Search Documents

By Kenneth Eilerts

[The development and operation of ?combination on wells?5/ have created new and unusual problems, many of which cast to solved only if information is available concerning the properties of the fluids produced. Data as to the characteristics of the fluids at the relatively high pressures that exist in the reservoirs are especially important, and there is growing economic concern to know what part, if any, of the liquid recovered at the surface was liquid in the reservoir, As an extension of this problem, it is important to Know whether liquid will be formed in the reservoir it as a result o a isothermal retrograde condensation when the reservoir pressure is reduced. The pressure range of such condensation, if it occurs, is significant in the design of gas-recycling plants for maintaining reservoir pressures. In connection with the operation of such plants, it is particularly important to know how gyres sure and temperature will affect the yield of the liquid phase and the composition of the gas to be returned to the reservoir. It has not been possible to predict the behavior of these fluids that have high ratios of gas to liquid by comparing them with the behavior of low gas-liquid ratio fluids at identical pressures and temperatures. Such comparison fails because the proportions in which a component will be distributed between the phases of a system at any given temperature and pressure depend increasingly on the composition of the mixture as the critical temperature and pressure of the oysters are approached. Because many combination wells are producing from reservoirs that have temperatures near the critical point, experimental date on the properties of the fluids under reservoir conditions are particularly important at this time. To rest the immediate requirements of the industry for such experimental information an equilibrium cell has been constructed at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla. When adequate experimental date, have boon accumulated, it may be possible to mare dependable estimates of the phase relations ft. high gas-liquid ratio fluids at the pre runes and temperatures characteristics of ?combination-well? reservoirs.]

Jan 1, 1940

By R. J. Gunderman

A conventional trailing cable connection box on a continuous mining machine was modified by the addition of two innovative devices. These are a pressure vent to preclude buildup of high pressure due to an explosion in-side the enclosure, and a grommet-type cable entry to simplify and speedup cable entering procedures. The innovative devices were evaluated for eight and one-half months in a working section of an underground coal mine. Laboratory tests before and after the in-mine exposure show no measurable change in the devices. Following the favorable in-mine evaluation, technical performance criteria were defined to serve as the basis of approval for the use of the innovative devices. Additional tests to measure comparable gripping of the cable by asbestos rope, substitution rope materials and by the urethane grommet-type entry were included in this effort. Also, literature for the last 80 years was searched. Comments are provided as to how the innovative devices comply with 30 CFR Part 18.

Jan 1, 1982

By Frederick C. Tompkins

A complete service system was established for the monitoring of personnel exposure to N02 based upon the use of passive dosimetry. This system is structured such that minimum effort is required of the user: manufacturing, analysis, reporting, and record keeping functions are provided by the service organization. A field evaluation program was carried out in a dieselized mine to assess the performance of two passive dosimeters, the Walden GASBADGE TM dosimeter, and a tubular dosimeter developed at New York University. Side-by-side comparisons were carried out to evaluate dosimeter suitability for monitoring in the field, and to assess relative accuracy characteristics.

Jan 1, 1976

By Steven J. Schatzel, Robert B. Krog

Frictional ignitions are defined as the ignition of a flammable mixture of methane and air that is initiated by frictional heating. Ignitions created through the addition of energy from open flames and exposed electrical circuits are not included in this analysis. Energy released in a roof fall that creates a spark and ignites a methane mixture would be considered a frictional ignition. Frictional ignitions represent the majority of all ignitions in underground coal mines. Over the study period of 1983 to 2005, a total of 1993 ignitions were reported in underground bituminous coal mines in the United States, of which 1589 were frictional ignitions. Reportable ignitions to the Mine Safety and Health Administration (MSHA) are any unintentional occurrences of flame underground regardless of duration. Frictional ignitions were reported in 155 mines and 13 states. Continuous miners represented the largest source for frictional ignitions with 1090 (68.6% of all frictional ignitions). Longwall mining operations represented the highest concentration of frictional ignitions during this study period with 1365 frictional ignitions (85.9% of all frictional ignitions). The 17 mines with the most frictional ignitions were all longwall mining operations and had 1130 frictional ignitions (307 from the shearer) that represented 71.1% of the total. In 1983, mines with frictional ignitions represented 6.9% of operating underground mines and 36.6% of total underground coal production. The percentage of operating underground mines with frictional ignitions and their total production has increased steadily and in 2005 represented 9.8% of active mines and 46.2% of underground coal production. The three coalbeds with the highest number of frictional ignitions (Blue Creek, Pittsburgh No 8, and Pocahontas No 3) had 1049 ignitions that represented 66.0% of all frictional ignitions. The three states with the highest number of frictional ignitions were Alabama (710), Virginia (247), and Pennsylvania (242) that represented 75.5% of the total. Frictional ignitions peaked in 1991 with a high of 114. In 2005, only 34 frictional ignitions were reported. If only frictional ignitions that occur at the face are considered, there have been no fatalities since 1983. Since this time, there were 33 ignitions that caused 53 workers to lose a total of 2912 working days. When including ground falls, then there have been four frictional ignitions with one incident causing two fatalities and injuring eight workers. From 1983-1991, underground productivity and the number of frictional ignitions increased. However, productivity continued to increase from 1991-2000 while total frictional ignitions fell, thereby disproving this connection between productivity and frequency of frictional ignitions. Ninety percent of all frictional ignitions occurred in underground coal mines that liberated more than 393 L/s (1.2 MMcfd million cubic feet per day) of methane through the main ventilation system. Although methane production is not the determining factor for the occurrence of frictional ignitions, it is a good indicator of the anticipated frequency.

