Search Documents

By W. W. Roepke

The linear cutting system, developed by the U.S. Bureau of Mines, uses geometric principles developed by Cardan to produce a nearly constant cut depth. The new system has been extensively tested in a synthetic material under laboratory conditions to verify mechanical capability and to identify operational characteristics. Comparisons between 15-rpm linear cutting and 50-rpm rotary cutting systems show significant improvement in respirable dust entrainment, product size distribution, and energy usage. Respirable dust is reduced by as much as 90 pct. Recovered product showed a 67-pct reduction in -0.32-cm (-1/8-in) material and a 200-pct increase in +5.08 cm (+2 in) material. Average power was reduced by 66 pct for the linear cutting. Because the bit cutting paths differ between linear and rotary cutting, it was necessary to compare the two at the same cut depths and bit types. These comparisons show that low revolution per minute rotary cutting entrains about the same amount of respirable dust as the linear cutting system, but the average shaft torque may be 55 to 130 pct greater for the rotary system.

Jan 1, 2010

By Walter Murphy

For a number of years the Bureau of Mines has been studying the properties of crude petroleums produced in the United States and the Western Hemisphere. A number of reports have been published giving the analyses of crudes from the different fields and regions as made by the Bureau of Mines Hempel method of analysis.4 Several of these reports include analyses of crude oils from the Rocky Mountain region.5/ The search for new fields and new producing horizons in old fields in the Rocky Mountain region has been quite intensive during the last few years, and a number of discoveries have been made.

Jan 1, 1937

By J. F. McIlwain

Cobalt-base hardfacing alloys used for wear resistance consist almost entirely of metals largely imported into the United States. As part of an overall research program to help alleviate this foreign dependency, the Bureau of Mines has been investigating an iron-base alloy system as a potential replacement for cobalt-base alloys for some uses. To ascertain the melting ranges, thermal analyses were made of cast heats of alloys containing, in weight percent, 59-61 Fe, 16-19 Cr, 8-9 Ni, 1 Mn, 1 W, 1 Mo, 0.5 Cb, 0.6 Si, 0.3 C, and 0-12 stoichiometric TiB2. Powder alloys within this range of composition, prepared by mechanical alloying, were sized and applied to mild steel test coupons by nontrans-ferred-arc plasma spraying. The resulting thin coatings were >95 pet dense, with bond strengths of 35 MPa and hardness of 400 to 840 DPH. Abrasive and adhesive wear test data were compared to those of a plasma-sprayed cobalt-base alloy. A range of boride contents resulting in most promising properties was determined for further research.

Jan 1, 1985

By Bernadette C. Michalski

Mineral raw materials, labor, capital, and technology form the basis of industrial production. The augmentation of one or all of the elements--labor, capital, and technology--will result in industrial growth. Thus, an increase in the labor force would increase output. A similar result would be achieved by expanding capital investment and supplying labor with more equipment. Finally, industrial growth can be achieved by introducing more productive methods and techniques born of technological advancement. The Soviet Union has employed these elements in many patterns to catapult from an agricultural to an industrial economy in four decades. The early history of the Soviet Union was marked by limited capital and borrowed technology, forcing the Soviets to concentrate on an abundant labor reserve to support the industrial program. The source of this reserve was the rural population. In [1928], 80 percent of the working population was employed in agriculture. This figure dropped to 43 percent by 1956, whereas industrial employment in the same period increased from 8 to 31 percent.3/

Jan 1, 1960

By John C. Edwards

The Bureau of Mines developed a mathematical model to predict the oxygen requirements for a miner evacuating a mine. The model accounts for variations in the miner's escape speed with mine airway height, and for the empirically determined expressions for the weight-specific oxygen uptake rate for upright walking, stooped walking (duck-walking), and crawling. A Fortran computer program that is user oriented was prepared based upon the model's constitutive equations. Specific instructions for utilizing the program, as well as applications to miner evacuation from a mine, are presented.

Jan 1, 1986

By Robert C. Johnson

Domestic byproduct fluorine (in fluosilicic acid) availability at various price levels of aluminum fluoride were determined and a contingency availability curve developed. The supply of byproduct fluosilicic acid is restricted in amount to certain geographic regions, where plants processing phosphate rock are located, and the byproduct can be collected. The maximum possible U.S. annual supply, based on potential plant capacities, is 373,400 tons of fluosilicic acid containing 295,400 tons of fluorine. Based on inputs of 5, la, 25, 50, and 100 thousand tons per year, five levels of producing aluminum fluoride from fluosilicic acid (100 percent) were costed. Based on a 12-percent discounted cash flow rate, including the cost of salvaging the fluosilicic acid, the calculated selling price of aluminum fluoride ranged from $233 per ton to $448 per ton. At the higher price, 98 percent of the potential supply of byproduct fluosilicic acid could be used profitably; at the lower price only 46 percent could be used profitably.

