Search Documents

By J. W. Town

Studies were made by the Bureau of Mines to determine the influence of textural features on the beneficiation of phosphate minerals (pellets) from selected bed and composite samples representing different rock types of the Western Phosphoria Formation. The particle size of the samples was reduced by attrition grinding to minus 20-, 28-, or 48-mesh depending on ore grade and gangue matrix. Sizing of the ground material showed that the phosphate pellets would concentrate in the plus 200-, 270-, or 325-mesh size fractions sufficiently so that the phosphate content was above the 31.5 :cent P2O5 required for acidulation. The phosphate content of essentially pure phosphate pellets was shown to range from 33 to 39 percent P2O5. Microscopic identification of the particles in each size fraction showed that the phosphate was either in the pellet form and readily liberated or so intimately associated with the gangue matrix that size reduction necessary Co obtain liberation was impractical.

Jan 1, 1967

By D. W. Frommer

Composite samples of nonmagnetic taconite from the western Mesabi range were evaluated by reductive roasting, fine grinding, and magnetic separation to determine potential sources of concentratable material. Although large tonnages of nonmagnetic taconite are known to occur in the western Mesabi district, these materials are not as yet a commercial source of iron ore. The technique employed permits the evaluation of individual composites and blocks of composites in terms of responsiveness to a process of potential commercial significance. The 159 composites, from open-pit mines located between Grand Rapids and Chisholm, Minn., were evaluated in the following sequence: 1. Minus 8-mesh material was roasted at 500° C. in hydrogen. 2. The roasted are was ground to one or more sizes in the minus 100-to minus 400-mesh range. 3. The roasted ground ore was magnetically separated in a Davis tube. 4. Composites were classified according to degree of grinding required to produce minimal concentrates. (Minimal concentrates are herein defined as those containing less than 10 percent silica, and responsive composites as those yielding minimal concentrates.)

Jan 1, 1962

By David D. Walker

The purpose of the investigation was to describe and appraise tungsten deposits in Montana . The work supplements previous investigations made by Pattee ( 10 ) and Walker ( 17 ) in selected areas of the State . Scheelite deposits in tactite are the most numerous and most important economically , having accounted for nearly all of the State's tungsten production . Of the 64 deposits examined during the current study , 50 contained scheelite , 11 hubnerite , 2 wolframite , and 1 ferberite . The State's major tungsten production has been from scheelite deposits in Beaverhead County . The report lists , by counties , the type and grade of each deposit . The more important occurrences are accompanied by geological and assay maps .

Jan 1, 1963

By P. W. Jeran

The Stereonet Analysis Program (SNAP) is a mathematics tool which, by means of a computer, reproduces mathematically the manual techniques of pre- paring stereograms. This computer program was developed to provide a fast, accurate, and economical means of analyzing fracture orientation data. It is mitten in FORTRAN IV for use on a UNIVAC 1108 operating under an Exec II system, but can be adapted to other systems. SNAP is currently being used to aid in the analysis of cleats and other geologically induced fractures associated with coalbeds that are being mined underground, Methane flows through the coalbed and into these mine workings predominantly through the fracture system. Therefore, knowledge of fracture orientation is an invaluable aid in the development of methane control technology.

Jan 1, 1970

By K. P. V. Lei

The Bureau of Mines investigated molten salt electrorefining 'n helium atmosphere cells as a means for the production of ductile vanadium. 'Electrolytes composed of NaCl-VCl2, LiCl-NaCl-VCl2, BaCl2-KCl-NaCl-VCl2 KCl-LiCl-VCl2, and CaCl2-NaCl-VCl2 were tested. Two electrolytes, KCl-LiCl-VCl2 and CaCl2-NaCl-VC12, were selected for laboratory-scale production tests. A molten salt electrorefining process was developed for the production of ductile 99.6 percent vanadium from a commercial 90-percent grade. Using the CaCl2-NaCl-VC12 electrolyte, an 87-percent recovery of ductile vanadium was made; an 85-percent recovery was made with the KCl-LiCl-VCl2 electrolyte.

