Search Documents

By Kung-Lee Wang

FOLLOWING the rapid recovery of previous years, the U.S. economy continued the upward trend and moved forward moderately and sporadically during the first half of 1962. There was a slow-down in the recovery rate, which was especially notable in the third quarter. The economy recovered in the fourth quarter, and by the end of 1962 the gross national product amounted to $555 billion, a new high, 7 percent above that of 1961. Production, employment, personal income, and corporate profits all achieved new peaks, but unemployment continued high and the prospects for improvement remained poor. The economy again failed to us~ its full potential; 1962 was a good year, but not good enough. During 1962, all industrial production climbed from the low in January to a high in late summer which lasted through the fall, and declined slightly at yearend. Mining production followed this pattern closely and most sectors were approaching record highs. Most minerals gained in value and volume of production. The steel-associated minerals group was the only exception, and it sustained a small net loss. The nonfuel minerals industry opened the year at a high level, maintained this high level until late summer, with the peak in May, and drifted downward toward the end of the year. The gains recorded by nonferrous metal mining partly offset the loss of ferrous metal mining, resulting in a small gain for metal mining as a whole. The upsurge of construction material minerals output was primarily responsible for the substantial increase in production of nonmetals other

Jan 1, 1963

By Thomas E. Marshall, Timothy Batchler, Anthony T. Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

By Alan G. Mayton

A prototype end-cab shuttle car (SC) design has been developed to improve protection and address ergonomic concerns of the SC operator in low coal mines. The new design features an end cab transversely mounted to the SC and equipped with a closed-circuit video system. The end cab was retrofitted to a low-coal SC and evaluated in surface trials at the U.S. Bureau of Mines. During surface trials, test operators evaluated the end-cab SC relative to visibility; cab features-space, seating, controls, and operator position; tramming-inby, outby, and turning corners; and dumping. Trials were conducted using 12 test subjects; 6 were experienced SC operators. Results of the trials were promising. Of the experienced operators, the only operator with low-coal experience gave the new design the highest rating. Four experienced operators rated the end-cab design "better" to "much better" than a standard center-driven, side-cab SC for visibility when tramming, protection from roof and rib hazards, and no change in seat position with direction of travel. This report discusses research to modify a used 21SC JOY SC, retrofit the SC with the Bureau-developed end-cab, and evaluate the retrofitted end-cab SC in surface trials.

Jan 1, 1993

By R. Hogg

"Particles play an important role in our environment and in many aspects of human activity. Much of the Earth's surface - sand, soil, rocks - consists of particles, as do clouds in the atmosphere, smoke from fires, and dust in our homes. Many of the foods we eat - cereals, flour, instant coffee - and everyday items such as pharmaceuticals, cosmetics, detergents and other cleaning products are encountered in the form of particles. Inks and paints consist of very fine particles dispersed in liquids. Modem agriculture uses huge quantities of fertilizers and pesticides, largely in particulate form. The list could be extended almost indefinitely; particle systems are obviously an important part of our daily lives. But what do we know about them? For most people, the answer is probably: not much.We are all familiar with the three common states of matter: gas, liquid and solid. In many respects, particle systems should be regarded as a distinct class of their own. The particles themselves may be solid but we all know that a heap of sand is quite different from a solid rock. A cloud of liquid droplets - fog - has much more in common with a cloud of solid particles - smoke - than it does with a bucket of water. There are certain characteristics and properties which are unique to the particulate state. The behavior of any particle system is determined not only by the material from which the particles are made, but also by interactions among the particles and with their environment. These interactions become increasingly important as the size of the particles decreases, and for exceedingly fine particles, smaller than about one micrometer (0.000001 meters or 0.00004 inches), these interactions dominate and we enter the realm of colloidal systems.Particle SystemsA system in which discrete entities - particles -are dispersed in a continuous medium can be regarded as a particulate system. The particles and the medium can consist of a solid, liquid or gas. The various combinations and some common examples are listed in Table 1. The properties and behavior of these systems depend on the characteristics of the particles, the nature of the medium, and the relative abundance of the two phases. In general, it is the latter which determines the kind of behavior exhibited by the system.As a general rule, the behavior of particle systems follows that of the dispersed phase (the particles) at high concentration, and that of the continuous phase (the medium) at low concentration. For example, both powders and smokes consist of solid particles in a gaseous medium. However, in a powder the solids typically occupy over one half of the total volume; in many respects powders behave like solids. In a smoke, on the other hand, the particles may take up only a few parts per million of volume, so that these systems generally behave like gases."

