Search Documents

By Wu Jian-tao, LI Guo-wei

"The Cement Mixing Pile (CMP) quality assurance assessment is an important programme in evaluating the efficiency of foundation improvement. Coring is the current specified method of quality assessment in China which has the shortcomings of long cycle, high cost and low efficiency. The field and laboratory test show that the regular cone penetration test can only detect maximum of 4m of effective detection depth in CMP. In contrast, the method of cone penetration test in the reserved hole can detect the quality continuously along the pile at any depth. The tip resistance of reserved hole penetration in the 7th day has good linear relationship with unconfined compressive strength in the 28th day. The slope of linear relationship decreases with the increasing of clay particles content.INTRODUCTIONThe method of Cement Mixing Pile (CMP) is often used to improve soft soil foundation in highway construction, with the major purpose of reducing settlements under embankments (Bruce et al., 2000),which is a form of what is known as the Deep Mixing Method (Bruce et al., 2013). The CMP technology spread quickly in China in the 1980s. CMP quality assurance assessment is an important programme in evaluating the efficiency of foundation improvement. Coring is the current specified method of quality assessment in China (China Academy Of Building Research, 2002). The method of Coring is perceived in some quarters that samples will provide lower strengths given the distress caused to the core during drilling and extraction (Bruce et al., 2002).The cone penetration test CPT can provide continuous measurements of the penetration resistance, sleeve friction at the tip of the probe, which has advantages of simple operation, low cost and high efficiency compared with coring. However, CPT tests have not been established to assess CMP in Sweden because of difficulties in maintaining verticality (Larsson, 2005). In Finland and Norway, however, CPT tests are commonly used (Halkola, 1999). One of the disadvantages of CPT is the tendency of the cone to steer out of the column (Porbaha et al., 2003). Darya Mokrousova (2010) states this tendency to deviate can be overcome by pre-boring and starting the penetration test from the base of the pre-bored hole. Sheng Haiyang (1999) found that probes may be deflected out, sometimes even at small penetration depths, and may not give a complete inspection of the pile. Liu Songyu et al. (2003) suggested that the Standard Penetration Test (SPT) is an effective way to evaluate the strength and quality of stabilized soil-cement columns. In general, Regular CPT can’t test the full length of CMP, and SPT still needed drilling which causes discontinuous detection. From the existing standard of China, core sampling compressive strength test is the main method, evidently, coring displays a longer test cycle, high cost and low efficiency. Therefore, an improvement of CMP quality assessment, by conjuring a fast and reliable detection and evaluation method, is necessary. The aim of this paper is to research the feasibility of using CPT in assessing the quality of CMP and presents an improved CPT method."

Jan 1, 2015

By Thang V. Nguyen, Lisheng Shao, Gary E. Taylor

"The Community Memorial Hospital of Ventura, California, proposed to build a new state-of-the-art Cancer Treatment Center with radiation shielding walls and roof. The loose silty soils at the site had the potential to liquefy during an earthquake, which would result in significant settlement under the heavy footing loads. Treatment options included various deep foundation alternatives, as well as several ground improvement methods. The choice of wet soil mixing minimized the disturbance to the adjacent hospital during construction and potential settlement. Wet soil mixing allowed the structure to be supported on a raft foundation, meeting the stringent building total and differential settlement criteria. The authors also performed unit cell 3-D finite element analyses to evaluate the behavior of the wet soil mixing system in seismic loading conditions. This paper highlights the ground improvement design, construction, QA/QC, and the research related to evaluating the effectiveness of soil mixing for liquefaction mitigation.INTRODUCTIONThe Ventura Community Memorial Hospital proposed the construction of a new Cancer Treatment Center to replace the existing structure, which was built in 1901. The hospital complex is located in a wellestablished residential neighborhood. The soil conditions at the site of the proposed structure required ground modification to support the very heavy radiation treatment section of the building and limit settlement. Originally, 90-foot-long precast piles were considered for foundation support. Based on supplemental Cone Penetration Tests (CPTs) performed, the deepest CPT did not encounter competent pile bearing strata at a depth exceeding 30.5 m (100 ft). This could result in failure of the piles under long-term conditions, especially if hydro-consolidation occurs. The more realistic pile penetration depth would have been 36.6 to 45.7 m (120 to 150 ft). In addition, the excessive noise in association with pile driving would have been unacceptable to the community, patients, and staff of the hospital, so an alternative ground improvement solution was required.The specialty geotechnical contractor recommended wet soil mixing, an economical solution of creating a soil-cement product known as soilcrete that would significantly reduce the construction related noise and provide a more complete deep foundation for the structure.SOIL CONDITIONS AND SETTLEMENT CONCERNSThe subsurface soils were interbedded (Fig. 1) consisting of loose to medium dense silty sands, and soft to medium stiff silty clays to a depth of 30.5 m (100 ft). Groundwater was encountered at depths of 9.1 m (30 ft) and historical high groundwater was at 8.5 m (28 ft) below the ground surface."