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961

By Eleanor Abshire

[THE INCREASING use of hafnium as a vital component in atomic power reactors has brought this metal into recent prominence. A literature survey was made and this bibliography was compiled to provide research and production groups with a ready source of reference to this important metal anti its compounds. This service is rendered by the Zirconium Information Center, which is sponsored by the Department of the Navy, Bureau of Ships, and the F .S. Department of the Interior, Bureau of Mines, tit the Bureau's Northwest Electrodevelopment Experiment Station, Albany, Oreg. The following reference sources have been reviewed for this compilation : Chemical Abstracts; Industrial Arts Index; Crerar Metals Abstracts; Nuclear Sciences Abstracts; Bureau of Mine; Information Cicular 7771, Bibliography of Zirconium; anal Bureau of Mint' Information Circular 7830, Bibliography of Zirconium, suppllement to Information Circular 7771.]

Jan 1, 1960

By R. A. Westin

[Polychlorinated biphenyls (PCR's) have been widely utilised as fire-resistant dielectric coolants; in electrical equipment used in mining applicants, including transformers, capacitors, electric motors, and electromagnets. In addition, PCB's have been used in hydraulic fluids and heat-transfer fluids and are present in many oil-filled transformers. The U.S. Environmental Protection Agency (EPA) recently banned the manufacture of PCB's and equipment using PCB's, and imposed strict requirements on the continued use and disposal of existing PCB equipment. This manual discusses the EPA requirements, suggests ways to decrease the risks resulting from continued use of PCR equipment, and surveys the non-PCB equipment that is available as replacements for the PCB electrical equipment presently used in mines.]

Jan 1, 1980

By Gordon R. Sima, John L. Bennett, Roger L. King

Electric shocks are a serious problem in the mining environment. Because of extremely wide ranging use of electrically powered equipment in the mining industry, the hazard to personnel due to electrical shock and related injuries are not restricted to any single area but cover the entire spectrum of mining activity. Electrical accidents, resulting in personal injury, due to im- proper or complete lack of grounding of electrically operated mining machines, form a significant percentage of the overall electrical accident picture. The object of this paper is to describe methods of detection of unsafe electrical conditions with respect to the grounding of electrically operated mining equipment. It also includes a discussion of prototype instruments which effectively monitor the condition of the grounding safety devices currently in use on mining equipment and warn of dangerous conditions as soon as they appear. The paper is based on work accomplished under USBM Contract Number 50357115. The contract was initiated under the Pittsburgh Mining and Safety Research Center Program. It was administered under the technical direction of PM and SRC with Mr. Roger L. King as the Technical Project Officer. Mr. Daniel B. Dawkins was the Contract Administrator for the Bureau of Mines.

By Lloyd Williams

1. The investigation shows that the Poplar Creek and Big Mary beds contain the largest known recoverable reserves of coal in Morgan County, Tenn. The Poplar Creek bed has been the most productive. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 96 million tons, as of January 1, 1954. Of this total, 59 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

By George J. Conroy

Electrical power generation was studied in a laboratory-scale, open-cycle vortex MHD generator, which offers several advantages over straight-channel generators that require separate combustors. Compactness, lower capital cost, and high-energy release are obtained by combining the combustor and generator into one unit in the vortex generator. In addition, the vortex generator uses a simple solenoid rather than the more complex and expensive saddle magnet required for straight channel generators. Although the vortex generator must utilize combustion gases with a low Hall coefficient in order to be efficient in direct comparison to the linear generator, the primary motivation for this experimental device in terms of ultimate objective was to investigate the vortex generator with applications to direct coal firing and with combustion taking place in specially designed expansion nozzles. The vortex device offers one decided advantage over the linear device in this regard because slag deposits do not degrade or short-circuit the coaxial electrodes as is the case for a linear machine. The experimental vortex generator consists of a modified cyclone burner 7 ½ in ID by 21 in long, with the inner wall used as one electrode together with a coaxial center electrode. Power was obtained by impressing an axial field of 3,000 G from an air core solenoid magnet. Tests were conducted by seeding natural gas seeded with potassium acetate and burning with preheated oxygen-enriched air. Power generation was lower than calculated because theoretical plasma velocities were not achieved.

