Search Documents

By K. E. Hjelmstad

During an underground mine fire, air can be rapidly depleted of oxygen and contaminated with smoke and toxic fire gases. Any delay in warning miners could have disastrous consequences. Unfortunately, present mine fire alarm systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in mine area coverage. Recent research by the U.S. Bureau of Mines has demonstrated that ultra low frequency electromagnetic signaling can be used for an underground mine fire alarm. In field tests of prototype equipment at five mines, electromagnetic signals from 630 to 2,000 Hz were transmitted through mine rock for distances as great as 1,645 m to an intrinsically safe receiver. The prototype system uses off-the-shelf components and state-of-the-art technology to insure high reliability and low cost. When utilized, this. technology would enable simultaneous and instantaneous warning of all underground personnel, regardless of their location or work activity, thereby increasing the likelihood of their successfully escaping a mine disaster. This report presents the theoretical basis for through-the-rock ultra low frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 2010

By John P. Powell, J. L. Eakin

"INTRODUCTION AND SUMMARYNowata County, in the northeast corner of Oklahoma, is one of the principal oil-producing counties of this stripper area. Many fields in the county were opened and much oil was produced before statehood. The location of the major fields, as defined by the Oklahoma Corporation Commission, 2/ the outline of the areas of water-flooding activity, and the location of the several projects described in detail in this report are shown in figure 1.There was some drilling in the county earlier; but it was not until after 1904, when the Secretary of the Interior confirmed as valid the leases granted by the Cherokee Nation, that the major drilling activity began. Initial development in this part of Oklahoma was in the Chelsea field in Rogers County, which adjoins Novata County on the south. The activity spread rapidly northward to the Alluwe and Coody's Bluff fields, and then to the Nowata-Claggett field. Continued exploration resulted in discovery of the Delaware-Childers field, where some wells having an initial production of 1,000 barrels daily were completed. Fields discovered and developed during the next few years included the Lenepah (Elliott), Adair, California Creek, Curl Creek, Woody, and South Coffeyville. The oil-production history of Nowata County is shown in figure 2. In assembling the data for a production curve, it was found that the combined production records for Nowata and Rogers Counties were available for 1914 to 1951, inclusive, and that records for the individual counties were available only from 1926 to 1951, inclusive. The early production figures for the counties from 1905 to 1914, inclusive, except for 1909, were calculated from the initial production statistics of the Federal Geological Survey mineral resources bulletins and production data assembled by C. H. Beal. 3/ The production values for 1905 to 1926 for Nowata County were obtained by dividing the total production for the two counties by a percentage factor derived from known facts regarding the oil industry in the area. Production figures for the individual counties from 1926 to 1933, inclusive, were obtained from the files of the Oil and Gas Journal, and the figures from 1933 through 1951 were obtained from monthly reports of the Oklahoma Corporation Commission."

Jun 1, 1952

By Ann G. Kim

The Bureau of Mines investigated factors that influence the formation of methane and other hydrocarbon gases in coal, which is an integral part of the coalification process. Coalification begins with a biogenetic stage in which plant debris decomposes and peat is formed; methane and CO2 are the predominant gases produced during this stage. During the diagenetic stage of coalification hydrogen and the hydrocarbon gases methane, ethane, ethylene, propane, propylene, butene, iso- and normal butane, and pentane are formed by dissociation of the organic material. Methane may also be produced by a secondary reaction of hydrogen with unsaturates or by the reduction of CO2. The gas contained in coalbeds is a mixture of methane, C2 through C5 alkanes, CO2, 02, N2, H2, and H2; its heating value is equivalent to that of natural gas. The gas content of coal depends on many variables, but an empirical relationship between adsorptive capacity, rank, and depth has been observed.

Jan 1, 1978

By C. R. Stephan, N. B. Greninger, S. J. Luzik

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4- and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 1991

By C. J. Walker

The Bureau of Mines undertook a theoretical and laboratory study to determine the feasibility of using ethylene as a tracer for natural gas in underground gas-storage reservoirs. The study indicated that ethylene was a useful gas tracer in underground gas storages. Tracer losses were not excessive. Laboratory tests were conducted at pressures as high as 500 psia in both wet and dry consolidated-sandstone cores, evaluating tracer loss with gas blends containing natural gas with different concentrations of ethylene tracer. Under certain conditions losses were less than 17 percent.

Jan 1, 1966

By R. W. Freedman

The gas chromatographic method, devised by the Bureau of Mines for analyzing routine mine air samples, was compared with the infrared method used for confirmatory determination of methane in mine air. While maintaining the specificity of the infrared method for methane determination, the gas chromatographic method is more precise, much more rapidly performed, and more convenient.

