Search Documents

By E. G. Noble

The effects of HBr concentration and temperature on the solubility and hydration state of AlBr3,' CoBr2, PbBr2, MnBr2, KBr, and NaBr were investigated by the Bureau of Mines. Saturated aqueous solutions of the AI, Pb, K, and Na bromides were sparged with HBr gas at 20°, 40°, and 60° C, and saturated solutions of Co and Mn bromides were sparged at 20° C. Increased HBr concentration caused decreased salt solubility because of the common ion effect for all the investigated bromides except PbBr2. Aqueous solubilities at 20° C were, in percent, 51.7 for AlBr3, 53.2 for CoBr2, 1.1 for PbBr2, 59.6 for MnBr2' 39.5 for KBr, and 47.4 for NaBr. At 60° C, the solubilities were, in percent, 53.3 for AlBr3, 2.2 for PbBr2' 46.0 for KBr, and 53.8 for NaBr. Solubilities in solutions sparged to HBr saturation at 20° C were, in percent, 0.5 for AlBr3, 42.0 for CoBr2, 32.2 for PbBr2, 21.0 for MnBr2, 0.6 for KBr, and 0.3 for NaBr. At 60° C, the solubilities at HBr saturation were, in percent, 1.8 for AlBr3, 41.4 for PbBr2, 1.3 for KBr, and 0.4 for NaBr. CoBr2 precipitated out to a minimum solubility of 27.2 pct at 28.7-pct-HBr concentration. Further increases in HBr concentration increased CoBr2 solubility because of the formation of bromide complexes. PbBr2 in-creased in solubility as HBr concentration increased.

Jan 1, 1988

By D. B. Taliaferro

Information regarding the pores or voids in reservoir rocks is vitally important in the scientific extraction of petroleum from natural underground reservoirs, and petroleum technologists concerned, with subsurface, conditions have devised various methods that give reasonably accurate information as to the porosities of oil and gas-bearing sands.5/ In this, work, several investigators have made use of the experience of the ceramic and other industries. The method of determining the effective porosity of oil sands described in this report falls within the general classification of gas-expansion methods. It was devised and developed at the United States Bureau of Mines Petroleum Experiment Station, Bartlesville, Okla., as a part of the research dealing with fluid and energy relations in reservoirs and improved oil-recovery methods. The apparatus and procedure are well adapted to the requirements of the Bureau, and the following detailed description has been prepared so that others may make use of the information. A tabulation at the end of the report gives the results of several hundred porosity determinations for oil sands in fields of 11 States.

Jan 1, 1937

By D. B. Taliaferro

Information regarding the pores or voids in reservoir rocks is vitally important in the scientific extraction of petroleum from natural underground reservoirs, and petroleum technologists concerned. with subsurface conditions have devised various methods that give reasonably accurate information as to the porosities of oil and gas-bearing sands.5/ In this work, several investigators have made use of the experience of the ceramic and other industries. The method of determining the effective porosity of oil sands described in this report falls within the general classification of gas-expansion methods. It was devised and developed at the United States Bureau of Mines Petroleum Experiment Station, Bartlesville, Okla., as a part of the research dealing with fluid and energy relations in reservoirs and improved oil-recovery methods. The apparatus and procedure are well adapted to the requirements of the Bureau, and the following detailed description has been prepared so that others may make use of the information. A tabulation at the end of the report gives the results of several hundred porosity determinations for oil sands in fields of 11 States.

Jan 1, 1937

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute of Occupational Safety and Health recently performed a laboratory study to evaluate which factors on an enclosed-cab filtration system are most significant. The various factors evaluated were intake filter efficiency, intake air leakage, intake filter loading, wind infiltration, use of a recirculation filter, and the use of an intake pressurization fan. The result of this laboratory testing has shown that the two most important factors for an effective filtration system on an enclosed cab were the efficiency of the intake filter and the use of a recirculation filter. A higher-efficiency intake filter considerably increased the quality of the intake air that was delivered into the enclosed cab. It also was determined that air leakage around the intake filter notice-ably reduced its air cleaning effectiveness. The second key factor is the use of a recirculation filter, which was shown to improve the air quality in the enclosed cab by six to 12.7 times more than the intake filter alone. The reason for the significant improvement was that the cab air was constantly drawn through the recirculation filter, thus continually filtering the dust out of the air.

Jan 1, 2010

By Foster Fraas

This Bureau of Mines report describes a method for separating minerals at magnetic susceptibilities within the diamagnetic susceptibility range. The maximum feed rate varies directly with the square root of the lower limit of permissible susceptibility, while the lower limit of permissible susceptibility varies inversely as the square of the magnetic field strength. Minerals may be separated at particle sizes smaller than possible on conventional dry-type magnetic separators.

