Search Documents

By S. K. Mathur

This report identifies all the possible activities, variables and factors that contribute to the surface subsidence process over room and pillar workings. These factors are responsible for mine instability and collapse that ultimately transforms into surface subsidence. Such a failure mechanism is initiated by the failure of the mine floor bed and or the failure of the pillars or the failure of the roof after second mining, which eventually brings down the roof. The individual responses of the pillar, floor and roof rocks to the mining induced stresses and the complex interaction between these components can't be attributable to any single factor. Also, no attempt has been made to quantify the significance of each of these factors and relate to the ground subsidence due to the lack of field data. The discussion here is centered primarily on the first mining though second mining is mentioned very briefly,

Jan 1, 1982

By Edward L. McHugh, Stanley M. Miller, Jeffrey K. Whyatt

The point estimation method can be applied to the safety factor (SF) equation for any specified rock slope failure mode (such as plane shear, step path, or wedge) to obtain reliable estimates of the mean and standard deviation of the SF probability distribution. A gamma probability density function is recommended for modeling this probability distribution, because it allows only for positive values and is flexible enough to provide symmetrical shapes and right-skewed, exponential-type shapes for the SF distribution. The mean and standard deviation define this distribution, which then can be integrated numerically from 0 to 1 to obtain the probability of sliding, PS (portion of the SF distribution where SF < 1.0). The overall probability of failure, PF, for the potential slope failure mass is the joint probability that the rock discontinuities are long enough to allow kinematic failure (PL) and that sliding occurs along the rock discontinuities (PS); that is, PF = PSPL. This method for estimating the probability of sliding is extremely efficient computationally, and thus, expedites slope stability simulation routines used by NIOSH software to stochastically describe rock slope behavior and assist the engineer in designing catch benches for large rock slopes. Enhanced bench design translates into increased operational efficiency and safer working conditions in open pit mines and quarries.

By Jos. R. Guiteras

This paper describes the pumping operations at the Ajax, Cresson, and Vindicator dines in the Cripple Creek mining district of Colorado during the summer of 1936. At that time the three mines wore pumping 6,500 gallons of water per minute into the Roosevelt drainage tunnel. Cripple Creek is the most important gold district in the State; it has yielded gold valued at over $365,000,000. The mines engaged in pumping are among the largest producing properties in the district. ACKNOWLEDGMENTS The author wishes to acknowledge the friendly cooperation of mine officials at the properties visited. At the. Ajax mine information was courteously given by Clayton Kissel, mine superintendent, and his staff; R. Y. Roby contributed the drawings. For information on the Cresson mine, thanks are expressed to Al H. Bebee, mine superintendent, and his staff, especially to Guy Rorabaugh, master mechanic, and to engineer Carlton. At the Vindicator mine, J. S. Anderson; mine superintendent, and Robert Welch, master mechanic, assisted; the latter furnished most of the information about that mine. Acknowledgment is also made of the cooperation of M. H. Salsbury, engineer at the Portland mine, who supplied technical data on the Roosevelt drainage tunnel.

Jan 1, 1937

By Richard A. Dick

Eight blasts were fired in a 2-1/2-ft bench in the Stewartville member of the Galena Limestone formation in an aggregate quarry near Stewartville, Minn. The shots were dimensionally proportional to production-size bench blasts and were about 5 to 10 percent of full scale. The effects of site, timing of initiation, and burden-to-spacing ratio were studied in a 2 x 2 x 2 factorial experiment, using three boreholes, caw;, containing a 1/2-in charge diameter of high-density ammonia dynamite, in each blast. Detonation velocity measurements indicated that the dynamite detonated satisfactorily in the 1/2-in charge diameter. The effects of the three experimental variables were analyzed by weight for the percentage of oversized material produced and for size distributions determined by screening the entire muckpiles. The bench faces were painted before each shot in an effort to determine the origin of the oversized material. The square pattern (burden and spacing = 15 in) produced finer overall fragmentation and less oversized material than the rectangular pattern (burden = 15 in; spacing = 22-1/2 in). Sites 1 and 2 were about ft apart. Although site 2 produced slightly better overall fragmentation than site 1, the amounts of oversized material produced showed no significant difference. The timing of initiation (instantaneous or delayed) did not significantly influence the overall fragmentation or the amount of oversized material produced.

Jan 1, 1973

By Launa G. Mallett, Jr. Brnich

Overview: The first step to emergency preparedness and maintaining a safe workplace is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen at one time. Risk assessment can be used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. Purpose: This training package was developed to assist instructors as they (1) determine how to use risk assessment to improve safety preparedness and (2) present risk assessment concepts and tools to trainees. The concepts and tools presented here can be applied to any mine hazard.