Jan 1, 1967

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2 ) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs' estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By F. J. Perzak

The Bureau of Mines conducted a study to develop a standard fire test for 5-gal containers used for storing combustible fluids in underground coal mines. A standard test method was developed which evaluates the performance of the container in a 4-min tray fire. Bureau investigators used the standard test method to evaluate several types of closed 5-gal plastic and metal cans in outdoor tests. Each can tested contained 1 gal of nonfire-resistant (NFR) hydraulic oil. A container failed the test if it lost its contents in any of seven trials. Contents spilled either as a result of thermal rupture or melting. Fewer than 10 pct of the metal containers failed this criterion, but all the plastic containers failed. The metal container failures were usual-ly due to tipping over during pressure relief, which spilled the NFR oil. Replacing the NFR oil in the container with kerosene resulted in failure of more than 30 pct of the metal containers. The standard tests and preliminary tests showed that plastic containers are not equivalent to metal containers in their ability to contain combustibles such as lubricants and greases in a fire. For solvents and lubricants more volatile than NFR hydraulic oil, approved metal safety containers are recommended.

Jan 1, 1985

By E. C. Lane

This paper is the first putt of a report giving the results of the Bureau of Mines' twenty-third semiannual survey of motor gasoline marketed in the United States. A companion report, Part II, is in preparation and will give a more detailed discussion of the whole survey. Results of the determination of copper-strip corrosion, color, sulphur content, copper-dish evaporation residue, and gum content as given by the Bureau of Mines steam-oven method will be presented in the second paper, which will also include the prevailing retail price and the tax at the time the sample was taken. This paper deals specifically with data relative to gravity, Reid vapor pressure,' and distillation (method 100.13).6 The samples tested were divided into "competitive-price gasolines" and "premium-price motor fuels," a method of presentation that was begun with the twenty-second semiannual survey. A total of 312 samples were collected from service station pumps in 20 cities throughout the United States. Of this number of samples, 207 were "com-petitive-price gasolines" and 106 were "premium-price motor fuels." All of the samples were collected in March, 1931, and analyzed at the Petroleum Experiment Station of the United States Bureau of Mines at Bartlesville, Okla. "Competitive-price gasoline" includes those fuels that are sold at the generally recognized local base price and all fuels that are sold below that price. All fuels that are sold at an advance over the generally recognized base price are placed in the class of "premium-price motor fuels." These fuels include Ethyl gasolines, benzol blends, "high-test" fuels, and those fuels that owe their "anti-knock" rating to the process of manufacture rather than to the addition of other material such as Ethyl fluid or benzol. The term "high-test" is generally applied to motor fuels that are more volatile than the regular competitive-price gasolines. "High-test" fuels may also have a high anti-knock rating.

Jan 1, 1931

By C. E. Jordan

The Bureau of Mines is conducting research into the pneumatic recovery of coarse mica and has used this method to produce mica concentrates that contain more than 90 percent mica. This research is being carried out pursuant to the Bureau's objective to develop technology that will help maintain an adequate supply of minerals and metals to meet national economic and strategic needs. Researchers used a Bureau-designed system of crushers, screens, and zig-zag air classifiers to concentrate coarse liberated mica particles from mica-bearing materials. This pneumatic system was used to concentrate four mica ores from Arizona, North Carolina, and South Dakota and three waste tailings from Alabama, Georgia, and South Dakota. Using these samples, it was demonstrated that plus 65-mesh size mica can be effectively recovered by the pneumatic method. Not only were the concentrates high in mica content; it was also demonstrated that this method can be used to recover up to 78 percent of the mica that was originally contained in the samples. Because it is a dry concentration method, the pneumatic beneficiation technique may be advantageous in areas where water resources are limited.

Jan 1, 1980

By E. C. Foster

The project objective of this contract is to design, develop, and demonstrate a dust collecting system for auger head miners, used in coal seams 40 inches or less in height, which will reduce respirable dust below the limits established by the Federal Coal Mine Health and Safety Act of 1969. This system was to be incorporated into 3 Wilcox Mark 20 continuous miner. In order to accomplish this, the objective was divided in three main areas. First: To develop a dust control system which would remove by isolation, respirable dust from the face area and areas where miners work. Second: To develop a dust scrubbing system to remove and collect float dust before the air reaches the return airway. Third: To reduce the overall noise levels to which the miners are exposed.