Jan 1, 1969

By Peter D. Lohn

The Bureau of Mines conducted both laboratory and field investigations to study the effectiveness of medium-pressure (up to 30,000 psi) water jets in controlling the generation of airborne respirable dust during the hydraulic fragmentation of coal. Laboratory studies were conducted at the Farmington High Energy Test Site of the Twin Cities Mining Research Center, and field studies were carried out at the Humphrey No. 7 mine, Mount Morris, Pa., in the Pittsburgh coalbed. The water jets were produced by commercially available triplex pumps. The dust samples were collected by midget impinger samplers, and analyzed by electronic and optical counting techniques. Respirable dust concentration for a full-scale production model was projected at below 2 mg/m3, the maximum exposure allowed by the Federal Coal Mine Health and Safety Act of 1969.

Jan 1, 1975

By Eric R. Bauer

This Bureau of Mines publication describes and illustrates the physical signs of excessive loading on mine roof supports, installations, and openings. It is designed to assist mine personnel in recognizing potentially hazardous ground conditions, by emphasizing the preliminary effects of developing unstable ground. Increased worker awareness can be expected to reduce the injuries and fatalities resulting from falls of roof, rib, and face.

Jan 1, 1985

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation 1 of a coal mine. The average thickness of coal seams mined in the United States decreased 2 inches between 1950 and 1955 to an average of 62 inches, which also is 3 inches less than the 65 inches in 1945. The decrease in thickness is due partly to the increased production from strip mines with thinner seams and partly to the increased percentage of total production at underground mines in certain States having thinner seams. The thickness of seams at auger mines was measured for the first time in 1955 and was 53 inches. Though bituminous coal and lignite is mined today from seams of exceedingly variable thickness -less than 2 feet to ore than 50 feet -a large majority of the production, 65 percent in 1955, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1957

By H. Dolezal

A laboratory study of acid-ferrous sulfate treatment of low-grade manganese ores from the Cuyuna range, Minnesota resulted in 93-percent extraction of manganese as manganese sulfate with consumption of 3.8 pounds of H2S04 per pound of extracted manganese. Two types of ore were treated in consecutive stages. The first are contained carbonate minerals of manganese and iron, both soluble in H2S04 solution. The second ore contained manganese oxide minerals, insoluble in straight acid solution but soluble in the ferrous sulfate solution obtained from treating the first ore. Leaching data were obtained by countercurrent percolation of coarse (minus-1/2-inch) ore particles at room temperature and by agitating minus-65-mesh ore particles in heated solution. Extraction of manganese and acid consumption were the same, but the percolation leach required 6 days compared with 1 hour for hot agitation. Variations in the size of ore particles treated, leaching time, acid concentration, solution temperatures, and method of applying ferrous sulfate solution to the oxide ore were studied. The effects of several reagents for removing iron from solution and improving filtration were also studied.

Jan 1, 1959

By Thomas C. Mowatt

Chemical and petrographic studies were carried out on selected tin-bearing rock samples of contact-metasomatic origin from the Cassiterite Creek and Brooks Mountain areas, Seward Peninsula, Alaska. The tin content of rocks ranged from 0.39 to 8.9 pct. Leaching with a 20 pct hydrochloric acid solution released from 19.3 to 67.9 pct of the tin. Cassiterite was not observed in the rock samples. These results are significant with regard to tin recovery and reserve delineation in these and similar occurrences. Part of this leachable tin may be associated with metasomatic borate minerals.

Jan 1, 2011

By J. Hamilton Duffy

This is the first of, a series of papers describing dredging methods and costs in recovering sand and gravel from the beds of rivers throughout the United States and deals directly with the methods employed and costs obtained by the Ohio River Sand Co. near Louisville, Ky. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. R. Thoenen, mining engineer of the Bureau of Mines, in the collection of data and compilation of this report.

Jan 1, 1931

By C. Harry Benedict

This paper presents the details of milling practice and costs at the conglomerate mill of the Calumet & Hecla Consolidated Copper Co., Lake Linden, Mich., and is one of a series on milling methods being published by the Bureau of Mines. GENERAL DESCRIPTION The mines of the Calumet & Hecla. Consolidated Copper Co. are located in the Keweenaw Peninsula of northern Michigan. The mines of this district lie in a belt not over 4 miles wide and 100 miles long, which contains more or lees commercial ore. The Calumet & Hecla properties are the farthest north, except for the Seneca, of the operating mines. The district borders on Lake Superior, and by means of the Portage and Torch Lake waterways the largest lane vessels, can transport coal and other supplies from the lower Lakes directly to the company docks.

