Search Documents

By K. Thuro, L. Wilfing, H. Kasling

"In mechanized tunneling, performance prediction is a crucial issue for estimating excavation costs and construction time of a tunnel project. The aim of this work is to compare the calculated parameters by penetration prediction models with the results of penetration tests during excavation by a Tunnel Boring Machine (TBM) at actual tunnel projects. This comparison helps to improve the existing prediction models (Gehring, 1995 and Rostami (Colorado School of Mines), 1997.) and to develop a new, so-called “Alpine Model” (research group ABROCK; Schneider et al., 2012).On-site penetration tests are a common tool to determine performance of a TBM in certain geological environments. During a test, the TBM is operated under defined conditions that allow comparing the results of different projects and machine types. There are two different types of penetration tests in use. The more common type, described by Bruland (1998a), is based on test drives at different thrust levels. The tests in this study are performed as start-stop-tests, meaning that the TBM starts from zero to the maximum possible thrust and reverse with slowly increasing respectively decreasing steps (Frenzel et al., 2012). To gain information about the interaction between TBM and rock mass, a detailed geological documentation including an analysis of the discontinuity pattern and laboratory testing for rock strength characterization are mandatory.Within the last year 16 penetration tests have been performed. The results are thrust- penetration curves (Figure 2) showing that up to a certain penetration rate only crushing occurs (subcritical penetration). From there the desired rock fragmentation process called chipping takes place (Frenzel et al., 2012). These two different fragmentation processes can be described best by a bilinear function as seen in Figure 3. Both, CSM- and Gehring-model, do not fit to the trend of the penetration rates determined during the excavation process as they are using potential or simple linear functions.Another parameter that has to be implemented into the new prediction model is the influence of discontinuities. In case of favorable orientation and spacing, discontinuities reduce the required thrust at same penetration rates. In contrast, unfavorable discontinuity systems can cause blocky faces and hence worse performance than predicted. Besides discontinuities, the toughness of rocks has to be taken into account when predicting the penetration as tough rocks need more energy to obtain complete failure than brittle rocks.Key advantage of these tests in comparison to existing are more data points in less time. By improving respectively extending the existing penetration prediction models with the stated parameters, the penetration prediction for TBMs can be more accurate and also wear calculation can benefit from this approach."

Jan 1, 2015

By I. Stefanou, J. Sulem

"In the last thirty years, the study of earthquake mechanisms has emphasized the major role of rock friction. Earthquakes appear to be the result of a frictional instability and occur by sudden slippage along a pre-existing fault or a plate interface. Multiphysics couplings play a major role in earthquake nucleation and seismic slip. The effect of shear heating and thermal pressurization may be of prime importance in the control of the stability of shear deformation inside the slipping zone. Other mechanisms in relation with thermal decomposition of minerals affect the pore pressure and the temperature evolution of the system, and can play a significant role in the extreme strain localization observed in field. The actual width of the localized zone is a key parameter for understanding fault weakening mechanisms. On the basis of field observations, laboratory experiments and recent advanced modeling, these phenomena are analyzed and discussed in order to bring some new insights in the understanding of earthquakes nucleation.INTRODUCTIONIn the last thirty years, the study of earthquake mechanisms has emphasized the major role of rock friction. Earthquakes appear to be the result of a frictional instability and occur by sudden slippage along a pre-existing fault or a plate interface (Scholz, 1998; Sykes, 1978). The conceptual model of spring slider system is commonly used to represent the interaction between an elastic crustal block and a fault zone. Stick-slip instability is possible if the softening rate of the shear resistance of the fault zone is high enough as compared to the stiffness of the crustal block. Therefore, weakening mechanisms that can explain how the frictional resistance of a fault decreases with slip and/or slip rate is of prime importance to understand how an earthquake nucleates. In recent years, several drilling programs in active faults (e.g. the Nojima fault in Japan, Boullier, 2011; the Aigion Fault in Greece, Cornet et al. 2004, the Chelungpu fault in Taiwan, Ma et al. 2006, and the San Andreas fault in the U.S.A. Ellsworth et al. 2000) as well as high velocity friction experiments (e.g. Tanikawa et al 2012a; Tanikawa et al. 2012b) have highlighted the physico-chemical processes involved in the nucleation of seismic slip (see for the example the review paper of Niemeijer et al. 2012)."

