Search Documents

By O. C. Blade

This report on the properties of motor fuels sold through service stations In the United States was made In accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items Is confidential. 1t presents analytical data for 4, 802 samples, representing the products of 117 companies. The samples were collected during December 1954 and January and February 1955. As in previous surveys, the gasolines covered 6y this survey Include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation, A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1955

By Thomas H. Dubaniewicz

Fiber optic systems are being deployed in locations where explosive gas atmospheres are normally present or are present under fault conditions. The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (NIOSH, PRL) conducted a study of laser safety in potentially flammable environments. Researchers conducted experiments to estimate the mean and standard deviation of laser powers needed to ignite 6% methane-air atmospheres using single mode optical fiber tips covered by two types of iron oxide (Fe304 and (FeMn)203) mixed with a ceramic adhesive. The iron oxides, heated by a 1064 nm continuous wave laser, ignited the methane-air mixtures ,at similar powers. The minimum igniting power and maximum non-igniting power (10 tests) were 407 and 350 mW, respectively, using a 62.5 pm fiber. Laser beams guided by 125 and 80 pm diameter cladding single mode fibers produced similar methane-air igniting powers. Ignition was not observed using coal particles at powers that produced ignition with the iron oxides. Threshold ignition delays using the single mode fiber were approxinlately proportional to the inverse square of the igniting power. Ignition delays were significantly longer than the reported activation time for a comnlercial fiber optic power limiter. Comparisons are made with the results of other researchers. Published by Elsevier Ltd.

By L. C. Marchant

Results of detailed analyses of four cores from the Threemile Canyon area in the P. R. Spring tar sand deposit in Utah are reported by the Bureau of Mines. The cores were obtained by the Utah Geological and Mineralogical Sur-vey as part of a l7-corehole evaluation program in the P. R. Spring, Hill Creek, and Rim Rock tar sand deposits. Average properties of the oil zone in the Threemile Canyon area as deter-mined from these cores are as follows: Oil saturation, 67.4 pet of pore volume; porosity, 29.2 pct; permeability before oil extraction, 133 millidarcies; and permeability after oil extraction, 2,855 millidarcies. Average net thickness of the oil zone is 23.8 ft and average depth to the top of the oil zone is 189 ft.

Jan 1, 1974

Until man was able to produce light, his working day was pretty much limited to daylight hours. Underground miners have a special problem because in a mine it is just as dark during daytime as it is at night. The first devices used for mine lighting were torches and open flame 011 lamps. Torches made from twisted grass and dipped in tallow or pine pitch would burn for a while, but they made a lot of smoke and probably went out when they were needed most. During the 15001s, miners lamps consisted of a small metal dish with a hook attached to hang it up. The saucer-shaped dish was filled with animal or fish oil and a wick made of twisted fibers was laid In the 011 and hung over one edge where it would burn. This lamp would burn longer than a torch, but the amount of light cast by the pale, flickering flame was probably only a little better than no light at all.

Jan 1, 1976

By John B. Goodman

This report presents a study of a modification of the precision laboratory carbonization-assay apparatus that renders the unit capable of performance at low-, medium-, and high-temperature assay levels and permits, under controlled conditions, evaluation of the relationship between carbonization temperature and the yield of pyrolysis products. Second, the interest and value derived from the temperature study data directly apply to the particular semiplant carbonization processes and techniques currently being investigated in this laboratory. Data obtained with the assay apparatus enables the fuel technologist to predict the probable yields of carbonization products from pilot-plant operations under various carbonizing conditions. Data obtained with the assay apparatus has been used to predict the product yields of industrial carbonization plants at Kemmerer, Wyo., and Rockdale, Tex. The assay provides a useful tool in detecting, from the carbonized plant product, the degree of effectiveness of pilot-plant operation. Third, the residual volatile matter in some industrial carbons has broad significance. Evaluation of the volatile material remaining with or in the carbon may be assessed through the high-temperature-assay technique. The low-temperature carbonization assay devised by the writers has proved to be a versatile tool in predicting the probable product yields from pilot-scale carbonization processes. The apparatus described in previous publications has been modified to extend the range of testing above 500° C. without impairing the accuracy and reproducibility obtained in the low-temperature range. Results presented here include product yields from a typical Texas lignite and Wyoming subbituminous-B-rank coal over the temperature range 150° to 1,000° C.

