Search Documents

By B. R. Casement

"Managing safety on the basis of after-the-fact reaction to accidents, can never be more than partially successful. Injuries will occur as long as the underlying potential for them still exists. Unless unsafe actions and conditions are systematically decreased, no program can have more than a short-term success.The pro-active Bullmoose loss control process, instead, focusses on heightening awareness of work habits, to prevent incidents by reducing their potential.Any safety program will be doomed to failure if the development of safe work habits depends on the safety supervisor or a safety committee. At Bullmoose the focus is on the critical actions out of which losses emerge. The successful application of performance-related feedback is achieved by taking safety, health, and environmental concerns into consideration on every level, and, by doing the right thing in every job done.What is an Exceptional Loss Control Program?If an accident in an organization creates a flurry of interest, resulting in ""cracking down"" on violations for a short period of time then an ""exceptional"" loss control program exists. Unfortunately, exceptional here does not refer to the effectiveness of quality of the program but to the fact that the organization is managing loss control by exception. The degree of management attention in an ""exceptional"" safety program varies over a period of time, remaining low as long as the rate of losses stays within management's acceptable control limit (Fig. I). When the losses rise above this, management becomes motivated to begin ""exceptional"" efforts to manage losses. When the rate falls again to within the accepted limit, efforts to control losses take a back seat.Such a strategy guarantees that losses will be tolerated or ignored as long as the actual rate is below the acceptable limit. Simply to lower the limit would not reduce losses, but would result in an increased number of flurries of management attention to loss control. This ""on-again, off-again"" style of management teaches supervisors and others that basic loss control is not as important as are statistics."

Jan 1, 1993

Presentation Overview ?WRDC Purpose and Activities ?Women in Trades, Technology and Operations (TTO) Occupations ?Factors in Successful Recruitment / Retention of women (VBNC) ?Recruitment and Retention Strategies ?Conclusion Women in Resource Development Committee (WRDC) ?Incorporated in 1999 as a Not for Profit Organization ?Based in Newfoundland and Labrador ?Works to Increase the Participation of Women in Natural Resource Industries ?Research (Using Gender-Based Analysis) ?Career Exploration Programs for Women and Girls ?Outreach and Advocacy ?Policy Development ?Public Awareness and Education ?Gender Sensitivity Training ?WRDC Educational Resource Centre

May 1, 2006

"The North Star and Don Jon copper deposits lie beneath the waters of Thompson Lake, which is 12 miles east of Flin Flon, Manitoba. The deposits were discovered during the years 1949 and 1951 by diamond drilling done in the vicinity of pyritic showings on the shores of two small islands in the lake. The Don Jon ore body lies 1, 700 feet southeast of the North Star orebody and is connected with the North Star mine workings by a crosscut on the 600-foot level (Figure 1 ).Production began on January 1, 1955, at a combined rate of 200 tons per day. The ore is trucked, on 24 miles of highway, to the Hudson Bay Mining and Smelting Co., Limited mill at Flin Flon.Regional GeologyRocks in the Thompson Lake area are Precambrian volcanics, ranging in composition from andesite to rhyolite, with related tuffs and breccia. These rocks have a general north-south trend and are steeply dipping. The area is part of the Lac Aimee fault block, which probably is the southward extension of a south-plunging syncline now thrust some miles to the north. This regional deformation has produced many subsidiary zones of intense shearing and crumpling. It is in two of these zones of shearing and drag-folding that the orebodies occur. The only recognizable intrusive is a narrow diorite sill which trends northeasterly near the west shore of Thompson Lake.The North Star MineA pyritic showing, carrying some chalcopyrite, was discovered around the year 1930 on the west side of a small island near the west shore of Thompson Lake. This ground was included in a group of claims acquired by the Hudson Bay Exploration and Development Co., Limited in 1947.In the years 1949 to 1951, a diamond drilling program outlined a copper sulphide orebody. This ore zone comes to surface beneath the lake, about 300 feet north of the pyritic showing on the island."