Jan 1, 1968

By Doris M. Hyde

The petroleum sector continued to dominate Ecuador's economic activity in 1978, accounting for nearly 10% of the gross domestic product (GDP) and 42% of total export earnings. In 1978, a more flexible petroleum export price was adopted which permitted an expansion of foreign market opportunities. During 1979, Ecuador took advantage of disruptions in the world petroleum supply and renegotiated existing export contracts to accomodate the rapidly escalating world market price. Petroleum sales on the spot market were maximized, and prices reached unprecedented levels. By taking royalty payments in-kind, Ecuador increased its volume of petroleum available for term and spot sales. Although the volume remained about the same as in 1978, the total value of 1979 petroleum exports increased to about $920 million, reflecting a 76% increase over the $523 million received for 1978 crude oil exports. Concerned about its steadily decreasing petroleum reserves (recently estimated at about 1.1 billion barrels), rapidly increasing and heavily subsidized domestic consumption, and the prospect of having to import substantial amounts of petroleum by 1983, Ecuador announced plane which it anticipates will double reserves within the next 5 years. The Government plans to spend $1 billion over the 5-year period. Plans include drilling 325 exploration and development wells and establishment of a secondary recovery program for the Sachs and shushufindi fields. Some exploration wells are expected to reach a depth of 17,000 feet. It is thought that substantial reserves exist in the southeast Amazon region. Late in 1979, it was announced that some 10 million hectares will be available for exploration tenders-probably in blocks of about 200,000 hectares each-in the Amazon jungle of the Orients and in the coastal and offshore regions. The Government planned to commission a private, independent analysis of Ecuador's petroleum reserves that would also include recommendations on efficient production levels.

Jan 1, 1981

By McHenry Mosier

Although local conditions at each mining property affect the percentage of increase in drilling speed for a given reduction in gage of bit, the results of drilling tests conducted at the Mount Weather testing adit show such a large advantage in favor of the smaller gages that they should be indicative of the possibilities at most mines. GENERAL DISCUSSION Although it is common knowledge among miners that drilling speed ill- creases with reduction in gage of bit, the large amount o this increase is not so universally realized, A recent Bureau of Mines4/ survey of drilling practices in 28 metal mines showed that the maximum gage of starters is 3 inches and that at 50 percent of the mines starters are 2-1/4 inches or larger, Because this size appears too large for conditions at most' mines where abrasion is moderate and where powder distribution permits, the use of smaller bits presents a favorable opportunity for reducing drilling costs.

Jan 1, 1939

By R. Agarwal

The in-situ stress field was determined, using the overcoring technique, at two underground sites at the Pea Ridge Mine, Sullivan, Missouri. At one of the sites in magnetite, the three dimensional stress field showed the largest principal stress to be compressive (-4564 psi), nearly horizontal and closely parallel to the strike of the orebody. The smallest principal stress was also compressive (-2047 psi) and nearly vertical. Considerable difficulty was experienced in drilling porphyry rock at the second test site in the host rock. Only one hole was drilled at this site. The secondary principal stresses obtained in the porphyry are -9464 and -4945 psi, respectively. The-test site in magnetite is located at a depth of 2505 feet whereas the site in porphyry rock is at 2475 feet. The vertical stresses: due to overburden loading at these sites are -3590 and -2782 psi, respectively. Field determined values of the vertical stress are -2207 and -5098 psi, respectively. The variance; between the two sets of values is most likely attributable to the orebody formation and the differences in the modulii of the host rock and the orebody.

Jan 1, 1977

This Bureau of Mines publication describes the plan used to instrument two longwall gateroads at the Powhatan No. 4 Mine of the Quarto Mining Co. Vibrating wire stressmeters, flat jack U-cells, multipoint extensometer stations, and convergence stations were installed in or on the coal pillars, roof bolts, and roof strata of the gateroad entries. The instruments measure pillar stresses, bolt loadings, and strata movements as the gateroad entries are developed and the longwall panel(s) is mined. The report details only the instrumentation plan of the longwall gateroads and not the evaluation of any subsequent data. This is because a complete analy-sis of the data cannot be made until extraction of the longwall panel(s) is complete.

Jan 1, 1982

By G. W. Birge

The Bureau of Mines investigated the effect of temperature on the mechanical strength of cokes of the type normally used in blast furnace operations. Eight samples of industrially produced cokes were subjected to ASTM tumbler tests at temperatures as high as 1,100° C (2,012° F); these temperatures had no significant effect on tumbler results for cokes with stability indexes of 40.6 to 59.9. Two foundry cokes which were tested at only one elevated temperature (900° C) decreased slightly in tumbler stability. Iron are pellets made from a variety of ores and by various industrial methods were not significantly affected by temperature when tested in an oxidizing atmosphere at 1,000° C (1,832° F) by the tentative standard ASTM method.