Jan 1, 1973

As fulfillment of the requirements of Contract H0387019 for the United States Department of the Interior, Bureau of Mines, a complete field kit, for performing on-site determinations of individual employee Time Weighted Average (TWA) exposures to nitrogen dioxide (NO2) and nitric oxide (NO), has been developed by MDA Scientific, Inc. This report provides background information and experimental data validating the use of this kit with confidence to ? 10 percent accuracy.

Jan 1, 1981

By Alla D. Mah

The energies of combustion of two carbides of tungsten and two carbides of molybdenum were measured , and the corresponding standard heats of combustion were derived . The results are as follows : WC : AH298.15 ( combustion ) = -285,940 ± 250 cal /mole , W₂ C: AH298.15 (combustion ) = -490,660 ± 400 cal /mole , Mo₂ C : AH298.15 ( combustion) = -439,350 ± 600 cal /mole , MoC : AH298.15 ( combustion ) = -269,800 ± 1,000 cal /mole . The combustion heats were combined with the heats of formation of the corresponding metal trioxides and carbon dioxide to obtain the following heats of formation : WC : AH298.15 ( formation ) = -9.6 ± 0.4 kcal /mole , WC: AH298.15 ( formation ) = -6.3 ± 0.6 kcal /mole , Mo₂ C : AH298.15 (formation) = -11.0 ± 0.7 kcal / mole , MoC : AH298.15 (formation ) = -2.4 ± 1.0 kcal /mole . The heats of combustion and formation of MoC are tentative .

Jan 1, 1963

Air pollution control regulation$ already implemented or being considered for implementation require substantial investment of capital to remove the sulfur oxides from copper, lead, and zinc smelter gases. There will be an attendant increase in production costs and possibly an associated increase in the price of these metals to the consumer. The total investment and any resultant metal price increase will depend upon the control regulations that ultimately will be adopted by the individual States. Controversy has arisen between the metals industry and governmental control agencies regarding the status of stack gas desulfurization technology and the ability of industry to control sulfur oxide emissions to the degree proposed by some of the more stringent regulations currently under consideration. This paper evaluates the problems involved in achieving various degrees of control over smelter sulfur oxide emissions and the technology available to accomplish the task of assuring clean air. The estimated cost of compliance is reviewed for the copper, zinc, and lead industries, but principal at tent ion is given to the copper situation.

Jan 1, 1971

By K. T. Menzies

This report documents laboratory and in-mine analyses of diesel exhaust pollutants carried out to assess the fate of potentially reactive species in the mine environment. Specifically, the concentration of stable compounds including carbon monoxide and carbon dioxide, and potentially reactive compounds including nitric oxide, nitrogen dioxide, sulfur dioxide, aldehydes, formaldehyde, acrolein, formic acid, odorants, particulates, soluble sulfates, and polynuclear aromatic hydrocarbons were determined. The concentration and mass emission rates of these compounds were measured in the laboratory under three engine speed and load conditions and with three exhaust control conditions, i.e., none, catalyst, water conditioner. Once calibrated, the engine was installed in the Bureau of Mines Safety Research Coal Mine and the concentration of exhaust pollutants measured at several distances downstream (inby) of the engine. Laboratory results confirm the relatively small effect of exhaust control devices on most pollutants under engine conditions of low speed and load. At higher engine speed and load, the catalyst is more effective in controlling many pollutants. The in-mine data indicates that during residence times, which are typical for miner/exhaust contact, most diesel exhaust pollutants do not decrease in concentration. The obvious exceptions are nitrogen dioxide, sulfur dioxide and formaldehyde. The concentration of these pollutants is reduced by up to 75 percent in five minutes. The lack of increase in levels of obvious reaction products indicates that surface loss may be a major sink for these pollutants.