Jan 1, 2015

By Manchanda H, Agarwal J.

The construction industry has one of the largest numbers of injuries compared to other industries. Thus, reducing accidents and determining construction risks are extremely important. One of the essential steps for construction safety management is hazard identification and risk assessment, since the most unmanageable risks are from unidentified hazards. While the urban rail transit systems are being developed rapidly in almost all major cities of India, adjoining Existing Building Structures and historic sites are facing possible threats of unexpected damages and accidents. The protection of these structures becomes one of the major challenges specifically when the infrastructure being developed involves construction of underground tunnels passing through old cities. The assessment of settlement induced damage on buildings during the preliminary phase of tunnel excavation projects, is nowadays receiving greater attention. Analyses at different levels of detail are performed on the surface building in proximity to the tunnel, to evaluate the risk of structural damage and the need of mitigation measures. The current paper presents current practices being adopted in India for prediction and excavation of tunnelling induced ground movement and building damage risk-assessment. The paper highlights empirical and numerical approaches towards predicting settlement induced damages on buildings during the tunnelling, detailed step by step methodologies for conducting building condition surveys, evaluating associated hazards, and adopting adequate building risk identification and mitigation methods. The paper also discusses associated technical and contractual challenges and highlights way forward to overcome them.

Sep 1, 2022

By P. J. Nicholson

The methods of reinforcement to be discussed in this paper are all insitu methods, ones that can be used on the soil structure as it exists in the ground, and do not rely on excavation and replacement of the soil. Current practice in the United States, as well as new ideas and methods, will be discussed as they relate to slope stability, retaining walls, and to other uses such as control of mine or cavity related subsidence and to liquefaction control under existing structures. The method is based on the concept of "nailing" or reinforcing the soil in place, and thereby causing a mass of soil to act as a coherent unit. When performed properly, a true gravity structure can be constructed, one that will remain intact under both horizontal and vertical loadings and that will also resist vibrational and seismic loadings.

Jan 1, 2010

By Shyam Chengalath, Johan Jeansson, Magnus Hörman

Down-The-Hole (DTH) drilling usually uses compressed air to power the hammer. However, there are now DTH hammers on the market which instead of compressed air use high pressure water to power the hammer. There are several benefits with using water DTH compared to air DTH, which are discussed in more detail in this paper. From a physics point of view many of the benefits arise from the fact that water is an incompressible media and air is not. Energy consumption is roughly a quarter compared to air, resulting in lower carbon emission and a lower energy bill. In the case of water DTH the water leaving the drill bit in the hole is at a low velocity and ambient pressure. However, with air DTH the air leaving the drill bit in the hole is at a high velocity and high pressure. This means that the risk of damaging surrounding structures in sensitive areas such as urban environments and dams, is greatly reduced with water DTH. In this paper two cases where water DTH is used in jet-grouting applications are discussed in detail. As these cases show there is a clear improvement in productivity when using water DTH hammers.

