Search Documents

By R. Shiva Kumar, G. Sreedhar, S. Sharma

Some of the Indian origin iron ore deposits located in Bellary, Karnataka province are having peculiar characteristics of Iron ore deposits (Hematite) having Iron above 64% and 30-40% lump (-30+6mm) recovery which are not suitable to use in blast furnace due to not meeting the specification of Tumbler Index and Abrasion Index. In general for high grade Iron ores, process flow sheet involves crushing and screening (dry/wet). In the contest of high grade Iron ores located at Bellary sector of Karnataka state in India, lump generated from this process could not attain the required physical properties (Tumbler Index, Abrasion Index) and metallurgical properties , even though the grade of the lump ore is above 64% Fe. Washing techniques like Drum scrubber and Log washer play major role in improving the metallurgical properties of Iron ore lumps by removing the light and hard layers of clay, silica coated over the lumps. In this study the effects were compared of drum scrubbing and log washing on iron ore lumps. It is found that by incorporating simple washing technique i.e. drum scrubbing or log washing, Tumbler Index of Iron ore Lumps could be increased from 74% to 78% which is acceptable for use in Blast furnace. From the Drum scrubber and Log washer tests, it is clear that Log washers have an edge over Drum scrubber in removing hard coated clay on surface of Lumps. This simple washing technique facilitate us to utilize the lumps directly in blast furnace and eliminate the unnecessary crushing and grinding of the ore so as to meet the specifications of Sinter fines and pellet feed.

Jan 1, 2014

By K. Saberyan

Zirconium and hafnium are two important elements in nuclear industries. Zirconium is used in fuel rod for its low neutron absorption. Hafnium should be separated from zirconium, because it has higher neutron absorption cross section. In this research, separation process of the mentioned elements from (Zr+Hf)Cl4 mixture produced in the Zirconium production plant (ZPP) of Iran (Esfahan) was studied employing solvent extraction method in the nitric acid medium by using tributylphosphate (TBP) as solvent, and kerosene as diluent. The effects of nitric acid, sodium nitrate and amount of extractant, zirconium concentration in aqueous phase, phase ratio, agitation time, and mixer agitation rate were investigated on the separation process. The process was optimized at 5 M nitric acid, 1 M sodium nitrate, 60% (v/v) TBP. The optimum values for phase ratio, agitation time and agitation rate were 1.5 min and 500 rpm respectively. In this condition, the zirconium extraction efficiency, and separation factor were 65.1% and 205.59, respectively. Finally, we accessed to nuclear grade in this research.

Jan 1, 2014

By Eduard Stefanescu, James M. Mwase, Egon Sehner, Stoyan Gaydardzhiev

"The study is focused on investigating the production of synthetic rutile of 95% purity or higher from a Norwegian ilmenite ore concentrate. This was to be achieved using a sequential process involving oxidative-reductive roasting at 975°C, followed by magnetic separation to further concentrate the sample and finally leaching with 20% HCl to remove mostly Fe-based impurities leaving behind synthetic rutile. The key process parameters considered were roasting time (1 and 2 hrs), leaching temperature (100, 125 and 145°C), pulp density (15 and 25wt%) and leaching time (3 and 6 hrs). The option of directly leaching the concentrate without pre-treatment was also evaluated. Test work was conducted using samples screened to a size fraction of 105-212 µm. Samples were leached in a 1 L glass autoclave. The reactor was hermetically sealed and thus the resulting pressure was not controlled but was dependent on the process temperature. The product from leaching was calcined and analysed via XRD and SEM to determine the purity of the product. The magnetic separation step was found to be ineffective and discontinued early in the study. Thus far a product with 97% synthetic rutile purity as analysed by SEM has been produced by directly leaching the concentrate at a temperature of 145°C, pulp density of 25wt% and leaching time of 6 hrs.INTRODUCTION The study investigates the use of a process route comprising oxidative-reductive roasting, followed by magnetic separation and then hydrochloric acid leaching and calcination to produce synthetic rutile from ilmenite concentrate. The grade of synthetic rutile produced should be suitable for chlorination to produce pigment grade TiO2. Hence the proposed process should produce a product consisting of no less than 95% synthetic rutile. Additionally, the product should have no more than 1.5wt% combined content of CaO and MgO (Zhang et al., 2011) as they tend to form high-boiling-point chloride leading to the malfunctioning of fluidized bed chlorinator (Cardarelli, 2008). Finally the product should have no more than 2.1wt% of Fe2O3."

