Search Documents

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page, Linda J. McWilliams, Gerald J. Joy, Steven E. Mischler, Jon C. Volkwein

The United States National Institute for Occupational Safety and Health, through an informal partnership with industry, labor, and the United States Mine Safety and Health Administration, has developed and tested a new instrument known as the Personal Dust Monitor (PDM). The new dust monitor is an integral part of the cap lamp that coal miners normally carry to work and provides continuous information about the concentration of respirable coal mine dust within the breathing zone of that individual. Previous laboratory testing demonstrated that there is a 95% con?dence that greater than 95% of individual PDM measurements fall within ±25% of reference measurements. The work presented in this paper focuses on the relationship between the PDM and respirable dust concentrations currently measured by a coal mine dust personal sampler unit utilizing a 10 mm Dorr Oliver nylon cyclone. The United Kingdom Mining Research Establishment instrument, used as the basis for coal mine respirable dust standards, had been designed speci?cally to match the United Kingdom British Medical Research Council (BMRC) criterion. The personal sampler is used with a 1.38 multiplier to convert readings to the BMRC criterion. A strati?ed random sampling design incorporating a proportionate allocation strategy was used to select a sample of mechanized mining units representative of all US underground coal mines. A sample of 180 mechanized mining units was chosen, representing approximately 20% of the mechanized mining units in production at the time the sample was selected. A total of 129 valid PDM/personal sampler dust sample sets were obtained. A weighted linear regression analysis of this data base shows that, in comparison with the personal sampler, the PDM requires a mass equivalency conversion multiplier of 1.05 [95% C.I. (1.03, 1.08)] when the small intercept term is removed from the analysis. Removal of the intercept term results in a personal sampler equivalent concentration increase of 2.9% at a PDM measurement of 2.0 mg m-3.

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel.oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which typo of plant utilizes more thou the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which crude oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining. Although no outstanding technical developments of a fuel-saving nature were made in 1934, some progress undoubtedly was recorded. Heat exchangers, an effective fuel-saving device, wore enlarged, and some refiners now take off several cuts before the crude reaches the pipe stills. The total capacity of pipe stills increased 2.5 percent in 1934, and many of the less efficient shell stills were torn out.

Jan 1, 1935

By H. E. Powell

The smelting of brass and bronze generates a dust composed primarily of zinc oxide, with lesser amounts of other metal oxides, such as copper, lead, and tin. The small quantity of this waste generated by individual smelters and the relatively low unit value of the contained metals, suggests the desirability of reclaiming the metals onsite or at some nearby point. The Bureau of Mines has developed a process that fits these requirements. The technique consists of (1) dissolving zinc and copper from the dust with sulfuric acid, (2) recovery of copper by cementation, (3) recovery of zinc as zinc sulfate crystals, and (4) recovery of lead and tin as a salable residue. Alternatively, zinc may be recovered by electrodeposition. Free acid is recycled and no major pollution problems are generated by the process.

Jan 1, 1972

"In sum, significant benefits to mine worker health have resulted and should continue to result from the synergistic scientific, engineering, and medical research in respirable dust. As always, an important objective is the rapid dissemination of the results of this research to industry. Video tapes and the Technology News series published by the United States Bureau of Mines (USBM) have been a very effective means of technology transfer. Individual no-cost subscriptions to the Technological News series are available from the Bureau of Mines, Branch of Technology Transfer, 2401 E St., N.W. Washington, DC, 20241.Two respirable dust conferences have been jointly sponsored by the Center, USBM, NIOSH, and MSHA. The proceedings from these conferences are titled:1. Coal Mine Dust Conference held in Morgantown, West Virginia on October 8-10, 1984 and2. Respirable Dust in the Mineral Industries: Health Effects, Characterization and Control held in University Park, Pa. on October 14-16, 1986.Copies of the proceedings from the first conference are available from the National Technical Information Service (NTIS):National Technical Information Service5285 Port Royal RoadSpringfield, VA 22161NTIS # PB86-169380Telephone Number: (703)487-4650Copies of the second conference proceedings, ISBN: 0-936712-76-7 (publication #3010), are available from ACGIH by writing toWilliam D. KelleyExecutive Director, A.C.G.I.H.6500 Glenway Avenue, Building D-FCincinnati, Ohio 45211Telephone Number: (513)661-7881During the period 1984-1987 more than sixty-four (64) papers and publications have been produced by the Center researchers. These publications have appeared in scientific journals and have been presented at national and international symposiums and meetings. A list of these papers, organized by topical headings, has been included in this publication.The generic center maintains a reference center that serves as a clearinghouse for technical information for the generic area and supplies reports on generic center accomplishments."

