Search Documents

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume- percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By George E. Fasching

The Bureau of Mines has developed a pulse counting system with improved energy resolution and having dual channels to process pulses at different rates and a pulse pileup detector for channel selection. Pulse input is delayed until the detector determines if any pulse is so closely followed by a second pulse as to constitute pulse pileup. If no pulse pileup is detected, the slower channel is selected; this clips the pulse to a wide pulse width to retain good energy resolution. If pulse pileup is predicted, the fast channel, with correspondingly shorter pulse width, is selected to improve resolution with respect to time. Output of the two channels is transmitted to a pulse height analyzer for interpretation. The pulse processing system can process count rates above 300,000 counts per second with little loss in energy resolution.

Jan 1, 1974

By R. H. Grau, S. B. Robertson, R. B. Krog, T. P. Mucho

Stone mines represent the highest percentage of operating underground nonmetal mines in the United States. With the introduction of stricter Diesel Particular Matter (DPM) regulations, large-opening underground room-and-pillar stone mine operators are faced with implementing one or more alternative methods to reduce concentration levels including: install and maintain an effective ventilation system; install lower DPM emission diesel engines; the adding of DPM filters. The National Institute for Occupational Safety and Health (NIOSH) is actively researching various aspects of fan and stopping designs in an effort to improve the ventilation of these mines. NIOSH has identified and further developed three alternative ventilation methods for use in large-opening underground mines: split-mine, perimeter, and unit-ventilation. This paper describes the implementation of the three methods with respect to their use in mines of various levels of development.

By R. P. Vinson

The Bureau of Mines evaluated two real-time light-scattering dust monitors by measuring their response to Pittsburgh Seam coal dust and Arizona road dust (ARD). Both monitors, the model PDS-l, a personal dust sensor, and the model PCD-l, a digital dust indicator, are made in Japan by Sibata Scientific Ltd. Tests were conducted inside a laboratory aerosol chamber designed to maintain a uniform spatial distribution of the test dust. PDS-l and PCD-l measurements of concentrations for each test dust were averaged over 4-h test periods and compared with simultaneous gravimetric measurements. Both dust monitors responded linearly with mass concentration with both coal dust and ARD. However, the linear response of the PDS-l differed from that of the PCD-l for both dusts.

Jan 1, 1987

By Thomas P. Mucho, William D. Monaghan, John Wood, Michael A. Trevits

We have tested the ability of ground penetrating radar (GPR) to resolve adjacent mine workings. The work was conducted at two National Institute for Occupational Safety and Health locations – an underground coal mine and an underground limestone mine. The objective of our work was to determine if GPR signals could be received from distant mine workings. The GPR system was calibrated on underground mine pillars of known dimensions using a variety of antennas. The system was then tested at several underground locations in an effort to detect an adjacent drift entry; and an adjacent abandoned coal mine. As a means of verification, an in-seam horizontal hole was drilled from the active coal mine to the abandoned mine to confirm the presence and location of the abandoned mine workings. Our results show that in the case of the limestone mine the maximum depth of penetration where the mine workings could be resolved was 85 ft; and in the case of the coal mine the abandoned mine workings could be resolved at a depth of 205 ft. We conclude that it may be possible to utilize GPR for initial underground mine studies followed by directional drilling to accurately delineate the extent and position of adjacent abandoned mine workings.

Vanadium, molybdenum, and a titanium-10 percent vanadium alloy were evaluated for their susceptibility to stress corrosion cracking in a number of corrodents. Tests were conducted utilizing conventional U-bend techniques with subsequent evaluation in a pneumatic constant-load apparatus. Vanadium and molybdenum were generally resistant to stress corrosion cracking in the media studied. U-bend specimens of vanadium showed evidence of stress corrosion cracking in 6 li hydrochloric and 18 li sulfuric acids; however, tensile stress specimens exposed to these solutions did not exhibit stress cracking. Similar results were obtained when U-bend specimens of molybdenum were immersed in 10 percent formic acid. Titanium-10 percent vanadium alloy was susceptible to stress corrosion cracking in 10-percent (2.85 li) hydrochloric acid solution. Heat treating the alloy greatly reduced its corrosion rate and its susceptibility to stress cor-rosion cracking in this medium.

Jan 1, 1965

By W. N. Cathey

Many materials including carbides, silicides, phosphides, borides, nitrides, oxides, and metals were studied by the Bureau of Mines as potential fuel cell catalysts for electroreduction of oxygen in a 1[N]H2S04 electrolyte. The objective of this study was to assess the potential of abundant, low-cost materials as substitutes for platinum or to increase the catalytic efficiency of platinum. Several compounds were rejected because of their reaction in the corrosive environment of the oxygen electrode. However, some of the remaining were the most active catalysts. Activity of carbides such as tungsten carbide could be improved by doping with platinum-group metals, by varying stoichiometry, or by sputtering on a layer of platinum. While no catalysts were found with activity as high as platinum, some compounds were shown to be deserving of further investigation.