Jan 1, 1980

By Laurence G. Britton

Accurate flammability and ignitability data for chemicals form the cornerstone of procedures used to assess the hazards associated with commercial chemical production and use. Since 1967 the ASTM E27 Committee on the Hazard Potential of Chemicals has issued numerous, widely used consensus standards dealing with diverse testing and predictive procedures used to obtain relevant chemical hazard properties. The decision to issue a standard rests solely with the membership, which consists of representatives from industry, testing laboratories, consulting firms, government, academia, and instrument suppliers. Consequently, the procedures are automatically relevant, timely, and widely applicable. The purpose of this paper is to highlight some of the widely used standards, complemented with hypothetical but relevant examples describing the testing strategy, interpretation, and application of the results. A further goal of this paper is to encourage participation in the consensus standards development process. The paper is published in two parts. The first part (in the preceding issue of Process Safety Progress) dealt with the E27 standards pertaining to thermodynamics, thermal stability, and chemical compatibility. The second part, published here, focuses on the flammability, ignitability, and explosibility of fuel and air mixtures. © 2005 American Institute of Chemical Engineers Process Saf Prog 24: 12?28, 2005

Jan 1, 2005

By B. W. Gandrud

In 1927 Coghill showed that there is considerable liberation of the iron oxide mineral from gangue when the Alabama red iron ores are ground to a size suitable for classification and tabling but that there is not sufficient to make possible a high extraction and a high grade of concentrate. Coghill states: High extraction and 'high grade of concentrate cannot be obtained without grinding to a size comparable with flotation or cyanide practice. If grade of concentrate be sacrificed the grinding need not be so severe. These ores slime readily during grinding, and in most instances the slimes are only slightly higher grade than the original ore. Not only do they carry a considerable percentage of the total iron in the ore, so that to reject them as tailings would result in prohibitively low extraction, but they are too fine to be amenable to ordinary methods of gravity concentration. In 1929 the Bureau of Mines published results showing that certain Alabama oolitic iron ores could be concentrated by classification and tabling after grinding, with rubber-covered rods. This selective grinding produced slimes of much higher grade than the original ore, and they were considered part of the final concentrate.

Jan 1, 1934

By D. H. Chambers, Arnold M. Lansche

Electro recovery by amalgam methods was investigated to determine the feasibility of recovering pure cadmium from cadmium sponge produced during purification of zinc electrolyte at electrolytic zinc plants . Actual material used in this work was air- oxidized cadmium sponge . An acid rinse and zinc displacement technique was developed to amalgamate this oxidized cadmium . ( In - plant use of the recovery process would probably not require this step because of the fresh state of the sponge . ) Zinc was completely removed from amalgamated sponge by selective oxidation with air . Zinc - free cadmium amalgam was circulated by an electromagnetic pump through an electrolytic cell where cadmium of 99.9+ percent purity was electrodeposited onto a rotating aluminum cathode . Polarographic methods were developed for determining cadmium and zinc in mercury and in sulfuric acid solution .

Jan 1, 1964

By Alton B. Cook

A material balance equation was derived for calculating (1) the initial oil volume and (2) the relationship of average reservoir pressure to net gas in storage in reservoirs used for natural gas storage operations. The equation is also applicable to secondary-recovery operations where reservoirs are completely repressured and gas cycled. Using this equation minimized two probable sources of appreciable error in conventional material balance calculations: inaccurate measuring of and accounting for produced gas, and differences between true reservoir pressure and average reservoir pressures as derived from bottom-hole pressure measurements. A new procedure is presented for calculating water encroachment. By solving the conventional material balance equation and the derived equation for gas storage simultaneously, the values for initial oil in place and net water encroachment can both be determined.

Jan 1, 1966

By Steven J. Page

The Bureau of Mines used fiber-laden air to test two identical fibrous aerosol monitors (FAM) in order to establish the FAM-optical count correlation. The FAM is a unique instrument developed by GCA Corp. (GCA) to measure real-time fibrous aerosol concentrations. It will also respond to particulates that have sufficient shape irregularities to possess fiber characteristics such as the 3:1 length: diameter (L:D) aspect ratio. Results of the Bureau's laboratory tests showed that the FAM response is linearly correlated to concentration data obtained using the optical membrane filter count technique approved by the National Institute for Occupational Safety and Health (NIOSH), U.S. Department of Health, Education, and Welfare. A plot of the FAM-optical count correlation showed that FAM concentration readings are generally well within ±25 pct of the optical membrane filter count. Initial tests to estimate the best ratio control setting of the FAM for 5-µm fiber-length discrimination were performed using one instrument only (the ratio control setting determines the minimum threshold fiber length that will be detected by the FAM). The estimated setting was then used to correlate both FAM units. The result was a 65 pct difference in correlation between the two units. It appears that the major factor responsible for this difference was the internal adjustment of the photomultiplier detector sensitivity for each of the two FAM units.

Jan 1, 1980

By John D. Bardill

This report covers the magnetic surveying done in the Plattsburg area , which was part of a general survey, of magnetite deposits in New York State . Other areas being surveyed are the Star Lake district , St. Lawrence County ; Brewster district , Putnam County; and the Sterling district , Orange County. Reconnaissance indicated an area about 3 miles long and 1,200 feet wide , but detailed surveys have been completed on only a portion of that area . In several districts , surveys of this type have served as a basis in the selection of areas for exploration by diamond drilling by the Bureau of Mines .

