Search Documents

By J. H. Hodgson

"Those of us who have been concerned with the problem of geophysical exploration in southwestern Ontario have followed the development of the Poulter method with much interest. I have much appreciated the opportunity of reading an advance copy of Dr. Poulter's clear exposition and of preparing the following brief remarks on the probable applicability of the method to the Palaeozoic area of southwestern Ontario.During the years 1944 to 1946, the Ontario Department of Mines, in co-operation with the Union Gas Company and the Dominion Natural Gas Company, operated an experimental party in the hope of establishing a seismic technique appropriate to the •area. The results were completely negative. During two summers' field work, no reflections whatever were obtained except in one area near Windsor. It is the •purpose of these remarks to inquire whether Dr. Poulter's techniques might yield favourable results.It was the conclusion of the report on our work that two principal causes contributed to the failure of the method. In the first place, the geological column possesses few elastic discontinuities and those that exist appear to have low reflection coefficients. In the second place, the area is drift-covered in general. This drift complicates the situation by absorbing seismic energy and by giving rise to groups of complicating refracted phases which obscure the entire interesting section of the record. The situation is further complicated by the high reflection velocities and the relative shortness of the Palaeozoic section, these factors combining to bring in a reflection from the basement in about half a second."

Jan 1, 1950

By J. N. De La Vergne, J. S. Redpath

"The authors make recommendations that they believe will improve the efficiency of a mining company's use of a mining contractor's services. The recommendations are in the form of specific ""DO"" or ""DO NOT"" instructions, giving explanations and covering the contracting process from the end of the feasibility study to the end of the job. IntroductionThis paper is an attempt by the authors to set out some of the things which they feel an owner should consider to achieve maximum effectiveness from mining contractors. It is based on our experience as contractors as well as our experience as consultants to owners. Should this paper create the impression that we feel all the responsibility lies with the owner, this is neither our intention nor our belief.Before the Tendering Process BeginsUse Defined EstimatesIn Feasibility Study DO NOT estimate your cost or schedule by telephoning contractors and asking them for ballpark figures. The only kind of estimate that is worth anything is the one that is clearly defined on paper and bears the signature of the author. This type of time or cost estimate takes time to prepare. In general, the estimate will be worth what you pay for it.Ensure Adequate FinancingDO NOT ask contractors to tender on a project unless the funds have been approved for it. Remember that, depending on the size of the job, it will cost the contractor from $5,000 to $50,000 to prepare his tender. When financing is not assured, a single contractor should be approached regarding a detailed estimate and he should be paid for it. Contractors should not be expected to finance speculative mining ventures."

Jan 1, 1980

By T. A. Postolski, A. J. Sinclair

"Abstract - Where block (selective mining unit) grade distributions can be determined, the effect of average random errors of block grade estimates on metal recovery can be evaluated quantitatively. That is, for a given estimation error and cutoff grade, it is possible to calculate the quantity of metal that is lost as a result of misclassifying ore blocks as waste, as well as the dilution that ensues from misclassifying waste blocks as ore. Example calculations using a computer program GAINLOSS and realistic block grade distribution parameters for both a porphyry-type deposit and an epithermal gold deposit illustrate some fundamental relations that are important in quality control of estimation and in reconciliations concerning a comparison of ore estimates with production.Where the cutoff grade is on the lower tail of the grade distribution, metal arising from dilution can be much less than metal lost through misclassifying ore as waste. Hence, average grade of milled material could possibly be higher than expected (estimated) and tonnes milled will be smaller than estimated.Where the cutoff grade is on the higher tail of the grade distribution, tonnes arising from dilution will be greater than tonnes lost by misclassifying ore as waste. Thus, tonnage mined will be greater than estimated and the average grade milled will be less than estimated.The software GAINLOSS permits rapid comparison of the tonnes and average grade for all blocks selected as ore for a variety of levels of block estimation errors. These comparisons can be incorporated in a financial analysis to evaluate whether or not it is worthwhile to improve a high, average block estimation error to some lower value."