Jan 1, 1989

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

MFIRE is useful for the analysis of ventilation networks under thermal and mechanical influence MFIRE simu¬lates a mine&apos;s ventilation system and its response to altered ventilation parameters, external influences, and internal influences Extensive output enables detailed quantitative analysis of the effects of the proposed alteration on the ventilation system MFIRE was written in FORTRAN 77 and compiled with Microsoft° FORTRAN for the Intel 8086-8088 central processing units The source code is listed in appendix A for users who wish to modify the source code for operation on other computers MFIRE MODIFICATIONS OF MTU-BOM CODE The program described in Bureau of Mines Informa¬tion Circular 8901 has become known as the MTU-BOM codes MFIRE is an evolutionary product of the MTU¬BOM code with major improvements and enhancements 6 For users previously familiar with the MTU-BOM code, the following is a listing of the major improvements and enhancements incorporated by MFIRE 1 The length of an airway is an input value, LA The elevation difference of the airway is calculated from the elevation input, Z, in both programs It is possible for a data file to describe an airway that is shorter than its el¬evation difference The MTU-BOM code does not check for this error and uses the values of LA and Z This does not cause a computational problem, only a simulation problem MFIRE issues a warning message for this case, and the airway length is made equal to the elevation dif¬ference if LA is less than Z 2 To evaluate rock temperatures (average wall surface temperature of airway before a fire), it is assumed that the air temperature at an airway entrance is equal to the air temperature at the airway starting junction, and that the air temperature at the airway exit is equal to the air tem¬perature at the exit junction. The MTU-BOM code follows this assumption in all cases When a rock temperature of less than 0° F is calculated, an average temperature is used to represent the rock temperature of the airway MFIRE uses the same principle, except the consideration of unlikely rock temperatures When the exit junction of an airway is the atmosphere (a fixed condition junction), the air tempera¬ture at the exit is made equal to the air temperature at the airway beginning If an unlikely value of wall temperature (<0° F or > 150° F) results from calculations, a message is issued and the rock temperature is set equal to the air temperature at the airway exit The program user can always input rock temperature (TROCK) for an airway to override the calculated value. 3 MFIRE allows use of an optional reference airflow rate to define and limit the heat generation of a fire source This allows the simulation model to more closely resemble a real fire and to improve simulation conver¬gence Heat generation corresponds, but is not linearly related to airflow rates reaching the fire In the simula¬tion, heat generation is calculated from oxygen consump¬tion and is directly related to the variable incoming airflow Use of this optional reference airflow rate allows the heat generation to vary, but in a damped, user defined manner When the airflow rate passing through a fire source is equal to its reference airflow rate, the data items describ¬ing the fire source are not modified If the airflow rate is lower or higher than its reference airflow rate, the data items used to define the fire source are modified according to the following equations

Jan 1, 1990

By Andrew B. Cecala

This U.S. Bureau of Mines report provides a detailed description of the Bureau-designed modified shearer clearer system. Engineering drawings are provided for all major components of this system. The modified shearer clearer system is a revised version of the original system and is intended to improve the ventilation around both cutting drums. The original shearer clearer technique was solely a dust control technique that has been effective in lowering shearer operators&apos; dust exposures. The technique uses a series of water sprays that not only knock down a portion of the dust cloud but also act as small fans that move a substantial amount of air and keep the dust cloud from dispersing over the shearer body. The modified version is composed of two additional spray blocks for improved air movement around both cutting drums, thus lowering methane levels and the likelihood of an ignition. A laboratory study performed with the modified version in a full-scale longwall gallery resulted in a 73-pet reduction in methane concentrations at the shearer machine for both cut directions. The air-moving capabilities of the system provide more turbulence at the cutting drums and reduce methane levels.