Jan 1, 1949

By A. Singh

"The flotation of fine minerals less than 10 µm in size is an age old challenge spanning both the precious metal and industrial mineral sectors across a range of commodities. This problem has been brought into sharper focus by the emergence of the practice of fine grinding of flotation feed to effect better liberation of the targeted minerals. However, the ability of conventional flotation cells to effectively float the liberated fines remains questionable. In order to overcome this problem, Gold Ore postulates the “Bringing the Mountain to Mohamed” hypothesis which comprises the steps of gas nucleation on particle surfaces, aggregation of particles and levitation of aggregates. Testing of this hypothesis at Mintek, South Africa, showed a ~180% increase in the Kelsall kfast factor coupled with a projected recovery improvement of ~4 % for the Mach Reactor case coupled with a final concentrate grade of ~2 times that of conventional flotation. These fundamentals were then extrapolated to plant scale with Mach Reactors installed on the flotation feed at Platmin’s Tailings Scavenger Plant (TSP) with the objective of scavenging the fine minerals lost to tailings by the main plant. This paper details the theory, pilot plant results as well as key aspects of the full scale plant design supplemented by operational plant observations after commissioning. This game changing application is regarded as being pivotal to future flotation plant design whilst providing the technology leverage required for the survival of mineral operations in an economically unfriendly environment.INTRODUCTION - THE CONUNDRUM OF FINE PARTICLE FLOTATION“If the mountain won't come to Mohamed then Mohamed must go to the mountain” is an age old saying written into the book of proverbs in 1670. Legend has it that Mohamed promised his people that he would summon a mountain to come over to him so that he could offer up his prayers from its summit. After numerous attempts at moving the mountain went in vain, Mohamed, quite unabashed, said “Well if the mountain will not come to Mohamed, then Mohamed will go to the Mountain.” In this analogy, Mohamed is a fine particle <10 µm and the mountain is a bubble within a flotation system. The age old challenge is how to bring these two together to achieve attachment?"

Jan 1, 2016

By R. W. Thompkins

The two largest contributors to silicosis in machine men are dust from drilling and dust from blasting. With the advent of the shatter-cut method of blasting, the evils of blasting dust were greatly reduced. The problem of dust from drilling has been attacked from two different angles: (1) The adoption of dustless frontheads or enlarged water tubes, both of which have proved capable of reducing dust concentrations; and (2) The adoption of better ventilation. Many operators are loath to adopt dustless frontheads or enlarged water tubes on Leyner drills because of the increased repair costs on drills, and also because it has been found difficult to enforce &apos;the proper usage of dustless machines: for example, workmen sometimes plug the vents in the fronthead.

