Search Documents

By Y. Foucaud, I. Filippova, L. Filippov

Flotation is the most common beneficiation route for tungsten ores, but the predominance of minerals with similar surface properties poses a real challenge. This study investigates the use of Falcon centrifugal separators for gangue minerals removal and desliming prior to flotation. A typical tungsten-bearing skarn ore (Tabuaço, Portugal) is used, containing scheelite (CaWO4) associated with dense calcium-bearing silicates (vesuvianite), fluorite, apatite and light silicates (feldspars) as gangue minerals. Two types of Falcon bowls (Falcon UF and Falcon SB) were used, prior to flotation tests with fatty acids as collectors and a combination of sodium carbonate and sodium silicate as gangue minerals depressants. This flowsheet was compared with a reverse configuration, using flotation prior to Falcon concentrator, and with a classical flowsheet, using hydrocyclone and flotation. Gravity pre-concentration and desliming with the Falcon concentrator were optimized through the design of experiments (DoE) methodology. The influences of pulp density, rotational speed, feed flowrate and fluidisation pressure (for the Falcon SB) were studied for both bowls. Results showed that the Falcon can be used as a desliming and pre-concentrating apparatus. Separation performances depend mainly on rotary speed and pulp density for the Falcon UF, whereas rotary speed and fluidisation pressure are the main parameters for the Falcon SB. With only one stage of Falcon SB, an enrichment ratio of 7.9 is obtained with a 65% WO3 recovery while 89% of apatite and fluorite are rejected, which constitutes a very good selectivity. In comparison, Falcon UF shows lower enrichment ratios, around 2.7. In terms of desliming, Falcon UF is as efficient as the hydrocyclone, while the Falcon SB is significantly more efficient. Hence, the use of Falcon SB prior to flotation improves the overall performance of the tungsten flotation route by desliming the flotation feed while pre-concentrating the scheelite. It impacts very advantageously the flotation, as most of the calcium-bearing minerals are eliminated. A Falcon SB stage prior to flotation yields a final concentrate grade of 29.7% WO3 with a recovery of only 36.8 % that should be optimized as the reagents dosages were not adapted to the pre-concentrated feed.

Jan 1, 2018

By Francisco Cubillos, Jorge Menacho, Cesar Gomez, Juan Rodríguez

Mineral flotation is the most used process to selectively separate particles of one or more minerals of interest. The process uses natural or induced hydrophobicity to collect particles on the surface of rising bubbles through collisions and formation of bubble-particle aggregates. Flotation machines must keep particles in suspension and well distributed, while at the same time, disperse a mass of air into a population of small bubbles. The efficiency of the separation depends primarily on the characteristics of the bubble population generated in the machine and its distribution and flow throughout its volume. The formation and separation of bubble-particle aggregates create two zones, with strong interactions between them, and with markedly different hydrodynamics conditions. A model describing two-phase hydrodynamics of the continuous and dispersed phases (frother solutions and bubbles, respectively), moving along the whole unit, is proposed. Bubble populations are characterized at the formation stage including the effect of the presence of frothers. Flow through the aggregates formation zone, where bubbles move freely and are closely spherical, is modeled using drift-flux analysis. In the aggregates separation zone, bubbles initially pack maintaining a water layer thick enough to prevent capillary forces to affect their shape. As water drainage proceeds, bubbles deform, capillary channels form, and a network of channels with a diameter size distribution develops; channels become narrower (permeability is reduced) as the distance from the interface increases. Froth hydrodynamics is characterized using models originally developed to describe unsaturated flow through porous solid particle beds. Effects of hydrostatic pressure are considered.

Jan 1, 2014

By J. A. Venter

Mineralogical studies indicate the Pt-Pd-Bi-Te class to react poorly on the flotation stimuli and indications are that these minerals are slow floaters. However, recent studies performed on a number of minerals from this class indicated strong interactions with potassium ethyl xanthate resulting in the formation of dixanthogen (only one of several xanthate species). The poor flotation response is not a result of poor interaction of xanthate with the surface. It is proposed that the oxidation products of sulfides in the process water interact with the PGM surface. To test this, the effect of thiosulfate (an important oxidation product of sulfides) was investigated by employing electrochemical measurements and FTIR spectroscopy. The electrochemical investigations indicate no strong effect of thiosulfate on the interaction of xanthate with the minerals surface as well as the reduction of oxygenthiosulfate is likely not responsible for the poor flotation response of these minerals in industrial plants.