Jan 1, 2015

By S. M. Bulatovic, D. M. Wyslouzil, K. R. Rawlings

"The suitability of a new organic reagent DS20 as a depressant for oxidized and carbonaceous pyritic lead-zinc ore from Nanisivik Mines Ltd. has been evaluated in the laboratory and in the plant.The depressant DS20 is a mixture of Lignosulphonate-Dextrin-Quebracho and was developed specifically for depression of highly oxidized and carbonaceous pyrite.The laboratory test work indicated that the poor metallurgy resulting from the oxidized ore could be improved to normal plant performance by the addition of the DS20 depressant with the existing plant reagents. The laboratory data suggested that lime consumption could be reduced when using DS20.In this paper, the development work and the plant trials with DS20 are described.INTRODUCTIONNanisivik Mines Ltd. treats approximately 2000 tonnes per day of lead-zinc massive sulphide ore, containing currently 1% Pb and 9% Zn. The concentrator operations have been described previously (1,2) and typical metallurgical performance is detailed in Table I.The concentrator flowsheet (Figure No. 1) and the standard reagent scheme (Table No. 2) demonstrate the relative simplicity of treatment of this coarse grained ore.A recently discovered satellite orebody - Area 14 - containing 2% Pb and 12% Zn was brought into production in October 1983. This ore had been oxidized to varying degrees by ground water; the pyrite mineralization was found to be very fast floating and a carbonaceous constituent present in higher than normal proportion also affected flotation. The simple high lime addition could not control the pyrite, and very low grade lead concentrates resulted; zinc metallurgy was also affected by this oxidized condition (Table 3)."

Jan 1, 1986

By J. -M. Bosgiraud, G. Armand, S. Dewonck, L. Richard-Panot

"The Meuse/Haute-Marne Underground Research Laboratory (URL) is located on the eastern boundary of the Paris Basin. The URL started to be built in 2000 (shaft sinking operations) in the framework of ANDRA’s (French national radioactive waste management agency) research program aimed at determining the feasibility of a reversible deep geological disposal of high-level and intermediate-level long-lived radioactive waste (HLW, IL-LLW). Its underground drifts are used to study the Callovo- Oxfordian claystone layer between 420 m and 550 m in depth.The ongoing research program (started in 2006) following the “Technology Readiness Level” (TRL) Scale is more dedicated to technologies improvement and demonstration issue of the different disposal components, even if characterization and monitoring studies are still ongoing.In rock mechanics, at the main level of the URL (located at 490 m), construction and evolution of disposal cells of different size are studied for HLW and IL-LLW packages. A step by step approach, started in 2006, is carried out based on comparison of HM behavior of parallel drifts excavated/supported by different construction methods. These various configurations give insight of the influence of construction method on the EDZ extent and evolution and on the progressive loading of the support, which are key issues to design the Cigéo disposal drifts and excavations.The concept of disposal cells studied for HLW consists in horizontal steel lined micro-tunnels 80 m long and 70 cm in diameter. Several campaigns of tests have been carried out since 2009 in order to demonstrate the feasibility of excavating such micro-tunnels and study their behavior under different conditions (with and without back filling the annular gap between the rock and the casing, watertight or not casing). A full scale demonstrator representative of the benchmark concept has also been excavated, to study its behaviour under thermal loading with heat produced by electrical heaters."

Jan 1, 2015

By A. Atef

Vulnerability is a measure of the extent to which a community, structure, services or geographic area is likely to be damaged or disrupted by the impact of particular hazard. Current asset management practices focuses on studying factors that affect performance of isolated infrastructure networks and model a set of actions to control the expected performance of these networks. This approach ignores the underlying spatial and functional interdependencies among these infrastructure networks and their vulnerability. The purpose of this paper is to introduce a new method that recognizes the effect of spatial and functional interdependencies on vulnerability rating of water, sewer and road networks. The proposed method consists of: 1) risk assessment model, 2) interdependency assessment model and 3) vulnerability assessment model. The risk model is composed of two modules: 1) water and sewer risk module and 2) road infrastructure module. The water and sewer risk module will cluster these assets into three risk categories based on environmental, social, operational and economical factors. The road infrastructure module will cluster road assets into three risk categories by using rational factorial technique based on road type, serviceability index, traffic load, and freeze and thaw index. The interdependency model will deploy the risk ranking to perform geospatial analysis in ArcGIS which results in determining the interdependent layers of waters, sewers and roads. The vulnerability model will deploy fuzzy neural networks technique to determine the vulnerability rating based on spatial and functional interdependencies. The fuzzy neural networks are utilized to overcome the lack of historical data and incorporate experts? preferences for establishing the knowledge base for vulnerability assessment. The expected contribution of this framework is to aid decision makers in understanding the interdependencies between civil infrastructure assets and to which extent such interdependencies can compromise assets performance.

