Search Documents

By K. K. Kelley

"In an earlier consideration of the vapor pressure of iron 3/ it was found necessary to estimate the specific heat of gaseous iron to write satisfactory free-energy-of-vaporization equations for the several forms of iron. That the specific heat of gaseous iron will exceed greatly the classical value of Cp = 4.967 calories per gram-mole per degree is evident from even a cursory Lamination of its spectrum. The two lowest energy states are separated by only 416 cm-1, which is small enough so that the second state is effective, theoretically, at below room temperature. Such phenomena are by no means uncommon, but, while they have been recognized with substances that ordinarily are encountered as gases, classical gaseous specific--heat values still are used, often without question, for the vapors of metals and other elements that are solids under ordinary conditions. The following calculations for iron and copper gases are presented to illustrate the sort of deviations from classical values that are encountered with metal gases.The methods employed in calculating from spectroscopic data of thermodynamic quantities such as specific heat, entropy, and free energy have been described, in detail by Giauque 4/ and others. These will be briefly reviewed here. It is customary to separate the translational energy of a molecule from the rotational, vibrational, and electronic energies. In the case of monatomic gases, only translational and electronic Energies are involved. The classical expression for the specific heat of a mona¬tomic gas, Cp = 4.967, deals only with energy stored in the molecule as translational energy and consequently is valid only in temperature ranges in which no appreciable number of molecules undergoes a change in electronic state."

May 1, 1937

1. PURPOSE The Temporary Face Support System (TFSS) consisting of beams, posts and carrying-emplacing equipment was developed to provide temporary supports between the working face and the permanent roof supports. 2. GENERAL DESCRIPTION The system consists of: ? A Beam And Post Carrier And Deployer (BAPCAD), a self-propelled machine that carries as well as emplaces the beam-and-post sets. ? Lightweight mechanically self-deploying posts designed to safely support a load of 10,000 pounds each. ? Lightweight constant strength beams (bars) capable of sustaining an approximate equally distributed load of 8500 pounds. Note. All referenced figures and drawings are found at the back of this manual.

Jan 1, 1980

By S. J. Gasior

Pilot plant studies showed the technical feasibility of fluidized-bed operation for producing hydrogen and synthesis gas by the steam-iron process. A mixture of iron and iron oxide from 20-to 100-mesh was partially reduced with a simulated producer gas and then oxidized with steam and/or carbon dioxide. Results of tests show the effects of pressure, temperature, bed height, gas-to-solids ratio, type of iron oxide, and composition of gas on the gas and solids conversions during reduction and oxidation. A baffled free-fall solids system was also found operable. The short residence time of about 5 seconds limited conversion of the solids.

Jan 1, 1961

To develop a simple device for rapidly determining the shearing strength and angle of Internal friction of coal and rock in situ. Approach Use a portable, permissible, hydraulically operated device in boreholes as deep as 100 feet into the rib, floor, or roof of the mine. How it Works The device, called a Borehole Shear Strength Tester (BST), is inserted Into a 3-inch-diameter borehole to the desired depth, locked Into position, and activated to shear the rock or coal in the borehole walls. The normal and shear pressures exerted by the BST, which are recorded during the test, are used to calculate the shearing strength and the angle of internal friction. The BST consists of 3 main components and several minor components. Main components are: ? A shear head with 2 shear plates that bite into the rock when normal pressure is applied. ? A hollow hydraulic jack with RW drill rods that pull the shear head when shear pressure is applied. ? A console with a hand pump and two hydraulic gages to activate the device and to indicate the pressures that apply the normal and shear faces to the shearing plates.

Jan 1, 1981

By E. D. Calvert

As part of its goal to minimize the requirements for critical and strategic minerals, the Bureau of Mines is conducting research to foster the use of domestically abundant materials such as molybdenum. This report describes the development of an investment shell molding technique that can be used to make castings of molybdenum and its alloys. The mold material is cubic Zr02 with a monoclinic Zr02 binder. The shell, formed by standard investment molding techniques described in the text, is prepared for molybdenum casting by firing for 6 hours at 1,550° C (2,822° F) or for 4 hours at 1,650° C (3,002° F). The resulting castings have predictable and reproducible dimensions with good detail. As-cast strength is poorer than the strength of wrought materials below 1,600° F. At and above this temperature, tensile strengths of cast and wrought materials are nearly equal. Aqueous corrosion of the castings in most media is insignificant.