Sep 1, 2022

By Alexander Ciccone, John H. Gill

Jet grouting is a highly versatile ground modification technique that can offer significant commercial and technical advantages over traditional concrete pit underpinning applications. Despite these advantages, jet grouting remains an underutilized technique in the construction industry due to its perceived complexity, cost, and risk. When performed thoughtfully, underpinning by jet grouting offers significant safety and schedule advantages over traditional underpinning approaches. The New England construction market has seen a recent acceptance in the use of jet grout underpinning on congested project sites across a variety of subsurface conditions. The reduction of the cement batch plant footprint due to equipment advances has allowed the use of this technique in urban sites where its use would be previously infeasible. Furthermore, jet grout underpinning has been utilized for support of historic and sensitive structures with generally lower tolerance to settlement than is typically feasible with conventional pit underpinning. Robust, real-time geotechnical instrumentation monitoring systems have helped reduce the uncertainty and further expand the feasibility of jet grout underpinning applications. When properly designed and constructed by qualified and experienced jet grouting contractors, the flexibility of soilcrete for design and construction may be utilized to overcome the many inherent challenges which complicate underpinning and earth retention systems. INTRODUCTION The construction of buildings and infrastructure in our increasingly dense urban spaces often requires excavations below the elevation of existing structures immediately adjacent to the proposed work. Where a proposed excavation system encroaches into an existing structure’s zone of influence, additional measures, such as the construction of an underpinning or excavation support system, are required to safely excavate and minimize the impacts on the adjacent structures. Jet grouting is one method of underpinning that offers significant commercial and technical advantages over many other techniques. Though it was first used to the United States in the 1980s and has grown in popularity elsewhere, jet grout underpinning remains underutilized domestically due to its perceived cost and risk premium. Jet grouting has significant technical advantages over other underpinning methods due to its applicability in a wide range of soil types and its flexibility of design and installation. The jet grouting process is capable of limiting the movement of foundations during construction and excavation to lower thresholds than most traditional underpinning methods (Droof, Furth, & Scarborough, 1995). Its use for underpinning historic and sensitive structures with lower settlement criteria provides additional evidence to its technical utility. Through thoughtful design, adequate planning, and experienced installation, jet grouting can be an appropriate underpinning solution that can provide significant cost and schedule savings.

Jan 1, 2019

By David Guy, John Stanbury, Gilbert Tallard

"In 2009, storm surge from Hurricane Sandy inundated the Bay Park Sewage Treatment Plant located at El. +4 to +12 (+1.2 to +3.6 m) in East Rockaway, Long Island, NY. With all systems down, raw sewage water mixed in the floodwaters. A recurrence of such an event being unacceptable, and in view of rising future sea levels, a flood protection project was developed by Nassau County with funding coming in large part from the federally funded Sandy Rescue Fund. Designed by Arcadis/Hazen & Sawyer Engineers J.V., the protection took the form of a perimeter barrier capable of withstanding future storm surge. Due to limitations imposed by property lines and existing facilities, a levee design with three different types of cross section was developed to adapt to each location, adding construction complexity. The Long Island subsurface is characterized by beach sand extending to great depth. The clay required for the core and levee cover therefore had to be brought in from out of state. A thin silty clay layer at El. -23 to -25 (-7.0 to -7.6 m) served as an aquitard. The under-seepage was reduced by a hanging cut-off wall designed as a vibrated beam thin wall and filled with a salt water resistant, low permeability, self-hardening slurry.INTRODUCTIONOn October 29, 2009, Hurricane Sandy hit New York City, with a devastating effect on the region. The low lying Bay Park Sewage Treatment Plant (STP) (Fig. 1) serving Nassau County on Long Island was submerged (Fig. 2). All basements and underground mechanical facilities were flooded (Fig. 3) and millions gallons of effluent were released into the waters of the nearby Hewlett Bay which connects via other small waterways to the Atlantic Ocean."