Jan 1, 2014

By G. P. Wong

"The Inco Matte Separation process was the first commercial application using mineral processing techniques to separate nickel from copper from a slow-cooled matte in Sudbury since 1945. In Inco Sudbury operations, bulk sulphide concentrate containing chalcopyrite, pentlandite, pyrrhotite and some gangue minerals is flash smelted and converted to Bessemer matte. During the controlled slow-cooling of the Bessemer matte, discrete mineral grains of new mineral phases are formed: copper sulfide precipitates as chalcocite (Cu2S), nickel sulfide as heazlewoodite (Ni3S2) and a Cu-Ni-Fe alloy is also formed. Flotation is employed to separate Cc from Hz under high lime conditions (pH>12) with diphenyl guanidine (DPG) as both collector and frother.A simplified matte separation flowsheet is as follows. After grinding, the Cu-Ni-Fe alloy is removed by magnetic separation. All precious metals are recovered in the metallic alloy. Following the rougher flotation, a Cu concentrate is produced after cleaner and re-cleaner flotation in mechanical and column cells. Two Ni concentrates are produced: a high-grade Ni product containing less than 0.8% Cu from the scavenger column tails and a low-grade Ni product containing 5% Cu from the middlings circuit tails. A stream containing the inseparable Cc and Hz from the middlings circuit is generated and recycled back to the smelter. The quantity of this stream is typically about 3% of total feed and can be as high as 5%, greatly decreasing the overall matte separation efficiency. The large mass of the recycle stream is a direct result of poor Cc/Hz separation selectivity in the middlings circuit. The middlings circuit, consisting of a thickener, a regrind mill and two columns, processes two streams: cleaner tailings and scavenger concentrates. The thickener contributes significantly to oxidation due to the long residence time of the pulp in this unit."

Jan 1, 2003

By V. A. Ivanova, T. N. Perunkova, N. O. Dorozhanova, G. V. Mitrofanova

"Oxyethylated compounds are used as reagents-regulators in the flotation of non-sulfide ores, in particular, apatite-containing ores. Thus, the necessary degree of selectivity in the flotation separation of two calcium-containing minerals of apatite and calcite is achieved only by using, in addition to a collector, regulators-reagents from the nonylphenol ethoxylates class. In order to establish the most optimal structures, this paper presents a comparative assessment of the physical-chemical and flotation properties of several classes of oxyethylated compounds - alkylphenol ethoxylates, aliphatic alcohol ethoxylates and oxyethylated carboxylic acid. The authors have studied their dispergating ability with respect to the air phase and calcium soaps of the carboxylic collector. Dependences of foaming properties of regulators on the degree of oxyethylation have been determined. Adsorption isotherms of sodium oleate on apatite and calcite in the presence of regulators have been obtained. It has been shown that the presence of oxyethylated compounds in the solution reduces the amount of the adsorbed fatty acid collector. The influence of the considered classes of regulators on apatite flotation has been studied. The interrelation of flotation properties of oxyethylated compounds and their molecular structure has been established.INTRODUCTION Flotation plays a leading role in complex apatite-containing ores processing. However, two calcium-containing minerals - apatite and calcite, which compose apatite-carbonate ores, are characterized by close flotation properties. Selective separation of these minerals is a difficult task, the solution of which is impossible without using reagents-regulators. One of the ways to ensure the selectivity of the flotation separation of calcium-containing minerals is the use of reagents-depressants such as sodium silicate, starch, cellulose derivatives, and others (Liu et al., 2016; Rao et al., 1989). Another method is the application of nonionic reagent regulators (Filippov et al., 2016; Filippova et al., 2014; Ignatkina, 2017), which contribute to the adsorption of the ion collector (Filippov and Filipova, 2006 Rao and Forssberg, 1997) and stability of formed froth (Sis and Chander, 2003)."