Jan 1, 1966

By Merle Randall

Application of a new chemical spray in a mercury mine in which ore rich in native metal was causing salivation among the miners has given such favorable results that it is believed the process will be useful in other mines and perhaps in some plants where similar conditions exist. The process was originated by Merle Randall, professor of chemistry at the University of California. GENERAL PROBLEM The presence of native quicksilver in mines from which the metal is produced has long been a source of trouble and danger to the workers. Men have been sickened and some of them have been disabled by exposure to the vapors present (even in workings that were well-ventilated by ordinary standards) and to contact with dust, dirt, and moisture with which the finely divided quicksilver was mixed. Where the ore was rich and this exposure was considerable men were able to work only a few days or weeks; where the exposure was less they were weakened and subject to ailments often attributed to other causes.

Jan 1, 1942

By R. C. Wang

Solid-liquid flow in different pipe geometries was investigated. This investigation was conducted by measuring delivered solids concentration and head loss. The delivered solids concentration was measured to study the effect of pipe geometry on the minimum carrying velocity above which solids do not lag behind the fluid. Head loss was measured to study the effect of pipe geometry on the friction loss. A mathematical formula was developed for determination of the minimum carrying velocity. Darcy-Weisbach's equation and Durand's equation were used for comparison of head losses of pipe shapes. Of the different pipe shapes studied, each having the same interior cross-sectional area, the rectangular pipe with the wide side oriented as the base yielded the lowest minimum carrying velocity at high solids concentrations. The minimum head loss at low velocity and high solids concentration also was attained with this pipe. Although the circular section is known to be the best for transporting liquid only, the present study suggested that pipe geometry is a factor in lowering the operating velocity and reducing head loss in solid-liquid flow.

Jan 1, 1973

By J. C. Franklin

A 32-channel continuous monitoring system has been developed to monitor radiation working level (WL), fan operation, and air door position. The system consists of a surface receiver unit and an underground transmitter that is connected to the various monitors. A continuous WL monitor used with the system can generate alarms at two different WL readings. One of these levels is variable from 0.00 to 0.99 WL and generates an alarm on the surface receiver. The other level, fixed at 1.0 WL, generates an underground alarm in the vicinity of the monitor. The detectors for fan operation and air door position work on the principle of a completed circuit to the underground transmitter (multiplexer). When the circuit is broken, as is the case when a fan is off or an air door is open, an alarm is generated at the surface receiver. This alarm remains in effect until the circuit is completed, signifying the fan has been turned on or the air door has been closed.

Jan 1, 1982

By G. S. Rice, H. P. Greenwald, H. C. Howarth

"Stoppings in coal mines serve, important and. vital functions, such as coursing the ventilating current, sealing off abandoned or dangerous workings, sealing fire areas, and separating mines at boundaries. Stoppings may hold back water, but normally that is not their function; their design is, or should be very different from that of a hydraulic dap which is designed to a definite load, often a very heavy one, from one direction over an indefinitely long period. Hence, a dam usually requires an arched structure to resist hydraulic pressure, and it must be massive to meet vertical stresses due to heavy ground pressure.Stoppings are designed primarily to resist a pressure applied laterally through air or gases. Their strength cannot be stated without specifying the direction of applied load. A stopping may be placed in stress by proof pressure subsequent to erection, through extraction of pillars in the vicinity which may act direct, or by squeezing the ribs or heaving the floor. These forces act more or less parallel to the faces of the stopping and may be very great but measures must be taken suitable to each case, and it is impossible to allow for these in general specifications other than to call for normally good construction. A stopping is principally designed to resist the action of forces at right angles to its face, such as the shocks of blasting, the pressure of gas from instantaneous violent out bursts such as have occurred in certain British Columbia coal mines, sudden compression of the air by great falls of roof in closed spaces, and at time pressures that accompany an explosion of either fire damp or coal dust or both. This paper deals with the tests of pressures of explosions only."