Jan 1, 2016

"Standing 92 stories high and just over 1,362 ft tall, Chicago’s Trump International Hotel and Tower is perfectly positioned at the center of one of the world’s most impressive skylines.The Tower serves as a link between its famous predecessors, Willis Tower (formerly, the Sears Tower) to the south and the John Hancock Building to the north. Originally planned to be the world’s tallest building, the project was scaled back when the developers started questioning the need for super-tall buildings after the September 11, 2001 terrorist attacks. In its River North neighborhood, Trump Tower dominates the skyline as a symbol of Chicago’s last great building boom, standing triumphantly over other high-profile projects that have been postponed due to current economic realities.It is often said that the three most important factors in real estate are location, location and location. This maxim was not forgotten by The Trump Organization when the site was selected for the International Hotel and Tower. Located two blocks west of Michigan Avenue and Chicago’s famed Magnificent Mile, the site is bound by the historic Wrigley Building to the east, Wabash Avenue to the north and west, and the Chicago River to the south. The building’s position along a bend in the Chicago River allows visitors and residents unobstructed views to the mouth of the Chicago River and Lake Michigan. Site ChallengesUnderneath the site there are approximately 10 to 20 ft of sand and urban fill underlain by soft Chicago blue clay. At 75 ft in depth, the soft clay transitions into Chicago hardpan, a very hard till that was consolidated by the glaciers over 10,000 years ago. Below the hardpan, the till turns granular with cobbles, boulders and water under pressure. Bedrock is about 100 ft below existing grade and has a weathered surface with fractures and clay seams. Unweathered limestone bedrock is sound and hard with unconfined compressive strengths of 10,000 to 20,000 psi."

Jan 1, 2009

By Negin Khalili-Motlagh-Kasmaei, Paul O'Leary, Christopher J. Rothsiedl, Dimitar Ninesvski, Alexander Zöhrer, Vincent Winter

This paper presents the implementation of a digital twin for the vibro-replacement ground improvement process, as part of a digital construction site. The goal is to implement an evidence-based quality assurance for each produced element (column or point). The system uses a combination of planning data and real-time machine data collected automatically from construction equipment. In addition to the quality assurance, feedback is provided in a number of areas, e.g., condition monitoring of the equipment. The digital twin builds upon the real-time sensor and machine data, fused with metadata, to implement a digital model for the process. A hierarchical data evaluation, using rule-based Key Performance Indicators (KPIs), permits viewing of the spatial variation of data over the construction site. This permits the modelling of systematic variations in subsurface properties across the site, enabling the detection of anomalous individual elements, the diagnosis of their cause and the prediction of properties as construction proceeds over the site. All time-series data and KPIs are represented by standard classes of objects, leading to a generic coding of the data analysis; this minimizes the effort required to add additional sites and/or new KPIs. Examples are presented for a number of sites, where the system was used to identify anomalous columns.

May 1, 2022

By Jørn Thomsen, Christoffer Brodbaek

"As governments increasingly accord high priority to sustainable energy, policymakers are finding that wind energy has a long track record as a proven alternative to conventional energy supply.Over the past two decades, wind turbine projects have been constructed offshore because of more stable offshore wind conditions and because there is more available space for large wind farms out in the open sea. Vindeby Wind Farm in southern Denmark was constructed in 1991. As the world’s first offshore wind farm, it provided valuable information and experience for researchers and designers that have led to new technologies and design improvements, a trend that will continue as more offshore wind farms are constructed. Today, the world’s capacity of the installed offshore wind turbines exceeds 1,000 MW. Most of these are installed in Northern Europe where there was early political support and favorable conditions, such as strong winds and relatively shallow waters. Offshore wind projects are now under development around the globe, including continental Europe, the U.K. and North America. ‘The largest offshore wind farm today is Denmark’s Nysted Offshore Wind Farm, which has a total capacity of approximately 480,000 MWh, equivalent to the yearly consumption of 120,000 households. It is five to six miles offshore in the Baltic Sea in the southern part of Denmark.The owner is a joint venture between DONG Energy of Denmark and E.ON Sweden. Bonus Energy (now Siemens) supplied the wind turbines, and P. Aarsleff A/S and subcontractors supplied the foundations. The contractor’s consultant, COWI A/S of Denmark, developed and designed the turbine foundations. With a total capacity of 165.6 MW, the project consists of 72 Bonus 2.3 MW turbines in water depths up to 33 ft. The turbines have a hub height of 226 ft, and the turbine blade diameter is 270 ft. The rotor and nacelle (the structure that houses the generator, gearbox and other equipment) weigh approximately 150 tons, and the weight of the steel tower is approximately 130 tons. The wind farm site is located in a relatively protected area of the Baltic Sea, but during the winter months, the water often freezes and the foundations needed to be constructed to resist ice forces. The founding soils at the site are overconsolidated clay tills with boulders and with a thin layer of softer surface sediments. Pockets of up to 30 ft of soft sediments were encountered, which required special foundation preparations."