Jan 1, 1958

By W. A. Cole

Underground mining methods at the Gray mine of Tri-State Zinc, Inc., are of special interest because of the low unit costs achieved through use of jumbos and loading equipment mounted un crawler-type tracks and of diesel trucks that haul from the stoping areas to the mill through inclined adits. The operating company, Tri-State Zinc, Inc., is a wholly owned subsidiary of Gold Fields American Development Co., Ltd., the latter being the American branch of New Consolidated Gold Fields, Ltd., a British-owned company.

Jan 1, 1957

By MINE SAFETY BOARD

Mining men and State officials in their efforts to make mining safer are confronted from time to time with various complicated questions . In recent years these questions have tended to increase with the use of mechanical appliances . Twenty- five years ago electricity had hardly been used in mines . To - day there is practically no other means of transmitting energy employed in American mines , except in metal mines where compressed air is used for drilling and small portable hoists . In coal mines there has been a great increase in mechanization and a tendency to concentrate the mining operation , which has resulted in attendant difficulties of ventilation and intensified the danger of coal - dust in bituminous and subbituminous mines . The answers to the questions which arise are not always obvious , as is shown by the fact that even able , experienced men differ in their opinions of the best way to overcome a particular mining hazard . The difficulty of solving the problems is also demonstrated by the varying provisions in mine safety rules , both in official regulations and in the rules of those mining companies who are endeavoring to do more than follow the letter of the law . Such differences of opinion on the best way of meeting a difficult situation are often found within the same mining organization , and so it has been in the Bureau of Mines .

Nov 1, 1929

By W. H. Ode, W. A. Selvig

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County Colo., in connection with a survey of carbonizing properties of American coals 4/ and investigations of their chemical and physical properties. 5/ The coal represented by the sample from Weld County was reported to give off combustible volatile matter at unusually low temperatures when placed on a fuel bed. The yields of tar and oil and the composition of the as from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

May 1, 1937

By D. Bienstock

The Fischer-Tropsch synthesis is practicable in a reactor where the exothermic heat of reaction is removed by circulating large quantities of recycle gas through a catalyst bed of high-voids content. At an hourly space velocity of 1100, the feed gas, a mixture of 1.5 parts hydrogen to 1 of carbon monoxide, was converted 90 percent, producing hydrocarbons predominantly in the gasoline range. At these conditions a recycle-to-fresh gas ratio of 40:1 was enough to give excellent temperature control with a pressure drop of 1.5 p.s.i. per foot of bed using a steel catalyst in the form of lathe turnings. Steel parallel plates, although offering lower resistance to gasflow, were less reactive and less durable. INTRODUCTION The Federal Bureau of Mines has been engaged in a research and development program since 1944 on the synthesis of gasoline from coal. Gasification of coal with steam and oxygen to yield a synthesis gas--a mixture of carbon monoxide and hydrogen--is being investigated at Morgantown, W. Va.; and the synthesis of gasoline by catalytically reacting the carbon monoxide and hydrogen over iron by the Fischer-Tropsch reaction is being investigated at Bruceton, Pa.

Jan 1, 1960

By D. R. Babich, E. R. Bauer

The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of equipment sound levels and worker noise exposures in the stone/aggregate mining industry. Six stone/aggregate mines (three surface and three underground) were recently surveyed, and the findings (ire presented here. The surveys consisted of sound-level measurements conducted around various equipment and machinery (including stone processing and crushing equipment) and full-shift dose measurements to determine worker noise exposures. The findings identify the equipment and machinery that are likely to cause worker overexposures and identify the workers found to he experiencing overexposures. In addition, the benefit of cabs in reducing mobile equipment operator noise exposure is discussed.

