Search Documents

By R. V. Subramanian

This project financed by the Bureau of Mines investigated the use of polymers to achieve rock bonding and reinforce coal mine structures for better or permanent ground support. Support was achieved by pumping the polymers into the rock interstices to bond the mass together for increased structural competence. Holes were drilled in the mine roof, after which the polymers were injected at about 100 psi to permeate the cracks. Initial laboratory work indicated that of all the resin systems tested, the epoxy resins could most likely be modified to be suitable for rock injection. This was confirmed when several potentially suitable resin systems underwent intensive evaluation. In a series of three field tests, two conducted in a copper mine with coal mine-type shale and the third in a coal mine, it was shown that the polymers penetrated cracks less than 0.005 inch wide. The fast-setting epoxy systems, cured out in thin films under mine conditions, produced a bond exceeding the strength of the uncracked virgin rock.

Jan 1, 1974

Provide reasonably priced, reliable fire protection for front-end loaders. Approach Automatic fire sensing and suppression systems were developed and ruggedized for use on front-end loaders operating in harsh mine environments. How It Works Temperature sensors mounted in the loader's engine, transmission, and articulation areas detect the heat from a fire while it is still small and controllable. This triggers the release of the ABC class dry chemical extinguishing agent through a fixed piping system onto the fire. The system can also be manually activated from either the cab or ground level. Locations of the principal components of the system are shown in the drawing. Two control subsystems were designed to respond to varying fire protection needs and mine conditions. One subsystem only initiates discharge of the extinguishing agent. The other subsystem initiates visual and audible operator alarms if there is a fire sensed or if there is a fault in the control circuit.

Jan 1, 1979

By Alla D. Mah

Combustion energies of barium and strontium were measured by means of the combustion bomb calorimeter. The heats of formation obtained for the oxides were ?H298.15 = -139,060 ± 700 cal/mole of barium oxide (BaO) and ?H298.15 = -144,440 ± 400 cal/mole of strontium oxide (SrO). Tables containing heats and free energies of formation from 298.15° to 2,000° K were prepared.

Jan 1, 1963

By Bill M. Stewart, Philip W. Patton, Curtis C. Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines we revisited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

By Robert K. Koch

Laboratory-scale studies on defluorination of natural and synthetic fluorspars by pyrohydrolysis at 1,500° C. were made to determine the feasibility of developing a process for producing hydrogen fluoride from siliceous fluorspars. It was found that the reaction (at 1,500° C.) is not promising for process development, even though a silica-free offgas can be generated. The primary difficulty is the low hydrogen fluoride content of the offgases; an HF content of 6 percent was the best achieved. Previous research by the Bureau of Mines has demonstrated that offgases averaging 27 percent hydrogen fluoride can be produced under carefully controlled conditions at 1,280° C. The lower temperature process is a better method for production of HF. However, charges in which the CaF to Si02 mole ratio varied from 0.4 to 2 could be processed with similar results. Also, combined alumina and ferric oxide contents up to 25 mole-percent did not noticeably alter the rate of defluorination. Therefore, virtually any natural siliceous fluorspar would respond in essentially the same manner when exposed to water vapor at 1,500° C.

Jan 1, 1962

This part of the final report treats some problems related to coal mine carrier frequency communication systems using the trolley wire/track transmission line. This work was undertaken for a brief period of time during the summer of 1972 to help understand, quantify, and improve some of the trolley wire carrier system behavior observed and/or predicted. Calculations and estimates of transmission line characteristic impedance, inductance and capacitance per unit length, mine motor loading effects, parallel line effects, and connection impedances are presented in Chapter I. Chapter II treats the design of r-f isolators for reducing the undesired and troublesome r-f loading that mine motors present to the trolley transmission line. Chapter III treats a diversity method for combatting standing wave nulls. I. CALCULATIONS RELATED TO TROLLEY WIRE COMMUNICATIONS A. ESTIMATION OF INDUCTANCE AND CAPACITANCE PER UNIT LENGTH OF TROLLEY LINES To estimate the L and C per unit length of trolley lines, we use the eccentric line model of Section G of this Chapter, "Characteristic Imped¬ance Estimates for Mine Trolley Lines." The capacitance per unit length for an eccentric line is given by (1)