Jan 1, 1972

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common- wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables 'were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1978

By Frank B. Fulkerson

Of the about 60 million pounds of aluminum used in the Pacific Northwest in 1960, 40 million pounds or two-thirds was used by 10 companies. One of these companies made airplanes and missiles; one manufactured roofing, siding, and tubing; three produced truck tractors, truck bodies, or truck trailers; two made architectural metal products; one made irrigation and industrial products; one was a general foundry; and one was a shipyard. These companies contributed to regional growth by developing markets outside the area; some have worldwide sales. Aluminum consumption increased at an average rate of 7 percent annually from 1954 to 1960. Airplane manufacture, formerly preeminent in aluminum use, no longer was in first place in 1960. By industrial group, the leading users were manufacturers of building products, 30 percent; airplanes and missiles, 22 percent; truck tractors, truck bodies, and truck trailers; 17 percent; general foundries, 5 percent; ships and boats, 4 percent; mobile homes, 4 percent; other transportation equipment, 3 percent; and irrigation equipment and all other products, 15 percent.

Jan 1, 1962

By T. J. Batchler, T. M. Barczak

The Code of Federal Regulations (CFR) requires that the transverse load capacity of stoppings be equal to or greater than traditionally accepted in mine controls, which for block stoppings is generally accepted as 39 psf as referenced in the preamble to the CFR standard. This measure is based on physical testing of a freestanding wall in accordance with ASTM E 72 specifications, where our past research has shown that the dominant parameter is the tensile strength of the sealant. A new protocol based on rigid arch loading of the structure is proposed to determine the true transverse load capacity of block stoppings. Arching is achieved by the restraint of the stopping against the mine roof and floor, whereby compressive forces are developed within the wall. A laboratory procedure using the NIOSH Mine Roof Simulator (MRS) to simulate rigid arching of block stoppings was developed and results verified through full-scale in-mine tests. The rigid arch tests have demonstrated transverse load capacities more than an order of magnitude higher than the ASTM E 72 evaluation method from which the 39-psf requirement is derived. More importantly, the rigid arch tests have shown that the load capability is dependent on the physical properties of the block and geometric properties of the wall and not the sealant.

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

By J. C. Kerkering, S. M. Miller, P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z, measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 1993

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

By Donald W. Mitchell

Research shows that water neutralizes the explosion hazard of coal dust when present in sufficient quantity and when intimately mixed with the dust. The quantity of water required to neutralize coal dust and coal-rock dust mixtures is about equal to the limiting moisture adsorptive capacity of the dust; the adsorptive capacity increases with increase in the fineness and volatile content of the coal. Pools of water or high atmospheric humidity do not reduce the explosion hazard. Although wetted dust is less dispersible than dry dust, poor dispersibility cannot be relied on as the sole safeguard against explosion. Dust mixtures that contain water in excess of their limiting adsorptive capacity are dispersed and ignited by severe initiation sources. Pure coal dust adsorbs water with difficulty and retains water poorly; adsorption and retention is increased by the addition of rock dust the coal; the rock dust agglutinates wetted coal and assures that incombustible is present should drying occur. Therefore, it is advantageous to rock-dust wet areas in bituminous coal and lignite mines. When coal-rock dust mixtures are wetted and subsequently dried, the explosion hazard is about the same as for dust which was not wetted.

Jan 1, 1962

By H. V. Makar

Laboratory tests were performed to obtain a quantitative description of the effectiveness of sodium sulfate (Na2SO4) for removing copper from molten iron and to determine the effectiveness of Na2SO4 on actual auto scrap. The tests were conducted on induction melted heats of iron averaging 0.58 and 1.50 percent initial copper and on cupola-melted auto scrap containing 0.45 percent initial copper. The Na2SO4 was added in powder form in amounts ranging from 2.9 to 43.8 percent of the weight of iron being treated. The data showed that copper removal for the various Na2SO4 treatments followed a similar trend, regardless of the iron composition that was tested. The equation Y = 1 - e-3.23x approximately reflects the relationship between copper removal and amount of Na2SO4 added, where Y is the fraction of copper removed and x is the ratio of the weight of Na2SO4 added to the weight of metal treated. Copper removals ranged from 3.3 to 74.5 percent and reductions down to less than 0.10 percent final copper were achieved in the auto scrap. Copper removals were generally accompanied by sulfur removal, and initial sulfur contents ranging from 0.10 to 0.20 percent were reduced to as low as 0.02 percent. High temperatures and long slag reaction times tended to induce copper and sulfur reversion from the slag, but, generally, the Na2SO4 treat¬ments were effective up to approximately 2,820° F with reaction times not exceeding 7 minutes.

Jan 1, 1968

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel's lower flammable limit.

Jan 1, 1968