Aug 1, 2013

By D. O. DeGagné, J. F. Archibald

Spray-on polymer linings, as partial or full replacement for traditional forms of area rock support, have seen rapid growth in interest within Canada. A wide variety of lining types, ranging from polymer chemical to water-based cementitious materials, have been developed and commercially introduced to the underground mining market. Following approximately one decade of development work, several general conclusions have been reached regarding the performance of this class of area support media, these being that: health and safety assessment of the broad range of materials has shown the majority of them to be acceptable and safe for underground use; significant ground support potential can be offered by them, being equivalent to or better than capabilities offered by traditional support forms such as bolt-and-screen or shotcrete, and; their abilities to be rapidly deployed and provide near instantaneous support restraint offer considerable operational and cost benefits to underground operators. A review of currently available liner materials, their historic development within the Canadian mining industry, and overviews of support, health and safety, operational considerations and cost benefits are provided in this paper.

Jan 1, 2001

By Ken J. Brouwer

Stillwater Mining Company commenced construction and development of the East Boulder underground mine in 1998. This new PGM mine is situated adjacent to the East Boulder River approximately 35 miles south of Big Timber, Montana. Project planning and development incorporated detailed collaboration between the regulatory agencies, concerned citizens and mine personnel. A unique ?good neighbour agreement? was established with a local environmental group who have become actively involved in the review of ongoing site development and the implementation of environmental and compliance monitoring. Environmental management systems allow for integrated management of tailings, waste rock and water in order to minimize surface disturbances and to prevent adverse impacts to the East Boulder River. Long-term site development plans contemplate implementation of comingled waste rock and paste tailings. Water management capabilities allow biological treatment of all excess mine water in order to reduce nitrogen loadings prior to land application disposal by means of spray evaporation, snow making and land application. The comprehensive waste and water management plans have also been integrated with staged mine development and interim reclamation requirements.

May 1, 2002

By C. Ciriello

Six Sigma methodology, as applied within Xstrata (formerly Falconbridge and Noranda), involves a disciplined approach to managing projects, solving problems, improving performance, and leveraging information. The four (4) cornerstones of Six Sigma are the use of Philosophy (customer driven, desire to improve and discipline), Metrics (measurement systems), Methodology (scientific method and sequence of deliverables), and Tools (such as statistics, change management, and root cause analysis). This paper will outline the general steps of the Six Sigma methodology and demonstrate how each phase directly applies to a real plant metallurgical project aimed at reducing nickel losses of the rougher flotation circuit at Raglan. The main concepts of Six Sigma are described, along with the specific challenges, successes, and deliverables related to the project. It is also the authors' aim to demystify the basic Six Sigma principles.

Jan 1, 2007

By John Smith

"The RTZ Corporation PLCFrom a company's point-of-view, a good investment decision is one which results in the purchase of an asset that is worth more than it costs. Thus, in order to judge the merit of an investment opportunity, it is necessary to estimate the value of the assets to be acquired.Discounted cash flow (DCF) analysis has become widely adopted by companies in assessing potential new investments. The principle is a simple one: invest in projects which have a positive net present value, and reject those which do not. However, perhaps because of its apparent simplicity, DCF analysis is frequently misused. Good practice in the use of the technique is discussed, together with several common misconceptions.Sound analysis requires sound data; thus, the valuation process relies heavily upon a wide range of specialists to provide the basic input from which cash flow forecasts can be built up. The analyst must maintain close liaison with these specialists from the outset in order to ensure that the data provided is indeed relevant and complete.IntroductionBefore turning to the main subject of this paper ""How Companies Value Properties"", it is of interest to consider first a slightly different question ""Why do Companies value Properties""? In other words, for what purposes are such valuations prepared? Certainly the commonest, and probably the most important circumstance in which a valuation is required is when the company is considering an investment opportunity. This may be the direct purchase of a property or group of properties from a third party, but could also be the opportunity to develop a new operation or expand an existing one.A very simple objective in making any kind of investment is to make our shareholders richer than they would otherwise have been. That is, to make investments whose value to shareholders exceeds the consideration required to acquire them. Thus the investment decision focusses on the difference between an asset's value and its cost.This distinction between ""value"" and ""cost"" is an important one. Study of a company's balance sheet may tell a lot about the cost of this company's assets, but very little about their value. Then again, it is sometimes argued that a business should be bought because this will result in assets being acquired for less than their replacement cost. This merely compares one cost with another, it says nothing about value."

