Search Documents

By K. Thuro, H. Käsling, C. Wieser, G. Nuijten

"The time-dependent behavior of brittle rocks during stress relaxation is of great interest for mining industry, nuclear waste disposal as well as tunneling and underground construction. Several studies have shown that both elastic as well as inelastic deformation occur during stress relaxation (Emery, 1964; Zang & Berckhemer, 1989). While elastic strain occurs already during the drilling process, inelastic deformation is time-dependent and can endure for hours, days or weeks. To investigate the evolution of microcracks during core relaxation, two crystalline core samples were recovered from high in situ stress conditions in Europe’s deepest mine in Pyhäsalmi (Finland). Samples were prepared for testing within one hour after coring such that a large portion of the time-dependent component of relaxation could be recorded over several days using ultrasonic velocity as well as acoustic emission (AE) measurements.Results from AE analysis show an exponential decrease in the number of events over a period of several hours. Repeated sudden increases of acoustic events can be related to the propagation or the interaction of cracks. In the first hours of recording also the signal energies reached the highest values and the increases in signal energy correlate well with increased event rates. On additional drill cores, P-wave velocities were measured parallel and in 45° distances perpendicular to the core axis. After core recovery, stress-induced microcracking caused an exponential decrease in wave velocities similar to AE rates. Lowest compressional wave velocities were measured parallel to the core axis and thus normal to the foliation and in the direction of the maximum in situ stress component. The highest measured velocities occurred parallel to the foliation plane. Within the samples, the anisotropy ratios were up to 1.37 at the beginning of the measurements and increased to values of up to 1.8 after 45 days. The wave velocity anisotropy is in agreement with the in situ stress orientations."

Jan 1, 2015

By A. Desbiens, M. Maldonado, R. del Villar, Aguilera. R.

This work details the application of a multiple model approach to estimate frother concentration in flotation processes. The methodology consists of identifying a set of linear dynamic models representing the effect of gas rate on the collection-zone gas holdup at different known frother concentrations (calibration step). An adaptive law is then obtained using Bayes' rule to evaluate the conditional probability that each model represents the observed system behavior. In this way, a frother concentration estimate is calculated as a weighted sum of model probabilities and their associated (known) frother concentrations. Experimental results conducted in a two-phase system using Dowfroth250C are promising. Modeling and analysis for MIBC frother are also provided.

Jan 1, 2009

By C. H. Sleeman

"The Iron Ore Company of Canada constructed a beneficiation complex in Sept-Iles, Quebec, to concentrate and pelletize earthy red hematite iron ores from the Knob Lake area. The plants were scheduled for initial production during the first quarter of 1973.Many problems have been experienced to date. Difficulties in controlling the process, excessive mechanical failures, design deficiencies and manpower-staffing problems have caused an extended start-up. The problems are now essentially solved and, with the completion of some additional minor modifications, it is expected that the plants will be producing premium iron ore pellets at or near rated capacity within the next immediate period."

Jan 1, 1976

By C. Hu

A MOS capacitor hydrogen sensor array is reported for hydrogen gas distribution mapping. Si(100) was used as substrate for film deposition. After silicon oxide growing on the silicon surface with dry thermal oxidation, palladium film was sputtered on silicon oxide as hydrogen-sensitive gate material in MOS structure. The 3x3 sensor array was patterned on silicon substrate and packaged in one chip. Sensors' response was test with impedance analyzer. The sensors in array were calibrated in the hydrogen concentration range from 10ppm to 10000ppm. The 2D hydrogen concentration distribution was obtained with the calibrated sensor array.

Jan 1, 2005

By D. Rylander

The operation of Quarry and Aggregate sites are similar to factory production, since it contains sequential production processes, tasks and activities to produce the output product. Compared to the plant though, the quarry processes are generally not synchronized and controlled towards the overall throughput of the site in real time. Some quarries control parts of the production but do generally not utilize real-time technologies for the whole site and all its activities. This fact indicates a general improvement potential in increased productivity at quarry sites, but also unsolved challenges for the same reason. The main contribution of this paper is the presentation of a Lean based method for how to describe the processes to identify control improvement potential within a site. The aim of the identified improvements is to increase overall site productivity by optimizing site, fleet and machine utilization towards the overall throughput, and minimizing operational expenses and inventories. Further the paper exemplifies the method?s usability with field studies at operational quarry plants successfully identifying and quantifying potential wastes and improvements. In addition the identified productivity improvements based on increased control and automation indicate challenges and needs in wireless communication and sensing technologies.