Jan 1, 1930

By G. F. Friel

A series of experiments in the U.S. Bureau of Mines Safety Research Coal Mine at the Pittsburgh Research Center evaluated the effects of crosscuts on the travel time of carbon monoxide (CO) along an entry to improve the accuracy of a mine-fire locator program. Three entries, ten single crosscuts, and three double crosscuts were instrumented with CO sensors. One-percent CO in nitrogen was released and monitored as it traveled the entries. In addition to dispersion of CO at the front of the CO wave, CO was entrained from the entry into the crosscuts. It was determined for an entry and single-crosscut configuration that the measured travel time for a concentration change of 5 ppm was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and crosscut volumes. For an entry and double-crosscut configuration, the measured travel time for the same concentration change was 25% greater than the predicted time based upon entry volume only, but 10% less than the predicted time based upon entry and crosscut volumes. An effective dispersion coefficient for CO dispersion along one of the entries was estimated to be 1.5 m2/ s.

Jan 1, 2010

By Robert M. Cox

The U. S. Bureau of Mines (USBM) MULSIM/NL modeling technique has been used to analyze anticipated stress distributions for a proposed alternative longwall gate road design for a western Colorado coal mine. The model analyses indicated that the alternative gate road design would reduce stresses in the tailgate entry without increasing stresses in the headgate entry. To test the validity of the alternative gate road design under actual mining conditions, a test section of the alternative system was incorporated into a subsequent set of gate roads developed at the mine. The alternative gate road test section was instrumented with borehole pressure cells, as part of an ongoing USBM research project, to monitor ground pressure changes as longwall mining progressed. During the excavation of the adjacent longwall panels, the behavior of the alternative gate road system was monitored continuously using the USBM computer-assisted Ground Control Management System. During these field tests, the alternative gate road system was first monitored and evaluated as a headgate, and later monitored and evaluated as a tailgate. The results of the field tests confirmed the validity of using the MULSIM/NL modeling technique to evaluate mine designs.

Jan 1, 2010

By Edward D. Thimons

Inflatable stoppings are currently marketed for production use, and numerous mining companies have become interested in using such stoppings in rescue and recovery operations. The Bureau of Mines therefore evaluated the concept of using inflatable stoppings in emergency situations. The stoppings tested by the Bureau were 12-foot-diameter spheres inflated with a blower operated by a small battery pack. Experiments were conducted with the stoppings in a full-scale wooden mine model to evaluate their ability to withstand sliding or slipping at various internal and differential pressures, puncture resistance, various inflation techniques; and internal leakage from the stoppings. The stoppings were then installed and tested in the Bureau's Safety Research Coal Mine at Bruceton, Pa., to determine their effectiveness as mine air barriers. Despite some encouraging results obtained with the model and in-mine studies, the stoppings did not perform well in two operating metal mines where they proved difficult to erect and inadequate as air barriers.

Jan 1, 1976

By C. E. Munroe

In order to meet the emergencies of the world wr, tne quantities of explosivea produced in the Unitecl States, and the number of explosives plants were onti:.1.1.:l,lly ncreased so that when the armistice was declared the Government had on hand larg ..mounts oi militazy explosives in excess of existing military needs. Tle stor3.gs of these explosives entailed a liirge expense and their protection neessitatei the employment of m'3.l'lY men who could be better employed otherwise in the military estlish.11ent. Moreover, mar.y ex.ploives, like QJ.l other material, deteriorate on prolonged storage, They lose tht precise definiteness of properties and behavior on which reliance· is placed in military operations, The continued expen3e and d3.nger ttending storage of theae explosives might be diminished by dcst1et1on of the surplus beyond immediate needs, but such·deetniction is danger• ou5 qnd coetly. Hence, the evident solution o! the problem was the salvage d prompt ut111zation of the ru.rplua •

Aug 1, 1922

By A. T. Coumbe, I. F. Avery

The Bureau of Mines has completed a survey of petroleum pipe - lines by direct correspondence with the oil companies and the use of the records of the Interstate Commerce Commission in order to cover both interstate and intrastate systems . The review shows that crude petroleum and product pipe -lines in the United States had a total length of 152,814 miles on January 1 , 1950 , an increase of 25,463 miles since May 1 , 1941 , the time of the last previous survey . The expansion in pipe -line systems was due largely to new trunk-line construction , as the mileage built to carry refined products increased by 11,880 miles , and those intended for crude -oil transportation gained 6,193 miles . Trunk lines represented 60 percent of all pipe -line mileage on January 1 , 1950 , compared with 58 percent in 1941 . The average diameter of trunk -lines for crude oil , as calculated on the various sizes and weighted according to their respective lengths , increased to 9.8 inches on January 1 , 1950 , compared with 8.4 inches on May 1 , 1941. The mileage for lines up to 8 inches used in crude trunklines has decreased since the 1941 survey , while those of larger sizes have increased . The extensive use of large- diameter oil pipe -lines has developed since the construction of two major lines from Texas to the East Coast at government expense as a World War II emergency measure . The successful operation of these lines proved their economic advantages over smallerdiameter lines as well as their effectiveness in moving unprecedented volumes of oil during the period when tanker movements were restricted by submarine action in the Atlantic Ocean . The 24-inch diameter " Big Inch " line carries over 300,000 barrels daily of crude oil , and the 20 -inch " Little Big Inch " carried over 230,000 barrels daily of gasoline and light fuel oils to destinations where they were urgently needed . Hence , Although these lines were sold and converted to natural -gas service in December 1946 , after fulfilling their wartime mission , their record proved to the industry that significantly lower operating and investment costs per barrel -mile of oil moved could be achieved than were possible with the comparatively small lines in general use up to that time . the several major oil pipe -line projects that have been constructed since the late war are of large diameter pipe . To assure supplies and market outlets of sufficient magnitude to support such lines and provide adequate flexibility , ownership is often shared by several large companies whose transport needs are served in common . The principal recent expansion in facilities has been from supply points in Southwestern States toward markets in the North and East and to Gulf tidewater .

