Search Documents

By James F. Allan

"Abstract -The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec . Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by ? 0.10% Y203, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% Zr02. The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and cale-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and rninor britholite. Yttrium also occurs in britholite in cale-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By M. Y. Williams

Introduction During the economic investigation of Pacific Great Eastern Railway subsidy lands, the P.G.E. Survey of Resources made a geological and mineral survey of a large part of the valley of the Peace river as included in the Province of British Columbia. The immediate valley of the Peace river was surveyed from the mountains to the Alberta boundary; the valley of the Pine river was surveyed throughout; and the Dominion block, 70 miles square and lying astride the Peace river, westward from the Alberta boundary, was very carefully surveyed. The writer was in general charge of the field work, and spent half the field season of 1929 and the field season of 1930 in the region . J. B. Bocock, however, did the major part of the work, spending two seasons, 1929 and 1930, in the area. General Conclusions The rock formations within the area discussed are all sedimentary and range in age from pre-Cambrian to recent. As might be expected, the minerals are in the main non-metallic, coal being by far the most important. Favourable conditions exist for natural gas occurrence, and suitable structures for petroleum concentration occur, although the high carbon ratio of the coals sheds considerable doubt upon the actual occurrence of oil in the area. Materials of minor interest are ochre, calcareous tufa, marl, limonite, gravel, and building stone.

Jan 1, 1934

By C. A. Anderson, C. A. Young, H-H. Huang, L. G. Twidwell

An equilibrium calculational computer program (STABCAL) can be used for titration simulation. The program can handle various forms of titrants: solid, aqueous, gaseous or another solution, and various type of reactions: reductive, oxidative and adsorption. Background chemistry, mathematical considerations, and program development will be illustrated. Also, simple titration applications such as how to determine the acidity of aqueous solutions and alkaline sulfide leaching of gold are presented. Processing of an acid mine water from the Berkeley Pit in Butte, Montana has been used for illustration purposes. The treatment studies included: cementation, sulfidization, and neutralization. The calculational results for the neutralization treatment using various alkaline reagents are compared to actual experimental data and potentially appropriate processes are discussed. Computational

Jan 1, 2005

By W. B. Xie

The hardening behaviour and microstructure evolution of Cu-30Ni-30Mn alloys aged at 350 °C has been investigated utilizing optical microscope, scanning electron microscope, transmission electron microscopy and Vickers hardness tester. The results show that the discontinuous precipitation of NiMn phase results in a remarkably hardening effect in Cu-30Ni-30Mn alloy during aging at 350 °C. The maximum hardness (~494HV) is attained in the sample after aged for 48 h. The NiMn precipitates are ordered and have a face-centered tetragonal structure. The coherent orientation relationship between the NiMn precipitates and Cu matrix is (220)Matrix // (220)P, [1-1-2]Matrix // [1-1-2]P. In addition, there is a linear relationship between hardness and volume fraction of the discontinuous precipitation, which indicates that the hardness increment of Cu-Ni-Mn alloys aged at 350 °C is attributed to the microstructure characteristics of discontinuous precipitation. The high strength of discontinuous precipitation colony is caused by the formation of nanoscale NiMn precipitates with a lamellar structure in discontinuous precipitation. INTRODUCTION Cu-Ni-Mn alloys are attractive candidates for oil drilling, aerospace and energy applications due to their high elasticity, high strength and excellent corrosion resistance (Sun et al., 2009; Liu, Yang, Xia, Jiang, & Gui, 2016). The high strength of the Cu-Ni-Mn alloys is mainly attributed to the precipitation of NiMn phase (Shapiro, Tyler, & Lanam, 1974; Xie et al., 2015). The uniformly dispersed nanoprecipitates formed by continuous precipitation can impede dislocation movement, and thereby lead to a significant improvement in strength of traditional precipitation-strengthened alloys. However, it is reported that there are two precipitation types observed in Cu-Ni-Mn alloys, namely, continuous precipitation and discontinuous precipitation (Shapiro et al., 1974). The discontinuous cellular colony with a lamellar structure nucleates at grain boundaries, and progressively grows inward the grain on the process of discontinuous precipitation (Ng, Bettles, & Muddle, 2011). It is found that the discontinuous precipitation can occur in many Cu-based alloys, such as Cu-Ni- Mn alloy (Shapiro et al., 1974), Cu-Be alloy (Monzen, Hasegawa, & Watanabe, 2010) and Cu-Ni-Sn alloy (Zhao, & Notis, 1998). Many studies consider that the discontinuous precipitation results in a detrimental effect on hardness and strength, and the discontinuous precipitation occurring during aging treatment should be suppressed (Markandeya, Nagarjuna, & Sarma, 2004; Semboshi, Sato, Iwase, & Takasugi, 2016). The mechanical properties can also be improved by discontinuous precipitation in AZ91 magnesium alloy (Tamura, Kida, Suzuki, & Soda, 2009) and AM30 magnesium alloy (Saikawa et al., 2012). Jun (2017) found that the reduced interlamellar spacing of precipitate fibers in discontinuous cellular colony leads to a significant increase in hardness. Indeed, the strengthening contribution of discontinuous precipitation is similar to that of continuous precipitation in Cu-20Ni-20Mn alloy. Discontinuous precipitation of NiMn phase can provide a significant strengthening effect in Cu-Ni-Mn alloys.