Jan 1, 1994

By T. A. Klinefelter

"INTRODUCTION During the development work on sponge iron by the Bureau of lines it was desired to produce a product of maximum density for the furnace. One means of doing this would be to make a plastic mixture of the ground ore and extrude as pellets or large slugs or brick shapes.If a pelletizing Process is employed, the pellets must be strong enough to resist breaking when rolled and tumbled in going through the rotary kiln. If a brick-making process is employed, the brick must be strong enough to withstand handling and considerable pressure when stacked in the kilns.The study had two objectives: first, to find a binder of sufficient strength throughout the early stages of curing and heat treating and, second, to determine the degree of curing and heat treatment necessary to prevent disintegration under normal working conditions.Although the investigation had as its primary objective the processing of sponge iron, the data should interest other industries in which non plastic or poor-bonding slimes are a problem."

Jan 1, 1946

By Bertrand L. Johnson

Fertilizers are indispensable to national preparedness and defense. Production of adequate supplies of nourishing food for sustaining life in the United States is absolutely dependent in many parts of the country on the use of artificial fertilizers of various types. Only by using fertilizers can we maintain our present volume of production without great additional expense. Otherwise we would have to increase crop areas constantly to compensate for declining yields, we would have to lower the quality of food marketed, and standards of farm living and rural civilization would decline. About 60 million of the 360 million acres of crops grown annually in the United States Vow require fertilizing each year, and between 7 and 9 million tons of commercial fertilizers are consumed annually for this purpose.

Jan 1, 1941

By A. T. Iannacchione

Synopsis Underground stone mining Is an emerging sector of the U.S. mining industry. As this expansion takes mines under deeper cover, and as more efficient mining methods are utilized, effective stone pillar design methods will become even more Important. Current design practices are examined and a discussion of safe mine layouts is presented as a first approach towards weighing the demands for increased production against increased risk. Risks to underground stone-mine workers include rib Instabilities, pillar failures and roof falls. Seventy-two stone-mine pillar designs were examined. Pillars with width to height ratios of less than 1.5 appear more likely to fail when subjected to excessive stress levels. When width to height ratios fall below 1.0 defects in the pillars, such as through-running discon¬tinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties and orientation are also important determining factors in pillar strength. During the past three years the number of active underground stone mines in the U.S.A. has ranged between 90 and 100. This number is expected to increase as the crushed stone industry responds to growing demands for its products.1 As more of the industry moves to benefit from the advantages of underground mining production from underground stone mines is expected to increase above its current level of approximately 66 000 000 r/year. Parker2 identified four advantages of underground mining operations: (1) surface developments, zoning laws and environmental concerns are often less of an issue; (2) stripping and restoration requirements are eliminated; (3) additional reserves are often available beneath the quarry floor, under pit slopes or under an adjoining property; and (4) space is created for secondary use. Underground mines enjoy the added benefits of work in a constant underground climate, rather than in the variable surface climate, minimization of community concerns by placement of the crushing, sizing and stowing operations underground and reduction of surface vibration concerns through smaller blasts. The drawbacks of underground mining include added health and safety hazards for the stone miners, whose health can suffer from increased exposure to falls of ground, airborne contaminants and fog in large underground openings. Injuries from falls of ground in stone mines have occasionally exceeded the incidence rates for other mineral resources mined underground. 3 Existing underground stone operations, by comparison with stone operations a decade ago, mine more stone at a faster rate and with larger equipment. Because of high demand mines face increased pressure to yield more stone per production blast. A majority of the miners use the V-cut blasting pattern, which limits the depth or pull for each shot to about 4 m. Therefore, to produce more stone, either the mines must work more faces or existing faces must be enlarged. The enlargement of underground openings poses problems in the maintenance o€ strata stability, First, the widths of the mine entries partially control the amount of sag or deflection that any given roof beam can withstand before failure. This deflection can take pi ace quickly after an opening is excavated or much later as weathering processes form additional, thinner beams. Because increased deflection increases the potential for roof beam failure, there is a limit to how wide a room can safely be made. These limits depend on local geological and stress conditions and, to some extent, the cost effectiveness of roof-bolting. Given these room width limitations, underground stone mines have placed more attention on expansion of production through benching where mining thicknesses permit. The heights of rooms partially control the strength characteristics of adjacent pillars: as the room height increases for a given pillar width the pillar width-to-height ratio (w/h) decreases. In general, stone pillars are very strong, but when the width-to height ratio diminishes the potential for pillar rib instabilities and pillar failures increases (see Fig. 1). [ ] In the underground environment the desire to utilize wider rooms, higher benches and multi-level mining results in the potential for unstable ground conditions. Although the number of failed pillars is currently very low, the potential for additional failures will grow if more slender pillars are developed, especially under deeper cover, with wider mining sections and in multi-level operations. It should also be noted that the passage of time acts to decrease the strength of many existing pillars. An examination of current design practices

