Search Documents

By Q Liu, P D. Katsabanis

Dust explosions in underground sulphide and oil shale mines result from the detonation of explosives in the blasting operations. Explosive composition, oxygen balance, priming and ideality of detonation were examined theoretically and experimentally in the presence of reactive sulphide dust. It was found that the temperature as well as the chemical composition of the gaseous products of detonation are the controlling parameters related to the explosive. Non aluminized, oxygen balanced emulsion explosives were proven to be relatively safe, while explosives creating combustible products were proven to be extremely dangerous due to the secondary flame they generate. Since a large number of dusty orebodies are often very friable, low density emulsion explosives are also examined for application in production blasting.

Jan 1, 1991

By Paul Ross, Harry Burchett, Lou Case, Calvin J. Konya

"The Cumberland River in Harlan, Kentucky has flooded the town for numerous years. TheU.S. Army Corps of Engineers funded a project to divert the river. The project consisted oftunneling through a mountain to divert the river. The approaches to the tunnels requiredcontrolled blasting to create noses to help channel the water and debris into the tunnels.The geologic structure was such that conventional presplitting techniques were notproducing the desired results and were causing severe backbreak. Replacement of the rocknoses with concrete would cost about a million dollars; and therefore it was important tosave them if at all possible. Blasting techniques were developed which allowed the projectto be successfully completed. This paper will discuss the case history of the controlledblasting procedures."

Jan 1, 1993

In situ, most Taconite is heavily pre-fractured; because of the high cost of comminution of taconite, maximum fracture of pre-existing blocks is desirable. Sustained borehole pressure plays a significant role in fragmentation, especially by penetrating pre-existing fractures. The distribution of explosive-induced energy in the burden in three dimensions was calculated. Data on the comminution of single particles was used, with the distribution of energies and the distribution of pre-existing block sizes, to calculate fragmentation for a case study. The calculation agreed well with the measured fragmentation. Sequential comminution events are much more efficient than single ones, and enhanced fragmentation may be possible with alternative blasting practices. Some important factors in the dependence of comminution on energy input are discussed.

Jan 1, 1995

By Michael E. Kovach

This discussion is an overview of an approach to drilling and blasting angle holes at Martin Marietta Aggregates. Method of determining burdens, hole depths, angle settings and explosive selection will be discussed in detail with an emphasis on safety and production. Such techniques and methods involve the use of hand-held surveying instruments such as the Abney level, pocket transit and inclinometer along with measuring tape and burden pole. An interesting method developed by Oscar Banfield a retired Martin Marietta and E. I. duPont engineer, for setting the proper angle on a drill will also be presented. This treatise is a discussion of the use of simple yet important tools and techniques a blaster should use to resolve both routine and complex problems encountered during quarry blasting operations.

Jan 1, 1992

By Qi Jingyue, Wang Zhongquian, Yang Nianhua

Qinling Tunnel is the longest tunnel in China. The rock stratum is very hard rock - intact mixed gneiss. At the beginning of the construction, drift-pilot excavation is very costly due to the use of regular drill and blasting methods. After tests on the acoustic impedance match between rock and explosive, watergel explosive, which has a high velocity of detonation and high brisance, has been used for hard rock blasting. In addition, different cut plans have been compared. It was found that four-large-hole cut is the most effective. And the number of drillholes and specific charge cut down and the average advance reaches more than 94% of the blastholes depth. Thus, the difficult problem of hard rock blasting in drift pilot is successfully solved, while safe and quick construction is guaranteed.

Jan 1, 1998

By Justus Deen, Paul V. Sterk

Through the 119 year history of the Homestake Mine various methods of raise mining have been used, these include conventional, bored, and drop raises. These raises provide passage for men and supplies, provide ventilation, transfer broken rock from level to level, and serve as emergency escapeways. As the 1980s came to a close, many of the larger ore bodies in the mine had been mined out. This has resulted in many crown pillar situations that required a method to mine them. In addition, the Homestake ore body also contains numerous ore reserves that have short vertical height. The ore itself can be from vertical to 50 degrees in dip. Due to the high cost of drift and ramp development many of these ore bodies are sub-economic using conventional mechanized cut and fill mining.

Jan 1, 1996

By William McFerren, Pragasen Moodley

In contrast to global trends, African, especially South African, surface mining operations have shown a significant rate of adoption of Electronic Detonators (ED’s) over the last few years. Proven benefits of converting to ED’s from pyrotechnic initiation systems have aided this market conversion. These benefits are experienced throughout the mining operation. Benchmarking exercises, prior to the introduction of ED’s, form part of the conversion process and allow for quantifying improvements. Extensive work has been done on quantifying the benefits of converting to ED’s and have shown that results can be reproducible. Improvements have been experienced in many applications and include environmental impact control, improved mining efficiencies, increased cast benefit and improved size distribution. These step changes in blasting results, in conjunction with the adoption of ED technology have aided the rapid conversion of the African surface market.

