Search Documents

By E. H. Denny

The coal and metal mines of the United States furnish this country with a large part of the fuel and material necessary to support our industries and thus make possible the welfare and prosperity of our people and even the continuance of our present-day scale of civilization. Mining companies furnish material to industry with one general purpose in mind -- the making of a profit on their work. Efforts are being made successfully and continually to reduce operating costs, to increase production per man, and to perform work as far as possible mechanically and with more efficiency. These efforts are made primarily to reduce costs, to increase production, or to do both - in other words to make more profits or more certain profits. In the endeavor to reduce expense companies are considering more and more the factors which enter into costs of production, among them the factor of accidents and their cost. This paper endeavors to estimate the approximate cost of accidents to the mining industry in order to present the saving possible through accident reduction or elimination.

Jan 1, 1929

By W. D. Walker

All pipelines used to transport liquid fuels over coal mines are potentially hazardous; however, this publication deals only with dangers in transporting gasoline. Since transporting gasoline by this method is an established practice, the hazards connected therewith should he recognized by coal-mine operators and pipeline companies so that every known precaution may be used to reduce and keep the hazards to a minimum. The purpose of this paper is to direct the attention of coal-mine operators and employees, pipeline-company officials, and other interested persons to the explosion and fire hazards that arise from seepage of gasoline into underground mines. A hazard is not only presented in an individual mine when gasoline enters underground workings; but, in cases where mines are interconnected, a hazard exists in mach such mine.

Jan 1, 1954

By R. V. Ramani, C. B. Manula, A. Owili-Eger

MINE PROTOTYPE The prototype chosen for application demonstration is from Kingery (1960). The mine and the ventilation plan is presented in Figure 11. A new coal mine is projected with entrance by slope 1,500 feet long. Nine train entries will be standard for development, five as intake and four as return. One return shaft is planned near the slope bottom. The slope will have an area of 150 square feet and a perimeter of 55 feet. The return shaft will be circular with a diameter of 18 feet and will be 500 feet deep. Two hundred feet of the shaft and 500 feet of the slope will be concrete lined. Will it be possible to operate five units per shift with amount of air at each unit not less than 25,000 cfm? Additionally, a shop at the slope bottom will require 10,000 cfm. The problem is completely worked out using standard ventilation formulas and simple manual calculations in the above reference and is reproduced here in Appendix II for ready reference. APPLICATION In this manual, four different applications of the PSU/MVS are outlined. An article by Stefanko et al (1972), outlines how one can move from a mine map to a network for the generation of computer input. Attention is drawn to Figure 12, which is the network line diagram of the mine ventilation system in Figure 11. Note that every roadway junction has been numbered. The dotted lines represent leakage paths and the letter 'R' on a branch denotes that the split is regulated for the quantity shown. For example, there is a leakage

Jan 1, 1975

By J. B. Janus

This report continues a series of analyses of coal samples made by the Bureau of Mines in connection with the yearly purchase of several million tons of coal for various Government agencies. Listed are the analytical data on the composition and quality of tipple and de livered samples of coal collected during fiscal year 1974.

Jan 1, 1975

By J. T. McCartney

Thin sections of coal have been prepared for many years either by cutting on a microtome (1,2)5 or by grinding and polishing (2,1). Specimens of most coals had to be demineralized in hydrofluoric acid and softened in caustic solutions before they could be successfully cut with a conventional microtome. Some lignites could be cut without pretreatment. Jeffrey (1) obtained sections from coals of all ranks, although long and tedious pretreatment was required for anthracite. His sections were less than 1 cm.2 in area (probably much less for high rank coals) and about 5 microns thick. Thiessen (2) also cut sections of softened coals, mostly of low rank. His sections were a few square millimeters in area and about 3 microns thick. However, Thiessen preferred ground and polished sections for detailed studies because they were larger and had not been chemically attacked by softening media. He prepared ground sections as large as 4 cm.2 in area and usually 5 to 10 microns thick. Thousands of such sections, covering complete column samples of many coal beds, were studied for a number of years (4). With the development of the electron microscope and increased interest in quantitative optical studies of coals, a need for much thinner sections arose. However, no suitable technique for preparing such sections was known until Fernández-Morán developed a diamond knife for cutting ultrathin sections of hard materials (5). Workers at the Centre d'Etudes et Recherches de Charbonnages de France applied this new tool to the cutting of coal sections and have recently described their technique to the Burg, of Mines. Using their methods, with some modifications, researchers of the Bureau of Mines have succeeded in cutting ultrathin sections of coals ranging in rank from lignite to