Jul 1, 2003

By H. J. Sloman

Mining laws of the several coal-producing Stat e with respect to safety catches on mine cages and their testing are extremely variable and generally indefinite in scope. The most specific requirements are contained in the Coal Mining Laws of Washington,3/ as follows:

Jan 1, 1944

The combined production value of natural abrasives, which consist of tripoli, special silica stone, garnet, and emery, decreased in 1985. Shipments of processed tripoli increased slightly in quantity but decreased 6% in value, Production of garnet, an abundant iron-aluminum silicate, increased 24% in quantity and 20% in value. There was an 11% increase in the quantity and a 7% increase in the value of refined garnet shipped when compared with 1984 shipments, a new record high. Production of crude special silica stone decreased 10% in quantity and 14% in value, and shipments of finished special silica stone products decreased 85% in quantity and 68% in value. Both the quantity and value of special silica stone finished products sold or used were the lowest since 1981. Production of emery, an impure aluminum oxide, decreased 56% in quantity and 61 % in value of product mined and shipped. [ ]

Jan 1, 1987

By Forrest T. Moyer

Need for lightweight building materials was created in the latter part of the nineteenth century by a radical change in building design in which dead load or structural weight was transferred from thick, heavy, load- bearing walls of former construction practice to a load-carrying framework of beams and columns with thin walls. This new design was brought about by the introduction of structural steel followed by reinforced concrete and structural concrete as materials for the erection of the load-supporting frame. The new materials and method of construction made possible the erection of skyscrapers and the building of bridges with long spans, and made feasible additions of one or more floors to existing buildings. As size and design of the load-bearing framework are controlled chiefly by dead load, the natural result was a. search for and use of light- weight materials in partitions, floors, and exterior walls. However, these thin walls created problems of heat and sound. insulation, so that building materials which possessed good heat- and sound-insulating properties in addition to light weight were objects of extensive research. One group of materials developed to fill this need comprised lightweight concretes, of which some were obtained by the use of lightweight aggregates. Although the advantages of lightweight.materials were evident from the first skyscrapers, there was a transition.stage.between the old bearing- wall and modern skeleton-frame types of building, with the heavy and massive construction of the former superimposed upon the latter. Hence, it was not until the period between 1910 and 1930 that the new lightweight concretes were recognized and used more extensively in the erection of large, nonresidential buildings. From this type of construction, light- weight-aggregate concretes entered-fields of residential and small non- residential building; in which they were found desirable for production of prefabricated, large-size; masonry units. Although the weight of each unit was reduced sufficiently to enable one man to handle it easily, properties of the new concretes other than light weight were the principal factors in the ready acceptance of these new materials in residential building. Manufacture of precast units includes complete lines of masonry and back-up blocks, bricks; floor beams, columns and partition, roof, and floor tiles and slabs. Recent improvements in casting machinery, development of the vibration-pressure machine, and a more thorough study and knowledge of the requirements and properties of the concrete mix have all contributed materially to the rapid expansion in use of lightweight aggregates in this industry.

Jan 1, 1942

By John J. Baz-Dresch, Kenneth L. Bickel, Winthrop F. Watts

Catalyzed diesel particulate filters (CDPF&apos;s) reduce the concentration of diesel particulate matter (DPM) and may reduce the emissions of carbon monoxide (CO) and hydrocarbons (HC) in diesel exhaust. Asamera Minerals&apos; Cannon Mine first installed CDPF&apos;s in 1987, and currently has 12 diesel- powered vehicles equipped with CDPF&apos;s. The Cannon Mine and the U.S. Bureau of Mines collaborated to evaluate the durability and performance of a CDPF. One of the CDPF&apos;s used at the mine was periodically evaluated in the USBM&apos;s diesel emissions laboratory after 839, 1,584, and 2,881 h of in-mine service. The objectives of this report are to present results from the USBM&apos;s evaluation of this CDPF, to describe the Cannon Mine&apos;s experience and cost analysis of using CDPF&apos;s, and to make recommendations for the future use of CDPF&apos;s. CDPF&apos;s improve air quality at the Cannon Mine, but they frequently become plugged and are subject to excessive mechanical shocks and stress, shortening their useful life. Mine records indicate that CDPF&apos;s account for 0.8 to 4.9 pct of the vehicles&apos; operating cost at the mine. CDPF life to date has ranged from 1,671 h to more than 5,992 h. Laboratory tests of the CDPF determined that DPM removal efficiency decreased and regeneration temperature increased over time.