Jan 1, 1974

By Arthur Metcalfe, Edward Thomas, A. J. Barry

"Early in 1947 the Bureau of Mines became interested in adapting suspension roof support to coal mining 5/ as a possible means of reducing the high rate of accidents from falls of roof. For a time the program made little progress be¬cause of the shortage of steel products after the end of World War II, but during the past 8 months this restriction has eased, and as of May 1, 1949, 114 mines had either started experimental work or had ordered materials and equip¬ment in anticipation of trial installations. It is estimated that 30 linear miles of roof in underground passageways have been secured by this method in recent months, and no lost-time roof-fall accident has been reported in these areas up to that date.Many coal-mining companies in widely separated localities have cooperated in making experimental installations. In very few instances are these companies entirely satisfied that they have arrived at the best solution in determining the most efficient adaptation to suit their particular conditions. Moreover, new ideas and modifications of the basic principle are constantly being brought to light and are being tested. Available test data is far from complete, and it is conceivable that some new idea will be developed to alter the present concept of proper technique; therefore, this progress report does not attempt to answer all questions that might arise in connection with this method of roof support; it simply recounts the experience acquired to date. Consequently, few references to costs are made. Up-to-date quotations on material and equipment used in suspension roof-support installations may be obtained from numerous mine-supply companies.The authors gratefully acknowledge the cooperation of mining companies whose personnel made possible collection of the information contained in this circular: Bethlehem Collieries Corp., Barrackville, W. Va.; Berwind-White Coal Mining Co., Windber, Pa.; Consolidation Coal Co., (Ky.); Jenkins, Ky.; Consolidation Coal Co. (W. Va.), Fairmont, W.Va.; Clinchfield Coal Corp., Dante, Va.; Consolidated Coal Co., St. Louis, Mo.; Hanna Coal Co., St. Clairsville, Ohio; Missouri Portland Cement Co., Sugar Creek, Mo.; Pocahontas Fuel Corp., Pocahontas, Va.; Reppert Coal Co., Dola, W. Va.; St. Joseph Lead Co., Bonne Terre, Mo.; and Tennessee Coal, Iron, & Railroad Co., Birmingham, Ala.The fundamental theory of suspension roof supports is not new; in fact, its application in the construction of beams predates mining itself. The basic principle involved is the reinforcement of roof rock with steel rods inserted in the roof and anchored therein at points where the rock is least likely to be affected by stresses resulting from mining. Such roof supports have been used in mines for many years in widely separated localities. The St. Joseph Lead Co., operating in southeastern Missouri, apparently was the first large mining company to prove the practicability of the principle by applying it in a systematic manner for securing roof for more than 20 years (fig. 1)."

Sep 1, 1949

Etching solutions containing hexavalent chromium ions (e.g., chromic acid) are used in brass finishing, printed circuit board etching, preparation of plastic for plating, anodizing, and various other industrial surface treatment operations. As the solutions are used, hexavalent chromium ions are reduced to their trivalent state, contaminants accumulate in the solution, and the effective acid concentration is reduced. When the etching rate becomes unsatisfactory for the particular operation, the solutions are discarded. This is a problem because the discarded solutions are pollutants, and because replacing the etching solution is expensive. The Bureau of Mines has developed a process for regenerating these spent solutions and returning them to the surface treatment operation without interrupting the etching process. An electrolysis cell containing anode and cathode compartments that are separated by permeable membranes, is used for regenerating the spent solutions. The spent chromic acid solution is fed to the anode compartment and sui (uric acid is circulated in the cathode compartment. Application of a steady electrical potential of a few volts dc across the electrodes causes the copper ions and other contaminants in the spent solution to migrate through the membrane to the cathode compartment where copper is plated onto the cathode. Zinc and the other contaminants remain in the sulfuric acid. At the same time, the complex, trivalent chromium ions in the spent solution are attracted to the anode where they are oxidized to their original hexavalent state. The regenerated solution in the anode compartment is then recycled back to the plant?s etching operation for reuse.