Jan 1, 1961

By N. S. Dalal, X. Shi, V. Vallyathan

"INTRODUCTIONThis paper summarizes our recent investigations of the potential role of silicon-oxygen based free radical species in the biochemical mechanism of the lung injury caused by the inhalation of freshly fractured silica. The impetus for this study came from the following observations. Inhalation of crystalline silica is associated with the development of acute and chronic silicosis. Chronic silicosis is characterized by the development of sharply marked concentric fibrotic nodules in the lung. This occurs over a period of several decades with the development of progressive respiratory impairment. In contrast, acute silicosis is manifested by the filling of the alveoli with an amorphous lipoproteinaceous exudate within a short period after exposure, and rapid development of respiratory disability often leading to fatality. Most studies on the pathogenesis of silicosis have focused on the elucidation of cellular mechanisms of cell injury and the development of chronic silicosis. Because pulmonary responses to crystalline silica are distinctly different for · the acute and chronic silicosis, we hypothesized that the acute response is associated with some unique properties of ·freshly formed silica particle surfaces, due to the formation of some reactive chemical species caused by the rupturing or the silicon-oxygen bonds. In occupations involving drilling, tunneling and sandblasting operations acute silicosis can be correlated with this unique surface reactivity of silica. The formation or reactive species was demonstrated, using electron spin resonance (ESR) spectroscopy (Dalal et al., 1986; Fuibini et al., 1987; Hochstrasser and Antononi, 1972). Grinding of quartz crystals under ultra high vacuum (10-10 torr) leads to the formation of Si- and SiO• radicals and these radicals are quenched by exposure to air and other gases (Hochstrasser and Antonini, 1972). ESR signals have also been reported from micronized quartz samples that were evacuated at 413 K (Bolls et al., 1983). In order to find a more direct relationship of such radicals to acute silicosis, we made ESR measurements on quartz dusts freshly ground in ambient air and found- that indeed grinding under ambient environment leads to the formation of the Si• and SiO• type of radicals which decay on storing the dusts in air or in biological buffers (Dalai et al., 1986; Vallyathan et al., 1988). The Si• and SiO radical formation on grinding has also been reported by Fubini et al. (1987). In addition, we recently found that •OH radicals are generated in aqueous suspensions of freshly ground quartz (Dalai et al., 1988; Shi et al., 1988; Vallyathan et al., 1988). We have subsequently carried out detailed cytotoxicity and biological assays on freshly made as well as aged quartz dusts. As summarized below, the results provide new insight into the biochemical mechanism of acute silicosis."

Jan 1, 1988

By Robert A. Jankowski

Through laboratory and underground studies, the Bureau of Mines has evaluated the use of passive barriers (dust shields) to help confine dust generated by longwall shearers to the face area. Laboratory studies focused first on selection of the optimum barrier design, which proved to be a simple, gobside barrier (made of conveyor belting), coupled with a headgate splitter arm, which was found necessary to prevent the dust cloud from entering the walkway at the headgate end of the shearer when cutting tail to head. Further laboratory testing was done to determine whether using passive barriers in combination with different water-spray dust-reduction methods, including the shearer-clearer system developed by the Bureau, would improve dust reduction over that from using the water sprays alone. It was found that the combination of gobs ide passive barriers plus the full shearer-clearer system was most effective, and surmised that this would be especially useful in thicker seams. However, underground testing revealed that the shearer-clearer system alone was 35 pct more effective in reducing dust contamination than when used with the gobside passive barriers, and far more effective than using passive barriers with a conventional water spray system. For such an effective system as the shearer-clearer; the reduction in avail-able space over the top of the machine actually impeded system performance; this was shom1 in both eastern and western mines. But when used with comparatively inefficient water spray systems, the passive barriers, used in combination with a headgate splitter arm, provide consider-able help in reducing dust levels in the walkway.