Sep 1, 1930

By George S. Rice

A novel method of extinguishing a mine fire in a stowed or gob-filled area by employing liquid carbon dioxide under high pressure eras used recently with success at the President (Prasident) coal mine, Bochum, Germany, as reported by P. Cabolet in Gluckauf (Apr. 24, 1937, p. 393) The use of carbon dioxide gas as a fire-fighting agent in surface plants and in ships is now general practice in the United. States, but when it has been tried for extinguishing fires in mines in large areas more or less confined by stoppings it has not been successful. Examples of the latter method of attempting to fight mine fires are given in Bureau of Mines Bulletin 229, Fifty-Nine Coal-Mine Fires; How They Were Fought and That They Teach, by G. S. Rice, J. VT. Paul, and 14. VT. von Bernewitz (1927). The reason for its nonsuccess may be either that the stoppings are not tight or that the roof and pillars are more or less fissured and enough air passes into the area to sustain a slow fire, whether of spontaneous origin or produced by gas explosion or other source of ignition.

Jan 1, 1937

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

The Federal Coal Mine Health and Safety Act of 1969 has dictated major changes in mine ventilation with regard to both air quantity and quality. Requirements have also been placed on the ventilation of beltlines, gob and face areas, and air velocities on trolley haulage roads are limited. Escapeways, separate from trolley haulage roads and on an intake split of air, must be maintained continuous to the surface. These and other similar requirements have not only precipitated several modifications to existing ventilation systems but also have greatly increased the complexities of new mine ventilation planning. It is apparent that the use of computers in ventilation system analysis and design is a necessity. SUMMARY Although computer oriented analysis of mine ventilation systems was introduced over two decades ago, it has yet to receive widespread acceptance in the United States. Central to this problem is the fact that, while many computer programs for network analysis have been developed, no attention has been paid to the development of computer input data. Consequently, without this foundation, program applications have been infrequent. This thesis has directly attacked this problem and has presented all pertinent information basic to the development of good computer input data. The areas that were covered include quantity measurement, pressure measurement, fan testing, survey data balancing, and the development of a network schematic from the ventilation survey results. These discussions on data collection and the corresponding reduction to computer coding have been illustrated by an application of a ventilation simulation program to an existing mine in Southwestern Pennsylvania. The use of a ventilation

Jan 1, 1977

By George W. Hezzelwood

This paper describing the minim, methods at the mine of the Consolidated Cortez Silver Mines, Cortez, Nevada, is one of a series of similar papers being prepared by the Bureau of Mines on mining practices and costs in the various mining districts of the United States. The Cortez district is situated on the southwest slope of Mt. Tenabo of the Cortez Range, near the middle of the boundary line between Eureka and Lander Counties (fig. 1). The camp of Cortez is 36 miles south of Beowawe, the nearest station on the Southern Pacific and Western Pacific Railroads. Mt. Tenabo, which is the highest summit of the south end of the Cortez mange, has an elevation of 9,240 feet; Cortez is about 6,280 feet above sea level. The Consolidated Cortez Silver Mines is the only company operating in the district at the present time and employs about 60 men. The daily production of l25 tons of silver-lead ore is concentrated in the company's mill of 150 tons capacity. The concentrate is hauled to Beowawe by automobile trucks for shipment to a reduction plant in Salt Lake Valley, Utah.

Jan 1, 1930

By A. May

Florida has accumulated about 400 million tons of phosphogypsum, a mineral process waste generated in the production of fertilizer, and is adding 30 million tons to this annually. To minimize storage of this waste and reduce potential environmental effects, the Bureau of Mines conducted research into utilizing the phosphogypsum, by identifying and developing high-volume uses for this material. Admixtures of phosphogypsum, fly ash, and lime that could produce a coarse aggregate suitable for road construction were investigated. Using phosphogypsum with asphalt, cement, cement-kiln dust, silica, clays, and oxychlorides to pro-duce aggregate was also examined.

Jan 1, 1985

By J. Weinberg

This Bureau of Mines report presents data on the changes in the use of steel in motor vehicles over the past 35 yr. Sources of supply of steel for the automotive sector have shifted from almost all domestic in the 1950's to about 50% domestic and 50% foreign in the 1980's. Downsizing, design changes, and substitution of lighter weight materials to achieve energy efficiency also contributed to the market loss of the domestic steel industry. Although plastics and aluminum have displaced some steel in motor vehicles over the years, heavy low-carbon steel is now being replaced most rapidly by lightweight high-strength steel. If the percent of domestic steel used in motor vehicles had not declined since 1950, domestic industry would have supplied 9.3 million more short tons of steel than it supplied in 1985. Downsizing and design changes accounted for 43% of the loss; steel imports, 32%; and substitution of plastics and aluminum, 25%. In 1985, the total value of market share lost by U.S. steel producers was $5.1 billion, of which $1.6 billion was lost to foreign steel producers and automobile manufacturers. Through aggressive marketing and increased efficiency, however, the domestic steel industry may be able to recapture some lost markets, as applications for high-strength steels expand, and as foreign-owned automotive plants in the United States provide fresh sales opportunities.

Jan 1, 1988