Jan 1, 1943

By M. S. Moats

"The effects of commercial copper electrorefining additives (glue and thiourea) on the electrochemical removal of bismuth are of importance in copper production. It was found that Bi(III) electrodeposition occurs readily from acidic sulfate solution via a diffusion-controlled quasi-reversible reduction. The diffusion coefficient of Bi(III) was measured and found to be less than reported values of copper in similar solutions. The presence of thiourea and/or glue was found to accelerate or de-polarize Bi(III) reduction on stainless steel as compared to the inhibition or polarization of Cu(II) reduction. The additives also inhibited the dissolution of the Bi-Cu co-deposit during cyclic voltammetry. During short term deposition studies, the additives increased the concentration of Bi in co-deposited Cu-Bi products from solutions with low concentrations of Cu (<2 g/L). Bi deposition was significantly suppressed by increasing the Cu(II) concentration in the solution. The formation of a copper layer on the stainless steel electrode appeared to significantly suppress the reduction of Bi(III). This study demonstrates that glue and thiourea depolarize the deposition of bismuth on stainless steel. Therefore, the additives could be used to improve Bi impurity removal during third stage liberation.INTRODUCTIONThe production of high purity copper has been steadily increasing due to the wide application of the metal and its alloys in electrical and electronic products, infrastructure construction, industrial machinery and equipment, general products and transportation (Moskalyk et al., 2003). Most high purity copper is manufactured from copper sulfide mineral concentrates and/or scrap via a pyrometallurgical process followed by electrorefining (Navarro et al., 1999). During the electrorefining process, cast anodes of 99-99.5% purity are electrochemically dissolved into an acidified copper sulfate solution while high purity copper (>99.99%) is plated on stainless steel blanks or copper starter sheets (Davenport et al., 2002). The control of cathode deposit growth (purity and morphology) while maintaining a high current efficiency is of significant importance for copper refining (Ilkhchi et al., 2007). At typically applied current densities for industrial copper electrorefining, mass and charge transfer play important roles in the quality of cathodic products (Hiskey et al., 1998). If the real current density at some surface points is substantially higher owing to uneven current distribution, then rough spots can and will grow faster leading to nodules (Suarez et al., 1992). Nodulated deposits tend to capture solution and anode impurities (slimes) resulting in unacceptable cathode quality (Afifi et al., 1987). Furthermore, these nodules can grow until they eventually contact the anode leading to short circuits and current efficiency reduction (Ilkhchi et al. 2007)."

Jan 1, 2016

By K. M. Sarkar

"In many plant trial s(1,2) it has been proven that very small amounts (10 to 20 ppm) of uranium dissolved in mine water can be effectively recovered by the use of ion exchange resins and this uranium recovery has many advantages. In this paper an economic analysis at different levels of uranium contamination and at different market prices of uranium are described.For this study an operating mine-mill complex with a sulphuric acid leach circuit, followed by solvent extraction (SX) process, is considered, where contaminated mine water is available in excess of process requirements. lt is further assumed that the sulphuric acid eluant containing uranium would be mixed with the mill pregnant liquor stream that proceeds to the SX plant for final uranium recovery.Recovery by Ion ExchangeMine water, in this study, is defined as the water coming from the underground mine, or mine pits, and the run-off water from stockpiles, mine shops, crushing plant , washdown areas, etc.In nature, uranium mainly occurs in two stages; reduced (tetravalent) and oxidized (hexavalent) . The oxidation of sulphides present in the orebody often causes the presence of S04- and acidity in mine water, and this acidic water readily dissolves U+6 part of the depo sit. The react ion between hexavalent uranium, which is dissolved in water as U02+ 2 cation and S04 producing uranyl sulph ate as,"