Jan 1, 1991

By G. Szilvay, P. Kinnunen, J. Salminen, V. Miettinen, O. Salmi, J. Mäkinen

This paper demonstrates experimental studies on bioprocessing of different waste streams. In Part I of this paper three tailings from mining industry were bioleached with mixed acidophilic culture in order to solubilize valuable metals, like copper, nickel, zinc and manganese to leaching liquor. Bioleaching resulted in > 70 %, > 85 %, 100 % and > 70 % leaching yields for Cu, Ni, Zn and Mn, respectively. However, contaminants like arsenic and chromium were not leached efficiently and they will cause challenges in residual solids and sometimes also in metal recovery from leaching liquor. Bioleaching resulted in 99 % leaching yield for copper. Part II demonstrates mine water treatment and also gold recovery from process liquids with biosorption method. The novelty of biosorption was finding that certain fungal species were able to be cultivated to self-immobilized systems, which are easier to operate than traditional suspended biomass methods. Biosorption resulted in more than 90 % removal for all contaminants, but was also seen to be gold selective.

Jan 1, 2014

By A. Majumdar, B. Servière, H. Persson

The CCR refinery, which was built in 1931, treats both internal and third party copper anodes to produce 325,000 mt of copper as cathodes. These anodes contain high levels of impurities, such as Ni, As, Sb and Bi, that reports to the electrolyte during the refining step and need to be removed in order to maintain cathode quality and operating efficiencies. In the purification plant, the electrolyte is de-copperized via electrowinning in three stages. In the last stage, the copper content of the electrolyte is reduced to below 1 gpl in order to maximize the co-deposition of As, Sb and Bi with the Cu. This is accomplished with minimum arsine gas generation by using periodic reversal of the current and by controlling the final copper content of the electrolyte. Nevertheless, the possibility of exposure to arsine is treated as a major risk and controls have been implemented to reduce this risk. This paper describes the controls in place at the purification plant, which are being continuously improved through periodic risk assessments and audits. INTRODUCTION The CCR Refinery, which is a part of Glencore Canada Corporation and located in Montreal-East, Quebec, is a custom copper and precious metal refinery, with a capacity to refine 325,000 tonnes of copper anodes per year. Copper anodes are received from the Horne smelter in Rouyn-Noranda, Quebec, Altonorte smelter in Chile and other 3rd party smelters. CCR anodes are produced using the spent anodes from the tankhouse along with purchased spent anodes and copper scrap. The precious metal plant treats the tankhouse anode slime, purchased anode slime, precious metal ingots and Doré anodes from Glencore’s Brunswick lead smelter in Belledune, New Brunswick. CCR products include copper cathodes, silver and gold bullion, a platinum-palladium concentrate, selenium, tellurium dioxide and nickel sulfate. In 1975 an accident occurred at CCR where two employees were exposed to fatal levels of arsine emitted from the then existing purification cells. This process was therefore shut down immediately. Research and development work was then initiated to determine the optimum electrowinning conditions whereby arsine gas generation would be minimized while maintaining high copper and impurity removal efficiencies. It was found that the application of periodic reversal of current (PRC) during the last stage of electrowinning retarded the onset of arsine formation while at the same time allowing the copper concentration to be reduced to less than 1 gpl (Houlachi & Claessens, 1978). A new purification plant was designed based on the PRC technology and was started up in 1976. In addition to the use of PRC electrowinning, the new plant is located in a fully enclosed section of the tankhouse. A special effort was made to design a ventilation system to evacuate the acid mist in addition to any arsine gas. Arsine monitors were installed to measure the emissions from the stack along with arsine levels in the workroom. The arsine monitors and the ventilation system were interlocked with the rectifiers (Thiriar et al., 1983).