Jan 1, 2009

By Masahiko Yamaki, Takahiro Yamanashi, Hijiri Hashimoto, Hirochika Hayashi

"In this study, the authors used heat conduction analysis with the aim of quantitatively evaluating whether treating improved ground with cover soil is an effective measure for maintaining strength development in the surface layer of improved ground after constructing cement treated soil for the winter season. This report describes a simple procedure to evaluate covering soil thickness, which is necessary for the strength of the surface of cement treated soil, by using the freeze index and both the water content ratio and dry density.INTRODUCTIONIt was reported that when ground improvement using cement is performed in winter in a snowy cold region (Fig. 1 photo, Fig. 2), the uppermost 1 m of the improved ground (i.e., the cement-treated soil) tends to become prone to solidification failure from exposure to the cold air during curing (Hashimoto et al. 2006). In light of this, our research laboratory conducted unconfined compression tests using curing temperature as a parameter of analysis on improved ground toward understanding the influence of curing temperature (ambient air temperature) on the strength improvement afforded by ground improvement.The authors found that if the curing temperature is maintained at 0°C for the first 28 days after improvement and then at 5°C for the next 337 days after improvement, the improved ground is expected to have 90% of the unconfined compressive strength of improved ground whose temperature was maintained at 20°C for the first 365 days after improvement (Hashimoto et al. 2011)."

Jan 1, 2015

By Maurizio Siepi, Paul van Horn, John Coupland, Julian Crawley

"TTMJ is the acronym for the Slurry (Diaphragm) Wall Tension Track Milled Joint currently in development as part of the European Union's innovative and far-reaching Horizon 2020 initiative (FTI Pilot-2015-1 720579). The TTMJ Project has been specifically set up to deliver this versatile new step-forward in Slurry Wall technology. The TTMJ System is protected by patent in Europe and the USA, and is currently under development by a consortium comprising Trevi SpA (Italy), Arup (Netherlands) and CCMJ Systems (UK). The principles of the TTMJ System together with the installation process are herein described in general terms. The system is still under development with field trials scheduled for early 2018, so some of the detail will not be disclosed at this stage. It is the intention of the Authors that the results of these field trials and a more complete description of the System will be presented in a paper we intend to submit for the DFI/EFFC International Conference on Deep Foundations and Ground Improvement to be held in Rome, Italy in June 2018. The final section of this paper explains how the TTMJ system can be applied to a common application of slurry wall construction; deep circular or multi-cell shafts. The system can be used to construct shafts more easily and at less cost than current methods. It also allows shafts with smaller internal dimensions to be constructed than is currently practical.INTRODUCTIONCCMJ Systems (UK) realised that an innovative new approach to forming joints in both Slurry (Diaphragm) Walls and Secant Pile Walls would provide greatly improved joint integrity to greater depths, to the overallbenefit of retaining wall quality, across the world-wide foundations industry.In particular this new system is designed to:??Increase the effective depth range of Slurry Walls (especially walls excavated by grab) and Secant Walls??Remove the requirement for Stop-ends or Joint Formers??Allow for a Shear Key at the joint??Allow for a Water Stop to be installed at the joint??Permit Continuous Reinforcement across the joint??Optimise Reinforcement Density and hence Concrete Flow??Facilitate joints in corner panels eliminating the need for “L” shaped cages and reducing largesingle-pour concrete volumes and slurry storage capacity requirements.??Enable the construction of smaller-dimensioned square and circular deep shafts (especially useful for city-centre sites) than is possible with current methods.CCMJ Systems approached other industry specialists with a view to forming a development team to explore the possibilities for this new technique."

