Search Documents

By W. D. Musgrove, B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Cahaba coal field is the second largest coal—producing area in Alabama. This field underlies parts of Shelby, Jefferson, St. Clair, and Bibb Counties and has an area of about 270 square miles. The Cahaba formations contain a number of coal beds, about 8 of which are mined at present. Although the area contains many folds and faults, samples from various mines and beds indicate that, except for the variation in ash content, the coal from this field is very uniform in character and quality. It is a high-volatile bituminous coal used chiefly for steam-raising purposes and domestic fuel. The coal as mined usually contains too high a percentage of impurities to be marketed without some preparation. The majority of the mines have washing plants in which jigs are the favorite type of equipment, although at some mines tables are used for cleaning the slack sizes. The washing characteristics of the coal from the Cahaba field are very uniform and differ from those of the near-by Warrior field, in that the coarser sizes contain a much lower percentage of bony material than the finer sizes. In general, the bone increases with decrease in size. It breaks into thin flakes, making difficult its elimination in the cleaning process, and gives rise to what is known among the washery operators of the Cahaba field as the ""rash problem.""A previous publication 5 referred to rash from the standpoint of jig operation and suggested some means of handling it with jigs. This report presents the results of table tests on two samples of fine coal from the Thompson and Woodstock beds, respectively, of the Cahaba field to determine the influence of rash on table efficiency.This investigation has been made in connection with the study of coal-washing problems now being conducted by the U.S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators of Alabama."

May 1, 1934

By J. E. Wilson

The Pittsburgh carbonization laboratory of the Bureau of Mines has determined the expansion or contraction of more than 300 coking coals in a modified Bethlehem-type sole-heated expansion tester. Information on the actions of coals or blends of coals when coked is extremely valuable to operators of commercial-scale coke ovens. Coals that expand abnormally or beyond expectations can cause extensive damage to coke ovens and result in costly shutdowns and repairs. Although test results for many of the coals have been given in various Bureau of Mines publications, considerable information was not published. Thus, it is the purpose of this report to furnish coal operators and the coking industry with a current appraisal of the expanding properties of all coals tested by the Bureau before September 1, 1958. These data should be useful in the normal long range planning of coal and coke production and will be essential if the demand for coking coals increases abnormally or when reserves of higher grade coals are depleted.

Jan 1, 1959

By A. D. Hahn

The Federal Bureau of Mines examined ilmenite-bearing sands in southern Texas as part of a program to discover sources of supply for the domestic titanium industry. Deposits were examined from May 1956 through January 1959 in the outcrops of sandstone beds in the Jackson group of Eocene formations in Lee, Burleson, Fayette, and Starr Counties on the Gulf Coastal Plain; in alluvial valley fill in Brewster County in southwest Texas; in the sand beaches of Matagorda Peninsula and the Galveston, Padre, and Brazos Islands--part of the offshore chain of barrier islands along the Texas coast; and in unconsolidated sediments in Willacy County on the Rio Grande delta in the southeast Texas.

Jan 1, 1961

By Loren R. Anderson

This is an Appendix of Volume I. It contains the results of the electric cone penetrometer soundings from the first phase of the testing program.

Jan 1, 1982

By J. G. Donaldson

Cobalt-tungsten binary deposits were formed in laboratory experiments by hydrogen reduction of the anhydrous mixed vapors of cobaltous chloride and tungsten hexachloride. The materials were sublimed in seperately heated zones of reaction tube and were transported in a stream of purified helium into the deposition section of the tube where the chloride gases were reduced to metal by a countercurrent flow of hydrogen. Heattreating of the near stoichiometric binary metallic deposits converted nearly all to the intermetallic compound Co3W, however, small quantities of both cobalt and tungsten remained. Mechanical tests showed that the tensile strength of heat-treated 75 percent cobalt-25 percent tungsten deposits was twice as high as that of similarly treated deposits of cobalt.

Jan 1, 1965

By L. C. IlsLey

Through the cooperation of the Pennsylvania Department of Mines the writer obtained from State, records detailed information concerning coal-mine accidents occurring in Pennsylvania bituminous mines during 1939, particularly those nonfatal accidents in which the injured person lost 60 or more days? time from mark. The writer wishes to acknowledge assistance received from Pennsylvania State officials, especially Richard Maize, secretary of mines, and. Joseph J, Walsh, deputy secretary of mines; also to Thomas Dickinson,3/ of the Bureau of Mines, who rendered valuable assistance in assembling the data an the several tables.

