Search Documents

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958

By R. V. Ramani, R. Bhaskar

"One of the primary means of control of health hazards from respirable contaminants in mine atmospheres is through design and operation of mines to meet mine health and safety regulations and recommended practices. A U.S. National Academy of Sciences study concluded that for significant progress in coal mine dust control, research should be directed more toward obtaining fundamental understanding of the origin, transport and characteristics of respirable coal mine dust. Theoretical and experimental studies on transport of dust · in mine airways, particularly coordinated efforts to validate theory with practice, are scarce. Some empirical models, developed on the basis of experimental data, are available but these models cannot be applied to new conditions. The purpose of this paper is to present the results of theoretical and experimental studies on the transport and deposition of dust in mine airways. This study is a part of an ongoing research project in the Generic Mineral Technology Center on Respirable Dust.In the paper, the assumptions of the modeling phase of the project and the development of a convectiondiffusion equation for dust transport in mine airways are outlined. The important aspect of the modeling effort is the capture of the deposition phenomenon. The experiments performed under controlled conditions in a typical mine airway, as well as under normal mine operating conditions, are discussed. The comparison of the model predictions with experimental results are made to identify critical areas of agreements and deviations. The implications of the findings and areas for further research and development are presented."

Jan 1, 1990

By L. C. IlsLey

From time to time the Bureau of Mines has issued publications dealing with the various classes of explosion-proof mining machinery that have been tested and approved as permissible for use in mines having atmospheres that may become inflammable by reason of the inadvertent presence of gas or dust. These publications are confined almost entirely to description of the features contributing directly or indirectly to the prevention of explosion or shock hazards, and are intended to give inspectors, safety engineers, and others already familiar with the general safety requirements more detailed information on the safety features of the design of a particular machine. As a background for papers describing permissible machines and to avoid the necessity of duplicating descriptions of methods of conducting investigations and tests of such machinery, Bureau of Mines Bulletin 305, Inspection and Testing of Mine-Type Electrical Equipment for Permissibility, was published in 1929. Three bulletins giving detailed descriptions of the three most numerous types of machines have been issued, viz., Bulletin 313, Permissible Storage-Battery Locomotive and power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment.

Jan 1, 1937

Reduce longwall shearer operator's dust exposure by selecting the best drum water spray sys-tem for minimizing dust generated durinq cutting. Approach Three of the most commonly-used drum water spray systems were installed on the same set of shearer drums and compared to determine which system best suppresses dust. The spray systems studied were: ? pick-point flushing ? cavity filling ? water-through-the-it Instantaneous and gravimetric sampling instruments were used to measure the respirable dust exposures of the shearer operators and dust concentrations downwind of the shearer. The Three Systems: Longwall shearer drums are routinely equipped with internal drum spray systems since these systems have been shown to be more efficient than external systems in terms of dust suppression per gallon of water applied. All U.S. longwall shearer faces utilize some type of internal water delivery spray system. The two most common systems are bit-or pick-point flushing and cavity filling. Pick-point flushing uses nozzles mounted in the bit blocks or in special blocks immediately in front of the bits. Cavity filling utilizes spray nozzles installed in a pipe manifold mounted on the drum hub between the scrolls or along the edge of the vane scrolls; water is sprayed radially from the manifold towards the adjacent vane scroll.

Jan 1, 1986

By L. W. Higley

Procedures were developed for reclaiming high-temperature alloy scrap in the form of standard cobalt-base alloy. A cobalt-base, multicomponent, high- temperature alloy, such as S-816, can be successfully melted from scrap, and its specified chemical composition can be retained. Induction furnace melting in a controlled atmosphere was used to obtain ingots that were subsequently fabricated by impact forging to provide specimens for heat treatment and testing. Of the numerous metal elements in S-816 alloy, only small quantities of molybdenum were lost in the melting operation as finally developed. Test results indicated that the scrap material, after melting, forging, and heat treatment, was equivalent in room-temperature tensile strength, in high-temperature creep and stress-rupture properties, and in chemical composition to commercially produced S-816 alloy made from virgin material.