Jan 1, 2018

By M. H. Moys, M. M. Bwalya

The use of the Discrete Element Method (DEM) to simulate the interaction of particles in dynamic environments is growing rapidly. This technique is also being applied in the study of milling extensively. However, to date more focus has been on the validation of the model. In spite of the advantages of the detailed information that is available from the simulator, appropriate application of this information remains a daunting task. In this paper a technique that combines particle breakage probability data with the energy spectra generated from the DEM is discussed.

Jan 1, 2003

By Frank van der Meer, Lea Quincke

"High Pressure Grinding is applied to achieve size reduction of the particles by inter-particle breakage and to generate micro-cracks in the product particles as a contributing factor in e.g. leaching or mineral liberation. As alternative to classification, a closed circuit operation for HPGR can be established by product recycling, where a proportion of the coarser edge material and parts of the center material are split-off to be recirculated to achieve a finer final (center) discharge product for subsequent processing steps as ball mill grinding or beneficiation. As a result of the product recycling, the content of fines in the feed material increases and may affect the grinding efficiency in terms of production of fines and the generation of micro-cracks in the particles. In the scope of this paper, the effects of the proportion of fines in HPGR feed on grinding efficiency and micro-crack generation were evaluated. Grinding tests were executed with different feed size distributions, from a fines-void situation (truncated feed) to a fines-abundant situation (high product recycle). The evaluation of grinding efficiency and generation of micro-cracks was done by particle size analysis, Bond Work Index tests, impact tests on HPGR feed and products, and X-ray computed tomography of single product particles. This publication summarizes the main aspects of the outcome of these investigations."

Jan 1, 2014

By Francisco Vicuña, Miguel Becerra, Nelson Iglesias

"The following article presents the development of a dynamic tool for the estimation of Jb/Jc rate (ball filling level / total load filling level) of a SAG mil operating in a single stage mode. Using the methodology detailed in this article, it is now possible to have a dynamic estimation tool in the operation, which enables strategic decision making and achieving a continuous development in process optimization. The estimating of the load filling level (Jc) was conducted using a power model, which in this case corresponds to the C-Model developed by (Morrell, 1993) that was calibrated by measuring the load filling levels (Jc) and balls (Jb) using the FARO laser scanning technology by means of Grind-Out and Crash-Stop procedures during the year 2013 and 2014. Finally, to estimate the dynamic filling level of full charge, Jc, three independent models were developed that allowed to feed the adjusted power model: •,SAG mill discharge grate slot wear model •,SAG mill internal volume wear model •,Ball filling level estimation model."

Jan 1, 2014

By B. McFadzean, K. Moller

"The mechanism whereby thiol collectors adsorb onto a mineral surface has been widely studied. Most of these studies examine the mineral surface at equilibrium state and, often, well above monolayer coverage. However, the formation of species at the mineral surface is a complex process that is both kinetically and thermodynamically controlled. In a typical industrial application, the dosage of collector will be around monolayer level. This study uses isothermal titration microcalorimetry to measure the heat evolved during the reaction of sodium ethyl xanthate (SEX) and sodium isobutyl dithiocarbamate (SIBDTC) and their mixtures with galena and chalcopyrite. The sensitivity of the instrument allows heats of reaction of sub-monolayer quantities of thiol collector to be measured.The study found that both the magnitude and kinetics of the reaction between a collector and a mineral surface was dependent on the type of mineral and the type of collector. Proposals are made for the reactions based on literature and the evidence from this investigation. It was found that when collectors were reacted with mixtures of galena and chalcopyrite, that the magnitude of the reaction was lower compared to that measured for the pure minerals alone. This may be due to galvanic interactions between the minerals, resulting in a passivating effect on one or both of the minerals."