Jan 1, 1984

By Carlos Palacios M., Brian K. Townley

"Abstract - The mainland Aysén region of Chilean Patagonia (44°15&apos; - 47°30&apos;S) is a representative segment of the South American active continental margin, distinct with respect to northern and central Chile. Mineralization consists mainly of polymetallic deposits, with important Zn-Pb mines and more recently discovered Au-Ag deposits, unlike the central Andes, which are dominated by Cu mineralization. On a regional scale, rocks may be grouped in four main map units: 1) the Paleozoic metamorphic basement; 2) upper Jurassic-Cretaceous calc-alkaline volcanic and marine sedimentary rocks; 3) the Patagonian batholith, and 4) upper Cretaceous to Miocene basalts and marine and continental sedimentary rocks. The upper Jurassic-Cretaceous rocks and the Patagonian batholith formed in a volcanic arc and back-arc setting superimposed on the Paleozoic metamorphic basement.Based on geographic location and geologic and tectonic setting, ore deposits in this region are assigned to three groups, from south to north: El Faldeo, Fachinal, and El Toqui. The El Faldeo group (south of 47°05&apos;S) includes upper Jurassic Zn-Pb skarn and associated polymetallic massive sulfide vein deposits locally overprinted by Au-rich epithermal mineralization, hosted by volcanic and sedimentary rocks and/or by rocks of the metamorphic basement. The Fachinal group (46°05&apos; - 47°05&apos;S) consists of volcanic-hosted lower Cretaceous Au-Ag epithermal deposits, except for the Mina Silva and Manto Rosillo deposits, which are metamorphic basement-hosted Zn-Pb skarns. The El Toqui group (44°30&apos; - 46°05&apos;S) comprises lower Cretaceous Au-rich Zn-Pb skarns and associated polymetallic veins, as well as Au-Ag-rich epithermal deposits, hosted by volcanic, intrusive, and marine sedimentary rocks. Galena lead isotopic signatures for each deposit group indicate a decreasingly radiogenic trend from south to north, suggesting different lead sources or differences among underlying crust. Three metallogenic provinces and two metallogenic epochs are proposed for the Aysén region: the El Faldeo metallogenic province of Late Jurassic age; and the Fachinal and El Toqui provinces of Early Cretaceous age. Résumé - La partie continentale de la région d’Aysen (Patagonie chilienne, 44°15&apos; - 47°30&apos;S), est unsegment représentatif de la marge continentale active d’Amérique du sud, différent des segments du nordet du centre du Chili. La minéralisation, qui consiste essentiellement en des dépôts polymétalliques, avec d’importantes mines de Pb-Zn, et des dépôts d’Au-Ag récemment découverts, différe de celle des Andes centrales où domine la minéralisation cuprifère. A l’échelle régionale, les roches peuvent être regroupées en quatre unités cartographiques principales : 1) le socle métamorphique paléozoïque, 2) les roches volcaniques calco-alcalines et les sédiments marins du Jurassique supérieur-Crétacé, 3) le batholite patagonien, et 4) les sédiments marins et continentaux ainsi que les basaltes du Crétacé supérieur-Miocène. Les roches du Jurassique supérieur-Crétacé et le batholite patagonien, formés dans un contexte d’arc volcanique et d’arrière-arc se superposent au socle métamorphique paléozoïque.Fondé sur la localisation géographique ainsi que sur le cadre tectonique et géologique, les dépôts de minerais de cette région se répartissent en trois groupes, du sud au nord, El Faldeo, Fachinal et El Toqui. Le Groupe El Faldeo (sud de 47°05&apos;S) contient des skarns à Pb-Zn du Jurassique supérieur associés à des veines de sulfures massifs polymétalliques, localement recoupées par des minéralisations épithermales, riches en Au, et contenus dans des roches sédimentaires et volcaniques et/ou dans des roches du socle métamorphique. Le Groupe Fachinal (46°05&apos; - 47°05&apos;S) consiste en des dépôts épithermaux Au-Ag, se trouvant dans des roches volcaniques du Crétacé inférieur, excepté pour les dépôts de la Mine Silva et Manto Rosillo, où des skarns à Pb-Zn, se trouvent dans le socle métamorphique. Le Groupe El"

Jan 1, 1999

By David Minson

On many occasions, operators have seen that high density and paste thickener performance does not meet the initial design expectations, and the installed equipment produces lower than expected thickener underflow solids content. This lower-density tailings slurry leads to more water and lower beaching angles being seen at the tailings storage facility (TSF). This not only reduces storage capacity, but also increases the risks of non-compliance with environmental permit constraints. Reasons for the shortfall in performance can be many, but perhaps the main problem is inadequate understanding of the critical components of thickener design and operation, with too much reliance placed on standardised design terminology; such as tph/m2. This paper discusses additional factors that influence high-density thickener operation and presents test work that defines “Dynamic Slurry Fluidity”, “Bed Compaction Rates”, and “Natural Slump Angles” for these high yield stress/viscosity slurries. Finally, the paper uses this data to define thickener geometry, drive torque, floor slope(s), rake blade configuration and how this can be used to provide engineers with more tools for in depth evaluation of a High-Density thickener design. INTRODUCTION Generally copper mines are high tonnage operations, with copper flotation concentrators producing high volumes of tailings slurries of milled solids and water. As a result, Tailings Storage Facilities (TSF) become very large and this, along with potential scarcity of water, favours a design that maximises storage space. In theory, the use of filtration equipment that achieves immediate water recovery, high TSF in-situ densities and high stacking angles are preferred for this duty. However, large tailings filter units are uncommon, and have high operating and capital costs that favour the use of thickeners. The use of high-density thickeners to produce a thick or near-paste like slurry with high un- sheared yield stress values above 100 Pascals, is becoming more common. The higher thickener underflow is required to not only maximise water recirculation within the mill, but to also increase beaching angles, maximise tailings storage capacity and minimise evaporation losses arising from large areas of superficial water. However, the reliability of this equipment is also under scrutiny and there is perhaps a need to better define these designs.