Jan 1, 2004

By Paul Worsey, Delbert Da, Eric Achelpohl

The University of Missouri-Rolla is currently researching the concept of using glass microspheres in explosives as taggants as part of a 3-year technical project funded by the Bureau of Alcohol, Tobacco, and Firearms. These taggants are intended to provide two functions, first explosive detection and second post explosive event identification. The key priority is being able to detect explosives used in terrorist acts prior to detonation. The research on the use of microspheres includes the development of indicator taggants for the purpose of revealing the presence of hidden explosives, by either emitting radiation when bombarded with neutrons or emitting selective vapors, such as DMNB which may be readily “sniffed”. Of secondary importance, after an illegal explosion, the tags serve to identify the lot number, etc of the explosive. This information is to aid in the tracking, arrest, conviction and imprisonment of the perpetrators.

Jan 1, 2001

By David Willock, S. Singh, Michael Glogger

The efficiency of the loading system in a mine depends upon the characteristics of the muck pile, the loading machine specifications and the loading practices. The focus of this paper was to look specifically at the size distribution of blasted material, and to quantify its effects on loader productivity. A scale model of LHD was designed and fabricated to represent machines currently employed in the industry. The experiments were performed using crushed Gabbro, which was mixed in various proportions according to Rossin-Rammler size distribution to give five different characteristic particle sizes and five different size distribution constants for each characteristic particle size. The effect of the size distribution constant on peak and mean penetration forces, work done and bucket fill factor was examined. In addition, the influence of mean particle size, 80% passing size (D80) and % oversize on the penetration force and bucket load was investigated.

Jan 1, 2001

By Larry R. Fletcher, Virgil J. Stachural, Matthew N. Plis

The Bureau of Mines is conducting research on blasting methods that reduce highwall overbreak and the associated rockfall hazards. This paper presents the results of a series of tests to improve presplitting at a western surface coal mine. Reductions in overbreak were achieved by decoupling and/or repositioning the main explosive charge in the 10-5/8 inch presplit blastholes that formed the highwall. Blast designs are presented by the authors for 1) repositioning the explosive charge from a weak rock layer to a stronger rock layer, 2) decoupling with cardboard tubes in the toe region, and 3) suspending bagged powder at intervals along the length of the blasthole. About the same total quantity of explosives was used in all three test designs. It was readily apparent from periodic visual examination and photographic surveys of the highwalls that the amount of rockfall was reduced, and with a longer delay before rockfalls began, in all test areas.

Jan 1, 1991

By J Edmund Hay

Previous work by the Bureau of Mines to develop a test for determining the initiating strength of commercial detonators has been modified and extended. Recently reported results by the Bureau used a homogeneous liquid explosive to avoid the complicating effects of inhomogeneities; however, due to the belief that there may be essential differences between the initiation mechanisms of simple liquids and multi-phase mixtures and the fact that almost all commercial explosives are in the latter category, the experiments have been modified accordingly. The acceptor explosive is now a mixture of explosive-grade ammonium nitrate (AN) prills, methanol (MeOH) and nitromethane (NM). An additional change has been the use of the United Nations (UN) cap sensitivity test configuration in which the detonation witness is the degree of compression of a lead block, which is a quantitative measure of the response of the explosive. Results indicate that this mixture has sufficient range of sensitivities to be useful in comparing the strength of commercial electric detonators.

Jan 1, 1993

By John Wright

During June and July 1999 a United States Antarctic Program (USAP) team of three commercial divers and one blaster successMy removed an underwater rock obstruction which interfered with safe docking practices of research vessels that call at Palmer Station - the USAP research facility located on Anvers Island, Palmer Peninsula Area, Antarctica. Ordinarily, such a project might be considered routine. However, certain aspects of the project, particularly those dealing with logistics in a remote corner of the earth, sat3eguards for marine biota, and working underwater in the dark of the austral winter, conspired to make this project interesting. Even more challenging was ensuring the protection of the existing pier - a deeply corroded sheet pile structure backfilled with loose gravel and rock - which lay less than 50 feet away from the target obstruction, not to mention uncertainties at the outset as to the nature of the rock mass forming that obstruction.

