Search Documents

By R. E. Heithecker

The separation of enormous quantities of water produced with the oil in some West Texas fields necessitated the use of special equipment other than the regular lease tanks. Several methods were used with varying degrees of success. They include the water-trap, hay tank and gun barrel, gun barrel and settling tank, chemical and electrical-dehydration methods. The water trap which has been used extensively in the Hendricks field, and in some instances has been installed in the Yates field separates the water and. oil under high pressure before tile liquid and gas pass through the flow beam. The first trap was constructed and installed by the Southern Crude Oil Purchasing Co. in July, 1928. By July, 1929, approximately 300 traps were in use. Treating cut oil by running it through a hay tank was done quite extensively in the Roberts-Settles field, Howard and Glasscock Counties, Tex., and later the method was used in the Hendricks field. In July, 1931, there were 37 hay tanks in the Roberts-Settles field, treating the oil from 123 wells. The cut oil frequently was made acceptable to the pipe-line company by running it through the hay tank. In some instances, however, it was necessary to heat the oil, and occasionally both heat and chemicals were used before complete separation of the oil and water was obtained.

Jan 1, 1932

By Lulie H. Crump

Salient historical data on consumption of fuels and energy have been summarized by State and census district for the years 1960 through 1972. This Information Circular covers States east of the Mississippi, and Information Circular 8705 covers States west of the Mississippi. These data replace previously published compilations of energy consumption statistics by States and districts. Future annual studies are planned using the same Btu conversion factors applied in these two. Information Circulars.

Jan 1, 1976

By Stephen W. Lambert

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978

By Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2007

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski County, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the eighth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is no followed by a description of each deposit developed in that half township. The 14 half township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations at those holes show on figure 13 in volume I. The descriptions of the deposits developed are followed by complete detailed logs at the drill holes. Many at the widely spaced exploratory holes did not discover bauxite of minable thickness and gra.de. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion covering that area.

Jan 1, 1948

By Frank E. Cash

"INTRODUCTION The iron—ore ranges in the Lake Superior district are the Marquette in Michigan, Menominee and Gogebic in Michigan and Wisconsin, and the Cuyuna, Mesabi, and Vermilion in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. Accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year but closely approximate each other over a period of years.This information circular supplements, continues, and combines the data in Information Circular 7321,2/ including figures of 1944 and 1945.During the 6—year period 1940 to 1945, inclusive, 481,485,475 long tons of iron ore was shipped from the Lake Superior district. 4/ Michigan and Wisconsin shipped 93,787,648 tons, or 19,5 percent of the total, and employed annually an average of approximately 14,300 men; Minnesota shipped 387,697,827 tons, or 80,5 percent, and employed annually an average of approximately 9,300 men. The tons produced per man employed is much greater in Minnesota than in Michigan and Wisconsin, owing to the large open-cut production in Minnesota."

Jul 1, 1947

By F. E. Block, Stephen D. Hill

The necessity for measuring radiation dose is encountered in studying both the beneficial and damaging effects of ionizing radiation on materials . It is also necessary to know the radiation dose absorbed by the reactants in order to evaluate the efficiency of reactions or processes that are promoted by radiation . Thus , a significant effort was made at the Albany cobalt 60 facility to investigate techniques by which the exposure radiation dose can be determined . Methods including ferrous sulfate , ceric sulfate , and methyl methacrylate chemical dosimeters , ion chamber dosimetry , and an absolute radiation calorimeter were investigated . Isodose curves were constructed for several standard source configurations using the dosimetry techniques which were investigated .

Jan 1, 1964

By E. E. Harton

Bureau of Mines Information Circular 7516, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants, was published in October 1949 to aid in estimating investment and operating costs of processes for manufacturing synthetic liquid fuels. Development of such processes by the Bureau of Mines was authorized by Public Law 290, 78th Congress. This bibliography included references to and abstracts of publications appearing from. 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. Bureau of Mines Information Circular 7705, Supplemental Bibliography on Investment and Operating Costs for Chemical and Petroleum Plants, was prepared to cover the area from September 1948 through June 1952.

Jan 1, 1956

By Seth T. Reese

THE INJURY DATA and experience at coal mines in the United States for 1949 are presented in this bulletin under the following general sections: (A) General injury experience: 1. Tables 1 to 18: Contain current data on number of injuries, frequency and severity rates, average severity, major and detailed classification of injuries, and distribution of injuries by part of body and days of disability. (B) Selected injury data: 1. Tables 19 to 45: Contain current data on various selected factors of operating and physical conditions that have contributed to the occurrence of injuries at bituminous-coal mines and at Pennsylvania anthracite mines. These factors include extent of hand and machine loading, size of mine by employment and production groups, thickness of bed or vein, duration and number of work shifts, rating of mine as gassy, or nongassy, types of cap lamps, ventilation, explosives, and combinations of factors that influence mine safety. (C) Injury experience by States: 1. Tables 46 to 52: Contain current data on number of injuries, frequency and severity rates, average severity, major classification of injuries, injury records of all coal-producing States, and the relative standing by States according to injury-frequency rates. (D) Appendix: 1. Tables 53 to 84: Contain certain injury data for the years 1943-47 that have not heretofore been published.