Jan 1, 1982

By John Jordan, Steven J. Knoll, Douglas Tesarik, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

By Richard E. Ray, George N. Aul, Fred Garcia, William P. Diamond

Increasing longwall panel dimensions, particularly face width in gassy coalbeds, may result in unexpected increases in methane emissions. To investigate this problem, continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). It was predicted by regression analysis of methane emissions data from 229 m (750 ft) wide longwall faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7 percent (0.6 m3/min (20 cfm)), to 8.6 m3/min (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces at the VP-3 Mine could increase methane emissions by as much as 13 percent (1.8 m3/min (65 cfm)) to 16.1 m3/min (567 cfm). The geologic and mine design factors influencing the variation in face emissions between the two mines will be discussed.

Provide a lighter, smaller apparatus for more gently supporting electrical cable as it is raised or lowered in a well as compared with the conventional method of using a winch and pulley. Approach The conventional method of running cable into a well is to use a winch to pull the cable over a pulley located at the end of a boom placed over the well. This has the disadvantages of being bulky and of placing a concentrated strain on the cable at the point where it moves over the pulley. These disadvantages are overcome by using a "Chinese finger" cable grip assembly to hold and release a multiple conductor cable.

Jan 1, 1986

Provide longwall operators with practical information and guidelines concerning mine design to reduce problems associated with the interaction of adjacent workings in multiple-scam longwall mines. Background The high productivity achieved by longwall mining demonstrates its potential to provide a substantial segment of underground coal production. Longwall mines produce more than 30 pct of underground coal, up from pct just 15 years ago. However, the continued growth of this mining method without appropriate multiple-seam planning may increase the cost and risk of mining. Research by the U.S. Bureau of Mines (USBM) indicates that 25 longwall mines (32 pct of the total number in the United States) have mining in adjacent coalbeds either above or below. About half of these longwall mines report some type of interaction problem with the adjacent workings, such as caving due to subsidence. Optimization of mine design factors is the best means for controlling interactions between operations in adjacent scams. To avoid higher mining costs, operators should focus on adopting practices and procedures that prevent and control interactions in multiple scams. The USBM, in an effort to improve longwall mine planning, has been investigating multiple-seam longwall design and development.

Jan 1, 1994

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Computer input data for an operating mine is developed on the basis of a detailed ventilation survey which includes air quantity, air quality, pressure loss and fan performance measurements. Quantity measurements must be reviewed extensively and assumptions made about leakage quantities and airflow paths. Pressure measurements must be reviewed and developed into a pressure gradient for the mine system. Air quality measurements are used to determine methane sources and amounts. Finally, the fan test data is used to develop the correct fan characteristic curve. Quantities and pressure losses for each branch in the system are used to calculate the branch resistances which are then utilized in the ventilation simulator to model the mine system. QUANTITY BALANCE The quantity of air coming into a mine based on field measurements will rarely equal the quantity exiting the mine, even if allowances are made for methane or compressed air input to the system. The same statement can be made for airflow through any isolated part of the mine ventilation system such as individual working section or main aircourses leading to an area isolated from the rest of the mine. The reason for the apparent discrepancies is the accuracy of the indicated quantities which in turn is based on the accuracy of the individual velocity and area measurements. Even with measurements following the guidelines described in the previous section on quantity measurement, this error can only be minimized but not eliminated. As a result the ventilation system must be carefully balanced so that, for any loop, the quantity in plus any methane or compressed air injection will equal the quantity out. The continuity of flow described by the balanced system must approximate the

Jan 1, 1977

By John P. Gooch

Data for the ternary phase diagram for the system 1,1,2,2-tetrabromoethane/water/2-propanol at 25° C have been measured. Experimental methods used are described, and the complete ternary phase diagram is presented. A simple example is given to review the use of the ternary diagram.