Jan 1, 2001

By Thomas L. Linton

The results of an extensive literature review and field experiments regarding the effects detonation of high energy explosive have upon various aquatic organisms are reported. These results were used to modify regulatory permitting criteria in Texas. Three separate field experiments were conducted. In the first study, surface placed charges were used in a marine habitat. In the other two, the charges were placed in drilled holes. In one, which was in a freshwater environment, the drilled holes were filled with drilling mud after placement of the charges. In the second, which was in an estuarine environment the holes were allowed to sit for thirty days prior to detonation to permit natural back-filling to occur by water transported sediments. A variety of aquatic organisms held in wire cages were exposed to detonations. Immediate and long-term effects of the exposure were determined based on external and internal visual observations. Damage to aquatic organisms was found to be reduced by placing the explosives in drilled holes and back-filling the holes prior to detonation of the explosives.

Jan 1, 1997

By Mark S. Stagg, David E. Siskind, Stephen V. Crun, Willard E. Pierce

The USBM is studying the impacts of low-frequency blast vibrations on residences to assess both response and cracking potential. Complementing coal mining sites monitored in the midwest and east, vibrations were analyzed at a major construction site in southern Florida where potentially serious low-frequency blast vibrations were believed to exist.

Jan 1, 1996

By Kenneth Eltschlager, Steven V. Crum, David E. Siskind

The Bureau of Mines was funded by the Office of Surface Mining (OSM) to determine how blast vibrations from a local surface coal mine were affecting homes in the towns of Daylight and McCutchanville, located in southwestern Indiana near Evansville. Although Daylight was about two miles from the blasting and McCutchanville four to five miles away, many residents claimed that blast vibrations were damaging their homes. At least one citizen felt that the vibrations worsened at the time the mine began cast blasting.

Jan 1, 1992

By Christodoulos Xiouris, Ali Reza, James Karnesky

A rocket parachute signal flare is often used to signal a maritime emergency. In the general operation of these devices, a solid rocket motor propels a metal body to an altitude of approximately 1000 ft(305m).At the end of the rocket motor, a propelling charge drives a signal flare and parachute out of the metal body and ignites the flare, which then burns for approximately 40 seconds as it falls to earth. In this paper, we describe an engineering investigation of an accidental ignition of a rocket parachute signal flare, which caused injury to the user. The components of the flare involved in the accident were inspected via x-ray and microscopic imaging techniques, and compared with those of unfired flares recovered from the same vessel. Chemical analysis of residue on recovered components from the accident flare was also performed. These comparisons were used to determine the likelihood that the actuation mechanism had been deliberately manipulated. In the subject model of the flare, ignition of the rocket motor is accomplished through a percussion cap which is struck by a firing pin. Prior to activation, the firing pin holds down a pre-compressed spring. We present a comparison of the ignition system of the incident flare with those of other rocket parachute flares, which do not incorporate any stored mechanical energy.

By Riaan Van Wyk, Gys Landman

In today’s mining environment the use of radio communications in the form of two-way radios, cellular phones and even automated mining, form a vital part of the daily operations of a mining site. The radio transmissions that are used are a form of energy and as with all other types of energy it can have an influence on blasting equipment.

Jan 1, 2011

By Rob Farnfield, Ben Williams, Bob Woolley

This paper outlines how drilling safety standards are being driven forward in the United Kingdom’s surface mining and quarrying industry with developments in equipment, procedures and competence.

Jan 1, 2010

In the March/April 2006 issue of the Journal, we published an ethical dilemma called “Blowing the Whistle.” We received many interesting responses to the article as requested. Some of the responses are printed here. We’ve also included “Blowing the Whistle” again in this issue as a refresher on page 37. Dear Editor, It is in my own personal belief that it would be extremely important if I were the blaster to take the following steps. 1. Hold an immediate emergency meeting with the contractor to convince them to stop work at this point.2. This meeting would need to be held with all powers that be in this construction company. This helps eliminate the hearsay (excluding the farmer). 3. Explain the entire situation to the contractors as it has been presented to the blaster by the farmer. 4. Recommend calling in an engineering or geological firm with the expertise to investigate this matter immediately, and take all immediate action based on findings. 5. Follow up with farmer allow him to speak, (a.k.a. vent) and assure him proper steps are being taken to come to resolve this matter. 6. Be a good listener, and communicator with the farmer while investigation is being conducted. 7. Should the contractor not want, or take any of these recommendations, the blaster himself and his company should question even working for this company ever again. This in itself would not be the class of people we would want to be associated with EVER.

Jan 1, 2007

By Lawrence C. Schneider

In the past decade regulations governing the manufacture, distribution, storage, and use of explosives have proliferated. These laws have been developed by a host of federal agencies with no coordination. The result has been contradictory and impractical standards, which once adopted, are resistant to change or repeal. The current OSHA standards are one example which is examined in detail. The Commonwealth of Kentucky has made progress in modifying these standards, and still providing protection to the blaster and the public.

Jan 1, 1981