Aug 1, 2013

By M. Maldonado, P. Olivares

"A submersible sensor for real-time gas holdup measurement in the collection zone of industrial flotation machines is introduced. The working principle is based on the generation and measurement of a pulp flow using a gas-exclusion cell immersed in the aerated slurry. The gas exclusion cell consists of a variable-area open vertical tube designed to be filled only with pulp by preventing gas bubbles entrance. The higher density of the fluid column within the cell generates a downward flow of pulp; the rate of this flow is proportional to the gas holdup outside the cell. The gas holdup measurement is achieved by tracking the velocity of the pulp flow leaving the gas-exclusion cell, using a magnetic flowmeter. Construction details of a prototype and its testing in two- and three-phases are discussed.INTRODUCTIONFlotation process optimization consists of finding and maintaining operating conditions that maximize flotation performance measured in terms of recovery and grade. The selective separation of mineral particles proceeds in two interactive zones where different and simultaneous phenomena take place: in the collection zone, the valuable particles are separated by collection on the surface of bubbles, while in the froth zone, the bubble-particle aggregates are gathered, drained to remove entrained particles, and taken into the concentrate stream. The cell overall performance, which can be determined from proper stream sampling, is a function of the recoveries in the individual zones. These zone recoveries cannot be independently measured nor calculated from operating variables. Progress in the assessment of these recoveries has been slow because on-line and reliable sensors to measure properties of the drastically different dispersions existing in both zones are not available.In the case of the collection zone, it has been demonstrated that the recovery of hydrophobic particles on the surface of bubbles, considered as a process with first-order kinetics, correlates with the bubble surface area flux (Finch et al., 2000; Hernandez, et al., 2003; Lopez-Saucedo et al., 2012). Bubble surface area flux (bubble area generated per unit time and cell cross-sectional area), is a variable affected by gas flow rate, bubble size distribution, and frother type and concentration. Gas holdup (volumetric fraction of gas dispersed in the slurry) is also affected by the same variables, and as such, carries information on the interacting variables that define the performance of the process. Therefore, a correlation between gas holdup and bubble surface area flux was expected and demonstrated (Finch et al, 2000), and since gas holdup is easier to measure as no bubble size is required, it has the potential to be the basis of a cell control and optimization strategy if a continuous sensor is available."

Jan 1, 2016

By C. B. Webber

"Sherritt Gordon's experience with rubber mill liners began in 1964 at the Lynn Lake Farley Mine and continued at the Fox Mine in 1960, and the Ruttan Mine in 1973. This paper describes the history of the performance of rubber mill liners at the three mine operations.LYNN LAKE - FARLEY MINEThe Lynn Lake Farley Mine, which ceased production in 1976 due to exhausted ore reserves, was a 3500 T.P.D. copper-nickel operation; consisting of two parallel rod mills followed by three stages of ball mill grinding. A circuit modification in 1964 necessitated one of the tertiary ball mills to be used as a pyrrhotite regrind mill. This 8' x 5' Hardinge conical mill drawing 225 HP was initially installed with steel liners and lifters. After several months of operation a routine inspection revealed severe channeling and washing behind the liners which was threatening to erode the ball mill shell. It was thought that the highly acidic condition in the mill, due to grinding 100 º6 pyrrhotite, was accelerating the wear of the steel liners. At this time it was decided to reline the mill with rubber liners to see if the wear problem could be relieved, and in December 1964 a set of Skega rubber liners were installed."

Jan 1, 1981

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019

By M. E. Holter

"Three main potash members are recognized within the Prairie Evaporite Formation of Saskatchewan and have been designated, in ascending order, the Esterhazy, Belle Plaine and Patience Lake members. Each is composed of sylvinite near the geographic center of the member and becomes increasingly carnallitic marginally. Each stratigraphically higher member has a narrower carnallitic margin. The sharp contact between carnallitic and non-carnallitic components of the formation describes a surface which may be traced regionally and is not related to bed-ding. The contact rises higher in the stratigraphic section toward margins of members. Within each of the three members, analyses indicate that carnallite becomes more abundant toward the north whereas sylvite and insolubles, increase toward the south. Within each member, areas rich in carnallite are coincident with areas in which the member as a whole is thicker than averag,e. The Belle Plaine Member contains the highest concentrations of carnallite, the Esterhazy the lowest. A maximum content of about 30 per cent sylvite is common to all three members. Insoluble contents increase in successively higher members.Map studies are combined to outline the economic potential of the potash beds in terms of depth to the top of the Prairie Evaporite, ""salt-back"" thicknesses and sylvite grades for each member."