Jan 1, 1963

By J. H. East

The occurrence of hydrogen sulfide in the gas in solution in the oil produced from the Tensleep sandstone in the Elk Basin oil field in Wyoming constitutes a serious hazard to persons working in, that field. Aware of the general conditions because of petroleum reservoir studies being conducted in that field by its engineers, the Bureau of Mine's willingly agreed to a request of the Petroleum Administration for War to publicize the hazard and the measures for overcoming it. In October 1943 and November 1944, the Bureau of Mines investigated the method's used in handling the oil and in disposing of the hydro¬gen sulfide that occurs with it. This circular reports the results of these observations. HYDROGEN SULFIDE OCCURRENCE IN THE. ELK BASIN OIL FIELD The Elk Basin oil field is in Park County, Wyo., and Carbon County, Mont. It is about 18 miles north of Powell and 12 miles west of Frannie, Wyo. The original Elk Basin oil and gas field was situated in an eroded depression surrounded by an inner rimrock about 200 feet high with a bordering higher plateau about 500 feet above the basin floor.

Jan 1, 1945

By Seymour Wasserman

To develop noise control designs for secondary crushers in Taconite plants. Taken into consideration: 1. Acoustical criteria 2. Day-to-day operational considerations and maintenance accessibility 3. Materials of construction 4. Adaptability of design to other Taconite plants having crushers 5. Cost of noise control treatment.

Jan 1, 1977

By F. W. Benn

The Bureau of Mines investigated flotation methods for recovering fluorite and byproducts from two samples of the Fish Creek deposit in Eureka County, NV. The preferred method for tre.ating a fluorite-beryllium sample included (1) fluorite rougher and cleaner flotation, (2) desliming at 20 um, (3) muscovite flotation, (4) silicate flotation, (5) sodium hypochlorite wash of silicate concentrate, and (6) beryllium rougher and cleaner flotation from the silicate concen-trate. Laboratory results showed that over 94 pct of the fluorite was recovered in a recleaner concentrate containing 98 pct CaF2, Beryllium flotation produced concentrates containing in excess of 5 pct BeO with recoveries over 70 pet. The preferred method used for a fluorite-mica sample consisted of (1) fluorite rougher and cleaner flotation, (2) desliming at 20 um, and (3) mica flotation using an anionic-cationic collector system. Laboratory results showed that 84 pct of the fluorite was recovered in a recleaner concentrate containing 96 pct CaF2, Mica flotation produced a concentrate containing 95 pct mica at 85-pct recovery.

Jan 1, 1986

By Robert J. Hundhausen

This paper describes the methods and costs of sinking a 2-compartment shaft at the Hope mine, Clark Fork, Idaho. The Hope mine is owned by the Hope Silver-Lead Mines, Inc. Albert E. Nash, of Clark Fork, is president and manager.

Jan 1, 1948

By Oliver Bowles

From the most remote periods of civilization stone has been used to perpetuate the memory of individuals or to immortalize their noble achievements. Ancient memorials ranged from simple piles of stone (cairns), or single markers, to great obelisks and pyramids or magnificent mausoleums. The Taj Mahal at Agra, India, built of white marble by Shah Jehan in memory of the Empress Mumtaz Mahal, is one of the most beautiful and costly memorials ever built. It was erected between 1632 and 1650 at an estimated cost of $50,000,000 or more and is today an object of unusual interest for travelers. Other magnificent memorials both ancient and modern are to be found in many lands. No sharp line can be drawn between buildings and monuments, because the larger types of memorials such as the Bok Singing Tower, Lincoln and Jefferson Memorials, and mausoleums of various types have features in common with buildings. However, great care must be exercised in selecting a site for a quarry that will produce acceptable monumental stone because appearance as well as quality is of prime importance. The deposit must be of uniform texture and attractive color and must be notably free of knots, hairlines, impurities, incipient seams, or other defects. Many memorials are of polished stone, and spots or streaks that might be virtually Invisible on a natural rock face will appear distinctly on a polished surface. Hence, stone to be polished must be selected with unusual care. However, less flawless stone may be used for hammered surfaces.