Jan 1, 1974

By T. F. Mitchell, J. V. Batty, R. R. Wells, R. Havens

"INTRODUCTION )ne of the most important wartime activities of the Bureau of Mines was the search for new sources of minerals necessary to the prosecution of the war. As a part of the investigation of strategic mineral deposits in the United States under the Strategic Minerals Act (Public 117, 76th Cong., 1st Sess., Ch. 190), examining engineers of the Bureau of Mines investigated and sampled various deposits of chrome ore in California, Idaho, Montana, Oregon, and Washington, and those deposits that warranted further study were explored by diamond drilling, trenching, and drifting, as re¬quired. During these investigations, samples were submitted to the Ore Dressing Section of the Salt Lake City Station for metallurgical testing. This paper gives data summarizing results obtained from laboratory ore-dressing studies of the chrome ores submitted.Although the deposits range widely in geographical location, the mineral occurrence of all of them is strikingly similar. Chromium, in all of the ores tested, is present as impure chromite or chromium spinel. Although pure chromite (FeCr204 or FeO.Cr203) contains 68 percent chromic oxide, the iron may be replaced in varying amounts of magnesium, and the chromium may be replaced similarly by aluminum and ferric iron. In studying concentration methods as applied to chrome ores, the composition of the chrome mineral is of fundamental importance, because it is manifestly impossible to produce a high-chrome concentrate from a low-chrome chromite by any mechanical process.In all but one of the ores, the gangue material consists of olivine or altered olivine minerals such as serpentine, antigorite, and chrysotile. The exception, the Antelope or from Montana, has a gangue chiefly composed of actinolite, chlorite, and talc."

Jun 1, 1947

By W. M. Merritts

A joint investigation by the Bureau of Mines and the Christopher Coal Co. at the Humphrey No. 7 mine, operating in the Pittsburgh coalbed in northern West Virginia, was undertaken to gain more insight concerning the hazardous emission of methane gas in mining, This report describes the equipment, procedure, and results. Horizontal bleeder holes drilled in the faces drained large quantities of methane, eliminating downtime of mining equipment. Also, larger quantities of methane were removed by forcing 14 to 25 g.p.m. water at 25 to 200 p.s.i. 5 pressure into the bleeder holes, In one infusion test a fluorescein dye was added to the infusion water; in later mining operations, the infusion water was traced for a distance of 1,500 feet. With vacuum pump applied to the horizontal hole the gas-flow rate increased, and the methane content decreased.

Jan 1, 1962

6784. Barnes, V. L., and Romberg, Frederick. Gravity and Magnetic Observations on Iron Mountain Magnetite Deposit, Llano County, Tex. Geophysics, Menasha, Wis., vol. 8, No. 1, 1943, pp. 32-45. An outcrop of magnetite in the Central Mineral region of Texas is explored experimentally with a dip needle and a gravity meter. Two anomalies are observed, one due to the outcropping body and one probably due to a previously unknown body close to the outcrop. The possible attitudes of the bodies are discussed, and their masses and probable dimensions are computed from the gravitational observations. - Author's abstract.

Jan 1, 1943

By E. C. Tarpley, R. A. Drogowski, R. F. Abernethy

Three of the test methods frequently used for the determination of moisture in the analysis sample of coal were employed in analyzing a series of coals ranging in rank from anthracite to lignite . For most coals , the variation between the three methods are within the tolerances allowed between duplicate determinations by the same method . The processing variables studied included atmosphere , flow rate of atmosphere , inert atmospheres , oven temperatures , heating time , exposure of the dried coal to laboratory air , and surface area of the test sample . Unless close control is kept on these variables , erratic results will be obtained .

Jan 1, 1964

By L. H. ADAMS, C. N. HASKINS, J. K. CLEMENT

In the course of its investigations of the fuel resources in the United States and of the methods by which these resources could be utilized with greatest efficiency, the United States Geological Survey tested a great variety of coals and lignites as gas-producer fuel. Early in these testa it was found that many factors controlling the formation of gas in the generating chamber of the producer and, consequently, having a direct bearing on the management of producer-gas plants, were not as well understood as they should be. The Geological Survey therefore took up a detailed investigation of the chemical and physical processes that take place in the producer, keeping in view not only the possibility of increasing the efficiency of the producer as a source of energy, and the ensuing benefits to the public of cheaper power and greater utilization of low-grade fuels, but also the application of the results to the problems of boiler-furnace operations. - The Bureau of Mines, to which the testing and analyzing of fuels as carried on by the United States Geological Survey has been transferred, is continuing producer-gas investigations at the testing station at Pittsburg, Pa. Results of the gas-producer tests a made at the coal-testing plant erected at St. Louis, Mo., and of a study of some of the problems° that came up in the tests have been published by the Geological Survey. Results of the tests made at Norfolk, Va., and Pittsburg, Pa., and of further studies of particular problems, will be published by the Bureau of Mines. In the gas producer solid fuel is transformed into more readily combustible gaseous fuel. The transformation is relatively slow and consists of several processes: 1. The distillation of the volatile hydrocarbons from the freshly fired fuel at relatively low temperatures. 2. The combustion of the fuel by its combining with the oxygen of the air forming carbon dioxide (COO. 3. The formation of carbon monoxide (CO) and hydrogen (11 3), the essential constituents of producer gas, in accordance with the equations:

Jan 1, 1911

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: ? Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. ? Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. ? Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

By R. B. Tippin

To study continuous operation of the heavy liquid separation (HLS) of minerals, the Bureau of Mines concentrated spodumene from a typical ore. The studies included heavy liquid concentration, removal of the heavy liquid from the mineral products, and recovery of the heavy liquid for reuse. The research program examined the influence of feed moisture, steam consumption, stripping time, and condition of steam. Operation of multiple cyclones in series resulted in spodumene concentrates assaying 92 to 95 percent spodumene and indicated mineral recoveries of 86 to 89 percent. Continuous filtration and steam stripping produced mineral products containing less than I pound of heavy liquid tetrabromoethane (TBE) per ton of material. Problems unique to this process are discussed, including heavy liquid properties and viscosity, toxicity, material handling hazards, and safety precautions.

Jan 1, 1970

Comparative tests of four coals used industrially for coke production have been made by three laboratories of the Federal Bureau of Mines, each using its standard equipment and procedures for evaluating coal for coking. Two of the coals were blends used in the western and eastern sections of the United States, the third was a strongly coking coal widely used for producing coke in Alabama, and the fourth was a blend typical of those used for producing foundry coke in the Birmingham district. The coals used and the cokes produced from them covered a wide range of chemical and physical properties. The tests used at all three laboratories for determining the physical properties of the cokes were made according to ASTM (American Society for Testing Materials) methods. The excellent agreement found for the physical properties of the cokes indicated that, for the coals tested, the BM-AGA (Bureau of Mines-American Gas Association) 18-inch circular retort used at Pittsburgh, Pa" the 14-inch slot-type oven used at Denver, Colo., and the 17-inch slot-type oven used at Tuscaloosa, Ala., were substantially equivalent for evaluating coals for production of coke. Thus, added value is given to data obtained previously and independently at these three Bureau laboratories. INTRODUCTION Laboratory equipment to produce coke for evaluation has not been standardized by the industry. The results obtained with anyone design of equipment have been regarded as showing only the relative values of coal to produce coke of the requisite quality. Few systematic studies have been made to correlate results obtained in different types of equipment. Results of one, in which the Bureau of Mines participated, were published recently.2/ This

Jan 1, 1961

By Kenneth Eilerts

[Efficient and econonic production of ?etroleum requiros knowledge of the propertios of rescrvoir fluids a:$. their characterintics of flow throayh porous forclntions. The cllanga in propertie s and flow characteri s- tics of fluids when their corosition is altercd cs a rnsult of reservoir- pressure decliae is of 'mecial i~ortenct? ir, planning wall-spaAng pro.yama and production schedules. Rct~ntion of the ~eatent poscible quantity of dissolved gac in the rescrvoir liquid gnneml'y is recognized cs ess~ntisl to mxim ultimzte recoverj of oil fro3 the underground reecrvoir. Ilo:rever, pro6uction mothodn tending to mintain gis in solution in the oil and re- sulting in the optimm ocolo~ic recgvery of oil not only vary from field to fiold but also my have to be changed from time to time in a given field as it is being depleted of its recoveraklo oil. Const vestly there is need tc investigztc tY.e propertiec of resa:-voir f kids corresponding to successivc stages of reservoir depleJ&ion with the view of obtnining infomation oacential to efficient prcriuctian practices.]

Jan 1, 1939

Objective: To discourage miners from going inby unsupported mine roof by developing intrinsically safe devices that render the attendant hazard more evident, direct a person's attention to read the warning message on the module, and thus avoid the hazard beyond the device.

May 1, 1997