Jan 1, 1980

By L. Cheng

This Bureau of Mines report summarizes an investigation of the amount of respirable dust adhering to the surfaces of seven run-of-face broken bituminous coals. The number of respirable-size (0.9 to 10 micrometers) particles adhering to the run-of-face coal ranged from 1011 to 1012 particles per pound of coal and was approximately inversely proportional to the mean lump size of the coal sample, otherwise it did not vary significantly with the coal seam, mining method, or winning machine. Based on these results, about 16 lb of ordinary run-of-face broken coal would have enough respirable-size adhering dust to contaminate 1,000,000 ft3 of air up to the 2 mg/m3 level, if this adhering dust should become airborne. Although brief studies here suggest that a negligible amount of new respirable dust is formed due to fracture of the broken coal during dropping, dislodging of old adhering particles during secondary handling operations is a potentially dangerous source of airborne respirable dust.

Jan 1, 1973

By Walter W. Hyde

This paper describing the mining and preparation of sand and gravel for a number of special markets by the East Texas Gravel Co., Dallas, Tex., is one of a series being prepared on the subject by the United States Bureau of Mines. These articles are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole, but on the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1931

By J. J. McClelland

The face area of a continuous mining section of an underground coal mine is the most dangerous area in the mine. Workers there are at nearly twice the risk of death or disabling injury than those in other parts of the mine. Despite extensive training of miners and improved equipment and mining methods, fatality and injury rates have remained constant during the past few years. It is clear that advanced research is necessary to apply new technologies or modify work procedures to solve the continuing problem of the loss of lives and the numerous injuries at the mine face. A U.S. Bureau of Mines research program is developing a Reduced-Exposure Mining System (REMS) that relocates personnel operating the mining machinery at the face away from the hazards to a nearby haven of relative safety. REMS uses proven technologies of computer automation and robotics to help control the operation of the mining machines at the face, while personnel are moved away to a nearby, safe control room. In this protected, well-ventilated environment, they can supervise or control the operation of the machines while viewing what the machine is doing using video and graphic display monitors.

Jan 1, 1994

By Oliver Bowles

"The manufacture of asbestos paper began commercially about 40 years age but its principal development has taken place during the past twenty-five years. The asbestos used by the ancients, termed amiantus by Pliny was used for winding sheets, tablecloths and other fabrics. It was probably chrysotile fiber and was a woven and not a felted product, and there¬fore is not to be confused with asbestos paper. There are, however, some early references to paper manufacture that are of interest. Pontoppidian, Bishop of Bergen, in his Natural History of Norway, published in 1750, refers to paper made from asbestos found in the parish of Waldens. He states that this paper did not burn when thrown in the fire, but the writing on it totally disappeared. This indicates that the primary ob¬ject was to obtain an indestructible writing paper. About 100 years later, further efforts were made with the same object in view. In 1853, a patent was issued for a process of making paper from a mixture of asbestos and alum. Many experiments were made to manufacture suitable asbestos printing paper. Some such papers contained only about one-third asbestos, the remainder being of combustible material. Such papers would burn, but would leave a white residue which retained its shape and preserved the written characters. On account of the difficulty of obtaining a smooth and even surface, and the tendency for the material to absorb ink like blotting paper, asbestos paper is not well adapted for writing or printing purposes. Other early uses of asbestos paper were for ornamental wall-paper and carpet linings. None of the uses mentioned above have developed to anything of importance in a practical way, but the manufacture of asbestos paper has become a very important industry, and it has found extensive uses in ways that were never dreamed of by the early investigators.It is recorded that the first sheet of asbestos paper made in America was manufactured in 1876 by John Roberts & Son Company, in a mill near Waltham, Mass. The material first used was a long-fibered amphibole asbestos from Italy. About three years later, Canadian fiber was introduced and proved to be very satisfactory. The shorter grades of fiber which would otherwise be wasted were used for the manufacture of paper and board. For several years, the product of this mill was sold through Rice Kendall of Boston, Mass. From 1881 to 1900, the H. W. Johns Company, of New York, took the entire product which was 30C to 700 tons per year. The latter company built their own asbestos paper mill at Brooklyn in 1900. Keasbey & Mattison Company, of Ambler, Pennsylvania, began to manufacture in 1897. Other early manufacturers were: the Asbestos Paper Company, at Baldwinsville, Mass„ and Mr. B. S. Binney, at Shirley, Mass. The number of manufacturers gradually increased until at present asbestos paper is manufactured by the following ten companies:"