Jan 1, 1941

By Phillip N. Yasnowsky

This Bureau of Mines report examines the percentage depletion allowance rate structure in relation to several criteria that are indicative of U.S. mineral import dependence. These criteria are the minerals considered as strategic and critical for stockpiling purposes, the ratio of reserves to forecast cumulative demand (1976-2000) for selected minerals, and the U.S. net import reliance as a percentage of apparent consumption (1978), also for selected minerals in general, it was Found that there does exist a direct, although not perfect, relationship between the percentage depletion allowance rates and the degree of import dependence as indicated by these three criteria. The higher percentage rates tend to he associated with those minerals for which the United States is, or will likely he, heavily dependent on foreign sources. In addition, a basic discussion of the mineral depletion allowance is provided, including numerical examples illustrating the computation of the allowance under several assumptions. Also, the percentage depletion allowance rates for individual minerals are tabulated.

Jan 1, 1980

By Jr. Karr

The Bureau of Mines studied the influence of carbonization method, temperature, and carrier gas on the composition of eight different low-temperature tars produced from a Colorado subbituminous coal. A fluidized bed was compared with an entrained bed, temperature was varied from 500° C to 650° C, and external heating using recycle gas as the carrier gas was compared with internal heating using oxygen-containing gas. The entrained bed yielded significantly more m-cresol and m-ethylphenol, indicating that thermodynamic equilibrium was more nearly approached in the system. Increasing the temperature greatly increased the yield of benzenes and naphthalenes, while paraffins, olefins, and total tar acids were reduced. Using oxygen in the carrier gas decreased the yield of low-boiling phenols and increased that of paraffins and olefins at 650° C.

Jan 1, 1966

By W. L. Crentz

The Black Mesa coal field is part of the Hopi and Navajo Indian Reservation in Apache, Navajo, and Coconino Counties, Ariz. The field is in an isolated area with the nearest railroad 70 to 90 miles to the south. Travel is restricted by roads that become impassable during inclement weather. The area is a mesa and rises from 500 to 2,000 feet above the surrounding territory. Water is very scarce, and the nearest stream of any consequence is the Colorado River about 90 miles northwest from the center of the field. Coal beds are found in the Mesaverde formation of the Cretaceous age, but they are uncorrelated and range from subbituminous to bituminous in rank. Huddle2/ estimates the reserves of subbituminous coal in Arizona at about 15 billion tons, most of which is in the Black Mesa field. The geology of the field has been reported by Campbell and Gregory.3/ Coal production is small, and the output is used almost exclusively for domestic fuel in the Indian schools, missions, and trading posts.

Jan 1, 1955

By L. J. Kane

Applications are described of various methods for determining the weight concentration and physical properties of solid and liquid impurities of gases in connection with problems encountered in synthesis-gas production. Of special interest among these methods may be listed: 1. A method developed for determining, the weight concentration of solid and liquid impurities in. hot, crude synthesis gas containing a high concentration of moisture. 2. A method developed for the same purpose but for highly purified synthesis gas or atmospheric air. 3. A method for obtaining a uniform dispersion of dry duet or, a microscope slide for particle-size determination or other purposes.

Jan 1, 1954

By S. H. Lorain

Shortly after the Strategic Minerals Act of 1939 we passed by Congress, the Bureau of Mines was authorized to begin a program of investigation of domestic sources of strategic minerals. Since World War I, the Philipsburg district had been virtually the only one in the United States that was producing manganese on a commercial scale. Consequently, the district was among the first to he investigated. During the summer of 1939, the Geological Survey mapped the geology and ore deposits of the district. In late July 1939 the writer examined the district for the Bureau of Mines. On the basis of this examination and of the work performed by the Geological Survey, the Bureau of Mines diamond-drilled at several properties in the district during the summer of 1940. This report reviews the mining history and geology of the district, and presents the factual data obtained by diamond drilling.