Jan 1, 1998

By W. Lamb

Feed Preparation ? Five primary parameters affect the screening efficiency ? Ore characteristics ? Operational characteristics ? Screen characteristics ? Water addition and washing ? System design

Apr 1, 2005

By Patrick Chabot

Ce document présente une méthode hybride de long trou favorisant une méthode de minage initiale par chambre-magasin et complétée par une méthode de minage long trou. Cette méthode a été adaptée suite à plusieurs facteurs tels qu?une géologie complexe, une rareté de mineur d?expérience et un haut taux de roulement de main d?oeuvre spécialisée. Cette méthode a permis d'excellents résultats par rapport à la dilution. De plus, la récupération de pilier à haute teneur par forage long trou sera expliquée. Cette méthode permet aussi de récupérer le minerai qui est resté accroché dans les chantiers chambre-magasins. Introduction : La mine Géant Dormant est une mine filonienne d?or située à environ 80km au nord de la ville d?Amos au Québec. Elle est en opération depuis 1988 et à la fin de 2007, elle a produit près de 885 000 onces d?or à partir d?environ 2 400 000 tonnes de minerai pour une teneur moyenne d?environ 11,5g /t Au. Cette mine est la propriété d?IAMGOLD Corporation depuis l?acquisition de Cambior par cette dernière au mois de novembre 2006. Elle emploie 151 employés permanents et environ 41 entrepreneurs.

Feb 1, 2008

By Lawrence Devon Smith

"The Management and Economics Society has undertaken a survey of industry practice in the evaluation of mineral projects. The survey addresses a number of issues relating to evaluation techniques, discounted cash flow methodology, and risk. Completed during the spring and summer of2005, the results provide a record of opinion at an active and vital time in our industry.The 2005 survey questionnaire was distributed by e-mail to groups and organizations around the world. There were 22 respondents out of several hundred questionnaires distributed (we gather this small proportion of respondents is typical for such surveys). The responses, although a small number, show a consistency that suggests that the survey has captured the views of the industry. The results of the survey are summarized below in series of tables and graphs.The reader is cautioned that the results are a snapshot of industry practice at a point in time as represented by a small sampling of the industry's practitioners. These results should be viewed as indicative values."

Jan 1, 2003

By G Anders

The effectiveness of two types of powder used in long-wall slashing was compared. The evaluation of the results can serve as a good example of how the application of statistical methods to underground test data can help to minimize the number of tests to be carried out. The conclusions are stated concisely, including a definite assessment of the reliability of the tests. Introduction AN assignment at the Algom Nordic mine called for a performance comparison between 70 per cent Cilgel B and 75 per cent Dygel in longwall stope slashing, particularly taking into account, in both cases, the build-up of bootlegs as dependent on hole deviation. Stopes were usually 8 to 10 ft. high and inclined at about 17 degrees. Starting from a raise, they were widened by consecutive longwall slashes to 60 ft., and, al-lowing for drift pillars, were approximately 300 ft. in length along the incline.

Jan 1, 1964

Presentation Overview ?? Project Setting ? Project Context ? Challenges ?? Managing Commitments ?? Project Update ?? Maximizing Aboriginal Economic Participation in Resource Development PROJECT SETTING ?? Developed on the traditional lands of the Labrador Inuit, and the Labrador Innu ?? Courts have held that Aboriginal peoples in Canada possess special rights to traditional lands ?? Rights can include requiring resource developers to enter into Impacts and Benefits Agreements ?? Development agreement with Newfoundland and Labrador was required

May 1, 2004

By B. S. Riess

A novel design for an automated uranium pellet stacking system is presented. This system is designed as a drop-in solution to the current production line to enhance the fuel pellet stacking process. The three main goals of this system are to reduce worker exposure to radiation to as low as reasonable achievable (ALARA), improve product quality, and increase productivity. The proposed system will reduce the potential for human error. This single automated system will replace the two existing pellet stacking stations while increasing the total output, eliminating pellet stacking as a bottleneck in the fuel bundle assembly process.