Jan 1, 2017

By Tara Schenk-McFarland, Mark Bliss

Echo Dam, located near Coalville, Utah, is a facility that provides storage for irrigation and municipal use. Original construction of the dam was completed in 1931. Because of seismic concerns, the spillway crest structure and upper chute section, founded on old landslide and colluvial material, were recently replaced. Prior to replacement of these structures, jet grouting of a block of the loose and potentially liquefiable soils, directly beneath the spillway crest structure was selected as the preferred alternative to address the potential for settlement and cracking of the spillway crest structure. The replacement or alteration of the in-place soil reduces the likelihood of seismic-induced excess pore pressure development and subsequent settlements. Core drilling and sample recovery of the production jet grouted columns was completed to verify compliance with the specifications. It was recognized that due to the larger rock sizes within the deposits that full homogeneity of the jet grouted zone was unlikely to be achievable. However, the purpose of this jet grouted section was to strengthen enough of the soil so that widespread liquefaction does not occur. During the jet grouting production many instances of ground fracturing occurred. Fracturing was evident based on grout/air bubbles exiting the surface near some of the grout holes during jet grouting, air bubbles appearing in the spoil pits, and lifting of the ground surface in the vicinity of the monitor during the jet grouting process while the system was pressurized. In one instance, a section of the upstream spillway slab, which was left in place, was cracked due to pressurized grout escaping beneath the slab. The overall results of the jet grouting were satisfactory despite difficulties encountered. The cause of the fracturing is hypothesized and a recommendation is included to reduce the likelihood of this occurring on future jobs.

Jan 1, 2017

By Joseph A. Sopko

The first documented procedures for designing frozen earth structures are over 50 years old, implemented long before the introduction of the Finite Element Method (FEM). Since that time, the development of three-dimensional models has made the traditional and often over-conservative methods relatively obsolete. This paper discusses a new approach that is largely dependent on the analysis of internal stresses with the frozen structure and comparison to frozen soil laboratory tests. A specific design process is discussed related to initial field investigation, laboratory testing, structural and thermal analysis, and performance monitoring. The design results are compared to case histories in the field that verify the procedure. BACKGROUND One of the first documented methods to designing frozen earth retaining structures was by Sangar (1968). Methodical refinements were published by (Harris 1995) and published by the International Symposium on Ground Freezing in 2002 (Andersland et al. 1991). The structural design or thickness of the frozen mass was based on the unconfined compressive strength of the frozen soils. Two simple equations for determining the thickness of a frozen shaft are shown in Fig. 1 and the first two equations below.

Jan 1, 2019

By Frank J. Purcell

“Down The Hole” (DTH) hammer drilling is often necessary to advance the casing during pile construction where the test bores have determined difficult drilling conditions with obstructions such as boulders, cobble and glacial till. The use of compressed air to operate DTH hammers in foundation drilling has been a contentious point in many regions of the world due to its potential to disturb the ground around the pile being constructed. There are many examples of damage to adjacent building foundations where compressed air exiting the pile being drilled disturbed the subsurface around the building’s existing piles. This paper looks at the use of compressed air in DTH hammer foundation drilling and the move towards controlling the exhausted air to avoid over drilling the pile, causing potential damage to nearby piles. Simulated models of air flow penetration into the soil of different configurations of drill bits are discussed to highlight design changes employed to better control the air during the drilling process. A case study of the construction of a water-tight pipe pile wall for a building’s underground parking structure is studied to demonstrate the potential of DTH hammer foundation drilling where the air is fully controlled.

