Search Documents

By D. Lynn Gordon, Larry B. Weston, Michael W. Manhart, Patrick R. Bowden, Michael W. Redmond

Study of confinement effects on detonation characteristics and subsequent fitting form development as a function of confiner strength and thickness.

Feb 1, 2020

By Tapas Kumar Mukherjee, Sujit Kumar, Sanjay Kumar Singh

This paper dwells on the epic blast conducted at Tata Steel’s captive coal mine in India and the insights drawn from it. Optimal blast design parameters had to be ascertained for operating benches (6.56 yards (6 meters) to 16.40 yards (15 meters)) where shovels and mining pay-loaders are deployed. Better fragmentation and suitable muck profile with controlled vibration levels were the pre-requisites. The landmark blast was carried out at Quarry-AB, West Bokaro on 17th March 2017. The colossal blast was done with 275 US ton (250 tonnes) of explosives poured down 1074 drill holes of 6.5 inch (165 mm) diameter. This blast is unique from the perspective of vibration control as it was conducted near local villages situated beyond 546 yards (500 meters) but within 601 yards (550 meters)) from the blast site. The entire array of preparatory activities had been successfully and impeccably executed within the same day. The optimization was achieved through meticulous coordination between TSL team, M/s Solar and M/s IEL. When a rock is blasted, numerous interactions occur among granular particles which are impacted by rock mass properties, explosives properties, blasting geometry and the detonation timings. Optimized use of resources requires a better understanding of these interactions. Extensive field studies have shown that blast fragmentation and suitable muck profile influences the performance of downstream processes in a mine. Consequently, profitability of whole mining operation can be greatly improved through optimized fragmentation. For arriving at the best blast geometry, several blasts were conducted with differing ‘burden and spacing’ design and charging pattern at various loading benches of the mine. Eventually, the largest ever blast was successfully carried out. This accomplishment is the culmination of the insights derived, confidence built, and expertise evolved through a progression of larger blasts conducted earlier (202 US tons (184 tonnes) and 143 US tons (130 tonnes) respectively) by the same team. All blast parameters were within the recommended level and no adverse impact on nearby structures was evidenced. In-the hole VOD of different explosives was determined and placement of boosters was standardized. The signature blasts were conducted to optimize the delay interval between the holes in a row and between the rows. Blasting parameters were fine-tuned in alignment with the desired fragmentation level and muck pile profile conducive to smooth and expeditious loading and hauling by mining HEMM. Rock fragmentation analyses were carried out using photo-analysis system. The insights gained from this blast would serve as the cynosure for planning and carrying out more such blasts with highly optimized parameters in the future with the intent of improving mining efficiency and productivity

Jan 1, 2019

By Mark Svinkin

To save time for construction of coal pits, the contractor decided to combine erection of the tower pitheads with digging of skip shafts to the depth necessary for placing proper coal pit equipment. It was obvious that blasts used in shaft faces and lifting machines installed at a lower part of the pithead could excite vibrations of an upper part of the pithead with curing concrete. The contractor was concerned about vibrations of pithead concrete structures and the disturbance of freshly poured concrete in forms at a top of the pithead as a consequence of structure vibrations. The results of a study of the tower pithead structure vibrations from blasting and operating machinery, and effects of structural vibrations on curing concrete are presented. Structural vibrations were measured at the tower pitheads of two coal pits from twelve blasts. Records of horizontal and vertical displacements were superposition of harmonic low-frequency damped vibrations and sporadic high-frequency damped vibrations with a variable frequency. Low frequency vibrations attenuated during 8-13 s after the last delayed blast. Measured values of the natural frequencies of pithead horizontal vibrations coincided with the calculated frequencies of horizontal bend vibrations. An increase of a face depth from 18 to 50 m diminished 16 times horizontal bending vibration displacements of concrete structures. Measurements of vertical structural vibrations from blasting demonstrated increasing of vertical pithead displacements with the rising of structure elevations. This is evidence of the pithead longitudinal tension. The holes with charges were not properly condensed for one blast. As a result of incompact stemming, the blast substantially increased the energy of airborne pressure waves, which triggered natural vertical vibrations of the pithead with high displacements.