Aug 1, 2010

By Richard P. Taylor, Rod Henham

Abstract - Newly discovered pegmatites distributed throughout the sub-surface environs of the Musselwhite Archean gold deposit occur as narrow dikes that intrude most of the major lithological units. The mineralogy and textures of the pegmatite dikes are characteristic of granitic pegmatites of the "Rare-Element Class"; more specifically, they closely resemble varieties of the "Complex-type" granitic pegmatites that are commonly associated with zones of tantalum mineralization. The essential minerals in the dikes comprise albite, quartz, and K-feldspar, together with lesser amounts of mica (including lepidolite), spessartine, tourmaline, and locally, spodumene. Fine-grained (30 µm to 300 µm), tantalum-bearing minerals occur in the quartzo-feldspathic matrix of the dikes as disseminations, in interstices, and in small vugs. The nature of the tantalum-bearing mineral assemblage present in individual pegmatite dikes varies from a simple mineral assemblage composed of ferrocolumbite (with around 39 wt% Ta2O5) in the most northerly dike, to more complex assemblages comprised of manganotantalite (with up to 75 wt% Ta2O5), ferrotapiolite (with up to 79 wt% Ta2O5), and microlite (with up to 76 wt% Ta2O5) that are present in dikes located several kilometers to the south and southwest. The compositional characteristics and textural relationships of the tantalum-bearing minerals in the dikes provide evidence of igneous fractionation trends that are typical of rare-element granitic pegmatites. Such trends suggest that the newly discovered pegmatites represent part of a more extensive group of cogenetic, tantalum-mineralized dikes.

Jan 1, 2001

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By A. Innus, R. Pelletier, C. Allaire

Refractory used for molten aluminium confinement is typically assessed separately for thermo-physical properties and molten aluminium resistance. This present work provides a case study comparison of four commercial refractory products that were subjected to a test procedure that combines mechanical impact, thermal shock with molten aluminium contact. The main conclusion of this work is that physical and mechanical property values by themselves do not, and cannot, predict the response of refractory to potential interactions between molten aluminium contact and thermal shock and mechanical impact. Adequate physical simulation is imperative to quantify the effect of such interactions.

Jan 1, 2004

By Masakazu Daté

Moisture effect has been studied for the CO oxidation over Au/TiO2, Au/Al2O3 and Au/SiO2, in the range of H2O concentration over four orders of magnitude. It has been found that the catalytic activity is generally enhanced by moisture in the reactant gas. The enhancement is as large as two orders of magnitude. Response to the moisture concentration, however, depends on the support oxide, indicating different contributions of the support to the reaction steps. The moisture effect is reversible and the activity is mainly determined by the amount of moisture absorbed by the catalyst. The apparent activation energies are not significantly influenced by moisture for Au/TiO2 and Au/Al2O3. On the contrary, non-uniform conversion curves versus temperature observed for Au/SiO2 are drastically changed, which indicates that the reaction over Au/SiO2 does not take place at low temperatures without moisture. The moisture effect may be probably attributed to the decomposition of carbonate species accumulated during the reaction, while the ?OH group might directly participate in the reaction pathways as a promoter.

Oct 1, 2003

By Emmanuel Henry

The Kiruna Mine, operated by Luossavaara-Kiirunavaara AB (LKAB), is a large-scale sublevel caving operation located in Arctic Sweden. Iron ore is extracted at a rate of 60 000 tpd from a four-kilometre long, 80-100 m thick and 60-degree dipping orebody. Actual production depth is 800 m under the top of the footwall and about 550 m under the average regional ground level. Because no support is left between the footwall and the hanging wall and despite the relatively low mining depth, extraction results in the formation of a huge stress shield modifying the original stress field and concentrating it just beneath the mining level. Effects of stress concentration on the rock mass are monitored through field observations and a seismic system. Severe stress-induced deterioration of openings is visible to a certain radial distance from the mining level: pillar crushing and fault slips are more and more common and extended. The seismic system, installed in collaboration with CANMET, confirms the field observations and completes them in the rock mass: fault slips and major seismic events are recorded. The system proves its effectiveness to outline the extension of the dynamic response of the rock mass, which actually seems much larger than field observations let think.

May 1, 2001

By Xiaolin Cheng, A. J. Sinclair

"Norm calculation procedures originally designed principally for igneous rocks are very rigid in their application and, in general, do not utilize important alteration minerals. For instance, volatile components are essential constituents of many metasomatic rocks but either are not used or are not used effectively in determining normative minerals by the CIPW norm or Niggli-Barth norm procedures. Our approach to determining norms for metasomatic rocks allots all major, minor and volatile constituents to a set of standard normative minerals which are commonly observed as products of hydrothermal alteration. A useful procedure is to have a metasomatic norm approximate the mode as closely as possible. Petrographic information helps to provide the necessary mineralogical constraints. With the recognition of an immobile component and knowledge of sampling and analytical errors in lithogeo chemical data, it is possible to recast norms into amounts of alteration minerals relative to a given amount (100 grams) of parent rock. Combining these results with the calculations of absolute loss or gain of individual chemical constituents and considering errors (e) for an appropriate confidence level, an overall (net) material exchange equation can be presented as follows:<equation>where all items have extensive units (e.g., grams). The model includes the initial and final mineralogy of rocks (evident in the field) as well as gains and losses of specific elements. Only those constituents whose calculated losses and gains are significantly different from zero are retained in the above model, and only the normative minerals with abundances significantly different from zero are included in the model (equation). One advantage of the chemico-mineralogic model is that parent rock and product are modeled in mineralogical terms that are familiar to and easily usable by exploration geologists."