Jan 1, 2019

By J. X. Guo, A. Pindred, J. Moore

"Two modified centrifugal flotation cells (CFC), Q2 and Q3 models, have been developed for froth flotation. The operating mechanism of Q2 uses a rotating bowl to create a centrifugal force on the feeding slurry. Froth concentrate is collected on the central top of the cell and tailing is discharged along the top edge of the rotating bowl. The Q3 utilizes a vertical rotating feed pipe to introduce the feed slurry into a stationary flotation column cell. A centrifugal force is also created by a rotating pipe for the feeding slurry. Froth concentrate floats over the cell and tailing discharges through the bottom of the cell. The centrifugal force causes the flotation recovery of fine particles from CFC to be higher than from the conventional cell. The major operating variables of CFC are the rotating speed, air flow rate into feed slurry, and slurry feeding rate etc. Flotation tests have been carried out on synthetic mixtures of galena-silica and chalcopyrite-silica, as well as some natural base metal ore samples. Parallel tests were also conducted on a conventional flotation cell. The comparative test results demonstrated that both Q2 and Q3 have the advantage of higher recovery of finer than 10 µm mineral particles, which are very difficult for the conventional non-centrifugal flotation cell to recover. The grade-recovery curves produced from CFC are equivalent to or better than the conventional flotation cell. There is a potential in the future for the CFC to be employed in slime flotation.1. IntroductionA centrifugal flotation cell (CFC) was originally developed by Clean Earth Technologies [I] to separate oil from water and was subsequently applied in froth flotation. Figure 1 illustrates the design of the original CFC, in which a vertical feeding pipe is attached to the center part of a rotating drum and a stationary shell encloses it to direct the float froth and tailing discharge. The slurry flows down to the bottom of the spinning drum, gets in touch with a screen of air bubbles and then migrates outwards under the effect of centrifugal force. After the mineralized froth enters the rotating cell, it is pushed back to the inner surface. The overflowing froth is collected in the froth launder while the tailing slurry is discharged through orifices along the outer rim of the drum."

Jan 1, 1998

By D. G. Cerigo

"INTRODUCTIONAn interim report covering an uncompleted project on revenue mill optimization was presented at the invitation of Mr. C.S. Stevens, the Secretary of the Canadian Gold Metallurgists. The work described summarizes the preliminary work carried out at the Noranda Research Centre on computer mill optimization and is an attempt to arrive at a model of a circuit using the ""black box"" approach and hence by using economic factors related to concentrate dollar value to maximize revenue. The help and cooperation of Mr. J.D. Wild, Mr. M.J.S. Bennett of Noranda and Dr. A. Bobkowicz of McGill University is gratefully acknowledged.DERIVATION OF MODELHistorical data from the Normetal mill were used for the study. Normetal ore contains chalcopyrite, sphalerite, gold, silver, pyrite and pyrrhotite. For simplicity, data were chosen for days when only two concentrates had been derived, a copper concentrate which also contains the gold and silver, and a zinc concentrate. In these periods when pyrite concentrate was not produced, its circuit was used as an extra zinc scavenger unit. Figure I is a schematic drawing of the circuit and Table I explains the nomenclature.The mill had been operated to obtain a fixed grade of copper and zinc in the copper and zinc concentrates respectively, at the same time insuring acceptable recovery levels. The target grade for the copper and zinc concentrates had been derived by manual calculations based on past experience. The data used were 170 sets of daily mill reports, a sample of which is shown in Table II. The data consist of daily tonnages of feed, concentrates and tailings and their average compositions obtained by taking samples every twenty minutes from each stream and analyzing the daily composite samples."