Jan 1, 1947

By Cloyd M. Smith

Progressive mine management is placing increased emphasis on improved ventilation as a contribution to better safety , health , and productivity of miners . Management is on the alert for means of bettering the working environment by increasing the flow of air and distributing it more effectively to the working places , having in mind the necessity of avoiding exorbitant ventilation costs . A basic need in planning betterments of this kind is knowledge of existing rates of flow and air pressures , infCoorrmmaattiicon that is supplied through ventilation surveys . Some companies make partial surveys from time to time , but few make complete surveys on a routine basis . This report describes the practice of a large British anthracite -mining company , which operates 24 collieries in South Wales , in carrying out a routine program of ventilation surveying . Ventilation characteristics and climatic conditions in the working places of its collieries are determined at frequent intervals with a view to increasing the effectiveness of ventilation and protecting the health of workers . It is thought that many of the points of the procedure used in making the surveys and in compiling and reporting the results will be applicable to American practice and that a discussion of the program may be helpful to colliery managers who are planning similar work .

Oct 1, 1949

The Mateen deposit comprises two large spodumene-bearing pegmatite dikes that outcrop along the, side and crest of a hill overlooking 'Rill City in the southern Black Hills of South Dakota. The Bureau of Mines investigated the Mateen deposit as part of a comprehensive study of the lithium mineral-production possibilities in the Black Hills area. The work was undertaken during the second World War, when the demand for certain lithium salts and compounds exceeded the small productive capacity of the industry. During the course of the investigation, the Bureau of Mines took 61 large channel samples from surface trenches, 4 channel samples from a shaft, and 3 from the face of an open cut. In addition, 8 diamond core-drill holes were completed to investigate the attitude of one of the dikes at depth. Metallurgical tests were conducted by the Bureau of Mines to determine the feasibility of beneficiating spodumene-bearing ores from the Mateen dikes.

Jan 1, 1948

By John H. Hild

"INTRODUCTION Alunite occurs within a radius of 10 miles of Marysvale, Piute County, Utah, in veins and as replacements of igneous rocks. A number of each type of deposit was explored by the Bureau of Mines, in cooperation with the Geological Survey, under the Strategic Minerals program during 1942. The exploratory work comprised geologic and topographic mapping, diamond drilling,,bulldozer and hand trenching, sinking test pits, rehabilitation of old workings, sampling alunite exposures, and constructing and repairing roads.ACKNOWLEDGNENTSIn its program of exploration of mineral deposits; the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches-are under the supervision of Dr. R. S. Dean, assistant director.With particular reference to this publication, acknowledgment is given to Richard E. Mieritz and William E. Young, who assisted on the project at various times; P. T. Allsman, chief. Salt Lake Division, Mining Branch, who advised on exploratory problems and gave valuable assistance in preparing the report and illustrations; A. P. T. Schumann, for preparing the illustrations; and to Gordon L. Bell, Max Willard, and Eugene Callaghan, of the Geological Survey, who cooperated as representatives of that agency."

Nov 1, 1946

By R. K. Koch

The normal spectral emissivities of liquid Ti, V, Zr, Mo, and Pt were determined at the fusion temperatures in an electron-beam furnace using a water-cooled copper hearth. The normal spectral emissivities were estimated above the melting points by using adjusted two-color temperatures as approximations of the true temperatures for substitution in Wien's equation. Simultaneous brightness temperatures were determined with a micro-optical pyrometer. The true temperature ranges covered were 1,668° to 1,885° C for Ti; 1,919° to 2,013° C for V; 1,855° to 2,367° C for Zr; 2,610° to 2,751° C for Mo, and 1,772° to 1,990° C for Pt. The spectral emissivities for titanium and zirconium decreased with increasing temperature. At an effective wavelength (?) of 658 mµ the emissivity of titanium ranged from 0.51 to 0.45 and zirconium, from 0.47 to 0.41. The emissivities of vanadium (? = 658 mµ) and molybdenum (? = 657 mµ) were constant at 0.41±0.02 and 0.33±0.01, respectively. The spectral emissivity of platinum (? = 658 mµ) was constant at 0.39±0.02 up to 1,900° C; above that temperature anomalous data were obtained. A mass spectrometric study indicated that platinum was reacting with back-streaming silicon vapors from the diffusion pump when the ambient pressure was greater than 2 X 10-5 torr.

Jan 1, 1973