Jan 1, 1979

By Ted C. Briggs

A removable-jacket distortion apparatus was constructed and used to measure distortion coefficients for two high-pressure vessels. The measured distortion coefficients were used to compute distortion coefficients for volumes VI and (V1+V2) of a 1,000-atmosphere Burnett compressibility apparatus for the temperature range 0° to 75° C. Young?s modulus for Armco 17-4 PH stainless steel, heat treated to condition H1150-M, was computed from experimentally determined distortion coefficients. A 10-to 14-percent correction to the values obtained for Young's modulus may be required because pressure vessel end effects were neglected. The distortion coefficients of the compressibility apparatus are believed to be accurate to about 1 percent.

Jan 1, 1970

By Harold L. Rhodes

Vapor-liquid equilibria data for 65-34-1 and 25-27-48 mole percent helium-nitrogen-methane mixtures are presented for 12 temperatures from 76.5° to 164° K and pressures from 100 to 1,200 psia. These data were obtained in a windowed phase equilibria cell equipped with a vapor recirculating pump. Isobaric and isothermal K-values are plotted for both mixtures. Two isometric plots are included.

Jan 1, 1972

Prevent the propagation of a fire and control the spread of smoke and toxic gas in underground mines. Approach A fire door suitable for large openings in underground noncoal mines and providing protection for openings requiring 11/2 hours of fire resistance, a 250°F maximum temperature rise, and high pressure differentials was de-signed, laboratory tested, and in-mine tested. How It Works The door is a double-acting swing type. Its two panels. connected by an overhead linkage, open in opposite directions. Consequently, high pressure differentials across the door have little effect on the force required to open and close the door. The door is constructed of 14-gauge sheet steel skins welded to both sides of a 5-inch-wide steel channel frame. The frame is rein-forced with 5-inch-wide steel channels in a horizontal and diagonal pattern. The voids between the reinforcing members are filled with a ceramic fiber insulation material to limit the surface temperature rise of the unexposed side of the door during a fire. A fire -resistant neoprene-coated fabric is used to seal around the edges of the door panels. The door is opened and closed by an air cylinder, attached to the over-head linkage and operated by lanyards on either side of the door. The door design includes an optional airlock manway for drifts of adequate width.

Jan 1, 1983

By Robert G. Yewen, Ronald S. Conti

Underground mines rely on alarm systems, such as stench gas, audible or visual alarms, pager phones, telephones, and messengers to warn miners of a fire or other emergency. These systems are often slow, unreliable, and limited in mine coverage. This report describes the evaluation of a wireless signaling and warning system for underground mines. This system is applicable to both coal and noncoal mines. The work was conducted by the National Institute for Occupational Safety and Health in cooperation with TeleMagnetic Signalling Systems (TSS) under Cooperative3Research and Development Agreement No. BOM-CRDA-6200-0119. A TSS wireless ultra-low-frequency electromagnetic signaling system was installed at the Experimental Mine at Lake Lynn Laboratory near Fairchance, Fayette County, PA. A commercial smoke sensor was interfaced to a remote portable transmitter, and the alarm of the sensor was used to trigger the central evacuation and paging transmitter system during experimental mine fires. The underground/surface receivers flashed cap lamps and activated remote devices, such as strobe lights, within 30 to 40 s after the encoded signal was received. Evaluation results showed full-mine coverage of the electromagnetic field and that the encoded signal was received at the farthest point underground and on the surface perimeter.

Jan 5, 1997

By M. K. Larson, J. P. Dunford, E. G. Zahl, T. M. Brady

Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Spokane, WA, have collaborated with three Western longwall coal mines in an on going effort to develop technologies that will aid in providing safe and stable working areas. The goal of the research described here is to develop a stress monitoring system that will provide immediate information to mine managers for making daily safety decisions as areas of poor ground are mined through. Initial work has focused on answering preliminary questions regarding the reliability and use of stress change patterns. Research is concentrated on monitoring horizontal stress because horizontal stress is transmitted over long distances through stiff strata, thus allowing an extended length of entry to be monitored. This paper presents an explanation of the concept, key results from field tests at two mine sites, and a proposed process for implementing a monitoring system. System design layouts, instrument use, data collection and interpretation methods, and processes to present findings to mine staff are described. Additional validation and correlation with actual failure mechanisms are required before this approach can be recommended at ongoing operations. However, initial results indicate that this approach shows promise in mines prone to bumps and roof falls associated with large stress changes. In particular, analyses of measured changes in horizontal stresses appear useful.

By Motohisa Kanda

The time and amplitude statistics necessary to adequately describe electromagnetic (EM) noise in mines are illustrated through computer software techniques. They are 1) Allan Variance Analyses (AVA), 2) Interpulse Spacing Distributions (ISD), 3) Pulse Duration Distributions (PDD), 4) Average Crossing Rates (ACR) , and 5) Amplitude Probability Distributions (APD) . These statistics are illustrated using data taken from a rather large store of raw analog data recorded in operational mines. The curves generated for the illustrations characterize the noise environment in the mines from which the corresponding data were taken, and should aid in the design of reliable communication systems for such mines.