Jan 1, 1950

By R. R. Wells

As a part of the strategic minerals program of the Bureau of Mines, nine chromite-ore samples were obtained during the period 1949-56 from mines in the vicinity of Red Mountain, near Seldovia, Kenai Peninsula, Alaska. This report summarizes the results of beneficiation studies of the samples at the Bureau's Juneau, Alaska, and Albany, Oreg., laboratories. In general, the ores were found amenable to concentration by gravity methods for producing concentrates that assayed over 48 percent chromic oxide. Intimate association of chromite and gangue minerals, however, necessitated fine grinding and limited the amount of chromite recoverable. Recovery of chromium in concentrate that assayed 48 percent chromic oxide or higher ranged from approximately 20 percent for low-grade ores (10 to 12 percent Cr203) to more than 95 percent for 1 high-grade sample (42 percent Cr203). The iron content of the chrome-bearing mineral -hence, the chrome/iron ratio of finished concentrate -appears to vary with the grade of the ore. Concentrates made from high-grade ores had chrome/iron ratios as high as 3.1:1; the concentrates from low-grade ores, however, had chrome/iron ratios as low as 1.8:1.

Jan 1, 1957

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1956 was made under a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 120 samples of aviation gasoline and for 38 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers' 1956 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 17 producers of aviation jet fuels are represented.

Jan 1, 1957

By I. F. Avery

The productive capacity of natural gasoline and cycling plants in the United States on January 1, 1956, was 46.4 million gallons per day, according to the Bureau of Mines r biennial survey. This represented an increase of 7.5 million gallons per day during the 2-year period since the last survey. In the previous 2-year period, capacity had increased 4.8 million gallons per day. The total number of plants increased from 535 on January 1, 1954, to 600 on January 1, 1956. The number of operating plants increased from 521 to 571. The major increases in capacity took place in Texas, Louisiana, New Mexico, and Oklahoma, with the absorption-type plants continuing to account for most of the new construction. All types of plants showed construction gains with the exception of charcoal which showed no change.

Jan 1, 1957

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-million-standard-cubic-foot-per-day, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 million tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the terms of the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment varies: $65,137,900 for the 4.8-million-ton-per-year (MM tpy) mine in the Eastern province, $78,514,600 for the 6.72-MM-tpy mine in the Interior province, and $42,050,100 for the 9.2-MM-tpy mine in the Northern Great Plains province. Total capital investments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $86,969,900, $109,378,500, and $78,543,500, respectively. Corresponding selling prices for the coal, per ton, are $6.94, $6.03, and $3.39, assuming a 15-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1976

By D. A. Reynolds, J. D. Davis

During early development of the blast furnace, Connellsville coke made entirely from Pittsburgh-bed coal proved to be an excellent fuel. The need for blending coking coals arose as the industry grew and it became necessary to carbonize coals having voking properties inferior to those of Pittsburgh coal Most coals carbonized today in continental Europe and this country are blonded: This practise has improved the quality of coke and permitted the utilization of coals that would yield inferior coke, if carbonized sepa- rately, The depletion of the world's better coking coals, which has been noted by leading coal technologists,2/4/wes accelerated during the recent war and. It is important, therefore, that reserves be evaluated and conserved. In the principal, steel-producing sections of this country, Pocahontas coals have been blended so extensively that the terms "low-volatile coking coal": and. "Pocahontas" have become virtually synonymous. Other low-volatile coals. have been used to manufacture metallurgical coke and will be used more extensively as, the supply of the better known and more accessible Pocahontas coals decreases. Recognizing the need for augmenting the supply of high-rank coking coals, the Bureau of Mines has included both low- and medium-volatile coals in its Survey of the Carbonizing Properties of American Coals, which was started with the cooperation of the American Gas Association in 1929. Twenty coals, 12 of low-volatile and 8 of medium-volatile rank, have been blended with high-volatile A Pittsburgh-bed coal, and five standard low- volatile coals have been blended with various high-volatile coals. Most of the results of carbonization tests of these coals and their blends have been