Nov 1, 2022

By Thomas W. Scott, Manh N. Tran

Marine environments present a range of challenges for pile construction. This paper contains a discussion on the design and construction of marine piles for a recent Toll Shipping wharf upgrade in Burnie, Tasmania. The project involved several new structures including mooring, berthing and ramp dolphins supported by driven tubular piles with rock sockets, and an onshore mooring dolphin and ramp abutment supported by bored piles. Through the project, a range of construction challenges were experienced, including availability of tubular piles, the different penetration depths of driven piles into rock, the ability to drill out sockets when the piles were raked, the difficulty in verifying the design intent, latent conditions and ship impacts. The paper will present a summary of the different factors that influenced design concepts for the structures involved in the upgrade, and the challenges involved in the design of the structures. Following this, the paper will describe the methodology used to verify the design (including a pullout test), observations made during pile construction and lessons learned on how to limit risk throughout construction.

Nov 1, 2022

"TREVIICOS CorporationINTRODUCTIONThe Walter F. George lock and dam was constructed on the Chattahoochee River between 1955 and 1963 with the double function of improving navigation and generating power. Its 82 ft. by 450 ft. (25m x 137m) lock can accommodate large barge traffic and its four generating units with a plant capacity of 150 MW have an average energy output of 453,000 MWH. The dam consists of a 1,496 ft. (456m) long concrete structure housing the spillway, a non overflow portion, the power units and two earthen wing dams extending to the Georgia and Alabama sides, respectively 5,810 feet and 6,130 feet long (1770m and 1868m). As soon as the reservoir was impounded it became apparent that excessive seepage was occurring. From 1962 to 1985 a series of remedial works was performed using several techniques, but the problems continued under the dam, jeopardizing its generating potential and possibly undermining its stability.Finally, the decision was made to construct a deep cutoff primarily under the concrete portion of the dam to remedy the problem. PROCUREMENTOn July 5th, 2001 best and final offers were solicited by the Corps of Engineers (COE) for the construction of a deep cut-off to be built in front of the concrete portion of the dam from the bottom of the lake and tied into it. The cut-off had to cross an existing lock structure and an underwater retaining wall, as well as the remnants of a steel coffer cell left in place from the initial construction.The specifications required that the wall be built with a minimum thickness of 24” (600mm) and that it extended from the bottom of the lake to elevation -5 (1.52m) into the Providence formation, an impervious layer.While the land portions of the wall were on average 208 feet (63.4m) deep, the marine portion started from up to 90 feet (27m) of water and continued through different rock formations for another 100 feet (30m).Contractors were invited to propose their own method of constructing the cut-off and offers would be evaluated using several criteria, including technical, economical, organizational and experience.Three proposals were received and on August 14, 2001 an award was made to the Joint Venture (JV) of Treviicos and Rodio."

Jan 1, 2014

By Stuart Hardy, Xiangbo Qiu

The South Bank Place project comprised the redevelopment of the iconic Shell Corporation headquarters in Waterloo, located on the Southbank of the River Thames in central London. The site was originally developed in the 1950’s and due to the monitoring of the underlying Bakerloo Line tunnels by the Building Research Station it has become a seminal case history for the long term swelling behaviour of London Clay. The redevelopment, undertaken by a joint venture of Canary Wharf Group and Qatari Diar, included demolition of the existing building (with the exception of the main towers) retention of the existing basement structure and the construction of eight new mixed use buildings, up to 31 storeys in height. The foundations for the new buildings varied according to the building height and the below ground constraints. Two of the buildings are partially founded in reused under reamed piles that were installed as part of the original 1950’s development. The paper describes the novel methodology developed to assess the re-use of the under reamed piles which builds on the guidance published by CIRIA and the BRE for straight shafted piles. The paper also describes the physical investigations and numerical analyses undertaken as part of the assurance process and the procurement of latent defect insurance by the client.