Jan 1, 2014

By Manisha Singh, Manikanchan Sarkar

"Presently the global steel production is mainly based on iron ore sourced from high grade hematite deposits. India has large deposits of good quality hematite ore but with the prevailing practice, such deposits are depleting fast and getting exhausted. However, apart from such high grade iron ores, India is also endowed with large reserves of low grade iron ore, such as BHQ (Banded Hematite Quartzite), BHJ (Banded Hematite Jasper), BMQ (Banded Magnetite Quartzite) and Magnetite. In the present situation, it has become necessary to focus attention on upgradation of these low grade ores to produce useable concentrate. It augurs well that already substantial investigation work has been carried out in this respect and a few plants have been set up in India and abroad. One important aspect in this regard is the process route options with optimum yield and grade. Some of these low grade ores, particularly magnetite, are found to contain high phosphorous level, removal of which poses a major challenge. Since the grade is low, substantial upgradation necessitates fine grinding for appropriate liberation. Fine grinding is energy intensive and needs attention to achieve economy in this regard. Large quantity of tailings is generated in the process, wet disposal of which gives rise to a lot of hassles and hence, possibility of dry disposal of the same needs to be explored. The experience of the authors, with regard to aforesaid aspects which has been gained in course of carrying out relevant assignments is presented in this paper."

Jan 1, 2014

By J. D. Miller, C. L. Lin

In general, x-ray computed tomographic (CT) techniques are able to provide 3D images of the internal structure of opaque materials in a nondestructive manner. The unique cone beam geometry allows acquisition of all 2D projections with only one rotation of the sample thus providing for fast data acquisition and better x-ray utilization, as a complete 2-D detector array receives the cone-shaped flux of rays. Thus, an isotropic 3D volume can be reconstructed without the mechanical translation and the stacking of sequential slices as is the case for more conventional CT scanners. In this regard, a state-of-theart, custom designed x-ray microtomography facility to provide very detailed 3D spatial analysis of multiphase particles has been installed and is in operation at the University of Utah. The reconstructed 3D tomographic volume allows for an adjustable spatial resolution from 5 to 20 microns for sample dimensions from 10 to 40 mm in diameter, respectively. For example, a packed bed of coal particles is shown below in which different crystalline froms of pyrite are distinguished in 3D.

Jan 1, 2003

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisinger

"INTRODUCTIONThe objective of this work was to deport silver into a residue suitable for subsequent extraction without compromising the high base metal extraction during the pressure oxidation.RESULTS AND DISCUSSIONThe complex sulphide from the tailing pond of Cannington mine, Australia, was re-grounded and a bulk concentrate was recovered by flotation. The major economic sulphides are galena and sphalerite. The chemical analyses revealed 17.22% Fe; 4.88% Zn; 8.22% Pb; 9.49% S2- and 422 g/t Ag. The baseline cyanidation yielded 36.60% of silver at high cyanide consumption (24.17 kg/t NaCN). Pressure oxidation at 150°C (in the absence of iodide), followed by cyanidation of the residue yielded 8% silver extraction. Pressure oxidation was carried out at 110-150°C in sulphate media with additions of potassium iodide and the resulting residue was subjected to cyanidation. High recovery of silver was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured (Figure 1). Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of leadhydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the slurry."

Jan 1, 2003

By Kobus (J. J. ) Rossouw, P. Chris Pistorius, Johannes Sono

"Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. The tests served to evaluate both the reduction rate (during direct reduction) and the dissolution rate of carbon from the coal into an iron bath.Reduction rates of mixtures of magnetite and devolatilised coal were assessed isothermally, using samples of 55 grams. The off-gas analysis was used to follow the extent of reduction. Results are shown in Figure 1 a). Coal B was expected to be more reactive, based on its higher content of reactive macerals (77%, compared with 61% for Coal A). In line with this, Figure 1 a) does show a higher reduction rate with this coal. However, increasing the reduction temperature increases the reduction rate substantially,especially for the less-reactive Coal A.For the dissolution experiments, samples (mass: 250 g) were melted in an alumina crucible (under a nitrogen atmosphere), to give a starting composition around 1%C. When the desired temperature was reached, 25 g of char was added on top of the melt, through a feeding port. Results are shown in Figure 1 b). The more-reactive Coal B was less crystalline (the graphite crystallite size estimated from X-ray diffraction was 4.6Å, compared with 11.4Å for Coal A). This is associated with a lower dissolution rate in iron."