By P. W. Jeran, M. C. Irani, Maurice Deul

This Bureau of Mines survey of methane emissions indicates that total daily emissions have declined from 227 MM ft3 in 1971 to 214.7 MM ft3 in 1973. The highest average daily emissions in million cubic feet per day observed in U.S. bituminous coal mines were, in decreasing order, Monongalia County, W. Va. , 40.7 ; Marion County, W. Va. , 23.1 ; Buchanan County, Va. , 22.1; Washington County, Pa., 12.4; Greene County, Pa., 11.7; McDowell County, W. Va. , 11.4; Cambria County, Pa., 9.8; Jefferson County, Ala. , 9.5; Wyoming County, W. Va., 6.0; Marshall County, W. Va., 4.8; and Indiana County, Pa., 4.8.

Jan 1, 1973

By S. M. Runke

An ever-increasing demand for beryllium and beryllium alloys has directed attention to the milling of low-grade domestic deposits as a possible means of supplying part of the Nation&apos;s ore requirements. The United States generally produces less than 10 percent of its annual supply. For example, new supply in 1953 was estimated at about 9,250 tons, of which the United States imported 8,500 tons. Domestic production was only 750 tons.2/ Since record high prices for beryl in 1952 and 1953 did not greatly increase domestic product ion, the United States must develop mechanical beneficiation processes to use low-grade deposits and reduce dependence on foreign sources

Jan 1, 1954

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 6 Listing The following is a listing of the Mine Evacuation Simulation Program

Jan 1, 1976

By P. G. Barnard

The Nation&apos;s steel industry is largely dependent on shipments of manganese from foreign sources for steel production. An adequate substitute for the manganese requirements of our present steel technology would improve our national self-sufficiency and also contribute substantially to the conservation of our manganese resources. As each of these objectives is a major interest of the Bureau of Mines, possible substitutes for manganese in steel were investigated. Titanium was selected as the most promising substitute because the published results of several investigations indicate that titanium would perform the most obvious function of the manganese in steel: The elimination of iron sulfide and its deleterious effects. The investigation involved extending the published data on titanium additions in steel to provide enough information for an accurate evaluation of the practical value of the substitute. Therefore, quantitative data were obtained on the partition of sulfur and carbon between iron and relatively small titanium additions.

Jan 1, 1962

Estimate costs for projected uranium in-situ mining operations. Approach Develop a computer model and an associated data base which will allow users to supply data applicable to a specific mining site in order to estimate total capital and operating costs for a potential in-situ mining operation at the site. How the Model Works The model requires a minimal amount of input from the user. The data input must be known or estimated information about a potential in-situ mining operation. The user can also supply any additional project specifications. The computer model uses a process-engineering approach and determines through a discounted cash flow analysis the total capital and operating costs for the life of the project. This time-span measures from the start of the pilot-scale operation through to the site&apos;s restoration and reclamation. The model will determine the production cost per pound of material mined subject to the rate of return identified by the user. Conversely, it will also solve for the rate of return realized for the specific sales price per pound. [ ] Currently the model&apos;s data base can tai ns costs, rates, and specifications for Texas and Wyoming, the only states where commercial uranium in-situ mining is being conducted. However, this model can be used by anyone who is conducting in-situ leaching or who plans to leach uranium in-situ. At least part of any uranium deposit has a potential for in-situ mining.

