loveland Pass and Berthoud Pass on the Continental Divide in Colorado. Sufficient data were obtained to determine the three-dimensional stress ellipsoid for each site. The measurements were made at hole depths greater than one diameter of the mined opening; thus, calculated stresses are representative of premining in situ conditions. The vertical components of stress are in good agreement with overburden depth including the influence of mountain topography. Horizontal components of stress substantially increase with depth. These components are believed to be influenced by stresses presumably of tectonic origin. The largest measured principal stress was 5,900 psi at a depth of 3.708 feet. The predominant orientation of maximum principal stress for the determinations at greatest depth is in the NW-SE quadrants.

Jan 1, 1972

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1962. Injury experience is measured by the number of injuries sustained per million man-hours of exposure in each industry. No attempt has been made to combine these data and present rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in volume III of the Minerals Yearbook. COAL The injury-frequency rate for the coal-mining industry of the United States increased less than 2 percent, according to reports received by the Bureau of Mines. The number of fatal and nonfatal injuries per million man-hours in 1962 was 45.86, based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1963