Jan 1, 1971

By Ron Hatch, M. K. Witte

"INTRODUCTIONThe proper selection of carbon for a gold carbon in pulp (CIP) circuit involves careful evaluation of several physical, chemical and economic factors. A series of evaluations are required to maximize gold recovery at the lowest capital and operating costs, whether the carbon is selected for an existing gold mill circuit or a new mill under design.Although evaluation may proceed through various stages, it is the intent of this paper to outline some of the preliminary testwork that should be carried out to screen potential carbons for a particular application.An examination of the specification sheets supplied by the various carbon manufacturers may indicate some desirable properties on which to make cursory selection. This exercise by itself will not provide the basic data needed for selecting the best carbon for a particular ore pulp and metallurgical circuit. The necessity of further metallurgical evaluation is indicated by the fact that different carbons perform differently depending on the physical and chemical nature of the leach pulp. In the case of an existing mill, actual leach slurries using mill water are available and should be used for testwork. In the case of new mills, leach pulps must be prepared to simulate the proposed circuit.Five coconut shell activated carbons were obtained from various suppliers, all reported to be 6 x 16 mesh carbons recommended for CIP circuits. A metallurgical evaluation was made utilizing two leach pulps with significantly different characteristics. This paper describes the test procedures utilized and the results obtained from the testwork."

Jan 1, 1985

By Alfred B. Annor

The introduction and application of paste backfill over the past two decades has resulted in substantial benefits being realised by many backfill reliant mining operations who have used this technology. Paste preparation over this time period has relied basically on mechanical dewatering approaches that have included the use of centrifuges, thickeners, and vacuum and pressure filtration. In large bulk mining operations, this method of paste preparation has usually involved the construction of big and complex surface plants to meet large tonnage demands. These large plants usually have attendant high capital, maintenance and operating costs. The application of paste backfill in narrow-vein mining requires more flexibility in terms of fill preparation, transportation and placement. The method of paste fill preparation should take into consideration low manufacturing and operating costs, ability to use existing facilities at mine sites, simplicity of operation and flexibility of preparing fill over a broad range of consistencies. This paper will review alternative paste fill preparation methods and indicate those that might be better suited to narrow-vein mining.

Oct 1, 2001

By A. L. Mular

"On behalf of Bob Bruce and myself I would like to begin by stressing some key points.First, most of us know that the Canadian Mineral Processors was formed in 1969 and is an offshoot of the Canadian Gold Metallurgists. I attended that first meeting in 1969, and I haven't missed a meeting since! Pretty obvious that CMP serves the best booze! At any rate, we know that our meetings are supported by CANMET. Camsell Hall is always at our disposal; Bob Bruce acts as permanent secretary pretty much free of charge; we receive a financial grant from CANMET. This brings me to a second point.Second the Canadian Mineral Processors do not enjoy a free ride in this relationship. CMP provides a genuine service to the mining industry, to government, and to universities. For the industry, CMP serves as a forum for the rapid dissemination of new ideas and new technology developed at remote locations throughout Canada. New developments outside Canada are introduced by invited speakers at our meetings. The effect is to help reduce operating costs and increase efficiency.For government, problem areas and research priorities can be isolated through mutual discussions. Direct communication at our meetings can help CANMET to temper its goals and modify its national priorities.For universities, CMP provides a wealth of operating experience and practical know how. The yearly proceedings are a major current reference source fo1· those of us who teach mineral processing. Admittedly, the proceedings are publ-shed from CMP coffers. However, I note that our fees are up this year, which brings me to a third point.Third, we face some potential problems of a financial and political nature. From a financial view, we may lose our CANMET grant and other financial good will simply because of spending constraints. Our fees are expected to climb each year thereafter.From a political view, we know that the metallurgical society of CIM is anxious to incorporate CMP as a section. The pros and cons of such a merger have been described in a recent mailing. In th2 final analysis, the political and financial problems are interrelated. There are several alternative solutions to both problems, which brings me to a fourth point"