Jan 1, 1986

By James L. Hendrix

A study was made of the United States Bureau of Mines' chlorine-oxygen leaching process for complex sulfide concentrates. The investigation sought to determine the kinetic order and IT mechanisms involved in the reactions betweens sphalerite, and galena with chlorine. The influence of copper on the extraction rates was also studied. It has been shown the rates of reaction of chlorine in aqueous solutions with sphalerite and galena are both zero order at 373K with the rate limiting step being the chemical reaction. Addition of cupric chloride increased the extractions of both lead and zinc.

Jan 1, 1980

By F. R. Cattoir, D. H. Baker

Fused - salt electrorefining has been successfully applied to the purification of vanadium metal . The electrolyte used in this refining technique was sodium chloride to which had been added 3 to 6 percent vanadium as vanadium dichloride . The average deposition current efficiency was 91 percent . Oxygen and nitrogen , the impurities in commercially produced vanadium metal , were reduced by two - thirds of the amount contained in the feed material . Hardness of the vanadium- metal product was reduced from an initial 97 Rockwell B ( RB ) to a minimum of 35 Rg . The reduction of these impurities markedly improved the plasticity of the final product obtained by melting the crystalline cell metal into small ingots . These ingots could be given a 99 - percent cold reduction by rolling before edge cracking appeared . Growing interest in high - purity vanadium and the industrial need for purer metals and improved alloys for use under high temperatures and high speeds have demanded the elimination and/or control of impurities . Accordingly, research to eliminate or control the undesirable impurities has been expanded .

Jul 1, 1960

By N. B. Greninger

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4-and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 2010

By D. Montagna

Large quantities of zinc-base die-cast scrap containing 3 to 4 percent aluminum are presently refined by mixing with other secondary zinc products such as galvanizer dross and distilling in a retort. The Bureau of Mines investigated alternate aluminum removal processes utilizing low-cost fluxes. Basing the investigation on the metallurgical principle that a reactive impurity can be removed from a less reactive matrix metal by melting under a flux consisting of a salt or oxide of a metal less reactive than the impurity, three separate flux mixtures were studied. In the first flux system, [FeCl3] + NaCI (the active component is underlined), part of the aluminum is' eliminated by the formation of volatile aluminum chloride and the rest by the creation of a high melting point iron-aluminum intermetallic compound that can be separated from the remaining molten zinc by filtration. Aluminum removal in the second system, [Fe203] + CaClz + NaCI, is effected by the formation of the iron-aluminum compound and possibly aluminum oxide. The third system, spent sal skimmings--essentially a mixture of [ZnCl2], NH4Cl, and ZnO, depends solely on aluminum chloride formation. Of the three flux systems investigated, the best results obtained were with system 3. Aluminum was reduced in the molten die-cast alloy from 4.10 percent to 0.01 percent when depleted sal skimmings were used.

Jan 1, 1969

By John M. Dower, Ralph W. Plummer, Terrence J. Stobbe, Hyunwook Kim

"The relationship between exposure to coal mine dust and the development of various respiratory diseases is well recognized. The cause of these diseases however. Is still uncertain. To study this cause-effect relationship, It Is necessary to characterize the coal mine dust In terms of the quantity of dust present and mineral content of the dust. Dust samples were collected using a Portable Continuous Aerosol Monitor (PCAM) and 4-stage cassette Impactors at various locations in an upper Freeport seam coal mine In West Virginia. The samples were analyzed using an X-ray microdiffraction film technique and energy dispersive scanning electron microscopy. This paper presents the results of the first phase of this characterization work which Includes determining the size distribution of the dust and the mineral content of the size intervals.IntroductionDiseases associated with dusts in coal mine environments continue to afflict miners in today's modem mines. These diseases still persist because, as Olishifski points out an employee rarely experiences exposures to a single environmental stress but rather to an Intricate Interplay of multiple stresses.(1) In the case of coal mining the multiple stresses are varying sizes of dust particles originating from coal imbedded minerals. Immediate roof strata bottom strata. Incombustible rock and the coal itself. The site of this Intricate Interplay Is the miner's lungs and the resulting diseases are a function of the composite dust exposures.The proper study of coal mine dust toxicity requires that the dusts used replicate existing coal and mineral dust compositions in their relevant size fractions. The purpose of this project is to develop the size and mineral content data necessary to support this ongoing toxicological effort.Existing coal mining standards and regulations also address total and respirable dust exposures. These dust terms refer to both the quality and quantity of the dust segment in the mine atmosphere. Dust quality addresses its coal and mineral content. whereas dust quantity Is described by mass per unit volume (mg/m3) The comprehensive characterization of coal mine dust exposures will enable revision of these standards and regulations to address the specific minerals and size fractions found to be toxic to human lung tissue."