Jan 1, 2003

By Sergey Gudkov, Yuri Yemelianov, Stanislav Balikov, Andrey Boldyrev, Andrey Bogorodsky

"The results of POX of refractory gold-bearing concentrates using halide-ion as a lixiviant for precious metals and activated carbon as an adsorbent are given. It was found that gold did not recover to the solution when halide was added during POX. Silver partially dissolved in the solution. When halide-based reagents and activated carbon were added during POX, gold dissolved and loaded onto the activated carbon. The degree of sulfides oxidation was 99.3-99.6%. The recovery of gold onto granulated carbon was 94.7-94.8% when using chlorine-bearing lixiviants: NaCL, CaCL and carnalite and 98-99% when using KJ and KBr. This treatment process of refractory gold-bearing concentrates combines sulfide oxidation, dissolution and adsorption of precious metals. The results of the metals recovery achieved using this process can be compared with the recovery during POX-cyanidation. In this case, sodium cyanide was not used. This allows the reduction of capital and operational costs due to the absence of cyanidation, CIL and detoxification of leaching tailings circuits."

Jan 1, 2014

By Joseph Kelly, Christopher Kelsey

This revolutionary super-fine crusher has the unique capacity to generate fine and ultra-fine products from single stage reductions of coarse or fine mineral feeds. The crusher consists of a rotating compression chamber and an internal gyrating mandrel. The axis of rotation of the shell is displaced relative to the axis of the vertically mounted mandrel. The inner surface of the compression chamber is machined as double cone frustums at an angle equal to the displacement angle. Crusher feed is accelerated into a compacted particle bed, which lines the inside of the compression chamber. The depth of the compacted bed progressively increases until the mandrel is engaged. The mandrel is then free to rotate with the compression chamber. Continued feeding increases power draw and triggers the counter rotating mandrel gyration drive. The gyrating mandrel delivers multiple compressions at high pressure to the rotating particle bed. High concentrations of energy are harnessed within a small active volume over short retention times. The combination of extraordinarily high power intensity and extreme compressive force results in primary compressive fracture and induced secondary tensile failure. The axially displaced rotation of the compression chamber effectively distributes the breakage forces throughout the particle bed. This paper covers open circuit, pilot trials on magnetite, perlite, garnet, marble and a copper/pyrite concentrate. Particular emphasis is placed on the extraordinary results achieved with trials on zircon and highly refractory fly ash. The extreme duties were deliberately chosen to demonstrate the crusher’s application scope and potential to impact capital operating and maintenance costs as the technology matures. Super-fine crushing, once considered impracticable has the potential to offer compelling options for the generation of ultra-fine products.

Jan 1, 2014

By Sebastian Fredes, Williams Calderon, Mauricio Toledo, Gonzalo Montes-Atenas

The influence of the temperature on leaching kinetics of copper-bearing minerals has been widely acknowledged: the leaching of copper oxide ores is generally described as exothermic reactions while copper sulfide ores are associated with endothermic reactions. Reports studying the influence of temperature on leaching kinetics at laboratory scale frequently involve the implementation of either fully flooded isothermal systems or jacketed column setups. Nevertheless, at industrial scale controlling or monitoring the temperature or temperature changes is almost impractical. In fact, leaching process is usually a large tonnage operation and changing the temperature of vast amounts of material would require an enormous amount of energy and highly specific heat transfer equipment. Preliminary computations on the amount of energy required to increase the temperature of a heap or dump in 1°C indicates that it would be impossible to find an energy source able to accomplish the task. In order to provide a solution to this matter it is suggested to create an energy managing protocol (EMP) that permits heat up or down the porous body locally taking advantage from the temperature gradients and from the reactivity of different regions within the material as a function of the leaching cycles. The aim of this study is to evaluate different heat transfer regimes in a 1 ton pilot column leach operation. It was found that best results of copper recovery are obtained when heating up the column in horizontal bands starting from the top of the column moving downwards as the leach cycle evolves. The system is expected to be suitable for industrial applications, but further development of the technique is required, particularly in the design of the heat transfer dispositive.

Jan 1, 2014

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Xanthates (dithiocarbonates) have been the collector of choice for the flotation of sulfide minerals ever since the flotation process was developed and have been studied quite extensively. Recently, trithiocarbonates have been shown to be very effective in bulk sulfide bench-scale flotation. Fundamental analysis using electrochemical techniques have supported these bench-scale results, illustrating that the trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates, than the dithiocarbonate (DTC) collectors, as is shown in Figure 1.