Jan 1, 2018

By S. H. He

This paper focuses on the influence of pulp oxygen content on the separation of pentlandite and pyrrhotite contained in two different process streams in the Clarabelle Mill, operated by VALE INCO. The two process streams are (i) the scavenger cleaner feed, the product of regrinding the thickened, scavenged concentrate and the B cleaned tail produced from treating the non-magnetic fraction of the milled run of mine ore, and (ii) the magnetic concentrate which is the magnetic fraction of the milled run of mine ore. In the Clarabelle Mill, sulphite (SO32-) and TETA (triethylenete-tramine) are together used to selectively depress pyrrhotite from pentlandite. These depressants pre-ferentially decompose collector and/or sulphur enriched species at the pyrrhotite surface, an appar-ently essential mechanism in pyrrhotite depression from the scavenger cleaner feed stream. Selectivity in depression may originate from differences in the electrochemical rest potential of pyrrhotite and pentlandite. As both minerals are susceptible to oxidation, aeration in conditioning and flotation plays a key role in selective flotation. Important differences in the flotation behavior of pentlandite and pyrrhotite from the magnetic concentrate and the scavenger cleaner streams are highlighted in

Jan 1, 2014

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

The objectives of this study were to propose a viable alternative method for recovery of precious metals such as gold (Au), silver (Ag) and palladium (Pd) from waste printed circuit boards (WPCBs) and to regenerate the spent lixiviant solution for reuse. The proposed method generally consists of several steps as follows: 1). iodine-iodide leaching for metals extraction; 2). separation and recovery of precious metals and metal impurities from a pregnant leach solution; 3). regeneration of the spent iodine-iodide solution/lixiviant. In this method, more than 99% of Au leaching was achieved in the iodine-iodide solution from the solid residue of WPCBs that was obtained via sequential processes including incineration at 800 ?C and high pressure oxidative leaching with a diluted sulfuric acid at 120 ?C, while the leaching of Ag and Pd was less than 1%, respectively. Besides Ca, Cu, Ni, Co and Zn as main metal impurities, leaching efficiency of other metals did not exceed 1%. The precious metals and base metals as metal impurities present in the pregnant leach solution were separated and recovered by precipitation using L-AA and NaOH solutions. About 99.8% Au, 81.7% Ag and 72.8% Pd were recovered from the pregnant solution at pH of 2 with the addition of 0.1 M L-AA as precipitating agent. The remained small amounts of precious metals and metal impurities were precipitated at pH 13 using 1 M NaOH. The spent lixiviant after sequential precipitation was regenerated in the presence of hydrogen peroxide, hydrochloric acid and potassium iodide. It was revealed that over 90% of gold could be extracted from the residue of WPCBs with the regenerated lixiviant solution.

Jan 1, 2018

By Victor Avdokhin, Ivan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation.Catching coat is formed of natural magnetic and weak-magnetic placer minerals in field of magnetic system of the sluice. Magnetic minerals, placing along magnetic lines of force, form rough coat of fluffy structure. Size of the magnetic particles is chosen taking into account expected size of gold particles, which are to be fixed on the rough coat or between the magnetic particles. Changing coarseness of particles of mineral bed allows to regulate selectivity of recovering heavy minerals.Forming artificial fleece from magnetic minerals of initial sand, increasing capacity of the bed and relative hydraulic proportionality of mineral particles of the bed provide for the most effective recovery of fine gold."

Jan 1, 2003

By Kari Moen, John Rasmus Leinum, Jarle Hjelen, Terje Malvik

"Automatic identification and characterisation of mineral raw materials and beneficiated products are of major importance in mineral processing. However, minerals show great variety in their composition and physical and chemical properties. Industrial minerals may contain the same elements in about the same amount. In these cases backscatter electron imaging or chemical analysis are not sufficient to identify the minerals. Another problem arises when micro textures are not detectable in traditional imaging or the grain size is smaller than the X-ray spatial resolution.As a supplementary technique in these cases, application of crystallographic information by electron backscatter diffraction (EBSD) in the scanning electron microscope (SEM) may be a suitable method. By means of EBSD, diagnostic mineral information can be achieved if indexible patterns are provided.Until now EBSD has not been used frequently on geological samples for mineral and micro structure discrimination.The technique has been demonstrated on three Norwegian mineral raw materials and one Italian marble and shows that it has some advantages compared to traditional techniques."