May 1, 2022

By Athena C. Denivo, Pablo V. Lopez, Sissy Nikolaou, Alfred H. Brand, Ahmad Rahimian, Rudivien G. Josef

"The United States Tennis Association (USTA) Billie Jean King National Tennis Center (BJKNTC) site is located in the northeastern portion of the Flushing Meadows Corona Park area of Queens, N.Y. The site occupies some of the most difficult subsurface conditions for construction in the New York City (NYC) metropolitan area, with unique challenges from geotechnical, seismic and foundation design perspectives.At the USTA site, Paleozoic crystalline bedrock is found at a depth of roughly 300 to 400 ft (90 to 120 m) below grade. The geologic history of the site is complicated, starting from the early Pleistocene, when the ancient Hudson River temporarily changed course, flowing across Queens enroute to the Atlantic. It eventually carved a deep valley through the Cretaceous soils, in some places all the way down to bedrock. A series of glaciers advanced and retreated across the region during the Pleistocene times, filling the deep valley with layers of assorted glacial soils. At its southern edge, the last major glacier to flow across the region built up a ridge at the southern tip of Flushing Meadows known as the Harbor Hill terminal moraine. This ridge blocked the valley forming a dam, so as ice started melting away the valley filled up with a lake fed by glacial meltwater. Layers of clean outwash sand and varved silt and clay filled the glacial lake. The ice did not retreat in a steady manner, instead periodically readvancing over the previously deposited soil in the lake, then retreating far enough to let the lake drain temporarily into Long Island Sound, before readvancing again.As a result of this repeated sequence of retreat, advance, retreat, etc., there are places where a “crust” of desiccated soil formed when the lake drained, and areas with interlayers of outwash sand where ice readvanced into the lake. When the ice melted north of Long Island Sound, the glacial lake filling Flushing Meadows drained forming Flushing Creek. During the Holocene (roughly the last 11,000 years), as ice melted further away and sea-level rose, low lying areas filled with river sands and marine clays, along with coastal marsh deposits. Table 1 lists the soil design properties on site and Figure 1 exhibits the geologic section across the site."

Jan 1, 2015

By Sandeep Pattnaik

Spring stiffness of soil and rock at different depth is often required for a pile structural model. If the pile is rested in multiple layers of soil, then it is rather more complex to simulate the soil in a structural model. The spring stiffness will vary based on density of soil strata over the depth. When a pile is socketed in weathered rock followed by a soil layer, a sudden change in subgrade modulus can influence the pile deflection drastically. Determination of soil spring and simulation of the pile in this condition required correct interpretation of subgrade modulus. The conventional approach of pile spring calculation underestimates the spring stiffness by ignoring underlaying stiffer layers. A finite difference method (FDM) of analysis can reasonably estimate the p-y of soil / rock based on subgrade modulus of each layer. However, the transition between the layers can be better simulated as per the deflection pattern of the pile. The lateral deflection of the pile is mainly dependent on the stiffness of soil layer surrounded by the pile. Generally, the lateral influence of a pile varies from 4D to 6D depending on the soil type. Therefore, soil spring stiffness around the pile would require special attention of a Geotechnical engineer to avoid uncertainty in the prediction of pile behaviour. In this paper, emphasis has been given to develop an approach for pile spring stiffness design. A standard software program LPile has been used to develop p-y curves of soil and rock layers at different depths and then converted to soil/ rock springs over the depth. Modulus of Subgrade Reaction as given in IS 2911 (Part2) was also used to correlate the spring value for different type of soil. Obtained analytical results were compared with full scale field trial for lateral deflection of pile. A good agreement between these two approaches has been established. The effect of soil structure interaction in the structural model shall be simulated by assigning an equivalent vertical and horizontal soil spring, which is developed by Winkler’s soil spring approach. A simplified design principle for calculating the pile spring is discussed in this paper. This approach has been extensively used in Mumbai metro elevated line pile design.

Nov 1, 2022