Jan 1, 2004

By C. Morel, P. Fredes, L. Rojas

This article presents a comprehensive study on the development and application of the specific module called "Exclusion Zone" created by Orica to determine blast evacuation exclusion zones. This module, integrated into the "SHOTPlus™ (blast design software)" software, has been used in the context of optimizing equipment evacuation exclusion zones in a northern Chile mine. The main objective has been to reduce the travel times of extraction equipment without compromising the safety of individuals. The module considers various factors such as the explosive charges used, stemming, sector topography, and detonation sequence to determine the rock projection generated by the blast. Furthermore, it utilizes information collected by drones and support tools such as Groundprobe and BlastVision™. The results obtained demonstrate that the use of this technology has allowed the optimization of blast evacuation distances in the northern Chile mine, generating significant economic benefits for the client.

Jan 1, 2024

By Donna Kliche, Charles Kliche

It has been previously documented that various weather conditions such as wind direction and speed, cloud cover and, especially, temperature inversions can significantly affect the overpressure generated by a blast event (Siskind et al, 1980; Oriard, 1999; Siskind, 2000). The overpressure can be magnified downwind and reduced upwind; a change in the regular profile of temperature with elevation can magnify or focus the sound intensity at some distance from the blast event.

Jan 1, 2011

By A. S. Tawadrous

This paper is an evaluation of Artificial Neural Networks (ANN) as a tool in the design of the geometry of surface blast patterns. The built model uses eight different parameters, which affect the design of the pattern. Those parameters are rock type, stratification, blasthole diameter, bench height, type of explosive, priming position, powder factor and fragmentation size required. The network was trained to predict burden and spacing of the blast pattern. The model was built and trained (back-propagation technique) using 43 case histories collected from the literature. The model has then been validated using 16 cases from operational quarries.

Jan 1, 2006

By Ambrose Buchanan, Rob Farnfield, Charles Adcock

Beginning on 7th September 1940 the City of London was subjected to 57 consecutive days of bombing in what became known as the ‘London Blitz’. To commemorate the 70th anniversary of this event a television series was commissioned that required the open detonation of World War 2 equivalent bombs close to purpose built structures constructed using period design and materials. The structures were built on a remote test facility in the North of England that is able to fire large quantities of explosive in the air.

Jan 1, 2011

By Peter Moser, Michael Messner, Florian Bauer

The existence of ammonia in underground blasting fumes was frequently measured in various field tests (6, 7). Ammonia in fumes with a TLV (threshold limit value) of around 30 ppm (slightly different in various countries) is a toxic gas but not considered to be a high risk for the underground work force as ammonia smells very itching and is extremely annoying. This might be the reason why ammonia is hardly measured in routine underground blasting fumes control. Another reason for the lacking measurement might be the circumstance that ammonia is a very reactive gas and the ammonia sensors available on the market are very cross sensitive to other gases like carbon monoxide. Nevertheless, especially since the introduction of bulk emulsion explosives in underground blasting, complaints from miners about ammonia in the blasting fumes increased. Research work by various institutions [8] around the world relates the ammonia in the fumes back to various mechanisms. Amongst others these comprise: a) non ideal (low temperature) detonation of explosives, with NH3 in the reaction products; b) reaction between rock and non detonated bulk explosives (especially when the rock is of a basic nature (high pH value); c) reaction between shotcrete and non detonated bulk explosives. Numerous blasting tests in an experimental underground set up have been made in order to check these hypotheses for ammonia origin in blasting fumes. None of them has been found to be responsible for sometimes high concentrations of ammonia in the fumes. The major reason for ammonia concentration in blasting fumes has been found in mine water of a high pH value (either natural or from using shotcrete). The mechanism identified is as follows: the moment a non detonated ammonium nitrate bearing explosive comes in contact with mine water of a high pH value, ammonia is formed immediately. The source for the undetonated explosive is twofold: firstly there is a certain spillage of explosives when the holes are charged (especially when using bulk products) and secondly not the entire explosives detonate completely. These undetonated remaining of the explosives end up in the muck pile after blasting. In case there is water of a high pH value the reaction between the explosives and the water starts immediately. This explains also the observation why ammonia can be measured in the blasting fumes quite a long time after the blast. The majority of the ammonia is not formed during the detonation; it is formed inside the muck pile even a considerable long time after the blast.