Jan 1, 2003

By A. Gueciouer, A. Akkouche, K. Chalah, A. Benmounah

"Drilling solid waste is a typical industrial solid waste, and it is a major pollutant source to ecological environment. Generally, waste management dewatering systems separate solids and fine particles from the liquid phase of drilling fluid, thereby leaving a clarified aqueous solution and allow the cleaning of waste fluids. Typically, dewatering waste management systems clean drilling fluid through coagulation, flocculation and/or mechanical separation. Chemicals used in dewatering are based on the coagulation-flocculation process, which it facilitate the removal of suspended solids and colloidal particles. The factors which can promote the coagulation-flocculation are velocity gradient, contact time, and PH. The objective of this work is to optimize a formulation adequate for dewatering based on the coagulation-flocculation process used coagulant (Aluminum sulphate), anionic flocculants (Partially Hydrolyzed Polyacrylamide) and anionic polyelectrolytes (in solid form with linear chain with very high molecular weight). The results obtained show the good efficiency of the coagulant and flocculants. INTRODUCTION Rig site dewatering of drilling fluids with recycling of processed water can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste [1]. To improve the dewaterability of sludge, different pretreatment processes have been widely studied and developed including thermal, chemical, magnetic, mechanical, acoustic, electric, electro-acoustic and their hybrid treatment processes [2]. Rig site dewatering (figure 1) is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. Coagulation occurs when the solid and allowing it to be attracted to other solids by van der waals forces. Flocculation is the binding of individual solid particles into aggregates of multiple particles. It is physical, rather than electrical, and occurs when one segment of a flocculating polymer chain absorbs simultaneously onto more than one particle [3]."

Jan 1, 2018

By Majid Saghaeian, Rasool Hejazi, Parisa Ghobadi

"Pulp handling in mineral processing circuits is very complicated due to its inherent different specifications compared with other fluids such as water. Because any variation in ore property (e.g. size and abrasion index) and pulp specification (e.g. density, solid content and pressure) causes problem in this part and reduces the plant availability and throughput as a result. The most common issues in the hose system are sumps and pipe-line blockage, wearing of the pumps impeller and liner, and pipe tearing specially at elbows and bends. High pressure grinding roll (HPGR) is employed in a closed circuit with a screen as the first stage of grinding in Zarand Iranian Steel Complex (ZISCO). Wearing of the pump and pipeline transferring the screen undersize stream was the main problem from the plant commissioning. The plant couldn't achieve to the design capacity because of this defect. Although various practical solutions such as improving the pipes and impeller material quality and eliminating the elbows, as much as possible, were done in order to downtime minimizing, but damages didn’t vanish. Since HPGR discharge contains somewhat rough and abrasive particles, the mentioned modifications didn't effective very much. Therefore, converting of the wet screen to dry and using of belt conveyor to the screen undersize handling was employed based on the plant capability evaluation and experimental and pilot trial results. Although this reformation imposed another additional cost (for conveyor system), but it had significant advantages such as increasing the plant availability up to 96%, reducing the operating costs of the wear parts, providing more stable operating condition for the HPGR performance and decreasing abrasion rate of the HPGR rolls liner because of the lower moist feed."

Jan 1, 2014

By Markus A. Reuter, Albert Scholte, Ewoud V. Verhoef, Gerard P. J. Dijkema

"A dynamic, interactive map has been developed of the life cycle of a number of metals, from mining through to minerals processing, metal production, product manufacturing, recovery and waste management. Whilst the existing metal process network and waste management infrastructure provide substantial scope for (product) design, these also limit change because of the strong path dependency of industry and infrastructure development. The metal production network is complex, as it consists of an interconnected and integrated system that incorporates multiple production routes for a spectrum of metals. More often than not, the production or recovery of a single metal is related to or dependent on the generation or recovery of another. The effects of these other metals is of great importance. In order to realize the potential economic importance of impurities, research and development have integrated the processes of copper production with those of lead and zinc, and connected the processes to those of among others silver, bismuth, tin and platinum group metals (PGMs), for example. The recovery of these elements from the interconnected circuits is extremely complex, as most of the elements must be circulated between two or more circuits before they are concentrated enough to make their extraction possible, and their recovery as a compound profitable.From such a system’s perspective, it can easily be seen that a complication for solid waste management has arisen through the development of products (consumer goods) that bring together metals that are not linked in natural resources. As a consequence, many of these materials are not compatible with any process in the metals production network that was developed for the processing of primary, natural resources, optimized for the processing not only of the primary metal but also for all mineralogically associated minor valuable and harmful elements. The formation of large or complex residue streams or undesired harmful emissions then inhibits processing and recovery of said products at their end-of-life. Another complication is that any change to the system (in metal production, SWM or product design) affects the system configuration. Due to the changing demands for metals as a result from the changing products made from the metals for example, the relationships between the processes in the interconnected metal production systems change. This affects both the demand for old scrap (required amount and grade) from waste management, and the environmental profile of the metals. Preferably, therefore, product designers, waste processors and metal producers must cooperate to realize optimal metal recovery in processing discarded consumer products."