Nov 1, 1988

Develop a reliable, portable device for non-destructively testing the support integrity of a friction rock support (commonly referred to as a Split Set ). Approach The friction rock support, used to support mine roof and ribs, is a slotted tube driven into a drilled hole of smaller diameter. Upon installation, the tube is compressed radially. The amount of compression is a function of the hole diameter, the strength of the host rock, and the properties of the split set itself. A simple lightweight self-contained device was developed to determine the pull-out resistance of the friction rock supports in-situ, based on measurements of the tube's deformation. The tester measures the com-pressed internal volume of the slotted tube, which has been found to provide an estimate of the support's resistance to pull out. How It Works The tester consists of a pump and expander sections. The expander sections are made from an elastomer membrane which is stretched over two cores, each one inch in diameter and twelve inches long. The expanders are connected by a flexible coupler so that they can fit any alignment of the support.

Jan 1, 1984

By L. B. Pankratz

Low-temperature heat capacities, high-temperature enthalpy increments, and the enthalpy of formation at 298° K were determined calorimetrically for vanadium subnitride (VN0.465). The low-temperature investigation gave S°298.15 = 6.379 ±0.005 cal/deg mole, and a combustion calorimeter investiga¬tion provided ?Hf°298.15 = -31.80 ±0.60 kcal/mole. The two quantities were combined with the high-temperature data to give standard values of enthalpies of formation and free energies of formation above 298° K. These and related thermodynamic functions were tabulated to 1,800° K. Similar data are included in the range of 298° to 1,600° K for the mononitride, VN.

Jan 1, 1971

By John D. Corrick

The environmental and nutritional characteristics necessary for maximum copper extraction from a low-grade ore by Ferrobacillus ferrooxidans have been explored as have many of the limiting parameters. Criteria considered were oxygen consumption, copper extracted, soluble copper concentration, temperature, pH, particle size, nutrients, and other inorganic salt concentrations. A set of environmental and nutritional conditions were developed for E. ferrooxidans Which supported cell reproduction and maximum microbial oxidation of a low-grade copper sulfide ore. Percolator tests conducted under these optimum conditions resulted in an 18 percent increase in the quantity of copper microbially extracted over that extracted under conditions considered to be standard. Manometric tests determined those extremes of environmental conditions and nutritional factors Which were detrimental to the extraction of copper by E. ferrooxidans.

Jan 1, 1965

By Alan G. Mayton

A prototype end-cab shuttle car (SC) design has been developed to improve protection and address ergonomic concerns of the SC operator in low coal mines. The new design features an end cab transversely mounted to the SC and equipped with a closed-circuit video system. The end cab was retrofitted to a low-coal SC and evaluated in surface trials at the U.S. Bureau of Mines. During surface trials, test operators evaluated the end-cab SC relative to visibility; cab features-space, seating, controls, and operator position; tramming-inby, outby, and turning corners; and dumping. Trials were conducted using 12 test subjects; 6 were experienced SC operators. Results of the trials were promising. Of the experienced operators, the only operator with low-coal experience gave the new design the highest rating. Four experienced operators rated the end-cab design "better" to "much better" than a standard center-driven, side-cab SC for visibility when tramming, protection from roof and rib hazards, and no change in seat position with direction of travel. This report discusses research to modify a used 21SC JOY SC, retrofit the SC with the Bureau-developed end-cab, and evaluate the retrofitted end-cab SC in surface trials.