Jan 1, 1982

By Robert M. Becker

A thick-wall cylinder solution applicable to the evaluation of anisotropic elastic parameters is derived for the interpretation of stress relief data. For a restricted class of problems, a special relationship among certain orthotropic moduli yields stress distributions for the plane orthotropic problem that are identical to the corresponding isotropic case. A ring or hollow cylinder with these specialized anisotropic properties subjected to uniform radial loads is one of the problems in this class. Consequently, known stress solutions are used to develop the strains and displacements for a specialized orthotropic thick-wall cylinder under uniform pressures. The results are consistent with anisotropic equations used in the evaluation of in situ rock stresses.

Jan 1, 1968

By Joseph P. Flick, Kathleen M. Kowalski, Lynn L. Rethi, Roberta A. Calhoun

Many miners are involved in tasks at the mine site that are similar to those sub-tasks performed in general construction, maintenance and repair (CMR) type work activities. As a result, many of the injuries in the mining industry today can be traced to employees performing these CMR type work activities. Indeed, a recent analysis of a major aggregate company revealed that 65% of all injuries documented originated from performing such CMR activities. It is hypothesized that the number of injuries to miners performing construction, maintenance and repair (CMR) work activities on mine property may be reduced through improved training that focuses on better hazard recognition using the numerous visual and other cues that are available for evaluating workplace health and safety hazards. To this end, researchers at NIOSH’s Pittsburgh Research Laboratory have merged two proven methods of training miners to recognize hazards, stereoscopic (3-D) slides and the concept of degraded images, into this training program. Stereoscopic (3-D) slides have been shown in earlier NIOSH and U.S. Bureau of Mines research to be an effective training aid for improving the ability of miners to recognize various geologic and mining-induced irregularities that can cause groundfalls.3 They realistically portray the natural mine environment, and thus are an excellent training aid for teaching miners to recognize such visual cues. The degraded image concept, originally developed by the military and used for target detection training, describes scenes where the target is partially hidden by cloud cover, dust, rain, natural barriers, buildings, or other obstructions that can camouflage or confuse the target. Research had shown that flight observers who were trained with less than ideal (or degraded) pictures were more successful in subsequent identification of targets than those trained using ideal (or highlighted) pictures of targets. In order to investigate this concept for training miners to recognize hazards, NIOSH researchers developed a prototype hazard recognition training program using such mining scenes. A control program based on traditional highlighted mining scenes was also developed. Both programs were applied to subjects in a field experiment. Results indicated that miners trained with the degraded images did significantly better on a follow-up test of hazard recognition.4 This hazard recognition program teaches trainees to look for hazards in a more realistic manner than that of the control program. This specific training program for CMR activities involves using the degraded image concept and 3-D slides. The module is designed to educate workers on hazard identification techniques and safe work practices. It focuses on teaching miners techniques for recognizing visual (sight) cues, and then uses these cues to evaluate mining conditions. It should be stressed that other senses, such as sound can also play an important role in hazard detection.

Jan 1, 1999

By Katherine Harding

This Bureau of Mines publication describes a practical approach to sampling that does not require elaborate statistical techniques. Simple steps are given for finding a cutoff point in the response from a repetitive survey. This procedure can be used to estimate the aggregate value of the characteristic being measured without waiting for a complete count from the survey. This is a useful technique when the reference periods are repeated at frequent intervals, such as monthly and quarterly, and when the statistical collecting agency is engaged in publishing timely data which must be accurate economic indicators.

Jan 1, 1971

By M. R. Geer, H. F. Yancey

"INTRODUCTION The increased use of coal as pulverized fuel has focused attention on the grindability of coal and on the necessity of evaluating this property by a method suitable for use in the usual coal-testing laboratory. Without some knowledge of how various coals behave in the grinding operation, that is, how their use affects mill capacity and power requirements, the selection of coals for pulverized-fuel plants cannot be made on the same critical basis used in selecting coals for other types of burning equipment. The grindability of a coal, serves principally as an indication of the mill capacity attainable in grinding it - not as a direct index of the total cost of grinding. Although the grindability of coal may play a minor role at some plants, it is a decidedly important factor where pulverizer capacity limits the ability to carry high loads.Purpose Standardized tests for determining the grindability of coal are relatively new, so that the information now available on the grindability of various coals is limited in comparison, for example, with that available on proximate analyses. Published information is restricted to determinations on many important Eastern coals by the Fuel Engineering Co. of New York, 4/ a bulletin giving the results of numerous tests by the Babcock and Wilcox Co. 5/, and a comprehensive report on. Alabama coals by the Bureau of Mines. 6/This report presents the results of grindability tests of 34 samples of coals from Illinois, Kentucky, Pennsylvania, Utah, Virginia, Washington, West Virginia, and British Columbia at the Northwest Experiment Station of the Bureau of Mines, Seattle, Wash., in cooperation with the College of Mines of the University of Washington. In the future, as the laboratories of the Bureau make grindalility tests of other coals, additional reports will be issued."