Nov 1, 1919

By Charles L. Ross

A successful placer mine is being operated by the E. T. Fisher Co. on Rock Creek in the South Pass mining district at Atlantic City, Wyo. About 2,800 cubic yards of gravel is dug daily by a gasoline-driven dragline shovel with a 1 1/4-yard bucket and washed in a movable plant with a gold-dredge trommel and standard-dredge sluice boxes; the total cost is about 12 cents per cubic yard. The gold-bearing gravel occupies a narrow valley between two low ranges, of hills. The ground is covered by brush and willows, which are cleared of in the fall by burning after the leaves have dried. The elevation at the mine is 7,600 feet above sea level.

Jan 1, 1935

By Benton L. Tibbetts

Comprehensive geophysical measurements were made in the Tertiary Channel gravel deposits of Badger Hill, Calif., with the refraction seismograph, gravimeter, and well logging equipment, to develop a three-dimensional physical model of the gold-bearing gravels. Tests were also made of the applicability of magnetometer and electrical resistivity techniques. Results of 14 seismic profiles revealed four distinct layers with velocities of 1,600 ft/sec for loose gravel, 5,900 ft/sec for compact gravel, 8,600 ft/sec for cemented, blue gravel, and 15,500 ft/sec for bedrock. The depth to bedrock along the middle of the channel varied from a minimum of 100 feet in the hydraulically mined pit area to a maximum of about 300 feet in the upper bench area immediately south of the pit. These geophysical methods revealed that 40 percent of the drill holes necessary to delineate the deposit could be eliminated, at a cost saving of at least 30 percent.

Jan 1, 1971

By Dean H. Ambrose

The U.S. Bureau of Mines recently developed computer graphics simulations to characterize mining scenarios, specifically for room-and-pillar mining operations in a three-entry longwall development section. These simulations compare productivity between shuttle car and continuous haulage systems concepts. One of the continuous haulage systems concepts has bolting capabilities that supplement haulage function. Simulations showed the continuous haulage system to be more time efficient than the shuttle car system. Researchers can reuse the simulation code (e.g., mining rates and equipment capacities can be changed) should investigators care to compare production of other mining scenarios. computer simulation, found computer model modification flaws and mining scenario conceptual errors. The fundamental rationale for three-dimensional computer is to cheaply, easily, and quickly obtain information about operation and of a current or proposed mechanical coal or metal/nonmetal mining system. This report documents the computer graphics model and simulation developments and discusses some of the results and observations from the simulations.

Jan 1, 1994

Reduce worker exposure to respirable dust without interfering with bag-filling operations. Approach A dust control hood was developed which contains and captures dust close to its source and prevents it from entering the bag-filling operator's work place. How It Works A sheet metal hood is placed around the nozzle of the bag filling machine. The hood is connected through ducts to the plant exhaust ventilation system. Air pulled into the front of the hood and around the sides of the bag picks up dust generated inside the hood, and carries it to the dust collector. The size of the hood can be adapted to fit most fluidized valve-type bag-filling machines. The height of the hood depends on the bulk density of the product and weight of the bags being filled. The 14-inch-width of the hood allows it to be used on multi-nozzle baging machines spaced 16 inches on center. Only 2/3 of the bag is actually within the hood, and this allows easy operator access for placing the bags on the nozzle.