Jan 1, 1995

By Xiaolin Cheng, A. J. Sinclair

"Abstract - Norm calculation procedures originally designed principally for igneous rocks are very rigid in their application and, in general, do not utilize important alteration minerals. For instance, volatile components are essential constituents of many metasomatic rocks but either are not used or are not used effectively in determining normative minerals by the CIPW norm or Niggli-Barth norm procedures. Our approach to determining norms for metasomatic rocks allots all major, minor and volatile constituents to a set of standard normative minerals which are commonly observed as products of hydrothermal alteration. A useful procedure is to have a metasomatic norm approximate the mode as closely as possible. Petrographic information helps to provide the necessary mineralogical constraints. With the recognition of an immobile component and knowledge of sampling and analytical errors in lithogeochemical data, it is possible to recast norms into amounts of alteration minerals relative to a given amount (100 grams) of parent rock. Combining these results with the calculations of absolute loss or gain of individual chemical constituents and considering errors (e) for an appropriate confidence level, an overall (net) material exchange equation can be presented as follows:SMineralparent rock ± e + SConstituentgained from solution ± e= SMineralaltered rock ± e + SConstituentlost from wall-rock ± ewhere all items have extensive units (e.g., grams). The model includes the initial and final mineralogy of rocks (evident in the field) as well as gains and losses of specific elements. Only those constituents whose calculated losses and gains are significantly different from zero are retained in the above model, and only the normative minerals with abundances significantly different from zero are included in the model (equation). One advantage of the chemicomineralogic model is that parent rock and product are modeled in mineralogical terms that are familiar to and easily usable by exploration geologists."

Jan 1, 1995

By David Fisk

Mining: Current Business Environment ? Commodity prices are high, but cyclic ? Increasing global competition ? Equipment costs remain high ? Maintenance costs continue to increase ? Aging experts with ?tribal knowledge? are leaving/retiring ? High metal prices multiplies theimpact of downtime on production and profitability

May 1, 2008

IBI Alliances ? Government ? People ? Academic ? Associations ? Media ? Customers ? Agencies ? Shareholders ? Industry consultants ? Investment Authority ? Geological Survey ? Department of Mines ? People ? Local Residents ? Mineworkers ? Academic ? University of Guelph ? Uganda Vermiculite Institute ? Associations ? TVA ? Organic Certification ? Media ? Canada ? International ? Customers ? Advocacy role ? Agencies ? Regional International

May 1, 2006

By A Smirnov

The problem of thin and very thin coal seam extraction is examined in a long perspective of Ukraine?s fuel and energy industry development. The technical and economic benefits of the coal seam selective mining technique are described, including beneficial environmental impact.

Aug 1, 2013

By N. Giguère

Until recently, the heat treatment of pressure die cast parts has always been considered unpractical because the solution heat treatment resulted in unacceptable blistered parts. This was due to the presence of massive porosity associated with the die casting process where the inflow of metal inside the mold cavity is extremely turbulent. With the steady improvement of foundry practices and the generalization of vacuum die casting, porosity defects have been reduced to the point that a partial solutionizing heat treatment can be applied without any damage to the casting. However the solutionizing temperature must be lower than that applied to macroporosity free castings and for much shorter time. The object of the present study was to determine the optimum solutionizing temperature that can be applied to aluminum 383 die cast brackets along with the optimal temperature and time of aging resulting in the highest improvement in mechanical properties (both strength and ductility). This was done by testing strength and deformation on the casting itself using a specially designed jig; the crushing force to deformation curve was analyzed so as to quantify the improvement in both strength and ductility gained with the partial precipitation hardening heat treatment.

Jan 1, 2011