Mar 1, 1989

By P. L. Loyselle, B. D. Comilsen, D. H. Carlson, J. H. Johnson

"In-mine airborne particulate samples have been successfully collected and the relative amounts of diesel and coal determined using the Laser Raman Quantitative Analysis (LRQA) method. This method allows analysis of filters which have been collected by a method similar to that used to determine the airborne respirable dust concentration in us underground coal mines. Samples were taken near the feeder-breaker, on haulage vehicles, and in the returns. Sampling methodologies were developed for coal-only and diesel-only particulate reference samples with sufficient filter loading for the LRQA method. A statistical analysis of reproducibility has been carried out. Samples have been collected simultaneously at two locations using the LRQA and the size-selective sampling methods. Good agreement between the two methods has been found.INTRODUCTIONThe goal of this research has been to develop the Laser Raman Quantitative Analysis (LRQA) method to measure the composition of respirable particulate, i.e. the fractions of coal and of diesel particulate, in the mine ambient air. In earlier Bureau of Mines sponsored research, we successfully demonstrated that the LRQA method could be used to measure the fraction of Diesel Particulate Matter (DPM) in coal/diesel particulate mixtures which were prepared in the laboratory.(I) 'The immediate objective was to test and refine this LRQA method on samples collected in a diesel underground coal mine.Specific objectives required to meet this goal include:I) Develop in-mine sample collection methods which will insure sufficient particulate loading on filters for LRQA. ,2) Develop methodology for in-mine collection of reference samples (""coal-only"" and ""diesel-only"" filters) which arc required for quantitative LRQA. 3) Analyze precision and accuracy of the LRQA method. 4) Compare composition measurements with another analytical method, i.e. the University of Minnesota/Bureau of Mines size selective sampling Micro-Orifice Uniform Deposit Impactor (MOUDI) method.An advantage of the LRQA method is that it allows analysis of filters which have been collected by a method similar to that used to determine the respirable dust concentration in US underground coal mines. No new sampling instruments and techniques are required. Transfer of sample from collection substrate to analysis substrate is not necessary. Furthermore, other analyses can be made on the same sample since the technique is nondestructive."

Jan 1, 1988

By R. Barany

The heat of formation at 298.15 ° K of muscovite was determined by solution calorimetry . The value obtained for the heat of formation from the elements was -1,421.2 ± 1.3 kcal / mole , and the value for the heat of formation from the oxides was -55.9 ± 1.3 kcal /mole .