Jan 1, 1979

By J F. Short

The jet piercing process, developed by Union Carbide Canada Ltd., is well established in blasthole production in open-pit mining. By this process, holes can be drilled, shaped and chambered for blasting. In suitable ore or rock formations, a considerable cost reduction can be achieved. This paper reviews the equipment used, relates how cost savings may be accomplished, and concludes with a mention of the most recent developments in this field. JET piercing and chambering, a process for blasthole production in open-pit mining, leads, in many instances, to improved drilling and blasting techniques and costs. It is a method of working rock with a supersonic flame and, to be most effective, depends upon a characteristic of the rock called spallability. Spalling, in this case, is the breaking away of surface particles from the rock body due to stresses caused by the thermal shock of the jet flame. Various rock properties contribute to this action, but, in general, the harder the rock the greater the spallability and the more effective and economical is the jet process. The jet process has the capability to drill, ream, shape and chamber holes for blasting.

Jan 1, 1965

1.Overview of the Ministry of Energy, Mines and Petroleum Resources (MEMPR) 2.First Nations Perspective 3.Revenue Sharing Framework 4.Economic and Community Development Agreements (ECDA?s ) 5.Questions? The Ministry of Energy, Mines and Petroleum Resources (MEMPR) MEMPR manages the responsible development of British Columbia?s energy, mining and petroleum resource sectors. Through the promotion of teamwork and positive working relationships with our clients, MEMPR facilitates a climate for thriving, safe, environmentally responsible and competitive energy, mining and petroleum resource sectors. Works closely with others in Government (e.g.. Integrated Land Management Bureau) to engage First Nations in consultation processes as well as revenue sharing negotiations.

May 1, 2010

By Les F. Sawatsky

Surface drainage, particularly mine closure drainage, must be properly considered during all stages of mine planning because it presents constraints that are critical to economic mine operation, minimizing environmental impacts and ensuring compliance with government regulations. Deficient mine site drainage increases costs of operation, causes unnecessary environmental impacts and may result in regulatory violations. The scope of this paper includes stream diversions around mine areas, drainage systems within the mine disturbed footprint, and closure drainage works to control surface water, ground water, erosion, sedimentation, and seepage discharges following mine operations. Developing selfsustaining drainage facilities upon mine closure, requires a mine plan that develops appropriate topography and constructed drainage courses that replace the function of pre-disturbance drainage systems without aggravated erosion and deterioration. Drainage criteria, particularly closure drainage criteria, represent important constraints on mine planning and are best considered by integrating drainage features into the mine plan well in advance of mining activities. Integrated mine planning by a multi-disciplinary team is recommended to achieve closure objectives at minimum cost and maximum effectiveness The geomorphic approach to channel design is an effective means of providing a drainage system that has the appearance, function and longevity of natural systems. By incorporating this technique into closure drainage planning, mine operators can construct sustainable (walk-away) drainage systems that require little or no maintenance in the long-term. This paper presents a process by which drainage criteria and associated mine plan constraints can be integrated into the mine planning process. This paper outlines the process for detailed design of drainage facilities, particularly closure drainage systems that are designed by the geomorphic approach.

May 1, 2009

By Karol Kostúr

This paper briefly describes the current state of underground coal gasification (UCG) processes globally and in the Slovak Republic. Recent results of laboratory and technical tests are presented. In addition, on site measurements have added new knowledge of UCG technology. A series of laboratory tests based on physical models shows promise for managed UCG process control.