Jan 1, 2010

By C. Melvin Lepper

High-resolution shallow seismic reflection methods are being used by the Bureau of Mines to map underground geologic features in coal mines. These features include faults, channel sand, washouts, rolls, and steep dips. The seismic method is proving useful for locating all of these at reasonable cost and with better definition than available with drill programs alone. This report provides a capsule description of the techniques and their application to mine planning.

Jan 1, 1976

By C. J. Cohen, L. A. Dahners

"SUMMARYA method has been developed for surveying, drill holes without lowering into the hole any surveying equipment other than an etch tube. The orientation of the rods at the collar of the hole is maintained as the etch tube is lowered. The attitude of the etch ellipse in depth with respect to the rod orientation at the collar can then be observed. This relationship permits the bearing of the hole in depth to he calculated. The rod orientation is maintained during the lowering by means of a pair of alinement clamps. One clamp is fastened to the top of each rod as the rod is coupled and is removed when the alinement has been transferred to the other clamp at the top of the next succeeding rod. A particular advantage of this survey technique is that surveys can be readily made in magnetic country rock.PRINCIPLE OF THE TECHNIQUEAn axial lamina of the column of drill roes is the lamina in which one fiber would be the centerline of the rods. In the new survey technique, the rods are fed into the hole in such a manner that the axial lamina of each successive rod maintains its position at the collar of the hole. In depth, as the rods bend in following the drill hole, the axial laminae also bend. The lamina that was originally vertical will, in general, be tilted away from the vertical. The trace of this lamina is marked on the glass etch tube before the tube is lowered in the hole. The axial lamina that becomes vertical at the survey station is recognized as that axial lamina which contains the long axis of the etch ellipse. The angle between the lamina originally vertical and the lamina vertical at the survey station is thus measurable. When the vertical axial lamina at one survey station has been determined by the etch ellipse at that station, angle R between this lamina and the vertical axial lamina at the next survey station becomes measurable also. By moans of angle R, and dip angles D1 and D2 at the two stations, the change in bearing (z) of the drill hole between the two stations can be calculated."

Aug 1, 1944

By L. H. Adami

This paper reports the results of solution calorimetry conducted to obtain the heats of formation of crystalline FeS04?6.952H20 and FeS04?1.008H20, from. which values were derived for the stoichiometric compounds FeS04?H20 and FeS04?H20. Also included are derived values of the free energies of formation and dehydration. This work was undertaken primarily to fill a need for data for pure, easily obtainable ferrous compounds that are suitable for use as calorimetric intermediates, The ferrous sulfate hydrates meet the essential requirements for this use.

Jan 1, 1963

By L. M. Chan, D. H. Carlson, J. B. Johnson

"Abstract — Concentrations of tailpipe pollutants from diesel-powered. underground mine vehicles change over time due to engine wear and the need for maintenance. Since this deterioration in pollutant emissions may adversely affect the air quality in an underground mine, it should be monitored and controlled. This paper presents decision criteria concerning when to service a mine vehicle diesel engine. These criteria, based on mine air and tailpipe concentration measurements, are designed to maintain the tailpipe concentrations within limits that assure satisfactory mine air quality.Application of the deterioration criteria to mine vehicle emissions involves:establishing, for each pollutant, the allowable deterioration factor, anddetermining the deterioration factor, from the mine air and tailpipe diesel pollutant measurements, and the mine air threshold limit values (TLVs).If the deterioration factor is greater than or equal to the allowable deterioration factor the vehicle is removed from service for maintenance.An analysis applying the criteria to measurements made in an underground coal mine is presented. The tailpipe pollutant concentration data were collected using the Emissions Mea-surement Apparatus (EMA) developed by Michigan Techno-logical University. Since the TLV for diesel particulate matter (DPM) has not yet been established assumed mine air DPMTLVs of 15 and 1.0 mg/m3 were used in the analysis. For all of the diesel haulage vehicles included in the analysis. DPM was found to be the critical pollutant (the one most in need of control). For an assumed mine air DPM TLV of 15 mg/m3 none of the diesel haulage vehicles would he removed from service. However reducing the DPM TLV to 1.0 mg/m3 would make it necessary to remove two of the three vehicles tested from service."