Jan 1, 2019

By Howard W. Tipper, Richard B. Campbell

"The Quesnel Trough is underlain by a thick sequence of mainly Upper Triassic and Lower Jurassic volcanic-clastic and sedimentary rocks that lie between the highly deformed Proterozoic and Paleozoic rocks in the Omineca Geanticline to the east and the Upper Paleozoic Cache Creek Group in the Pinchi Geanticline to the west. Broad areas of the Trough between Kamloops and Williams Lake are covered by Eocene volcanics and sediments and by Miocene-Pliocene plateau lava. Granitic intrusions were apparently mainly confined to two major episodes; one about 200 m.y. ago (coeval with the Guichon batholith) and one about 100 m.y. ago. In addition, the region includes small granitic and syenitic intrusions, some porphyritic, that may be all or partly still younger. Exposures in the region are generally small and scattered, obscured by widespread, not necessarily thick glacial deposits. This, together with the extensive Tertiary cover, makes prospecting difficult. The part of the Quesnel Trough discussed here is the direct northwest-ward extension of the copper-rich Kamloops-Merritt-Princeton region. It contains the Boss Mountain molybdenum mine, related to a breccia zone induced in a batholith of the oldest group by a younger intrusion, and the Cariboo Bell copper deposit in Lower Jurassic volcanic-elastic rocks and syenitic intrusions. The Gibraltar deposit, in a 200-m.y. intrusion, is within the Pinchi Geanticline close to the margin of the Trough. Molybdenum prospects are mainly restricted within or near the 100-m.y. granitic rocks. Copper prospects, on the other hand, are most prominent in the volcanic-elastic rocks and in the 200-m.y.-old granitic rocks, although they can also be spatially related to younger intrusions. Copper thus has a wide potential distribution.The writers believe that the region is deserving of careful and comprehensive exploration by directly applying the knowledge and techniques developed in the important producing areas to the south. All of the major pre-Tertiary geological elements seem to have potential for mineral deposits; none should be ignored. A thorough knowledge of the thickness and distribution of the Tertiary rocks and the development of geophysical methods to ""see through"" them is of particular importance."

Jan 1, 1970

By Jean-Jacques Bouillon, Michel Jébrak, Stephane Faure

"Le gisement polymétallique (Cu-Zn-Au-Ag) des Mines Selbaie est forme par un réseau de filons encaisses dans une séquence de pyroclastites felsiques du sill on Harricana-Turgeon. Les minéralisations sont encaissées dans le tuf de Selbaie, situe sous une épaisse séquence d'ignimbrites Iitées. Ce gisement se distingue des autres gites archéens par une chronologie atypique des minéralisations: les veines de chalcopyrite, de sphalérite et de galène recoupent un amas exhalatifpyriteux stérile. Un vaste halo d'altération hydrothermale a chlorite et mica blanc est associe à cette minéralisation.La mise en place des veines minéralisées est associée à une phase d'extension NNW-SSE. Le complexe volcanique subit, par la suite, trois phases de déformation. Une compression, orienté N-S, développe une schistosité à peine pénétrative et un réseau de fentes de tension. Une réorientation des contraintes locales selon une direction WNW-ESE conduit au chevauchement de I' écaille d'andésite et de tonalite de Brouillan. Un réseau conjugue de failles normales cassantes est associe au relâchement des contraintes."