Jan 1, 1953

By N. N. Moelbs

The U.S. Bureau of Mines is conducting research on many topics relating to the hazards of coal mining, increased production, and protection of the environment. One area of research that has received scant attention in recent years is that of water inflows, probably because few fatalities in the United States have been attributed to them. As mining goes deeper, the problem of water in 1ow could increase dramatically because of adjacent or overlying mines in which huge water pools are impounded. Inaccurate mine maps and ineffective barriers can constitute a serious problem for operators both from gradual inflows and sudden inrushes of water. This report describes a wide but ineffective barrier that permitted an average 240-gpm inflow to a developing mine from an adjacent mine. The anomalous geologic structure that facilitated this leakage is described, demonstrating that size, alone, is no assurance against serious leakage. Some recommendations for managing serious water inflow are included.

Jan 1, 1989

By S. E. Khalafallo

The Bureau of Mines investigated the kinetics of reduction of wustite and magnetite with carbon monoxide. A mechanism was postulated wherein the interaction between gaseous and absorbed carbon monoxide appears to be the rate-determining process. This mechanism fully accounts for the experimental rate equation JL.h relates th velocity of reduction to the pressure of the reducing gas at constant temperature. It also explains the variability of the heat of activation of the reduction process with the state of aggregation of the oxide material. The integrated rate equation is in perfect agreement with the experimental reduction-time curves.

Jan 1, 1966

By T. A. Henrie

A technique was devised for measuring the rate of chemical reactions between reactive metals and molten-salt mixtures at high temperatures. The rate of the heterogeneous reaction between high-purity titanium metal and titanium trichloride in molten sodium chloride was determined. The reaction is surface-controlled, and the heat of activation is 8.29 kilocalories per mole TiC13. An active site or reaction nuclei is created by adsorbing a TiC13 molecule at the metal surface. Reaction of the second TiC13 species forms an activated complex that decomposes into three TiC12 molecules.

Jan 1, 1963

By Thomas L. Ochs

The Bureau of Mines is investigating the fundamental behavior of electric arcs in electric furnace operations. The electric arc is a poorly understood phenomenon. If the arc in a steelmaking furnace can be more carefully controlled, it should be possible to increase heat transfer to the melt, reducing both electrical and acoustical noise. As a first step toward a better understanding of the are, voltage and current signals from operating furnaces were analyzed. The results of the initial analysis show that instrumentation used in monitoring and controlling furnaces, such as meters and strip-chart recorders, gives incomplete or erroneous information to the operator and therefore leads to less than optimal control. Advanced instrumentation and analysis techniques, such as the waveform analysis used in these investigations, can improve the understanding of operation and the control of electric furnaces. This report describes the instrumentation and the numerical analysis methods used and compares these methods with standard metering and recording techniques.

Jan 1, 1986

By Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition, a revision which would supply up-to-date information on coal research and which would facilitate communication among organizations of similar interest seemed important. This compilation includes the names and activities of organizations of various types-government, university, private, and industry. The areas of investigation that each organization is engaged in are indicated in broad terms: Analysis and constitution, mining and geology, preparation, briquetting, combustion, high-and low-temperature carbonization, gasification, conversion to solid and liquid fuels, and health and safety. Publications issued by and describing the work of each organization are cited; almost all of the organizations also publish results of their investigations in the technical press. Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country. Information that would improve coverage and accuracy of the next revision of the publication will be welcomed by the Bureau of Mines.

Jan 1, 1966

By Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition, a revision which would supply up-to-date information on coal research and which would facilitate communication among organizations of similar interest seemed important. This compilation includes the names and activities of organizations of various types-government, university, private, and industry. The areas of investigation that each organization is engaged in are indicated in broad terms: Analysis and constitution, mining and geology, preparation, briquetting, combustion, high- and low-temperature carbonization, gasification, conversion to solid and liquid fuels, and health and safety. Publications issued by and describing the work of each organization are cited; almost all of the organizations also publish results of their investigations in the technical press. Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country.