Jan 1, 1994

The above referenced contract between Badger Manufacturing Corporation and the U. S Bureau of Mines was executed June 30, 1975, as a result of the request for proposals for innovative machine concepts. We selected the cutting machine category because of the obvious lack of technical progress in this field for many years: Phase I of the contract required blasting fragmentation tests to determine proper blasting patterns for use with the auger-type kerf cutting machine. Phase II required design concept development for a machine capable of cutting a circular void as an aid to blasting.

Jan 1, 1975

By R. S. Dean

The possibility of cheap electric power for a number of mining areas in this country has suggested to many the idea of electric smelting of nonferrous ores in small units at or near the mines. The electric smelting of nonferrous ores was tested fairly thoroughly 20 years ago by United States Bureau of Mines and by others, and the fact that it did not achieve continuing workable success in any instance is sufficient proof that it offered no advantages at that time.

Jan 1, 1937

By A. E. Ketler

A second generation lighting system was installed in the Greenwich Collieries longwall. This report describes the hardware, installation, maintenance, and final results of the program.

Jan 1, 1978

A preliminary study was conducted by the Bureau of Mines to determine the effect of humidity on salt mine airborne dust levels. Results showed less dust where the humidity was elevated. Dust reductions appeared to be dependent on the equilibrium between humidity and salt.

Jan 1, 1980

By PW Meisel

An hydraulic-powered reel system to minimize peak tension transients in shuttle car trailing cables has been theoretically designed and analyzed using a computer. A single spring-loaded take-up sheave stores or gives up cable to maintain tension within specified limits. Controls have been incorporated to shut down the vehicle before all cable is removed from the reel and to de-energize the cable in the event of a reel/cable jam. Full-scale hardware configuration drawings sufficient for manufacture of a test system have been completed.

Jan 1, 1983

By J. Fletcher Smoak

The value of abrasive materials consumed in the United States increased 37% in value over that of 1983 to $439 million; of which, 58% was manufactured abrasives, 36% was industrial diamond (natural and synthetic), and 6% was natural abrasives. Production value of natural abrasives, which consist of crude tripoli, special silica stone, garnet, and emery, increased 4% Production of crude tripoli, a finely disintegrated chert, increased 12% in quantity and 8% in value. Shipments of processed tripoli increased only 3% in quantity but increased 16% in value, with large increases occurring in both major end-use categories. Production of garnet, an abundant iron-aluminum silicate, decreased slightly in quantity and value after posting continued increases in quantity and value since 1980. There was a significant decrease in the quantity and [ ]

Jan 1, 1985

By J. C. Gerdeen

This project was a supporting effort with research contract H0230016 at White Pine Copper Company. Creep properties of White Pine rock were determined. These and properties for bolted joints were used in finite element analyses of sections of the White Pine Mine which included analysis of bed separations in the roof and sloping faults. In-situ experimental measurements were made of tension, compression, and bending of resin bolts by use of strain-gaged bolts. Evaluations of bolting effectiveness and comparisons of predicted and measured roof behavior are given.

Jan 1, 1976

By C. M. K. Boldt

Between 1989 and 1991, the greatest number of accidents in surface coal and metal/nonmetal mines involved haulage trucks. In 1995, the most frequently cited factor contributing to the 100 fatalities in these mines was powered haulage. In 1996, over 50% of the 84 Fatalities in mining that year were in surface mining. Because some of the world&apos;s largest mobile equipment is used in surface mines, and this equipment is involved in so many accidents and fatalities, new technologies are needed to alert truck drivers and people in spaces around the truck to the possibilities of collisions.

Jan 1, 1999

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine&apos;s heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

By Mark P. Zaitsoff

The project involved design, construction, and testing of hydraulic models of culverts, decant and open channel spillways which are typical drainage structures used for protecting mine waste embankments. MSHA (The Mine Safety and Health Administration, U. S. Department of Labor) made a motion picture of the tests. Tests results and products in the forms of graphs, tables and films, demonstrate the principles and factors which govern the function and performance of the three types of drainage structures.

Jan 1, 1981

By E. R. Bauer

This report describes a U.S. Bureau of Mines investigation into the removal of gate road chain pillars in conjunction with longwall retreat mining. The research objective was to determine, through evaluations of the loads imposed on the gate road pillars and supplemental support elements in the entries, how the pillars, supplemental support, and entries were affected by the longwall abutment pressure. To achieve this goal, vibrating wire stressmeters and hydraulic flatjack pressure cells were installed in the support elements to monitor stress change caused by abutment pressure as a function of longwall face advance. The findings documented in this report are the result of information collected from instrumentation and observation at the mine. Pillar and support loading measurements and stability observations revealed that the roof and the sup- port elements remained stable during panel retreat, while the face progressed at a normal rate of advance. The ability to safely and efficiently mine chain pillars during panel retreat increases resource recovery and can provide several other benefits described in this report.

Jan 1, 1993