Jan 1, 1972

By Richard J. Kline

This publication comprises tables listing friction loss for a flexible, spiral-reinforced circular ventilation tubing system. The tables were constructed with the following parameters: a friction factor of 62 X 10-10, 10-foot sections of tubing ranging in total length from 100 to 550 feet, air quantities ranging from 1,000 to 15,000 cfm, and one to four 90° bends in the tubing. The aim of this publication is to improve ventilation tubing analysis and to provide a method of proper fan selection.

Jan 1, 1971

By R. V. Lundquist

The work described in this report, part of the Bureau of Mines long-range program to develop methods of utilizing submarginal domestic sources of aluminum, was undertaken to investigate the effects of iron in the lime soda sinter process, The approximate Fe2O3 content in a sinter for maximum alumina and soda recovery was 8 to 9 percent. Fe2O3 appears to inhibit gelation, and 15.5 percent Fe2O3 produces effects similar to those produced by 1 percent sucrose. In the lime soda sinter process, aluminum silicates are sintered with limestone and soda ash to yield dicalcium silicate and sodium aluminate. The sodium aluminate is extracted by leaching in caustic solution. The solution is purified by heating in an autoclave with lime to remove silica, and alumina trihydrate is precipitated with carbon dioxide. The reactions involved in sintering and leaching are complex. A number of studies by the Bureau of Mines4-9 and others1 indicate that the iron content of sinters influenced the recovery of alumina and soda and the gelation characteristics.

Jan 1, 1962

By Donald F. Reed

In its investigation of old, abandoned, lead-zinc mines at which records of operations are not available, in 1914 the Bureau of Mines dug surface trenches anti', in 1947 It diamond-drilled three holes at the Albright Farm deposit in Sinking Valley. Some good lead-zinc ore had been extracted from veins in dolomitic limestone during the time of the American Revolution and as late as 1870. Since that time the only activity was sporadic prospecting and developing. Thu Bureau of Mines disclosed two additional veins by surface trenching, but diamond drilling failed to find significant lead-zinc mineralization.

Jan 1, 1949

By W. W. Adams

luring the past two years the Bureau of ?,lines has been receiving from 100 to 150 coal mines in various States a report of each accident causing death, permanent total disability, permanent partial disability, or temporary disability lasting beyond the remainder of the day or shift on which the accident occurred. For each 100 accidents in these groups, there are perhaps from 35 to 45 accidents that do not disable the employee beyond the remainder of the day, and of these fraction-of-a-day accidents the Bureau has compiled no statistics. Information revealed by the reports is to the effect that falls of roof and coal in bituminous coal mines are responsible for 28 per cent of the temporary injuries to underground workers and 33 per cent of the days lost from all temporary injuries underground; they also indicate that falls caused 59 per cent of the deaths from all causes underground. Figures compiled by R. N. Hosler, of the Pennsylvania. Mine Rating Bureau, and covering accidents in bituminous; minis in that State, chow that 61 per cent of the deaths underground during the years 1917-1921 wore due to falls. Neither of these percentage figures includes deaths in major explosions; figures for all bituminous mines in the United States during the five years 1920-1024, inclusive of deaths in major explosions, show that 52 per cent of the deaths underground and in shafts were due to falls of roof and coal.

Jan 1, 1925

By V. E. Erwin, W. W. Adams

"INTRODUCTION This report presents statistics of accidents at coke ovens in the United States during the calendar years as 1933, the twenty-first year for which data of this kind are available, 1913 being the first year for which accident reports were collected from the operating companies by the Bureau of Mines. The present report is presented in mimeograph form because insufficient funds are available for printing it. The first report of the Bureau of Mines that contained statistics of accidents for the coke-mining industry in the United States covered the two calendar years, 1913 and 1914. While the figures presented therein related both to beehive and by-product ovens, the original returns from the operating companies were not classified so as to permit the presentation of accident statistics for each class of ovens separately. Beginning with 1915, the accident reports from the operating companies have shown the general type of ovens to which the reports related; therefore, since that year, separate statistics for each of the two classes of ovens have been given in the Bureau's yearly reports of accidents at coke ovens.The coke-making industry in the United States established a safety record in 1933 almost equal in merit to that which it achieved in 1932, when the accident-frequency rate was the lowest and therefore the most favorable that the industry has known. Credit for the achievement is due almost entirely to companies operating byproduct ovens. (See table 8.)"