Dec 1, 1950

"INTRODUCTIONMany of the facilities and much of the equipment available to the Generic Mineral Technology Center for Respirable Dust are highly specialized and therefore, unique to the universities associated with the Center as illustrated in FIGURES 30 through 39.For example, a sample bank of 1300 U.S. coal specimens housed in the Coal Research Section, Deike Building of The Pennsylvania State University has been characterized for physical, elemental, mineralogical and maceral compositions. The results of this research have been used to initiate a study of the relationship between pneumoconioses and coal properties. Selected samples from this bank have been used in animal (primate) studies at the Milton S. Hershey (Penn State) and West Virginia University Medical Centers. These laboratory facilities for research in the medical and biological disciplines is state-of-the-art and includes a primate colony where dust research is currently underway. The Materials Research Laboratory and the Rock Mechanics Laboratory at PSU, and the Mechanical Systems Design and Control Laboratory, the Rock Mechanics Laboratory and the Mine Electronic System Laboratory at WVU are equipped for fundamental research on dust generation and characterization. While the majority of respirable dust research projects fall into these two categories, dust generation and characterization and interaction of dust and lung, there are other laboratory facilities available to the Center which are unparalleled in the type of equipment and expert personnel that they contribute to the program. The Mine Particle Laboratory located at the University of Minnesota and the Diesel Engine Laboratory at Michigan Technological University are examples. They house equipment and instrumentation that is unique to these facilities. much of it having been developed specifically for dust research by the research scientists there. The dust collection equipment and the fine particles measurement, characterization and analysis apparatus are essential to research in the areas of dust collection, particle characterization and diesel particulates. In addition to university laboratories, the research facilities of the National Institute for Occupational Safety and Health (NIOSH) are available to the Center through its relationship With West Virginia University."

Aug 31, 1989

By Albert E. Long

Since December 10, 1945, the Mount Weather Branch, Mining Division, Bureau of Mines, has been maintaining detailed performance and cost records on the diamond coring bits used throughout the United States by the Bureau of Mince. Figure 1 is a copy of a typical master record sheet showing the scope and type of information recorded for each bit. It is the intention of the Bureau of Mines to issue analytical reports covering the effects of diamond size and quality on the cost of core drilling in different rocks as the information on a significant number of bits used in any one type of rock is accumulated. This report is the first of such a proposed series and is based on the diamond loss and bit costs incurred in the use of 539 AX bits in coring operations on 10 different projects involving 6,097 feet of drilling in gneiss. The 10 projects were located in New York, Pennsylvania, and New Jersey (fig. 2). As a result of the information accumulated on the use of diamond-coring bits in drilling in gneiss, it has been found that the type of bit, the matrix, the percent of core recovered, and the size and quality of diamonds used have a definite effect on the cost of bits per foot drilled.

Jan 1, 1950

By G. W. Birge

Fifteen coal samples, representing the Winifrede, Chilton, Alma, No. 2 Gas, Powellton, Eagle, Douglas, Sewell, Beckley, Pocahontas No.4, and Pocahontas No.3 beds in Wyoming County, and five samples, representing the Fire Creek, Pocahontas No.6, and Pocahontas No.3 beds in Mercer County, W. Va., were carbonized at 9000 C by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expansion characteristics of the majority of samples were determined in the Bureau of Mines sole-heated oven. Chemical analyses and agglutinating values were determined for all coals. The coals were mostly strongly coking and low in ash and sulfur content. Dry, mineral-matter-free fixed-carbon content of the Wyoming County coals ranged from 63.0 to 83.4 percent. The Mercer County samples were all low volatile in rank. Yields of carbonization products were generally in accord with yields from similar rank coals of the Appalachian region. Because of their expanding tendencies, most of the medium-and low-volatile coals would require blending with lower rank coal for normal coke production.

Jan 1, 1965