Mar 1, 1992

By J. E. Murphy

Purification of samarium metal by sublimation and by vaporization from a low-melting metal flux, at the same temperature, were compared. Vaporization proved more effective for removing impurities such as magnesium, calcium, and manganese. Recovery of samarium, however, is more rapid by sublimation because of its constant rate of distillation.

Jan 1, 1970

By Andrew Cecala

Miner?s exposure to dust remains a top concern among regulatory agencies, particularly at production facilities with high levels of silica. This respirable dust is present in almost all operations and is a direct cause of the deadly disease silicosis. Silica is one of the most abundant minerals on Earth and is a threat at all operations, especial-ly granite and sand and gravel facilities. The National Institute for Occupational Safety and Health continues to analyze silica?s threat. The institute?s research indicates that heavy-equipment operators have an increased risk to dust exposure, especially when drilling or breaking rock, even when working from an enclosed cab. However, there are methods to reduce an operator?s exposure further, according to recent NIOSH research, which is detailed in its report, Improving Air Quality in Enclosed Caps with Uni-Directional Filtration/ Pressurization System. NIOSH indicates that when surface mining equipment is new, the operator?s dust exposure is normally at accept-able levels. As the equipment ages and components such as gaskets and seals deteriorate, the level of protection can degrade to a point where it is no longer acceptable. However, the institute indicates that at least two critical factors necessary for an effective system.

Jan 1, 2009

By C. J. Johnson, C. J. Bise

"As the US coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity.Room-and-pillar mining accounts for approximately 68% of the nations underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-mid-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.IntroductionThe ultimate goal for any coal mining company is to effectively use its human and financial resources to maximize its profits through the extraction of its reserves. Although recent workforce reductions in the industry have resulted in a more efficient use of labor and increased productivity, there comes a point in time when further reductions in the numbers of workers in each operating section are impossible with existing equipment. For example, Farinelli and Bise (1987) found that labor cost constituted 62% - 73% of the cost per ton of coal at the mining section, with a minimum crew size. Thereafter, efforts to increase productivity must focus on more efficient mine plans and technology.The fact that an increase in productivity can be realized by reducing non-productive time (change-out and tram time) and converting it to productive time has been known and demonstrated for quite some time. What has not been demonstrated frequently is the quantification of the potential productivity increase of currently emerging technology or ""add-on"" equipment. It is one thing to be able to say that a piece of equipment will make an operation more productive, but it is another thing to be able to quantify the productivity increase that will justify the purchase of the new equipment. Not only is a financial benefit possible in room-and-pillar mining with an increase in productivity, but a decrease in the time necessary to develop a longwall panel can also occur.The purpose of this paper is an analyze the impacts of a changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to several scenarios incorporating emerging technology. To do this, four cases will be developed. A base case, consisting of the typical manner in which continuous-miner sections are currently operating, is compared to three layouts incorporating: (1) flooded-bed scrubbers on radio remote-controlled continuous miners, (2)a continuous miner with side-mounted roofbolters, and (3) a continuous miner with side-mounted roofbolters used in conjunction with a continuous-haulage system."