By W. H. Ode

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County, Colo., in connection with a survey of carbonizing properties of American coals and investigations of their chemical and physical properties. The coal represented by the sample from Weld County was reported to give off combustible volatile matter at unusually low temperatures When placed on a fuel bed. The yields of tar and oil and the composition of the gas from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld. County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

Jan 1, 1937

By Wallace W. Roepke

The Bureau of Mines has a well-established health and safety research effort directed to fundamental studies of the mine cutting system. This report describes the ignition danger of using cutting bits with flat wear area on still-intact carbide inserts.

Jan 1, 1983

By Marting J. Gavin

The twentieth century has often been spoken of as the age of petroleum, and from many viewpoints it can be justly considered so. Certainly the petroleum industry is one of enormous importance to this country, industrially, financially, and economically. The United States, however, at present producing over 60 per cent of the world's total output of petroleum, is not producing petroleum at a sufficient rate to provide for its own domestic, consumption. For several years this country has been importing increasing quantities of crude and partly refined oils from Mexico, and has been drawing heavily on domestic stocks of petroleum. Production in the United States is increasing, but it is not increasing at the same average rate as domestic consumption, nor is it probable that in the future domestic production will increase sufficiently to satisfy the demands of domestic consumption, but on the contrary, in the opinion of those best qualified to know, the peak in the curve of domestic production of crude petroleum will be reached in a comparatively few years, whereas the consumption of petroleum and its product will increase at a continually growing rate. This country, then, must turn, and as the increasing imports from Mexico indicate, is turning to other sources than the crude petroleum, produced in this country to make up the deficit between domestic production and domestic consumption of petroleum and its products,

Jun 1, 1920

By G. A. Howes

This is one of a series of circulars dealing with the cost of equipping and developing mining properties in the United States and Canada, prepared and published by the Bureau of Mines in cooperation with various mining and exploration companies. This group of circulars is designed to supplement an earlier series which covered the methods and costs of mining and milling at a large number of producing properties. ACKNOWLEDGMENTS The authors desire to thank Robert A. Bryce, president of Macassa Mines (Ltd.), for permission to use the data presented in this paper, and to acknowledge the cooperation of A. J. Keast, under whose direction as manager the plant was installed and equipped and the shaft was sunk to a depth of approximately 2,000 feet.

Jan 1, 1932

By James L. Konchesky

Crushed coal, consisting of a wide range of sizes, was effectively blended by recycling it through a bin equipped with a particle distributor. Vertical blending was accomplished by simply recycling the coal; it was not significantly influenced by the horizontal blending that was achieved by the distributor. The method was effective, even though the coal was wet and possessed poor flowing characteristics. Recirculation appears capable of providing uniform blends of solids that can be more efficiently processed. Recirculation also appears useful, preceding packaging operations, to insure for blending of solids into specification products. Continuous measurement of the bulk density of the coal by a gamma ray meter proved to be an effective monitor of vertical blending effectiveness.

Jan 1, 1972

By Philip E. Sanker

The Bureau of Mines conducted small-scale batch and semicontinuous tests on the reduction of zinc sulfide with iron according to the reaction ZnS + Fe ? FeS + Zn to determine reaction kinetics in the temperature range 1,000° to 1,400° C and to investigate the potential use of a scrap iron reductant. Batch tests indicated that a temperature of at least 1,300° C with a 1:1 mole ratio of Fe to ZnS is needed for good zinc recovery. Semicontinuous tests were conducted, using four zinc concentrate samples, containing various percentages of copper, cadmium, and lead, which were reacted with iron and iron contaminated with iron oxide and tin in an externally heated graphite furnace. Analysis of the zinc metal and FeS matte reaction products showed cadmium to be entirely in the zinc metal, copper to be in the FeS matte, and lead to be about 60 pct in the zinc metal and 40 pct in the matte. Tin reported to the matte, and none was detected above the O.OS-pct level in the zinc. Sulfur dioxide was not detected in the offgas when up to 20 pct of the iron was replaced by Fe203.