Jan 1, 1955

By F. L. Wideman

SPURRED by demands of a buoyant economy for mineral products, output from mines in the United States established a new record. Removal of waste material, necessary for the extraction of economic minerals, kept pace with mine production. Earth moving by these two activities exceeded 3 billion tons, an increase of 5 percent over that of 1963. Crude materials from which metal or nonmetal products were derived accounted for 75 percent of the total. The remainder, mostly worthless, was classified as waste. Changes in the minerals industry result from many causes. Technological trends and labor productivity are among several significant and interrelated indexes that assist in the analysis of the changes. Therefore, a. study of productivity is helpful in measuring technological growth in mining. Concepts of productivity tend to vary with the purpose for which the term is used; frequently, productivity is expressed in terms of units of output per unit of labor, such as tons of ore per man-hour or man-shift. Comparisons of levels of productivity for a group of products are usually made using composites of output. Data for all metal and nonmetal mines except gold, silver, mercury, platinum metals group, and sand and grave were used to compile the composite for determining productivity for 1960-64. Copper ore, iron ore, and phosphate rock are mined mainly by surface methods, but characteristics of the deposits and differences in processing the crude material affect production of the commodities. Therefore, productivity data for these selected segments of the minerals industry reflect the influence of physical conditions on the exploitation of them.

Jan 1, 1965

By EINAR M. ARENTZEN

This information circular. deais primarily with an engineering descrip- tion of a type of longwall cutting and loading machine developed by Eick- hoff Maschinenfabrik, Bochum, Germany..: This machine is supposed to have been developed and tested during the latter part of 1941 and early 1942. The only source of information is con- tained in certain literature and engineering data, with drawings which were acquired by the Allied Military Authorities when Germany was occupied; and the information will have to be limited because the writer has not seen the machine in the factory or in operation. However, the information may be of interest to the coal-mining industry in this country, and for this reason our Government has decided to publish the data procured so far. The Eickhoff cutting and loading machine is particularly suitable for the longwall mining system. It can only be used under that type of mining system and is not suitable for the more common type known in this country as room-and-pillar work. The material for the description of the machine and its operation was compiled and translated from German drawings and operating instructions. These detailed drawings and instructions are on file with the Bureau of Mines and are available for inspection by any responsible person interested in the details of the construction of the machine.

Dec 1, 1946

By J. A. Herdlick

"INTRODUCTION The Bureau of Mines began a broad program of exploration of various proportion in the Pine Creek area of the Coeur d'Alene mining region in the fall of 1943. As a part of this project, exploring was done at theLittle Pittsburg property in 1945. The work included driving a 500-foot crosscut from the No, 6 level and drilling four diamond core drill holes to test the behavior of the Little Pittsburg vein at depth. This report presents the data obtained by the Bureau.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyses samples and performs beneficiation tests.The Bureau's exploration of the Little Pittsburg vein was one of the activities of the Albany Division of the Mining Branch, S. H. Lorain, chief. The project was started by R. M. Gammell, mining engineer, and was continued by the author and J. R. Reynolds, assistant mining engineer.The chemical analyses included in this report were made at Reno, Nov., under the direction of A.C, Rice, acting engineer in charge, Rare and Precious Metals Experiment Station, Bureau of Mines.The cooperation and assistance of the management of the Denver Development Co. is gratefully acknowledged, in particular that of C. E. Nugent, who made available much of the operational data included in this report."

Jan 1, 1947

By W. T. Benson

In May l942, the Bureau of Mines started exploring for manganese on the Black Poch manganese property, Esmeralda County, Nev., to determine possible reserves of manganese in the deposits. The work was done by the Bureau in cooperation with the Federal Geological Survey and comprised a study of the geology, mapping the area, and exploring by trenching, test pitting, and sampling. All ore bodies were examined and sampled, and the three most important areas were explored by trenching and test pitting. This report notes the location, ownership, and history of the deposits; explains the physical features of the district; mentions briefly mine workings and metallurgy; and describes the geology and ore bodies. The Bureau erected a temporary camp, repaired 5 miles of temporary road, constructed 1,000 feet of new road, dug 3,173 foot of trenches with a vertical crone section of 4 x 10 feet and 91 test pits with a cross section 3 x 6 feet, averaging about 6 feet deep, and cut 134 samples.