Aug 1, 2013

By L. J. Surges, C. Bazin, D. Hodouin

"A kinetic model was developed for the conditioning and flotation processes of an industrial lead concentrate dezincing circuit. The models were incorporated into a flowsheet simulator. Simulation results demonstrate the advantages of split conditioning of coarse and fine particles and the potential of this approach for the production of the heuristics required for the development of intelligent control strategies.The conditioning model relates the proportions of activated and hydrophobic surfaces and residual reagent concentrations to activator and collector reagent flowrates. The model accounts for the solids and water flowrates, and for the solids grade and size distribution. The flotation model uses the predicted proportion of hydrophobic mineral surface, the aeration rate and the froth depth to estimate cell, bank and circuit performances. IntroductionFlotation has been the object of modelling and simulation studies for more than two decades. The process is usually modelled as a kinetic one in which the particle flotation rate constants are key parameters. Rate constants are related to the operating variables (pH, reagent flowrates, aeration rate, etc), however these relationships are seldom established in the literature.In spite of the large amount of literature on flotation modelling and simulation, few papers deal with the interaction between flotation rate constants and operating variables. This important gap, which was identified in the early seventies by Woodburn (l970), still exists. One of the first attempts to include operating conditions in a flotation simulator was made by King (l973), who explicitly introduced the aeration rate into an air bubble loading model. Lynch et al. (1981) used an empirical model to relate the proportion of slow floating particles to the ratio of collector per ton of ore. Such empirical relationships are difficult to calibrate and cumbersome to use when an activator and a collector are added to slurries in which particle size distribution and surface characteristics are changing. Eascur and Herbst (l982) relate in a fundamental way the mineral flotation rate constants to the aeration rate, froth depth, agitation and frother concentration, however the model does not account for reagent flowrates. Niemi et al. (1982) have proposed a model for the conditioning of minerals and included it into a conventional flotation simulator."

Jan 1, 1988

By J. Olaf Sund

"THE November issue of the Bulletin carried in it ""Origin of the New Bruns1viclc Gypsum Deposits"" by J. Olaf Sund. This paper was a digested account of a Master's thesis at the University of New Brunswick which was a very useful compendium of information of gyp-sum in New Brunswick. It was a warded the President' s Gold .Medal and the First Prize in the Graduates' Section of the Students' Essay Competition. The present writer presents his congratulations to the winner of the competition. At the same time he must comment on the use of certain terms and on certain conclusions presented in the paper.The term ""unconformable"" has been used in several places in the paper to describe the relationship of gypsum to anhydrite in various deposits in New Brunswick in a sense which is quite alien to the accepted meaning. It has long been known tl1at the gypsum at the surface or near the surface in deposits in the Atlantic Provinces has come from hydration of anhydrite by surface and ground waters. The gyp-sum must be looked upon then as an alteration or even a weathering product. It cannot in this sense be called ""unconformable"" and thus arguments using the word in the accepted sense are invalid."

Jan 1, 1960

By L. A. Gomieroa

The Caetité-Brazil uranium facilities produce about 340 t/y of uranium from an ore averaging 0,25 U %. The process steps are ore crushing, heap leaching with sulfuric acid, U separation and purification by solvent extraction with tertiary amine followed by stripping with sodium chloride solution and precipitation as ammonium diuranate that is dryed. A change in the milling process is being evaluated to increase the production and the uranium recovery. Heap leaching will be changed to conventional tank agitated leaching of the ?590 ground ore slurry in sulfuric acid medium. The replacement of the stripping reagent is also being considered.

Aug 1, 2010

By P. A. Christopher, R. H. Pinsent

"The Adanac molybdenum porphyry deposit near Atlin, in northwestern British Columbia, was discovered in 1905. It was explored extensively between 1967 and 1980.The deposit is within a complex, multi-phase, quartz monzonite stock that is a satellite of the post-accretionary, Surprise Lake Batholith. Biotite K-Ar dates range from 703 ± 2.4 Ma to 71.6 ± 2.1 Ma, indicating a Late Cretaceous age of emplacement.The deposit comprises an irregular-shaped ring or halo peripheral to a quartz monzonite porphyry dome, or ""cupola': The shape of the ring, and of a smal~ fine-grained quartz monzonite intrusion, and the presence of higher-grade mineralimtion on the eastern flank of the cupola, suggest partial control by a preminera/ structure. The deposit is truncated by a steep, northwesterly dipping, normal fault (Adera Fault) that down-dropped the northern half of the deposit by a minimum of 100 mThe deposit lacks strong zonal alteration but there are narrow envelopes of potassic alteration around some veins and local zones of intense wall-rock silicification. There is considerable retrograde alteration along postminera/ faults and fractures.Molybdenite occurs in veins and fractures, many of which are relatively flat-lying. They occur in all phases of quartz monzonite. Molybdenum is the only element of economic significance. There are vein and skarn occurrences with tungsten, tin, lead, zinc and precious metals peripheral to the deposit.In 1981, Placer Development Limited reported an ""undiluted mineable mineral reserve"" of 151 971 000 tonnes grading 0.063% Mo at a cutoff grade of 0.04% Mo and a strip ratio of 1.5:1."

Jan 1, 1995