Jan 1, 2010

By Philemon Desrochers, Ken Qian Liu

Following the success of the West Ore Zone distress mass blast in 2001 at Brunswick Mine, a similar approach was taken to distress the North Regional Pillar (NRP) which contained over 3 million tonnes of high grade ore. The NRP is located on the 1000 m Level with very poor hanging-wall (H/W) rock mass qualities. After an extensive geotechnical review, the distress slot is located close to the foot-wall (F/W) of the NRP in order to have the competent ore as H/W. The longitudinal area to distress covers 115 m along the strike and 85 m high from 1000 1-sub to 850 Sill. Prior to the final mass blast, 3 voids were created to allow rock swelling: the North void, the South void and the trench just below the mass blast. After over one year of preparation, the mass blast of 202,000 tonnes was successfully initiated on February 7, 2003 with 1561 electronic detonators and 210,000 kg of emulsion explosives. The blast achieved its objective of distressing the NRP as indicated the mine-wide micro-seismic monitoring system. This paper describes different stages of the project from void preparation to the mass blast itself, as well as some detailed aspects such as muck-pile prediction for mucking sequence with the help of DMC_Blast simulation code and electronic detonators.

Jan 1, 2004

By Ken Eltschlager, J Silva Castro, J. M. Hoffman, Braden Lusk

This case study focuses on analysis of sounds inside a house induced by blasts as result of surface mining coal in West Virginia and how to better communicate technical information to the public. The field study included a house wide vibration and sound monitoring system installed in a home which was subjected to blasts at varied distances and direction. The structure response was separated into ground vibration and airblast induced movement due to the differences in their times of arrival. This signal was then compared to the sounds recorded to determine which component of blast (ground vibration or airblast) induced the maximum sound. Findings shows that blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast. While for blasts beyond this distance the maximum sound response was caused by ground vibration without exception. The kitchen generally created the most sound. The second phase of the study was to gauge the public’s response or preference to technical information. Three hundred and forty eight (348) telephone surveys were conducted in Logan and Boone counties West Virginia. Based on the survey, the public prefers units of pounds per square inch (psi) for airblast and millimeters of displacement for ground vibration. Ultimately a public relations plan was developed based on the results.

Jan 1, 2012

By Dale S. Preece, Ruilin Yang

Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidly attenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that the resulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of the explosive. The induced air blast reflects from the bottom of the borehole and this reflected pressure, even though doubled, is still approximately two orders of magnitude less than the detonation pressure. Air-shocks will ring back and forth in the air-deck for a few tens of milliseconds while the adjacent explosive column(s) are detonating. Transmission of the initial shock through the air along with reflections is an intensive energy consuming process. Energy balance results in shock heating of the air and a temperature increase. However, the increased temperature of the air is also orders of magnitude less than that of the explosive detonation products immediately behind the detonation front. Replacing high energy explosives with zero energy air-decks in a blasthole will always have a negative impact on the adjacent rock fragmentation and movement.

Jan 1, 2016

By Braden Lusk

Vibrations as a result of blasting practices in mining engineering are a complex phenomenon controlled by many variables. Mine blast vibration modeling and prediction is becoming more important as a consequence of interactions by mining activity with an ever closer public. Many communities (all over the world) close to mining activity often complain about airblast and vibrations produced from blasting activity. It is important for the mining industry to have tools and understandable methodologies to model and predict blast vibration. These tools can then be used to predict and control vibration at neighboring structures.

Jan 1, 2013

By Dr. Anthony J. Konya

The modern era has seen a boom in virtual training platforms. This study details the effectiveness & applicability of online training in comparison to in-person training for the drill & blast industry.