Jan 1, 1967

By T. T. Perles

This paper will review the state of the global vanadium industry and outline the implications for the market in the coming years. Global vanadium resources and reserves will be defined. Current production of vanadium will be quantified and examined in terms of production by country, sources of raw materials for production and cost implications of the production processes. Current consumption of vanadium by country and by application will be reviewed. Vanadium supply/demand balance in recent years and the resulting impact on global inventory levels will be discussed. Projections for changes in global production, consumption and resulting inventory changes for the vanadium market in the coming years will be made.

Jan 1, 2014

By V. Itkin

"Three methods were tested for the beneficiation of aluminum scrap, generated by heavy medium separation of non-ferrous automobile scrap residue. These were: crushing in a shredder followed by screening; grinding in a ball miff followed by screening; and eddy current separation. The best results were obtained with the grinding-screening method. IntroductionThe usual method of aluminum alloy reclamation from non-ferrous automobile scrap residue consists of a two-step heavy medium separation to remove materials lighter than and heavier than aluminum. The resulting aluminum scrap still contains over 15% impurities such as stones and glass, heavy rubber, insulated copper wire , plastics and heavy metals entrapped by macerated aluminum piece s, composite fragments, etc.(2). Upon melting, these impurities create difficulties and yield a low ingot recovery-65% to 70%, hence small foundries avoid this material.There are a number of ways to improve the quality of aluminum scrap such as:(1 ) crushing of the scrap, which powders the brittle content , a major impurity component, followed by screening out of the dust(2) eddy current separation , which removes metals from the material flow, and(3) implement better methods for density separation.The eddy current separation and two variants of the comminution-screening technique were studied by Intermetco Ltd., Hamilton , Ontario."

Jan 1, 1986

By R. Pérez, James A. Finch, F. Tavera, Cesar O. Gomez

"Gas holdup is a variable which affects the operation of flotation columns. On one hand, gas holdup is a function of bubble size (a function of sparger type, frother characteristics and concentration, and air flowrate), tailings flowrate, solids content, and mixing patterns in the collection zone. On the other, gas holdup defines flotation kinetics and carrying capacity. Therefore, gas holdup is a useful variable to control and diagnose the operation of a flotation column, but the lack of a reliable sensor for on-line gas holdup monitoring has prevented its use in industry.This work describes the principle and the practical difficulties associated with the development of a gas holdup sensor based on the measurement of the electrical conductivity of dispersions. Two different approaches have been devised. These approaches will be described and test results presented of prototypes in laboratory and industrial columns.Background.Several years ago, a research program was initiated at McGill to use electrical conductivity as the basis for developing sensors for process measurements in mineral processing. Electrical conductivity is an intensive property which is a function of the concentration of the different phases present in a dispersion. The initial focus was on the detection of the interface between two dispersions with different characteristics (i.e., that between the collection and froth zones in flotation columns or that between clear water and sedimented solids in thickeners). The technique works in this case by searching for the location at which a sudden change in specific conductivity occurs, as a consequence of different gas holdup or solids content, and absolute values of the specific conductivity of the dispersions involved are not necessary1,2."