Jan 1, 1950

By Frank L. Gaddy

In this report, a description of mine practices, the preparation of roof bolts for laboratory experiments, the results of tensile-strength determinations, and a discussion of results of these tests are presented. Certain restrictions are recommended for roof bolts subjected to repeated bending, and two methods of complying with these limitations imposed by the restrictions are presented. The practice of bending steel roof bolts for installation in areas where the height of the opening was less than the length of the bolts required to support the immediate roof adequately has been adopted recently in several coal mines in lieu of sectional rods designed for that purpose. In addition, a few of these same mines have been reclaiming the bent rods and reusing them numerous times. The purpose of this study was to determine if these practices decreased the strength of such bolts and thus jeopardized the safety of the men working in these mines.

Jan 1, 1958

By Ben A. Kornhauser

Benin's industrial sector experienced severe economic and financial problems in 1986, including disappointing performances of the Onigbolo cement plant and the Semé Oilfield, plus a shortage of technically trained personnel and experienced management. Oil production remained about 1,000 barrels per day. Import and export trade between Benin and the United States remained minimal. Because much of Benin's outstanding external debt was in U.S. dollars, the stronger dollar greatly increased the debt burden. The 1985 budget of $304 million' was composed of an investment budget of $194 million and a current budget of $110 million. Of the investment budget, 84% was expected to be externally financed. About $45 million was given to three priority projects: the joint Benin-Togo Nangbeto hydroelectric project scheduled for completion in 1986; drilling of new exploratory wells of the Semé petroleum project, and the Dassa-Parakou highway. The budget deficit was projected to exceed $43 million despite a decrease in projected revenue owing to an anticipated decline of 25% in import tax revenue, normally the largest source of Government revenue.

Jan 1, 1987

By J. M. Stuve

Provisional values for the heat of formation of europium trichloride and europium sesquioxide were determined by solution calorimetry utilizing europium metal of more than 99-percent purity. The resulting values for the heats of formation of Eu203 (cubic) and EuCls (hexagonal) were -386,970 ±l,200 cal/mole and -218,740 ±650 cal/mole, respectively, measured at 298.15° K.

Jan 1, 1965

By F. E. Griffith

Cost data are given for five methods of secondary backfilling of strip mines previously partially backfilled. The operations were conducted in north-central Pennsylvania; an average of 600 linear feet of highwall were backfilled in each trial. Major obstacles and the relative merits of the methods are discussed.

Jan 1, 1966

By Jerry W. Ramsey

The Bureau of Mines studied two Pennsylvania anthracites using low-temperature carbon dioxide adsorption. A modified form of the Brunauer-Emmett-Teller equation was used to calculate specific surface areas. Two mesh sizes of each anthracite were used to determine how gamma irradiation at 106 and 108 rads, both in vacuum and in the presence of air, affected the carbon dioxide surface areas. Results show that anthracites have a system of pores that are essentially all interconnected rather than isolated; that anthracites differ from one another in specific surface, which may correlate with density; and that irradiation in vacuum has no discernible effect on specific surface of anthracite, but irradiation in air does produce changes in specific surface.

Jan 1, 1966

By L. C. IlsLey

"According to accident statistics, issued from time to time by the Department of the Interior, Bureau of Mines covering fatalities in coal mines, between the years 1870 and 1921 there were 4,897 deaths caused by explosives. The legislatures and safety commissions of the various mining States have Elected and formulated many excellent regulations in regard to the handling and use of explosives in an endeavor to keep this class of accidents as low as possible. An analysis or comparison of the explosive, regulations issued by over thirty States would make a very long paper, however, by subdividing according to phases and issuing several papers it is believed that the material will be more readily available. The first phase was treated in Serial No. 2405 of the Bureau of Mines (""State and Federal Electrical Shot-Firing Regulations,"" issued in October 1922) which gave a compilation of such regulations as apply strictly to electric shot-firing. The second phase under consideration is ""Who may set off blasts in coal mines.""In some States, the person who does the firing must be an ""authorized shotfirer,"" while in other States he must have proved his ability to do this work, and again in other States he is ""any person."" The present paper covers rules and regulations relating to this phase of shotfiring, and those States having similar regulations have been grouped as follows."

Jun 1, 1923