Jan 1, 2003

By Jia Ma, Zhi-Chao Liu, Kang Liu, Chun-Feng Li, Bao-Bin Tang

"The geological environment of the certain uranium-molybdenum deposit is very complicated. While the study of process mineralogy is relatively few, which restricting the processing and leaching effect of ores. According to reaserch on process mineralogy of this mine, the basis of ore processing can be provided. The main contents of research are the uranium occurrence state and the influence of H2O2 in acid leaching. By various methods and experiments, the process of uranium mineralogical characteristics in this deposit are systematically studied. The results show that the uranium is mainly in the form of independent uranium minerals. The structures of these uranium minerals are venous and disseminated in mineral fissures, or microgranular inclusions in quartz and feldspar. It is not appropriate to concentrate the uranium minerals by flotation beneficiation because that the loss rate of target metals via water leaching process is very high. The ores are suitable for being acid leaching directly with 6% – 8% of H2O2, and the maximum leaching rate of uranium can be 96.88%. INTRODUCTION The uranium ores with associated elements have a large proportion in uranium resources (Lei, et al., 2014, Xing, et al., 2006; Ritchy and Wong, 1985). The uranium and molybdenum are easy to be paragenesis in nature enviroment because of their similar chemical properties. Therefor the uranium-molybdenum associated deposits are widely existing, such as the sedimentary sandstone uranium deposit in American with vanadium and molybdenum, the sedimentary sandstone uranium deposits in French with vanadium (Chen, et al., 2014; Lounis, 1997). A certain epithermal porphyry uranium-molybdenum deposit in China is mainly controlled by the subrhyolite- porphyry and the fault zone (Lv, 2012; Rui, 2010; Liu, et al., 2010). The ore properties of this deposit are complex, which include the high alteration degree, and the fine grain size of the target minerals (Ma, et al., 2013). The ore properties and occurrence state are quite different during each mining stage. As a consequence, the consumption of reagent increased and the leaching rate declined as long as the continuously mining. The author explored the best leaching rate of target elements According to the basic research on process mineralogy of present ores, experimental study of water leaching and oxidizing acid leaching on different particle sizes."

Jan 1, 2018

By C. B. Wu

This paper presents an analysis of comminution behavior of using cast iron segment (CIS) as fine grinding media with comparison to conventional steel ball. Grinding experiments utilize just one-size medium and mixed size media in laboratory were carried out and its efficiency is expected to be improved. The results show that no matter whether one-size medium or mixed size media employed, grinding efficiency of CIS media can be considerably equal to that of steel ball, on the other hand, grinding product by two kinds of media can conform to Robin-Rammler?s size characteristic curve and distribute in function of . )exp(100nbxy-= Comparing with steel ball, the milling capacity with CIS media could be increased up to about 8.6 percent, overcomminution decreased 3.96 in percentage and qualified size increased 3.98 in percentage in case of grinding fineness retained. At the same time, due to the improvement of grinding product size characteristic and its metal distribution characteristic, the grade and recovery of easy to separation size increased 0.24 in percentage and 6.47 in percentage respectively. Based on these results, the CIS media can be employed as novel fine medium for grinding process substituting for steel ball.

Jan 1, 2014

By J. Finch, F. Rosenblum, McGill University

The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to potentially hazardous to life and infrastructure. It is essential that there be a reliable test methodology that can categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral combinations making it difficult to predict their self-heating behavior a-priori based on mineralogy or with a simple "snapshot" test. Furthermore, self-heating behavior will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to predict the latent self-heating hazard of a sulphide material. Several of the methods were compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.

Jan 1, 2014

By L. Y. Wang

In order to produce the iron and steel products with high quality and decrease the output of steel tailings, the quality of molten iron is a critical factor for iron and steel companies, especially the content of sulfidic in molten iron. Hot metal pre-treatment, an important and effective method to desulphur, is widely used in steel production. Millions of tons of slag from desulphurization and slag skimming are produced each year in China, and many more times this amount is stored in slag dams because of the lack of effective means to deal with it. In order to achieve the goal of sustain-able development, recycling these slag becomes necessary. The main objective of this paper is to study the composition characteristics of slag that from desulphurization and slag skimming. The sample was obtained from Anshan Iron and Steel Group Corporation, processed by hot metal pre-treatment. In this study, the chemical components and the mineral compositions of sample were tested. The results of chemical components and iron chemistry phase analysis showed that the iron and sulphide content in this sample were high, and the iron products existed mainly in the form of magnetite, metallic iron, ferrosilite. X-ray diffraction (XRD) and scanning electron microscope (SEM) results indicated that the sample included metallic iron, ferrate, wustite, metasilicate, aluminate, aluminosilicate, white lime and soon. Grading magnetic separation test work showed that magnetic separation was an effective method to recovery iron products and decrease the sulphide content in concentrate, and the tailing could be used as the raw material or padding in cement production.