Jan 1, 2003

By Sonia Helle, Ursula E. D. Kelm

"From a metallurgical point of view, acid leaching of oxide zone copper ore is considered in the first place in terms of ore grade, whole rock mineralogy, rock granulometry, crushed aggregate size distribution, porosity, permeability and corresponding fluid flow characteristics. Despite exhaustive physicochemical and general mineralogical characterization, drops in copper recovery occur and are often attributed to and “unquantified mineralogical misbehaviour” of the gangue phases. This study establishes an experimental link to monitor and quantify the chemical interaction of chrysocolla, malachite and atacamite with reactive gangue phases.Laboratory-scale sulphuric acid (15%) leaching in small columns is carried out using a synthetic rock composed of 57% quartz, 1% ore phase, and 42% reactive gangue. Gangue phases were selected to represent mineralogy found in argillic, advanced argillic, and propylitic alteration zones. Exotic copper ores of Codelco Norte (in particular Mina Sur) served as model for the modal distribution of mineral phases. Natural reactive gangue phases (<200 Tyler mesh) were chosen as pure as possible: Saz-1 and Swy-1 montmorillonites, KGa-1B and KGa-2 kaolinites (all Clay Mineral Society, USA, Source Clays) Nau-2 nontronite, Imt-1 illite (both Clay Mineral Society Special Clays) and Chilean mordenite, laumontite and bentonite. Ore phases are: mineraloid chrysocolla from Radomiro Tomic (Codelco Norte), reagent grade malachite and a purpose synthesized atacamite-paratacamite mixture. Complete chemical, physicochemical and mineralogical characterizations were carried out for ore and gangue phases.The following observations hold for samples with and without mineralization: Smectite-rich gangue increased up to 75% in volume. Once wet, air-filled vesicles formed due to the rapid sealing effect of overlying smectite in the column. No volume change occurred for illite, mordenite and kaolinite gangues. For kaolinite mixtures acid puddles formed on top of the column during initial leaching due to the delamination and barrier formation of this phyllosilicate. Fluid recovery was <60% for expandable phases and reached up to 80% for non-expandable mixtures. These observations confirm the very low extractions obtained in ore with a combined smectite – kaolinite gangue for Mina Sur. The most important mineralogical changes observed in the solid residues are: reduction of basal smectite phase reflections (XRD), and slight loss of illite intensities. This is also reflected in the major element composition of the residues, which demonstrate a loss of Mg, Mn, Ca, Na, K followed by Fe, Al and Si; with their proportions depending on the starting materials. Furthermore, alunogen and meta-alunogen formed, with related phases coquimbite (illite) and godichite (nontronite) also depending on gangue mineral chemistry. For laumontite samples, meta-alunogen and alunogen precipitated from the leachate."

Jan 1, 2003

By Heinrich Hutchison, Thomas von Moltke, Roelof F. Sandenbergh, Katarina P. Cerovic

Although the cyanidation process for gold leaching has been applied for more than a hundred years, some aspects of it, such as the passivation of the gold and the depassivating action of heavy metals, are still not well understood. In this work the anodic behaviour and surface composition of gold in alkaline aqueous cyanide with lead additions were investigated using polarization experiments and XPS. It was found that lead in the solution activated the gold at low concentrations, somewhat more positive than the reversible potential for gold, but that the activity again decreased at higher concentrations of lead. The potential range for the activation of the gold coincides with that where underpotential deposition of lead occurs, i.e. –200 to –600 mV(SCE), as indicated by the surface composition of the gold, shown in figure 1. Note that the concentration of lead on the surface of the gold only increased with time in the bulk plating potential range for lead, where gold is not activated by the presence of lead. It is also shown that up to 20 mg/L of lead added to the solution will activate the gold, provided that bulk plating of the lead is avoided. It is also important to avoid reducing conditions during leaching, where bulk plating of lead may occur, if the gold is to be activated by lead to achieve a high leaching rate, as the bulk plated lead screens the surface rather than activating it.

Jan 1, 2003