Feb 1, 2020

By Jon Hurt, Brent Meins, David Vardiman

"Two test blasts were conducted at the Sanford Underground Research Facility to establish optimum blast designs and to limit blast effects on existing research rooms and equipment in preparation for the largest deep underground excavation in North America. Located on the 4850 Level (4,850 ft below the surface)at the former Homestake Mine in Lead, SD, this excavation is part of the U.S. Department of Energy’sLong-Baseline Neutrino Facility that will house particle detectors for the international Deep Underground Neutrino Experiment hosted by Fermilab. A large array of seismographs was deployedthroughout the 4850 Level to measure ground vibrations and airblast pressures in tunnel drifts and in lab spaces."

Jan 1, 2017

By Vitor Fonseca de Barcelos, Jair Carlos Koppe

Our society is experiencing a digital revolution. Technology is demonstrating its significant potential for mining industry. In this paper are presented the measured and estimated impacts of applying new technologies on blasting operations in a copper mine.

Feb 1, 2020

By John Wall

The use of electronic detonators in civil tunnelling applications, to reduce vibration is small firings has been successfully utilised for a number of years. As part of the mining industry’s commitment to reducing blast damage during the development cycle in underground mining applications, a series of development blasts using eDevTM electronic detonators in typical mining applications was conducted in North Queensland, Australia.

Jan 1, 2012

By Sandy Tavelli, Thomas L. Barkley

This discussion will present a case study in developing solutions to a metropolitan quarry’s public relations, legal, environmental, and productivity problems. It details an extensive and detailed project to address the blasting practice in a medium sized quarry that is surrounded by residential and industrial zones. The principle work was done over a four-month duration during the normal production season. It included detailed drilling and blasting audits for baseline information. In addition, geologic characterization, seismic modeling, correction of deviations from best practices, and implementation and monitoring of precise electronic timing to provide dramatic solutions for the quarry. The quarry is in the near suburbs of a large metropolitan city. It is framed on two sides by residential municipalities and on two sides by industrial zones. At the start of the project, the quarry was in court as a result of the lawsuit by one of the neighboring towns that was suing to close the quarry. The lawsuit had progressed to the advanced stage where in the Judge had appointed an arbitrator to make the decision of continued operation. This arbitrator was to observe our progress and recommend to the Judge the disposition of the case.

Jan 1, 2004

By Scott G. Giltner, Alex Schwenk

Blasting within 250 ft of a crusher was successfully executed through the application of electronic detonators, 3-D imagery, signature hole analysis, custom loading of blast holes. The blast was well contained, the vibrations were minimal, and there was no flyrock.

Feb 1, 2020

By Tony Rorke, Sydney Thabethe

A large overburden blast was carried out at Douglas Colliery, Middelburg Mine Services, close to a national road in South Africa. The road is a busy route between Witbank and Bethal and damage to the road could not be risked. The section of road next to the blast was particularly prone to damage, because it had been mined out on its eastern flank, and the large blast was to take place on its western flank. There were thus three potential damage risks: 1. Fly rock damage to the road surface 2. Vibration damage to the road substrate 3. Damage caused by bulk displacement of the block supporting the road into the void on the mined out side. This paper presents the design and blasting methods used to control the blast and avoid these three risks. Electronic delay detonators were used in multi-decked holes. Signature data were used to determine the blast timing to make sure that delays were used that would provide destructive interference. The timing direction and sequence was decided using wave interference patterns to direct repeated shocks away from the road. The precise detonators and the odelling capability allowed effective control of the blast vibration result. Each hole was charged with two explosive decks separated by a deck of aggregate to limit the charge mass fired per delay and thus limit the reaction forces acting towards the unsupported road. The vibration and blast results are presented in the paper, together with the design that was applied. Details are provided on how the blast was charged and primed. The detonators that were used are described and the timing design is presented.Copyright © 2004 International Society of Explosives Engineers 2004G Volume 1 - Blasting Next to an Unsupported Road Using Electronic Detonators 1 of 13 It is concluded that damage risk to nearby structures can be effectively controlled using electronic delay detonators, provided the appropriate modelling is applied to obtain the most effective delay periods.

Jan 1, 2004

By Keith Best

It has been said that when a person does something right no one remembers but when they do something wrong no one forgets. This statement, when applied to the explosives industry, has never been truer. Think about it.How many times have you seen a news crew reporting on how well a blaster is doing his/her job? Normally, all you will see is how bad things are going and how much “damage” is being done.

Jan 1, 2008