May 1, 1946

By Boyd Guthrie

The current use of Mid - Continent crude oil for the manufacture of war products , such as aviation gasoline and lubricating cil , has caused an acute shortage of available supply from established sources . Therefore , refiners who heretofore have had no reason to use West Texas crude oils now are considering them as charging stock and need more information concerning their characteristics . The Bureau of Mines has published several reports3/ giving analyses of the most important of these crude oils . However, to make the applicable data in these publications readily available to refiners , the present compilation of analyses of West Texas crude oils has been prepared . Data showing the effect of catalytic desulfurization of naphthas from West Texas crude oils have been presented in a restricted Bureau of Mines Report of Investigations . These analyses were made under the general supervision of R. A. Cattell , chief, Petroleum and Natural Gas Division, Bureau of Mines , Washington, D. C. , and N. A. C. Smith, supervising engineer , Fetroleum Experiment Station, Bureau of Mines , Bartlesville, Okla . , and under the direct supervision of Harold M. Smith, senior petroleum chemist, Bartlesville , Okla .

Jan 1, 1944

By William Cochran

Data on the cost and quantity available were developed for rutile (TiO2), which is potentially recoverable as a byproduct at sand-washing plants in the Southeastern States of Alabama, Georgia, North Carolina, and South Carolina. Baaed on 1969 production data, an estimated 4,300 tons of rutile could be recovered annually from plants that process more than 25,000 tons of sand per year. Rutile prices at which this resource would be available ranged upward from $262 per ton, compared with the current market value of $185 per ton.

Jan 1, 1972

By Thomas Fraser, William L. Crentz

"INTRODUCTION Sulfur is a most damaging impurity in many of our American coals. From the older coal industry of Europe and Britain we can apparently learn but little about the problem of preparing and using high-sulfur coal. Although washing has long been established there for controlling ash content, sulfur is referred to rarely, as the important deposits are singularly low in sulfur.On the other hand, widely distributed coal deposits of America differ tremendously in sulfur content. Many of the more extensive beds contain too much sulfur for metallurgical use, and almost everywhere except in the Rocky Mountain and Pacific coast regions sulfur control is at least a potential problem. American coal-preparation engineers are confronted not only with great variations in the total quantity of sulfur in coal but with an intricately varying pattern of the physical and chemical forms in which the sulfur occurs. It must be conceded that the baffling problem of sulfur reduction in coal is as yet substantially unsolved, for there are but few isolated instances in which we have been able to prepare a satisfactory metallurgical fuel from coals containing as much as 2.0 percent sulfur in the raw state.It has been assumed generally that organic sulfur, being chemically combined with carbonaceous matter, is distributed throughout the coal matter and that it remains unchanged in the clean-coal part of the product during washing.Sulfur that may be washed out of the coal is that part that is combined with the iron in pyrite lenticles associated with the coal. In most of our coals it has been found that, besides the visible bands, lenses, and flakes of pyrite, extremely small and even microscopic particles of pyrite 4/ are distributed through the coal matter. Only the free, relatively coarse pyrite particles .are removed by conventional coal-washing devices, and usually most of the sulfur is still left in the product."

Dec 1, 1947

By B. A. Rogers

The problem of obtaining enough manganese for use in the manufacture of steel appears likely to recur when international relationships are disturbed and to become serious at any time when the United States is cut off from its customary supply. Some idea of the problems that an e under war conditions may be obtained from a description given by Ellicott3/ in 1918 before the American Iron and Steel Institute. This condition arises because in normal times there is an economic advantage in importing available high-grade foreign ores to the neglect of our own less satisfactory resources. That considerable low-grade manganese ore and a much smaller amount of high-grade material are available in this country is well known from geological surveys 4/ and has been confirmed by Bureau of Mines investigations. Locations of the various deposits are indicated in figure 1. The possibility of greatly expanding domestic production was actually demonstrated from 1913 to 1918, when the annual production of manganese from domestic ores rose from about 4 percent to approximately 35 percent 6/7/ of the total consumption of ferromanganese and spiegeleisen. In idea of how domestic production compares with total consumption in the United States can be obtained 1 from figure 2, taken from the Minerals Yearbook8/ for 1970. Assuming that it is possible to increase production of manganese ores sufficiently to supply all our needs, such a program presumably would require 2 or 3 years, and the cost of production would certainly rice considerably, for some time at least. For

Jan 1, 1941