Mar 1, 1935

By Wilbur I. Duvall

The Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole whose boundary is subjected to applied shear loads over four separated arcs. The results for the applied shear loads can be superimposed on the results for applied radial loads, given in a previous publication, to obtain a complete two-dimensional approximation of the stresses and displacements induced in the rock by tunnel boring machines anchored in a circular tunnel by means of four props. Analysis of the various solutions shows that the tangential tensile stresses induced on the boundary of the circular tunnel by applied radial loads can be minimized in the roof and floor of the tunnel by the application of appropriate shear loads to each of the four props. Thus when planning tunnel boring operations, consideration should be given to the in situ stress field in the rock and the induced stresses in the rock resulting from the applied radial and shear loads produced by the props of the boring machine.

Jan 1, 1968

By R. J. Hundhausen

The Takilma-Waldo copper district in Josephine County, Oreg., was studied by the Bureau of Mines from September 1950 to April 1.951 and from December 1953 to April 1954. Funds for the investigation were provided by the Bureau of Mines and the California-Oregon Power Co., Medford, Oreg., on a cooperative basis. The copper mines in the district are credited with a total production of ore worth $1,700,000. Since 1933 the mines have been unproductive and, except for minor exploration, largely inactive. The history of the district indicates that the copper deposits were mined principally during periods of high metal prices.

Jan 1, 1956

Determine whether the total delay time in blasting may be safely increased beyond the currently permitted 0.5 s, without igniting a methane or methane-coal dust atmosphere and determine the minimum borehole spacing to avoid misfires. Approach At present, regulations limit the delay time used in short-delay blasting to a total of 0.5 s. Many in industry and government would like to see this total delay time increased to 1 5 to permit an increase in the number of different delays available for short delay blasting and an increase in the time between delay periods. The Bureau of Mines conducted research to determine whether the total elapsed delay time for blasting coal in underground mines could be safely expanded, with resulting improvements in productivity. The research was conducted at a surface mine in St. Clairsville, Ohio. Experimental shots were conducted in several pits, each of which had a 5-foot-high coal seam (Pitts-burg No.8) in a 50-foot highwall. The coal seam and a mobile gallery provided a good simulation of an underground coal face. The Bureau also examined the relationship between borehole spacing and misfires, to check on reports over the past few years that permissible explosives frequently misfire. These reports were not well documented, but were numerous enough to warrant investigation. Misfires of permissible explosives in an underground coal mine can be very hazardous; a burning cartridge of explosive may be ejected from a borehole and ignite the gas or dust in the mine, or a misfired cartridge in the muck pile may detonate during drilling and mucking operations, causing serious injuries.

Jan 1, 1986

By Robert M. Becker

A multistage probability model for assessing the reliability of mineral samples following any number of stages of sample reduction is presented. Sample reduction is the process of alternately crushing or grinding and sampling mineral particles prior to assaying. The final multistage model developed accurately describes the ideal sample reduction practice. This model is based on previously developed and experimentally tested models for a single stage of sampling. The problem is approached through the probability distributions for the various stages of sampling. The probability distribution, moments, and moment relationships for a single stage of sampling are first reviewed, and the useful concept of unit moments is defined. In presenting the models for two stages of sampling, emphasis is placed on the physical description of the sample reduction process which leads quite naturally to its mathematical representation. In this representation, crushing or particle-size reduction between the stages of sampling is viewed as a random process with respect to the number and proportion of particles of the various kinds produced. The physical and mathematical description is extended to more than two stages of sample reduction, and the first three moments for any number of stages are developed. In common sample reduction practice the effects of a finite population (finite amount of material) at each stage of sampling appear to be important in describing the variance contribution of each stage. This is also true for the third moment about the mean. An example is cited in which the skewness increases by more than an order of magnitude when several stages of sampling are considered. This is largely due to the dependence of the multistage third moment about the mean on the variance. In general the model and results should be useful in helping to understand, control, and reduce the random errors that arise in the sample reduction process.

Jan 1, 1968