Jan 1, 1995

The following briefing is intended to provide an overview of the present and future challenges associated with our access to a secure and adequate supply of electrical energy necessary to support safe, productive and sustainable mining initiatives at Musselwhite. Contents ??Site power demand vs. current available supply ??Supply technical deficiencies ?adequacy and security of present supply ??Present internal generation ??Anticipated future internal generation requirements ??Increased requirements necessary for planned expansion ?demand/security ??Goldcorp?s strategy to achieve required supply ?transmission line initiative ??Subsequent benefits to others from the Goldcorp initiative. ??Economic impact of MusselwhiteMine on the northwest region ??Anticipated economic impact of planned expansion ??Expected life cycle of MusselwhiteMine ??Comparative energy costs for similar operations in other jurisdictions ??Conclusions ??Anticipated action plan ??Energy Management Initiatives ??Site Orientation

May 1, 2009

By H. O. Olsen

"GeneralTHE IRON ORE at Marmora is a replacement deposit of Precambrian limestone and is overlain with Palaeozoic limestone. It is a low-grade magnetite deposit and the ore will require concentration be-fore it can be used economically for the production of iron and steel.Present plans estimate an annual production of 500,000 tons of concentrate in the form of pellets. This will require mining approximately two million tons of ore and\ waste annually. Shipment of pellets from Marmora to a ship-loading dock at Picton will be made by rail on a year-'round basis. Shipments from Picton to the Lackawanna plant of the Bethlehem Steel Company at Buffalo, N.Y., will be carried on during the Lake shipping season.LocationThe mine, located a mile southeast of Marmora village in Hastings county, Ontario, is 31 miles north of Belleville and 3•7 miles east of Peterborough. Marmora is 130 miles from Toronto and 150 miles from Ottawa. Highway No. 7 passes half a mile north of the mine and Highway No. 14 half a mile west of the mine. The Canadian National railways' branch line between Trenton and Bancroft passes through the property just east of the open pit.HistoryThe Ontario Department of Mines conducted an airborne magnetic survey of the district during 1948 and 1949. Maps of this survey were released to the public early in 1950. Bethlehem representatives carried out ground surveys in the Marmora area shortly thereafter and in June, 1950, commenced diamond drilling."

Jan 1, 1955

By L Thompson, R C. West, T S. Kho

In 1978, the Outotec direct to blister flash (DBF) smelting process was commercialized with the commissioning of the Glogow 2 smelting facility in Poland. Since then four further DBF facilities have been constructed, two at Olympic Dam, one in Zambia and most recently one at Glogow 1 in Poland. The DBF smelting process differs considerably from conventional smelting process in both chemistry and unit operations, presenting opportunities for flowsheet capital and operating cost savings particularly when the concentrate copper grade is high. WorleyParsons has amassed considerable expertise in the Direct to Blister process and in this paper the process is compared to the modern two stage Double Flash process. The processes are modeled, and the key operating parameters, consumables and production metrics are directly compared. Subsequent flowsheets, key equipment lists and capital costs are also presented for comparison and discussion. The results show the range of concentrates which are most economically treated by the DBF process relative to those best treated in conventional processes along with those concentrates which could be treated by either process. INTRODUCTION The Outotec Direct to Blister (DBF) process was developed and installed at Glogow in 1978 (Czernecki et al., 2006). Currently there are a total of five DBFs built on three sites: Glogow No.2, Olympic Dam No.1, Olympic Dam No.2, KCM Zambia and Glogow No.1, being the most recently constructed. The DBF process was the first flash furnace process to produce blister copper and paved the way for the subsequent development of the flash converter and other continuous converting processes. Today four flash converters are in operation taking the total number of flash furnaces producing blister copper to eight. In all DBF operations it is the unique ore and concentrate composition which made selection of the DBF process the most attractive. In all cases, the concentrate is relatively high in copper but low in iron because chalcopyrite is not the major constituent. When considering smelting options for high copper, low iron concentrates a key question is then often asked, “At what point does it become economic to switch from two stage smelting and converting process to the DBF process?”