Jan 1, 1990

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By V. T. Panayotov, M. I. Panayotova

Wastewater from mining and mineral processing activities is often polluted by anion forming metals, such as molybdenum and chromium. Low cost materials, including zeolites, are studied for removing heavy metals from wastewater. It is widely accepted that natural zeolites are not effective in removing metals in anionic form. The paper presents study on use of metal modified natural clinoptilolite to remove Mo (VI) and Cr (VI) ions from model soft wastewater. Modification with Pb, Fe(III), Zn and Ba increases clinoptilolite uptake capacity with respect to Mo(VI) at low pH values of the water subjected to treatment, the efficiency decreasing in the order Pb > Fe(III) > Zn > Ba. Only lead-modified clinoptilolite shows high uptake of Mo(VI) in acidic, neutral and slightly alkaline conditions. Modification with Pb, Ba and Fe(III) increases zeolite uptake capacity with respect to Cr(VI) from neutral water. The effectiveness of Ba-modified zeolite decreases in slightly acidic water. Over 90 % uptake of initially available Cr(VI) is achieved by lead-modified clinoptilolite both under neutral and slightly acidic conditions. Increasing the initial pollutant concentrations increases the removed amount both of Cr(VI) and Mo(VI) for Pb-modified clinoptilolite. The findings could be a basis for using the natural clinoptilolite to remove in consecutive steps: firstly Pb(II) and/or Fe(III) ions and then loaded zeolite to be used for Mo (VI) and/or Cr(VI) removal. The kinetics of Mo(VI) uptake by CL-Ba, CL-Fe(III), CL-Pb, and CL-Zn is best described by the pseudo-first order kinetic equation. The kinetics of Cr(VI) removal by CL-Ba, CL-Fe (II), CL-Fe (III) and CL-Zn is best described by the pseudo-first order kinetic equation. Kinetics of Cr(VI) removal by CL-Pb obeys the equation for the first order irreversible reactions. Finding way to remove anions-pollutants from the mineral processing wastewater will render this industry more environmentally friendly and socially acceptable.

Jan 1, 2016

By Kadir Sariiz

Abstract - The Akçayir-Yürükakçayir Miocene-Pliocene basin in the Central Anatolia hosts ancient lacustrine sepiolite deposits. The succession in this basin consists of conglomerate (Yürükakçayir conglomerate), clayey and silty limestone, dolomitic marl, sepiolite beds and lenses, and dolomitic limestone (Kepeztepe formation). The main impurities within the sepiolite rock are dolomite, opal-CT, calcite, smectite and feldspar as sepiolite + dolomite and sepiolite + opal-CT are the main mineral assemblages. Smectite and feldspar are thought to be of detrital origin. Calcite is found as a secondary filling in root tubes and casts. Sepiolite samples studied display root-marks and root tubes, soapy and massive structure indicating direct precipitation. Sepiolite deposits probably formed at a pH of 8 to 9, and Mg+2 and SiO2 concentrations in moderately saline environments of internal facies of an alkaline lake.

Jan 1, 2000

By B. H. Weber

"Industry generally has become noise-conscious and is realizing that damage to the human ear is expected to become more costly than any other compensation. Noise control has been recognized as a necessity and, fifteen years ago, in co-operation among different countries, inter-national organizations were set up to co-ordinate measures against dangerous noise and the development of silencing devices began. Rock drills for underground operations were particularly scrutinized because of the explosive nature of the noise developing from air escaping from exhaust. This paper describes the results and the present stage of development in the reduction and control of noise on rock drills, with special application to their use in mines."

Jan 1, 1970

By K. Adham, T. Buchholz

"Significant capacity increases to meet new production demands can often be fulfilled through debottlenecking of an existing production facility, rather than the more expensive option of building new plants and facing new environmental and infrastructure challenges. To achieve that goal, it is important to model and calculate the existing ultimate capacity of each processing plant area, and that of each key equipment sector within the plant areas. This paper describes a methodology of how process modeling tools can be used to simulate the processing steps, how to estimate their existing and ultimate capacities, and how to determine the sweet-spots (minimum cost points) for a plant expansion – leading to a road map of the subsequent debottlenecking project implementation.The debottlenecking technique is presented through a generic work-flow narrative which can be applied to different mineral processing studies, starting with establishment of heat-and-mass balances, drawing a bottleneck diagram, brainstorming capacity increase options, and preparing a cost-capacity curve. Hatch has successfully applied this technique to a number of plant capacity studies, with great benefits to our industrial clients.INTRODUCTIONWith the softening of the metals and minerals prices, and the escalated costs of building new processing plants, it is now economically more viable to improve and debottleneck the existing facilities, rather than build new ones. However, spending new money on old plants requires careful considerations, in order to identify the most economically advantageous incremental steps of improvement and the best potential returns on investment. Process modeling, hand in hand with plant measurements, can identify the best scenarios to balance the three aspects of plant capacity (nameplate, utilization and yield), both at the global and the individual system and subsystem levels."

Jan 1, 2016

By M. Grenon

OBJECTIVE ?To link slope stability and financial assessment algorithms into a commercially available mine design software packages to provide integrated global pit optimization.