Jan 1, 1966

By A. H. Roberson, F. S. Wartman

For many years , it has been the common practice at most copper mines to recover copper in solution in effluent mine water by precipitating the copper with scrap iron.4/ The technique employed varies from simply throwing scrap iron or tin cans into the waste ditches to passing the water through elaborate launder systems containing detinned scrap and baled cans . In general , a considerable amount of low - cost copper has been recovered that otherwise would have been lost . Iron consumption usually varies from 1 to 1-1/2 pounds of iron for each pound of copper recovered . The grade of the precipitate may be as much as 90 percent copper.4/ ,5/ Where the consumption of iron is materially greater , its cost is likely to be the determining factor of profit . In times of emergency, when the demand for scrap iron for remelting increases the cost of the iron sharply, and the supply of tin cans is not large enough to meet requirements , recovery of the copper might not be economical . The three principal reactions that take place when an acid mine water containing iron and copper salts in solution is brought into contact with metallic iron are : (1 ) Copper is precipitated and an equivalent amount of iron is dissolved , CuSO4 + Fe Cu + FeSO4 ; ( 2) ferric salts are reduced to ferrous salts , Fe2 (SO4 ) 3 + Fe = 3FeSO4 ; and (3) the free acid in the solution reacts. with metallic iron to produce ferrous sulfate , H2SO4 + Fe = H2 + FeSO4 . = Because of the reported high.consumption of iron (5 to 6 pounds per pound of copper precipitated ), when copper in water from the Hornet mine of the Mountain Copper Co. ( California ) was precipitated upon scrap iron , a series of tests was made to determine . the . optimum treatment, time , and consumption of iron .

Feb 1, 1944

By Alphonso Cornejo, Galen H. Clevenger

This bibliography was compiled in connection with an investigation of the Caron process for the treatment of manganese - silver ores , conducted by the T. S. Bureau of Mines in cooperation with the Netherlands East Indies Government . The object of this investigation was to develop a practicable method for treating the refractory manganese- silver ores found in these two countries . The results of the work will be published as a bulletin of the Bureau of Mines . This bibliography summarizes the available information on the subject previous to the investigative work embodied in the forthcoming bulletin, and may be useful to those metallurgists or others conducting work along this line .

Mar 1, 1923

By G. Richards Gwinn

The mineral graphite, a form of carbon, has been known for hundreds of years, and, was first used commercially as a coloring agent. Its true identity, however, was not recognized until the end of the eighteenth century, and its commercial development did not become extensive until near the close of the ninteenth century.

Jan 1, 1943

By R. E. Cumings

The Bureau of Mines made electrorefining tests in inert-atmosphere, molten salt cells to develop methods for the preparation of high-purity molybdenum. Seven of the electrolytes investigated were suitable for the preparation of refined metal. The electrolytes were composed of molybdenum chloride in alkali chlorides or mixtures of alkali and alkaline-earth chlorides. An electrolyte composed of potassium chloride and potassium hexachloro-molybdate was selected for a larger scale, more detailed study on the basis of its ease of preparation, its ability to retain the molybdenum salt, and the type of deposits obtained. High-purity molybdenum in the 99.99-percent-purity range was successfully prepared as dense plate up to 80 mils thick and as dendritic crystals. The temperature of electrolysis and the current density were major factors in determining whether plate or dendritic crystals of molybdenum were obtained.

Jan 1, 1966

Introduction The Coal Mine Roof Rating (CMRR) is a roof classification system. It was first introduced to the mining community in 1994.The CMRR filled a longstanding need to quantify geologic description of coal measure rocks into an engineering value that could be used for mine design. It has now been written to a user-friendly visual basic code that can be run on any PC with a Windows operating system. Background Rocks that form the roof of coal mines can vary widely and quickly in composition, extent, and defects. This results in an equally broad range of rock properties that can substantially affect the ability of the rock mass to form a stable mine roof. The CMRR was designed to evaluate the properties of the coal mine roof rock mass that contribute to its weakness and convert them into a relative strength rating from 0 to 100. These properties include the cohesion and frequency of discontinuities like bedding, slips, shears, and joints; uniaxial compressive strength (UCS); and moisture sensitivity. With simple lab and field tests and observation, the CMRR can be calculated by technical and operating personnel with a minimum of training. The CMRR has been widely accepted in both U.S. and international coalfields. As a result, a number of roof control applications have been found for the CMRR. It is currently used as an input component in the Analysis of Longwall Pillar Stability(ALPS) program, which is used to design longwall chain pillars. Incan be used as a criterion for determining the appropriate width of mine entries. It has also been used to indicate the appropriate length of cut in weak ground. The CMRR can be used as a strength parameter to characterize inter burden between mined seams in the numerical modeling of subsidence effects. In any area where an estimation of coal measure rock mass strength is required, the CMRR can be adapted to fill this need. How It Works Originally designed to be used with underground exposures, the CMRR can also be calculated from core. The chisel test for bedding cohesion and the ballpeen hammer test for UCS are inappropriate for core. These tests have been replaced by point load testing both axially and diametrally. Two other measures that are common to standard core logging—Rock Quality Designation (RQD) and fracture spacing—are also used to estimate rock weakness. With these easily obtained parameters, the CMRR can be calculated from core and used in the mine planning and exploration phase. The input screens allow calculation of the CMRR for both underground exposure and core. The CMRR is reported both as a “dry" value and as a groundwater-adjusted value for moisture-sensitive rocks. There is a graphical output report featuring a lithologic column with annotated unit ratings and a roof bolt symbol representing the height of the bolted horizon. Another important feature is an AutoCAD interface. This feature allows the export of located CMRR data directly to an AutoCAD layer in XYZ form. In this way, drill hole data can be inserted directly to a base map.

Apr 1, 2003