Jan 1, 2019

By A. Scheltema Beduin, M. Kalisch, E. Floch, R. J. Dijkhuis, H. J. Oterdoom

In metallurgical copper production, the traditional aim is to increase recovery of copper to the maximum. SMS Siemag (SMS) has supplied numerous furnaces for this application. New targets are to make sure end of line products are as safe as possible with respect to health and environment, and to maximize raw material utilization. This means a for example a minimization of leachable metals in slag, so it can be safely used as a construction material, and either a targeted concentration or fixation of volatile compounds, such as arsenic. Currently, 2 process routes are generally applied for slag cleaning. The first is grinding followed by flotation, and the second is slag cleaning in an (electrical) furnace. Popularity of both options has fluctuated over the years, and currently the milling-flotation seems to be the more popular option. In this article some of the advantages and disadvantages of both methods are described, and especially how long term environmental policies could have an impact on the decision which process route to choose. Finally, this article will describe some of the developments SMS is working on in pyrometallurgical slag cleaning that could influence the direction for the design of the copper plant of the future.

Jan 1, 2014

By H. E. Johnston

There are currently a number of options in terms of plant feed comminution tests: Bond work index tests, JK drop weight and SMC tests, SPI, low impact crusher work index tests, to name a few. However, information regarding specific energy requirements for regrind mills is often requested, which can be difficult or very expensive when only a small mass of concentrate is produced from bench-scale flotation tests. This research was aimed at developing a test methodology that would produce a similar result as an IsaMill Signature Plot but require less sample mass allowing for preliminary estimates of regrinding power at a lower cost. Initially, the laboratory test methodology was completed on a single sample in comparison to the IsaMill Signature Plot for that sample. Results indicated a very good correlation between the laboratory tests and the IsaMill Signature Plot for this sample, though some parameters did impact laboratory regrind mill efficiency. The developed methodology is subsequently being applied to a range of concentrates, investigating a range of material particle sizes and material types, in comparison to a full IsaMill Signature Plot on the same sample. This new test procedure has been called ‘The Eliason Test’.

Jan 1, 2014

By J. F. Shirley

"Very seldom, if ever, is a molybdenite by-product plant operated exactly the way the process design engineer visualizes it. The best thing the design engineer can do is provide a sound, basic circuit with enough room and flexibility in order that the operating staff can make the necessary modi fi cations to optimize the process. The plant, with minor modifications, should be capable of handling more than one process. This is especially true when the client is having the plant designed for a new process.The writer would like to propose the following ten ""rules-of thumb"" for designing by-product molybdenite plants where the molybdenite is floated out of a copper concentrate. The term rules-of-thumb is used, because there are probably valid reasons for not using one or more of them in a particular plant design. In fact it was 1980 before the writer was all owed to start up a plant where all of these rules were honored in the plant design. This was after 19 years of experience in the design of molybdenite by-product processes and plants. The main reasons for not following the rules are available capital, available space, and the client's experiences based on pilot plant and laboratory test results."

Jan 1, 1981

By Reginals W. Burroughs

Diatomaceous or infusorial earth, also called diatomite; fossil meal, or kieselguhr, is derived from the lowest form of vegetable life, the unicellular alga:. It consists of the siliceous remains of extremely minute aquatic plants, which exist in both salt and fresh water. Light i~ a prerequisite to their development. These very small particles secrete silica in much the same way that molluscs secrete lime to form their shells. The diatoms at death sink to the bottom of the body of water in which they lived, and the organic matter gradually decays and is washed away, leaving the skeletons. Thousands of years are required by this means to develop bed5 of sufficient thickness to be of commercial value. The siliceous remains vary in size according to the species, but all are very minute and, as a general rule, they can be identified only under a high-power microscope. Over one thousand types have been distinguished and named. They are all composed of a hydrous or opalescent form of silica, with silica content ranging from seventy to ninety-five per cent. Magnified, they present an attractive sight, a very fragile structure with many interstitial openings known as cells. Many of them consist of two parts, defined as valves, held together by means of a girdle. Certain species, belonging to the Pinnularia family appear as a long comb, in half longitudinal section. The spaces between the teeth are the cells. This particular genus is very common in Nova Scotian deposits.