By F. E. Spencer

This Bureau of Mines report provides a complete mathematical description of the algorithm employed by a general multiphase chemical equilibrium program developed particularly for the purpose of studying problems in coal combustion, although the generality of the program will allow its application to any equilibrium system in which an appreciable gas phase is present. When applied to coal combustion problems, the program predicts composition and quantity of slag and unconsumed carbon phases as well as calculates accurately the composition of the gas phase including trace species such as free electrons and ions which are important for predicting electrical properties.

Jan 1, 1973

By H. B. Carroll

The Bureau of Mines investigated the adaptability of the Meteorology Research Inc.2 (MRI) nephelometer and the Sinclair-Phoenix smoke meter for use in routine, analytical, smog-chamber experiments and to compare their responses to aerosol during these experiments. Both instruments' sampling systems were modified--smaller size sample input systems were studied using the nephelometer and a secondary sample system was added to the smoke meter to allow measurement of Aitken or condensate nuclei. Both instruments were easily adapted for use with small smog chambers and both displayed good precision and sensitivity to aerosol. A correlation was shown to exist between the two instruments' responses to aerosol. This correlation makes it possible to report the Sinclair-Phoenix measurements in visibility and/or mass units if desired.

Jan 1, 1973

By D. Harrington

Fire is always a serious-menace, whether in a residential or in an industrial region; in wartime it is particularly damaging in an industrial plant. The mining industry is especially vulnerable, as its plants are generally more or less isolated front centers of population and do not have access to modern fire-fighting equipment; moreover, owing to the transitory rapture of most mines, their surface structures; are often relatively flimsy and flammable.. Trained firemen seldom are available at or near mining plants to teach the fundamentals of fire-fighting to local fire brigades, with the result that efficiency in combating actual fires is lacking. Often the attitude "it can't happen here" is held by the management of a mining property, unless the plant has suffered a serious fire; even then lapse of time is very likely to induce forgetfulness as to the possible hazards. The necessity for producing metals for the prosecution of this war has increased management's responsibility. Whereas heretofore the loss of a plant or mill by fire meant merely monetary less to the stockholder of the company, now the national interest is affected, in that the nation suffers from loss of production of minerals indispensable for war purposes.

Jan 1, 1943

By J. F. Messerly

The purity of three specially prepared samples of benzene was determined with an adiabatic, low-temperature calorimeter with automatic control of shield temperature. Extensive measurements were made on each sample to determine how variations in operating procedures affect melting-point and freezing-point as well as purity data obtained by the calorimetric method. Detailed results of the investigations are presented, and effects of different operating procedures are discussed, together with problems encountered in interpretating experimental results.

Jan 1, 1963

Reduce workers' dust exposure by capturing airborne coal and quartz dust generated by a continuous mining machine. Approach Install a water-powered scrubber system operating at 1,000 psi on the boom of a continuous miner at the conveyor throat. Dusty air from the face area is drawn through the scrubber and cleaned air discharged into the return. How it Works Most coal mines use exhaust face ventilation to send fresh air over the miner operator and contaminated air behind the line curtain to the return. The problem with exhaust ventilation is that the line curtain should be within 10 ft of the face for maximum effectiveness. If the line curtain is not extended properly, or water sprays for dust control are poorly installed, dust rolls back towards the operator. An effective way of removing this dust is with a scrubber mounted on the mining machine.

Jan 1, 1988

By Maria I. De Rosa

This report analyzes mine fires for all U.S. underground and surface metal/nonmetal mining categories during 1990–2001 by state and six successive 2-year time periods. Injury risk rates are derived, and ignition source, methods of detection and suppression, and other variables are examined. Fires involving contractors are also included in the analysis. The data were derived from Mine Safety and Health Administration (MSHA)mine fire accident publications and verbal communications with mine personnel. The analysis will provide the National Institute for Occupational Safety and Health, MSHA, and the mining industry with a better understanding of the causes and hazards associated with mine fires and an increased awareness aimed at preventing and reducing fire hazards. It will also form a basis for future fire research programs.

Jan 11, 2004

The U.S. Bureau of Mines evaluated water-jet-assisted longwall shearers in full-scale laboratory tests and underground. Both test programs showed that use of high-pressure water did little to reduce the shearer motor energy required to maintain a given cutting rate. However, three other major benefits were achieved with the use of water-jet-assisted cutting. At a pressure of 1,800 psi, respirable dust levels were reduced about 80 pct compared with the dust levels of the conventional water spray system operating at 340 psi. Operating at higher pressures required for water-jet assist also resulted in an increase in the average size of coal cut, which translates into a decrease in product fines. Finally, although no controlled measurements of bit wear as a function of water pressure were made, mine personnel reported that the shearer bits lasted longer when water-jet-assisted cutting was used.

Jan 1, 1989