Jan 1, 1989

By W. W. Culter

"This paper is the outcome of thorough investigation into the value of the previous methods used for deriving production decline curves. It is highly important that methods be employed that are fundamentally sound and also practicably applicable. Six methods commonly used were studied. Some of these were found to be fundamentally in error; some save reliable curves but involved much work and time in the preparation; others gave reliable curves with less time and effort.It was found that of the methods previously employed the ""family curve"" method described in Bull. 134 Amer. Inst. Feb. 1918, pp. 499-500 by Lewis and Beal, was probably the most satisfactory. The now method given in this paper ploys the same principles as the ""family curve"" method, but is mathematical instead of graphical,The engineer and the oil man should carefully boar in mind both the use and the limitations of the average production curve such as is derived by the ""family curve"" method or other methods mentioned. Estimations of future productions or of underground oil reserves of a particular tract or well should be made from the production records of the tract or the well itself wherever such records are satisfactory. The use of the average curve of a district or field should be applied only to those properties or wells where there are not sufficient data to construct individual or tract production records, or where the productive life so short that a satisfactory individual record can not be obtained."

Jul 1, 1920

By W. P. Yant, C. E. Traubert

"INTRODUCTION Canister-type gas masks have become an essential part of the equipment of many industries, not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres.Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investi-gations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.TYPES OF CANISTERS EXAMINEDThis investigation included tests of the following types of canisters:(a) Gas-mask canister filled with 725 c.c. of granular activated charcoal, 8 to 14 mesh, and of a quality used in gas masks which meet the Bureau of Mines approval requirements 4 for protection against organic vapors."

Oct 1, 1932

By F. W. Brown

In 1942 the Explosives Division investigated electrostatic hazards associated with the manufacture, storage, and use of explosives. A report was issued in 19454/ presenting the data on the spark sensitivities of explosives. In 1948, the apparatus was redesigned and rebuilt to make the routine testing of explosives safer and more convenient. The rebuilt apparatus is described in this re-issue of the former report. Included are details of construction and a list of parts. PRINCIPLES OF METHOD In normal procedures without special precautions, it is possible for static charges to be accumulated on individuals or on ungrounded equipment or structures.5/ Static charges may be produced in many ways, but they are most commonly produced by rubbing or successive contact and separation of unlike surfaces, at least one of which is usually an insulator.

Jan 1, 1953

By R. R. Sayers

Carbon monoxide poisoning, as usually encountered, is an acute condition resulting from breathing atmospheres containing that gas. It is characterized clinically by headache, dizziness, weakness in the legs, increased respiration at first which later becomes irregular and depressed, collapse, unconciousness, and death; anatomically it is characterized by temporary changes in the red blood cells due to the combination of carbon monoxide with hemoglobin, and, in prolonged severe exposures, degenerative changes in various tissues of the body, especially those of the central nervous system. No race or nationality is immune or has a, special tolerance for carbon monoxide. From data at hand, it is known that both sexes are about equally susceptible. All ages are affected, but small percentages seem to have a more deleterious effect upon young animals and this is possibly true of children. Exercise, high temperature and humidity, and low oxygen content of en atmosphere increase the degree of poisoning for a certain concentration of carbon monoxide. Anything that lowers the physical fitness of a man, such as illness, overwork, or excesses of any kind, exaggerates the effects. More cases of poisoning from carbon monoxide occur in coal mines in the cold months of the year, because explosions take place more frequently during that period, also in homes where gas is used for beating purposes, and in garages from accumulation of automobile exhaust gases due to poor ventilation.

Jan 1, 1923

By Franklin D. Cooper

The value of nonfuel mineral raw materials produced in the United States in 1978 was $20 billion. In 1979, total value increased to an estimated $24 billion, up 20% from 1978. Of the principal metallic ores produced in 1979, about half showed increased quantitative output and all showed increased value per ton compared with that of 1978. Most nonmetallic commodities showed increases in quantitative output and in average value per ton. Because of its decreasing share of the world market, the domestic mineral industry's concerns were the increasing costs of capital, labor, and energy; withdrawals of public lands from mining; and the increasing cost of environmental regulations that tended to deter or delay investment in the Nation's capacity for producing essential minerals.

Jan 1, 1980