Jul 1, 1938

This Volume documents the Phase 111 effort on the Seismic Detection and Location of Isolated Miners on Contract H0122026 undertaken during the fall of 1972 by a task team composed of ADL staff and several seismic consultants. The team was assembled specifically to work together on complementary tasks, at an accelerated level of effort for four months, to meet the Bureau of Mines&apos; time schedule for obtaining independent, objective, technical judgments regarding seismic methods and systems for detecting and locating isolated miners. The impetus for this work resulted from a compilation and analysis, during the first half of 1972, of new experimental data obtained from a series of in-mine field tests conducted by Westinghouse Corp .+ using the CMRSS* interim seismic location system. The Bureau of Mines took advantage of the availability of these new data to reassess the potential and limitations of various seismic methods and systems, and to direct its seismic system improvement program accordingly. ADL assisted the Bureau in this reassessment by drawing on the skills of seismic consultants from industry, universities and government, to supplement the skills of the ADL project team. The consultants were principal resources of broadly-based and detailed technical expertise in the areas of seismic signal-source and signal-propagation characteristics, natural and cultural seismic noise, seismic sensors and field instrumentation, seismic signal and data processing for detection and location, and overall seismic system utilization in the field under operational emergency conditions. Specifically, the participating consultants were: F. Crowley, Air Force Cambridge Research Laboratories ; W. Dean, Teledyne Geotech, Alexandria Laboratories; R. Greenfield, Pennsylvania State University; J. Kuo, Columbia University; D. Peters and R. Crosson, University of Washington; and F. Pilotte, U.S. VELA Seismological Center. The principal ADL participants were J. Ginty, R. Lagace, M. Roetter, and R. Spencer.

Jan 1, 1974

By Peter Kovalchik, Ed Kwait, T. Michael Durr

1. BACKGROUND Many research projects on engineering controls for noise reduction in mining were conducted by the former U.S. Bureau of Mines, mostly under contracts from 1972 through 1986.1 Contracts were awarded to determine which mining equipment was responsible for worker noise exposure over the permitted Federal Regulation level of 90 dBA for 8 hours. Dominate noise sources, for each piece of equipment was also determined. The final goal was to develop engineering noise controls for those pieces of equipment and then evaluate them. This was the general approach taken in each research project or contract. This paper deals with what is known about the control of noise from continuous miners, one of the most commonly used underground mining machines. A literature review on continuous miners revealed that the relevant noise sources were divided into four categories: conveyor, cutting head, drive train, and motor noise. The dominate noise sources reported were the conveyor noise and the cutting noise.2 Conveyor noise consists of impacts and scraping at various locations on the conveyor structure. These impacts are associated with discontinuities on the top and bottom decks, impacts between the chain and the tail roller, impacts on the sidewalls at path points of discontinuity under horizontal pivot, and impacts on the flex plate.3 Scraping occurs along the entire length of the chain conveyor. The other dominate source, the cutting of coal, has also been addressed in past research.4, 5, 6 The research presented in this paper only addresses the controls associated with the conveyor. The literature suggests several effective treatments for noise control: retrofitting the chain conveyor with a urethane coating or a urethane sleeve on the chain flights, using a urethane coating or urethane sleeve on the tail roller, constrained layer damping of the decks, and the use of a modified take up plate.7, 8 However, the in-mine durability of these concepts has yet to be proven for the conveyor system. This paper analyzes extensive noise and urethane durability testing on a Joy 14CM9 continuous miner’s conveyor assembly, tail roller, and bottom plate conducted at the Pittsburgh Research Lab facilities. It will also discuss the initial underground testing results for the urethane-coated conveyor flights and tail roller.