May 1, 2013

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015

Objectives ? New deposits can be found in mature Mining CampsNew Camps ? Volcanogenic Massive Sulfide (VMS) deposits ? polymetallicpolymetallicexamples are desirable exploration targets examples ? Genetic and exploration models for VMS deposits are robustrobust ? subtle but important differences exist between deposits and districts ? sometimes ??neglectedneglected??in resource modeling and exploration efforts ? ReRe-evaluation of a prominent existing camp is rewarding ? update on the exploration strategies currently being applied on a practical level The Falconbridge-Alexis approach includes GoCAD modelling

May 1, 2006

By S. Eckert, M. Reuter, D. Obiso, S. Kriebitzsch, M. Akashi

The present paper focuses the application of CFD techniques to investigate the Top-Submerged- Lance (TSL) gas injection in liquid metal. Previous works of the authors have shown that up- and down- scaling procedures based on the modified Froude number have some shortcomings, as this approach does not take into account the interfacial and viscous forces. Indeed, surface tension and dynamic viscosity of the smelting slags (σ = 0.4-0.5 N/m, μ = 0.2 Pa·s) are higher than the operating fluids that have been used in literature (water, paraffin oil) to study TSL injection in down-scaled furnaces. In order to get closer to real systems, the authors study the TSL injection of Argon in a liquid metal. An experimental campaign was carried out in the X-ray lab at Helmholtz-Zentrum Dresden-Rossendorf (HZDR), where the eutectic alloy GaInSn was used as liquid phase. The alloy is liquid at room temperature, and X-Ray imaging is used to picture the multiphase flow in a quasi-2D vessel. The aim of the present work is to demonstrate the applicability of CFD techniques to model multiphase flows involving liquid metals, and validate the model using the data produced at HZDR. The commercial software ANSYS Fluent® was used together with the Volume of Fluid model to directly resolve the gas-liquid interphase. Some features of the flow, such as the void fraction distribution and bubble detachment frequency are tracked with CFD and compared to the experimental data. INTRODUCTION In the last thirty years the TSL smelting technology has increasingly been used for industrial non- ferrous smelting processes and is now one of the significant pyrometallurgical processes. Developed in the early 1970’s at CSIRO, the furnace is nowadays commercialized in different market sectors, including copper and lead smelting, zinc fuming, waste treatment and slag recovery (Floyd, 2005). Despite the wide application of these reactors in the pyrometallurgical market, some aspects of the process are still not fully clarified, since in-situ measurements and optical accesses are prohibitive because of the high temperatures and aggressive conditions. Phenomena such as the bubbling regime, the slag solidification and the submerged combustion still need a deeper scientific investigation to obtain a better understanding of the process.

Jan 1, 2019

By B P. Scott

Podsol soil horizons developed on Pleistocene glacial sediments overlying the Coronation Mine orebody were analyzed for copper and zinc spectro-photometrically, using biquinoline-isoamyl alcohol and dithizone carbon tetrachloride reagents. Copper and zinc are concentrated in the A. and C horizons, whereas the A1, A2 and B horizons are leached. Of economic significance is the fact that the C horizon contains a copper anomaly, in excess of 100 times back-ground, directly over the orebody. Due to the erratic distribution of high copper concentrations in the Ao horizon with respect to the orebody, that horizon is not considered as a reliable prospecting datum. U NDER certain conditions, metallic ore deposits are accompanied by primary halos of trace elements in unweathered rock surrounding the orebodies or by secondary halos in weathered rock, alluvium, soil, or vegetation above or near the mineralized zones. Where such halos occur, chemical analysis, as applied to the detection of trace elements, is a valuable prospecting aid, permitting the detection of mineralization of possible economic value.

Jan 1, 1965

By C. Boudreault, M. Fortier, S. Fafard

In the forging industry, the increasing trend is to use DC cast billets as forging stock to replace extruded stock. However, there is little technical information available in open literature. In order to gain a better understanding of the behaviour of cast stock during deformation, a study was initiated to evaluate the impact of an homogenisation treatment on the billet prior to cold forging. Axisymmetric upsettings of cylindrical samples machined from DC billets were achieved in order to evaluate and compare flow stresses, crack initiation and propagation. Results show a 30% decrease in flow stress after homogenisation. Observations of the deformed samples show major cracking for the as-cast material. Optical microscopy and SEM observations have related the crack initiation to decohesion around ß -AlFeSi particles and subsequent growth along the constituent path. Homogenisation effectively breaks up and transforms the ß phase, present as platelets in the cast product, into smaller spherodised a-AlFeSi particles. This has the effect of preventing crack growth in the forged product. The homogenisation treatment also resulted in the reduction of Mg and Si in solid solution. The softer matrix generated 29% less die wear when compared to the as-cast structure. Based on the results of this study, it is thus recommended to homogenise cast billets prior to cold forging.