Jan 1, 2019

By I. Yarita

Magnesium alloys have the lowest density among the metals in practical use, and have properties such high specific strength, electromagnetic interference shielding and good vibration damping. Thus, there are many applications of these materials in automotive and electric parts. However, there is a little use of the products of metal forming of these materials because of poor plastic deformability in the normal temperature range and their high cost of production. To expand the range of application of products manufactured by metal forming, rolling technology for producing thin sheets having good mechanical and surface qualities is required. In this study, hot-rolled Mg-alloy sheets are experimentally rolled with or without lubrication in the temperature range from 293 K to 523 K. Rolling force, plastic deformability and surface quality are investigated, and the grain structures and their uniformity are observed. The effect of friction between the roll and the deforming material on the uniformity of the grain structure is discussed. Moreover, rolled materials are annealed and their mechanical properties are investigated by the tensile test and compared with those of as-rolled materials. The effects of the rolling conditions on the mechanical properties are discussed.

Jan 1, 2006

By T. Moyo

Ammoniacal solutions are attractive and effective lixiviants for the dissolution of chalcopyrite, allowing for the formation of stable ammine complexes with copper while rejecting iron. Chalcopyrite dissolution in ammoniacal solutions is reviewed from literature, and results from a recently completed study evaluating it through electrochemical and controlled leach studies are discussed. Ammoniacal leaching of copper ores dates back to 1916 in the leaching of low grade copper ores in the Kennecott leaching plant and in the Calumet and Hecla mines, followed by the commercialisation of the Sherrit Gordon process for the ammoniacal leaching of sulphide copper ores in 1948. Since then ammoniacal leaching has received intermittent focus from researchers with the development of the Anaconda’s Arbiter process and the unsuccessful Escondida process. In these leaching processes, the formation of surface deposits has historically been reported to result in the passivation of the chalcopyrite surfaces, whereas oxygen mass transfer in solutions has been the focus of process design improvements. Results of studies on high grade chalcopyrite material is presented in this paper which show that although a surface deposit was formed, it did not result in the passivation of chalcopyrite in ammoniacal solutions, and that while oxygen transfer is critical, it is not the direct oxidant in the reaction. INTRODUCTION Ammonia and its salts have been used in the hydrometallurgical treatment of non-ferrous metals such as copper, cobalt and nickel from oxide ores. Its chemistry allows for the selective dissolution of desired metals, leaving behind gangue including iron. Chalcopyrite is a copper sulphide ore known to be very stable and hence recalcitrant to many hydrometallurgical processing methods. Thus, the dissolution of chalcopyrite continues to be an attractive area of research. The dissolution of chalcopyrite in ammoniacal solutions is possible due to the stabilisation of copper(I) and copper (II) ions by ammonia in alkaline media. Ammonia has become more attractive as a lixiviant during the present socio-economic climate due to its low toxicity, relatively low cost and ease of regeneration by evaporation (Meng & Han, 1996). Ammonia processes are ideal when the gangue minerals are acid consuming e.g. with calcareous or dolomitic gangue (Paynter, 1973).

Jan 1, 2019

By Arash Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5 M tons. The underground mine has three active development panels and one longwall panel. The mining horizon is about 500 m below surface and strata liberate methane. Three surface-based blowing fans provide ventilation air. A ventilation survey and subsequent analysis was undertaken and a simulation model developed. Air heating during winter is essential to prevent freezing of pipelines and to lesser degree, for miner comfort. Air at all three intake shafts is heated using gas-fired heat exchangers. A strata heat study was conducted in one of the active panels to determine rock attributes. Tests included in-situ measurements of rock thermal conductivity and geothermal gradient. Continuously methane monitors have also been installed in an active development panel?s return drift. Ventsim ventilation software was used to aid the heat and contaminant simulation study. An exercise was also undertaken to gain some understanding of methane contaminant levels throughout the mine. It was further used to determine an adequate surface intake air heating rate and consequently the minimum natural gas consumption needed for winter intake air heating at the mine.

Aug 1, 2013