Jan 1, 2014

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By E. V. Zelinskaya

"Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production. Considerable attention in recent decades has been given to waste recycling. The task is to maximize the use of both newly formed and accumulated solid and liquid wastes. The mining and mining and smelting enterprises industrial waters are a very promising source of secondary hydromineralic raw materials. They have high concentrations of not only calcium, sodium, but also, for example, lithium, rubidium, heavy non-ferrous metals. In general, unfortunately, we have to state that today there is no wide practice of extracting valuable components from waste enrichment, as well as processing of man-made waters to extract metals from them. The quantity of extracted components from underground, and furthermore passing waters, is insignificant. At the same time there is a tendency to increased demand for rare metals: Sr, B, Br, I. This is explained by their wide use in many industries. For example, the consumption of lithium products is steadily increasing. The obtained results showed that in the liquid phase in connection with high salt content and a significant difference in the macro- and microcomponents contents, conditions are initially created for the microcomponents selective isolation possibility. The identified conditions realization is most possible in such technological processes as cryotechnology, sorption and ion flotation. There is an urgent need to expand research in this direction and to recognize as a publicly important task the mining and industrial waste processing full-scale introduction into the practice of operating mining and processing enterprises and iron and steel companies.INTRODUCTION Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production."

Jan 1, 2018

By G. K. Nimal Subasinghe

The establishment of grind size that optimally liberates the valuable mineral for efficient down-stream processing is of great importance for most mineral processing operations. Reasonably accurate comminution models as well as models of downstream separation processes may be found in the literature but their use in optimizing grind size is limited without an associated liberation model. In this work, an attempt has been made to address the above shortcoming by demonstrating how the effective parameters of the downstream flotation process may be predicted from the liberation characteristics based on the ore texture data for a disseminated nickel ore. In this regard, the liberation model based on linear intercept distributions of mineral and gangue proposed by King (1979) and its application to predict the flotation performance of an industrial plant demonstrated by Schaap (1979) may be considered useful contributions. However, while the model proposed by Schaap is simplistic enough, it is based on several assumptions due to the non-availability of intercept length measurements on the parent rock, in particular, on the extent of mineral exposure on the surface of comminuted particles. In this work, the linear mineral and gangue intercepts on polished specimens of a binary ore, comprising darker pentlandite as the valuable mineral and lighter barren host rock were measured using an image analyser. The resulting intercept distributions followed negative exponential distributions. Using the mean sizes of mineral and gangue intercepts, the proportion of liberated, compo-site and mineral occluded particles of a given size, the extent of mineral exposure on the surface of particles and their mean mineral contents were calculated using principles of renewal theory. The rock was then crushed and ground and different size fractions were floated. It has been shown that the parameters of observed recovery data based on 1st order kinetics such as the associated rate constant and ultimate recovery agrees well with those predicted from the quantities calculated above. This work has important practical implications since it can indicate variations in flotation performance arising from changes in mineralization within a large ore body.

Jan 1, 2014

By Ray Everson, Henry Kasaini

"We carried out adsorption experiments in chloride media to study the adsorption characteristics of Pd (II) anions on the surface of activated carbon. Throughout the experiments, we used commercial activated carbon pellets (0.8 Norit). The adsorption process was interpreted by using the ionisation and adsorption model. This implies that palladium anions were adsorbed physically on a protonated surface of activated carbon either as anionic complex species (PdCl4 -2) or aqua chloro-complex species [PdCl3(H2O)-] in acidic media. Furthermore, we established that adsorption of Pd (II) species was reversible at high chloride [Cl-1] concentration. The maximum adsorption capacity (Qsat) of Pd (II) anions averaged 27 mg/g. The Toth adsorption isotherms fairly predicted the equilibrium adsorption of Pd (II) species and the associated surface coverage.The effect of temperature and acid strength of the feed solution on the adsorption of Pd (II) ions were quantified. The adsorption kinetics was limited by external mass transfer since the effect of pore diffusion on the overall rate constant was negligibly small. A pseudo first-order kinetics model was used to describe the adsorption kinetics."