Jan 1, 2006

By Derrin A. Auerswald, Jacolien P. Wyethe, Nanne M. \/egter

Base and precious metal refineries often produce effluent solution and slurry streams containing between 50 mg/L and several grams per liter of base metals. Metals have historically been precipitated from these streams with lime to produce effluent streams at pH values between 8 and 9. This effluent treatment process generally does not remove alkali and alkali-earth metals or halides efficiently and with more stringent environmental legislation, more sophisticated effluent treatment plants must be considered which could for example incorporate sulphate removal with ultra-filtration, or the SavminTM process, followed by reverse osmosis for the removal of halides. The flowrates of effluents are often high and if base metals can be recovered before neutralization, the revenue generated from this stream can reduce the cost to produce clean water significantly, and in the case where high concentrations are disposed of, result in a profitable operation. As an add-on to an existing the plant the recovered metal is upgraded and recycled to the plant, but the production of a saleable metal can also be considered. Technology selection for metal recovery depends on the composition and flowrate of the effluent, but could incorporate resin-in¬pulp or other ion-exchange technology; precipitation as sulphides, hydroxides or carbonates; or solvent extraction. This paper describes, as a case study, the technology selection process and uses data from Zincor. Zincor is a division of Exxaro Base Metals (Pty) Limited, a subsidiary of Exxaro Resources Limited.

Jan 1, 2011

By Michael Loken, April Montera

"The process of blending consistent and predictable feed for the roasters is critical to optimizing product quality and controlling production costs. To assist in this process, Online PGNAA Slurry Analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100% of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their Full Stream, Elemental Slurry Analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced."

Jan 1, 2016

By P. Simon, G. Falkinger, G. Angerer, B. Gerold

"This contribution presents an investigation of the evolution of shrinkage pores during hot rolling with a special focus on the microscopic mechanism. The reliable closure of pores, which inevitably occur during the casting process, is of crucial technological importance for high-quality hot rolled plate products. Therefore, lab-scale tests were carried out under different typical thermomechanical loadings. Extensive data from optical microscopy was collected before and after deformation. The analysis shows that the average volume of pores evolves similar to the volume of an idealized arrangement of voids in an ideally plastic matrix. The average shape of the shrinkage pores, however, was found to be almost constant during deformation. Even though individual pores exhibit complex morphologies far from any idealized geometries, the overall evolution of a large number of pores is well captured by simple assumptions. In addition to the quantitative analysis, a schematic representation of this counter-intuitive behavior is provided. A simple ‘Gurson’-type void evolution equation was implemented in a three-dimensional Finite-Element model of the industrial hot rolling process. With the help of this mechanism-based process simulation the thermomechanical closure of shrinkage pores during the rolling process has been optimized for a variety of plate products.INTRODUCTION Aluminum alloys of the 7xxx series are widely used in the aircraft industry. They have to meet high quality standards regarding microstructure as well as mechanical properties. For hot-rolled aircraft plates, one of the most important quality requirements is that they are free from pores. Pores, however, are inevitably created during the casting process either due to shrinkage or due to the dissolution of gas from the melt. The pores have to be closed mechanically during the hot-rolling process. Therefore, the mechanism of so-called pore closure or void closure has a high technological relevance for the production of aircraft plates. The behaviour of voids in a ductile matrix subjected to mechanical deformation has been extensively studied, especially in the context of damage mechanics. A recent review (Besson et al., 2010) on modeling methods for ductile damage gives a good impression on how much experimental as well as theoretical effort has been dedicated to the problem of void evolution under mechanical loadings. Although void closure has been studied to a far lesser degree, it obeys to the same general theoretical evolution laws as void growth. The most basic theoretical result is that hydrostatic pressure drives void closure, while hydrostatic tension leads to void growth. The mechanism of void closure depends on the void shape. This is illustrated by the example of a flat penny-shaped void, which under compression obviously closes much faster than a sphere with the same volume. Theoretical models have been developed for the evolution of simplified void geometries, such as spheres or cylinders (e.g. Gurson, 1977), spheroidal (Gologanu et al., 1997) and ellipsoidal voids (Ponte-Castaneda, 1994). In industrial cast ingots, however, the pores exhibit very complex morphologies, which are far from any idealized geometry. X-ray tomography revealed ‘tortuous’ voids in a 5xxx aluminium alloy (Chaijaruwanich et al., 2006)."

Jan 1, 2018