Jan 1, 1964

By Byron. O. Pickard

"An Arizona mining company recently demonstrated a new use for the geophone by successfully locating leaks in compressed-air lines which were buried under from 1-1/2 to 2-1/2 feet of fine rock fill. The following information is abstracted from data sent to the Bureau of Mines by the superintendent of the mine.The company has two parallel main compressed-air lines, about one and one-half miles long, buried under an average of two feet of fine rock fill. One of the lines is a four-inch high-pressure (1000 pounds) main, and the other line a ten-inch low pressure (90 pounds) main. The two mains are separated by a 10 to 3C foot interval, and run from the compressor plant to the No. 2 shaft, where they are taken underground. A pump line is also buried in the immediate vicinity.Several leaks, not audible enough to be located, were developed in the Alms. Various =Abode were suggested that did not seem practicable to the management. Finally, the company obtained a Bureau of Mines' geophone and experimented with it. The first test& were conducted while the pumps were running, and while there was noise on the concrete pavement, all of Which caused so much vibration in the geophone that it was impossible to detect the leaks.The second attempt was made at the close of the day shift when the compressors were not operating and when the pumps could be shut down. The valves in the far end of the surface lines were closed, and the lines were pumped to full pressure (90 and 1,000 pounds respectively).Geophone readings were then taken at 7 or 8 foot intervals directly see the lines. Several leaks some very large in the high-pressure line were audible with the geophone at distances varying from 15 to 30 feet. A con-le leak in the low-pressure line was found at a distance of 10 feet. detecting the leaks, no difficulty was found in locating them exactly. ""At this time"", laid the superintendent of the mine, are unable to large a leak must be in order to be located under two feet of loose geophone. The fill we worked over was quite loose and dry and unfavorable for the work in question. However, we have no that the instrument is a valuable adjunct to our business""."

Aug 1, 1922

By G. J. Conroy

Cable whip occurring during normal movement of a shuttle car can result in a personnel hazard and excessive tensions in the cable. This Bureau of Mines report discusses preferred payout and reel-in torque settings to reduce cable whip. A simplified adjustment procedure is described.

Jan 1, 1974

By Jon C. Volkwein

The industrial sand industry has been exploring new techniques to reduce dust. One company was experimenting with adding water during bagging operations to the surface of the hag, and into the product as it flowed into the bag. The Bureau of Mines, using instantaneous dust sampling instruments, measured the effectiveness of three methods of adding water. Results indicated that various types of water sprays applied in carefully controlled amounts could reduce dust up to 50% at worker locations at the bagging machine and inside a railroad boxcar. This report also discusses constraints such as product handling, customer acceptance, cold weather problems, dust collector performance, and other areas.

Jan 1, 1981

By Nicholas G. Theofilos

Ecuador's real gross domestic product (GDP) increased 6% in 1976 despite persistent shortages of electrical power and essential fuels, which caused factory slow-downs and shutdowns. Petroleum export earnings, which made up more than 50% of total export value in 19716, totaled $565 million, a 9% increase over those of 1975. A new 60,000-barrel-per-day oil refinery at Esmeraldas was scheduled to go on- stream in mid- 1 97 7, operating entirely on Ecuadorean crude. Corpración Estatal Petró1era Ecualtoriana (CEPE) started construction of a 600-kilometer network of product pipelines which was scheduled to be completed in 1977 to coincide with the completion of the refinery.

Jan 1, 1980

Underground and strip mining (6,7) produce different hydrologic environments. Many underground mines are below the zone that is completely saturated with water and the mine openings may cause new and continuous contact between sulfurous material and water which flows from the saturated zone to the workings. Strip mines are usually above the zone of continuous saturation and contact between sulfurous material and water is generally restricted to periods of precipitation. A full appreciation of the problem of water pollution caused by drainage from deep mines requires a basic understanding of occurrences and movement of water in the ground and the modes of ground water entrance into mining areas.

Jan 1, 1970

By Dennis R. Dolinar

The danger to personnel, equipment, and pillar structure created by the spalling of a coal rib can be minimized by installing rib bolts. To assure that a configured support system will maintain a coal rib, the U.S. Bureau of Mines developed a rib bolt system based on a nonpreventable failure concept. A statistical equation quantitatively relates the amount of rib retained to the bolt spacing and the width of the spalled material. Laboratory test results show that the equation accurately predicts the amount of material retained and confirm the validity of the support concept. The examination of rib bolting at a coal mine experiencing rib sloughage provides evidence that the effectiveness of the support can be related to the failure pattern of the spalled material. An analysis of roof and roof support reaction to rib sloughage at the mine indicated that the rib sloughage had little effect on roof stability. Although supporting ribs might not affect roof stability, laboratory test results indicate that the material retained by the support can sustain a load up to 20 pct of the intact compressive strength of the material.

Jan 1, 2010