Jan 1, 1928

By D. A. Beattie

Talc is a commonly encountered gangue mineral in metal sulfide flotation. Talc is naturally hydrophobic, resulting in high recoveries if polymeric depressants are not used to specifically reject this MgO containing mineral. We have studied the adsorption of a selection of polymers onto talc using a variety of techniques. Adsorption isotherms have been determined using ex situ depletion techniques and in situ ATR-FTIR spectroscopy has been used to determine adsorption kinetics. Adsorbed layer thicknesses have been determined for the polymers on cleaved talc surfaces using the AFM. The effect of the adsorbed polymer layer on the properties of the talc surface has been quantified through contact angle measurements and single mineral flotation tests. Distinct correlations are observed between the adsorbed layer properties and the flotation performance of the polymers. These observations are discussed with reference to the bubble-particle attachment process and the molecular structure of the polymers.

Jan 1, 2006

Experimental determination of the response of an AG/SAG mill treating two components of significantly different impact resistance is challenging for two main reasons: firstly, small scale laboratory tests have yet to be confirmed as valid representations of the full scale milling environment, and secondly pilot plant testing requires 10-20 tonnes of ore per scenario which precludes the use of drill core, rendering the process very expensive. In order to mitigate these difficulties, modelling was considered as a potential way forward. However, as the JKSimMet AG/SAG model currently has no capacity to simulate the interaction of two ore types with differing impact resistance, density and/or feed size distributions, an alternative modelling approach was developed. This approach aims to essentially calibrate the AG/SAG process under a set of given conditions, for which survey data and the ore properties of the main components in the feed blend already exist. This paper describes a new conceptual model, which provides a simplified approach for investigating the multi-component behaviour of two ores of differing hardness/SG in a given AG/SAG milling environment, and which can potentially be used for scale-up from laboratory/pilot testwork and geometallurgical estimation of throughput.

Jan 1, 2012

By H. Salamanca

HighService has developed different equipment using wireless technology and machine vision systems that were specially designed to allow 1) the online determination of the SAG mills liner's service life, 2) the automatic detection of a missing dipper tooth in mineral extraction shovels, 3) the reduction of accident risk potential in the mineral transportation within the mine, and 4) the reduction of collision risk potential between shovels and wheel dozers during mineral extraction. For the development of all these systems at HighService, extensive research has been done in radio frequency and image processing fields. The integration of both technologies with the expert knowledge of the company on the typical harsh environment conditions of the mining industry has led to the development of heavy duty equipment that tolerate the extreme mechanical requirements of SAG mills and electrical mining shovels.

Jan 1, 2007

By E. Ettles

This paper features some of the spectacular new advances in the fields of fluorescent penetrant inspection and magnetic particle concentration. Casting fractures in the various stages -before the repair, during the repair and in the completed repair -using the cold process method will be discussed. This cold method of repair eliminates problems of pre-heating and cooling and the stress factors that are involved in any heat repair.

Jan 1, 1971

By J. Stachulak, M. Scobie

"This paper addresses the occurrence and indicated causes of conveyor fires in North American and European underground mines. Some significant convey or fires which have been experienced in recent years in Canadian hardrock mines are then reviewed. The nature of existing conveyor monitoring technology is considered in the context of such fire hazards. Experiences with new monitoring technology recently installed at several conveyor sites at Inca Ltd. mines are then reviewed.IntroductionFires associated with conveyors have long been recognized as a serious hazard in underground coal mines. Recently, however, there have been some significant conveyor fires in Canadian underground hardrock mines. These offer important evidence as to the nature and causes of potential hardrock mine fifes. They also warrant attention with a view to improving over-all mine design, ventilation and emergency preparedness.In addition, a new era in mine communications and monitoring technology has been entered which should offer improved capability to protect against such fires. This paper was motivated by the need to understand the causes and mechanisms of conveyor fires in order to improve their safety. This should be possible through implementing more effective monitoring systems, as well as improving conveyor design. Underground mines are becoming more intensively mechanized, with less human surveillance of equipment and a greater dependency on remote monitoring systems."

Jan 1, 1992