Jan 1, 2003

By I. Y. Titov, Victor D. Samyguin, A. Y. Nikitin

"It is suggested that improvement of separation process efficiency in machines and circuits of selective flotation should be based on application of the principle of technology individualization (PIT). This principle is grounded on the following provisions.The mineral composition of ores is used to establish the correlation between the selective reagent mode and the individual value of hydrodynamic conditions of flotation machines together with individual structure of the process flow diagram. The individuality of all sorts of particles identified by methods of process mineralogy was characterized by their distribution according to the rate of flotation (or spectrum). The spectrum identification is carried out by modeling and by experimental and computational method on the data obtained on various types of laboratory flotation machines.The computer-aided test is used to determine the optimal fraction distribution, which reaches the highest possible level of concentration data. The direction of hydrodynamic factors action on concentration data is estimated based on comparison of design base and experimental spectrum. The improvement of separation efficiency in devices is achieved in special-purpose flotation machines (SFM) the design of which provides optimization of hydrodynamic regime in spatially isolated zones. It is demonstrated that the main parameter of SFM operating mode individualization is the rise rate of bubbles going from the chamber into the froth. During this time the composition of particles optimum for separation is formed on its surface. Additionally, it is necessary to coordinate in the zones the residence time of pulp and foam streams with the air consumption. The improvement of separation efficiency in flotation process flow diagrams may be achieved by making several cascades with SFM installed in them. The individual effective structure of the scheme for a definite ores material composition depends on the ratio of particle varieties in the spectrum and is revealed by modeling."

Jan 1, 2018

By S. Carsten, S. Subramanian, R. Vasant Kumar, S. Vimalnath

"The effect of EPS components namely protein, polysaccharide and biosurfactant purified from Pseudomonas fluorescens was investigated for the bioremediation of Pb(II) ions in aqueous solution. Two parameters, namely the amount of EPS component and the concentration of Pb(II) ions were optimized for maximum Pb(II) ions uptake. The EPS components interacted with Pb(II) ions were characterized using energy dispersive X-ray analysis (EDAX) to ascertain the presence of Pb and by attenuated total reflection-Fourier transform infrared spectroscopy (ATR–FTIR) to reveal the functional groups involved in Pb(II) binding. The maximum Pb(II) binding capacities of protein, polysaccharide and biosurfactant were found to be 11.4, 0.55 and 0.11 mg mg-1 respectively. The biosorption processes followed the Langmuir model. The Gibbs free energy (?G0) values of -23.6, -20.9 and -23.2 kJ mol-1 for Pb(II) biosorption by protein, polysaccharide and biosurfactant respectively, attested to spontaneous, chemisorption processes. The ATR–FTIR results revealed the presence and involvement of amino, hydroxyl, carboxyl, phosphate, and methyl functional groups in Pb(II) binding and EDAX analysis confirmed the interaction of Pb with EPS components. The Pb(II) binding mechanisms of EPS have been discussed. The results demonstrate the potential of the purified EPS components of P. fluorescens for removal of Pb(II) ions from aqueous solution INTRODUCTION Waste water containing toxic metals from various industries pose a serious threat to human health and ecosystem. For treating such waste water, conventional methods like chemical precipitation, coagulation, evaporative recovery, electrodialysis, floatation, flocculation, ion exchange, reverse osmosis, nanofiltration, ultrafiltration are used (Lakherwal et al., 2014). These methods have some disadvantages like toxic sludge generation, incomplete metal removal and high cost (Singh and Gadi, 2012), necessitating the search for cheaper and efficient alternative methods. Bioremediation is one of the emerging alternatives where bacteria, fungi, yeast, algae and other biological substances are used as sorbents to remove toxic heavy metals (Vijayaraghavan, et al., 2015). Recently, the bioremediation potential of extracellular polymeric substances (EPS) of microbial origin has attracted attention. However, for Pb(II) removal, there is a paucity of literature focusing on EPS."

Jan 1, 2018

By B. Das

Waste water produced from coal preparation plants posses several problems during dewatering and solid/liquid separation. The natural sedimentation rate of the particles present in colloidal and finely divided suspended form is very slow. Flocculation technology is being applied in most of the coal washeries to recover water which is being accomplished through the use of inorganic salts, polymeric flocculants or both depending on the chemical and physical characteristics of the pollutants present in the waste water. The waste tailing water from Piperware coal preparation plant, Central Coalfield Limited (CCL), India, is highly turbid containing ~ 16000 NTU with negative surface charge in the pH range of 2 to 10. Polymeric flocculants in conjunction with fine magnetite is investigated to achieve faster settling rate with lowest level of water turbidity. The conditions affecting the interaction between the reagents and the turbid particles present in the tailings water are investigated. It is possible to bring down the turbidity of the water to < 90 NTU from very high turbid tailing water by using 2 mg/L of the polymeric flocculent in combination with 0.1 g/L of magnetite at natural pH of the tailing slurry. It has been found that finely divided positively charged magnetite particles in combination with the flocculent selectively coat the negatively charged impurities present in water and thereby increase the settling rate under the influence of a magnetic field.

Jan 1, 2014