Jan 1, 1978

By McHenry Mosier

Diamond -drilling blast holes at Eastern Magnetite Mine C is proving economical in boundary shrinks , in removing pillars not readily accessible for percussion drilling , and in driving scraper drifts . The cost per foot drilled is greater than for percussion drilling , but savings in associated factors outweigh this handicap . The rocks drilled include trap rock and magnetite ore . The mining method is the panel , block- caving system utilizing scraper sublevel drifts instead of branch raises to convey the ore to the haulage level . Diamond -drilling blast holes was begun early in 1945. Three rigs equipped with noncoring bits are now in active operation two shifts per day . They are owned by the company , and the drill operators are paid by the day . In shrinkage stopes the drill is mounted on a horizontal bar set against opposite walls of the stope . Stoping holes are horizontal , which gives better results in blasting and requires fewer set ups . In scraper drifts the drill is mounted on a horizontal bar clamped to two columns about feet apart . Trim holes around the periphery of the drift and reliever holes are drilled 50 to 80 feet in length . A 10 - foot wedge cut drilled with a stoper is blasted in conjunction with a corresponding length of the trim holes to effect a 10 -foot advance of the full- sized drift . Recent drilling averages 97 feet per machine shift , excluding time utilized in setting up and moving the machine , hand mucking , and barring down . The feet drilled per bit at present is 417. These data represent the average for drilling in both rock (waste) and ore . Percussion drilling utilizes three types of wet drills . Detachable bits are standard . Gage changes for new bits is 1/8 inch and for reconditioned bits 1/16 inch . The life of a bit is five uses . Resharpening is on contract . A drill carriage is used in haulage headings .

Feb 1, 1948

By G. W. Weems

The Bureau of Mines combined preconcentrating techniques and mass spectrometry to develop a parts-per-billion general analysis of impurities in helium. The impurities are preconcentrated using a Bureau trace-impurity analyzer; 35-mm Hg pressure of helium is left in the concentration trap to sweep the impurities into the mass spectrometry and provide a 10-mm Hg sample pressure.

Jan 1, 1966

By Mary H. Brown

The heats of formation of oxalic acid and sodium, potassium oxalates, and lithium oxalates were related by solution calorimetry to the heat of formation of (COOH)2.2H20, a value believed to be reliable as reported in the literature. The following heats of formation were determined: (COOH)2(a), -198.1±0.1; (COOH)2(ß), -197.8±0.1; UAW,, -328.7±0.4; Na2C204 -316.2±0.1; K2C204, -321.9±0.2; and K2C204-H20, -393.5±0.2 kcal/mole. The heat of the crystalline transformation (COOH)2(a) ? (COOH)2(ß) was determined to be 0.30±0.02 kcal/mole at 298.15° K.

Jan 1, 1970

By Maria I. De Rosa

Table 19 and figure 7 show the number of fires and fire injuries for surface coal mines by state during 1990-1999. Table 19 also shows by state the risk rates, employees' working hours, lost workdays, and coal production. For surface coal mines, 215 fires occurred in 21 states during 1990-1999. Ninety-four of those fires caused 93 injuries and I fatality (the yearly average was 21.5 fires and 9.3 fire injuries). Fourteen fires and seven injuries involved contractors. The Ewhr value was 729 x 10° hr (In = 0.026), the CP value was 6,355 x 10° st (Fn = 0.034), and the LWD value was 8,141. Kentucky had the most fires and fire injuries (45 fires and 23 injuries), followed by Pennsylvania (33 fires and 14 injuries), West Virginia (25 fires and 14 injuries), and Indiana (20 fires and 8 injuries). Among these states, Pennsylvania had the highest fire risk rate value (Frr=0.145), while Kentucky had the highest injury risk rate value (In 0.041).

Jan 1, 2004