Jan 1, 1976

By Robert W. Freedman

Vacutainers are used by the Bureau of Mines and the Mining Enforcement and Safety Administration (MESA) for sampling mine air and products of combustion. Tests were conducted on both 10-ml and 30-ml sizes to study shelf life stability during storage, pretreatment of stoppers, and handling of a wider range of compounds. A chamber was constructed to provide convenient, efficient evacuation of the Vacutainers shortly prior to use. Fixed gases and C1 ?C5 hydrocarbons could be stored for 1 week or more after sampling. Where decreases occurred (C02 and C3-C5 hydrocarbons), they were predictable as a function of storage time. An unexplained phenomenon, slow accumulation of CO in evacuated Vacutainers, occurred after a few weeks of storage. The levels were low and time dependent. Attempts to eliminate this behavior by pretreating the stoppers were unsuccessful.

Jan 1, 1976

By Fred C. Turin, Lisa J. Steiner, Kim M. Cornelius

Like many experienced workers, remote control continuous miner operators perform their everyday jobs making choices and decisions that they may not consciously think about. While performing tasks, they are continuously processing feedback and cues which guide them for the next move. Initial training teaches the operators the tasks necessary to operate the equipment and perform the job. However, with experience they are better able to deal with hazardous conditions and non routine situations. To better understand what potential cues and feedback help to guide the operators, a questionnaire was developed to learn what factors affect decisions. Operator responses address issues related to specific tasks, equipment operation, visibility, lighting, and communication issues. The information collected is useful to understand what cues experienced operators use to make task performance decisions. Results will be used to develop interventions and training for safe and effective operator performance.

By F. R. Cattoir, T. A. Sullivan

Commercial uranium metal was electrore fined to a high- purity product using molten- salt electrolytes in an inert atmosphere cell . Electrorefined uranium that contained , after consolidation , less than 30 ppm of metallic impurities was prepared . A method of leaching the electrolyte crystals to remove the salts was developed . Cathode current efficiencies from 90 to 100 percent were obtained . Two molten- salt electrolytes were prepared and evaluated : (1 ) lithium chloride - potassium chloride - uranium trichloride and ( 2 ) sodium chloridepotassium chloride - uranium trichloride . Very little difference was found in the purity of the uranium metal produced in either system . The lithium chloride - potassium chloride - uranium tri - chloride electrolyte was preferable from an operational standpoint .

Jan 1, 1964

By K. A. Johnson

Marshall and Bird have published the results of a cooperative investigation by the Bureau of Mines in which they developed a procedure for measuring the agglutinating value of coal.4 As stated in their paper, the procedure outlined was suggested by the early worn of Richters5 and Campredon,6 whose procedures were hurriedly modified to meet the need of an investigation then in progress. Since the publicatien of that paper, further work has been done in an attempt to show how the variables involved affect the concordance of the results, in order that such results may be obtained in different laboratories. Briefly, Marshall and Bird's method for determining the agglutinating value of coal consists in carbonizing an intimate mixture of 10 parts by weight of sand and 1 part by weight of coal in a porcelain crucible at a uniform temperature of 950° C. in a, vertical, cylindrical, electrically-heated furnace. After carbonization, the resultant buttons are crushed in a testing machine and the breaking strengths recorded in grams. The agglutinating value reported is the average breaking strength of 10 buttons. The coal for the test is prepared by crushing to pass a 100-mesh screen. The sand used as a diluent is sized between 40 and 50 mesh sieves with openings of 0.381 icon and 0.279 millimeters, respectively.

Jan 1, 1930